I am installing a security license on Cisco 2911 Router for the first time. It already has a temporary license installed on it which is expiring soon. Cisco has already mailed me the procedure for installation. I want to know if i need to uninstall the previous license before installing the new one.
View 2 RepliesI’m stuck in some problem with installation of LMS4.0 in customer site.
- we purchase a LMS4.0(CWLMS-4.0-100-K9) but couldn’t install it on Windows server 2008 R2 64bit because those things don’t support each other.
- I need to upgrade the LMS4.0 to LMS4.2 that is supporting Windows server 2008 R2 64bit.
- So, I ordered following items via product update tool (url...) [code]
- In this status, how to install LMS4.2 with license for 100 devices? If I install R-PI12-BASE-K9 first, can i enter a licese for 100 devices for CWLMS-4.0-100-K9 into PI1.2?
How to install IP base liecense and Unified communication liecense in 2921 router?
View 1 Replies View Relatedhave a ACS 5.2 version installed on Vmware . I purchased below liscense
Product Name : L-CSACS-5-LRG-LIC=
Product Description : L-CSACS-5-LRG-LIC= : ACS 5 Large Deployment License (Electronic Delivery)
When i am trying to upgrade the liscense i am getting an Error " Liscense file installation failed : The liscense file must contain single base liscense "
The installation of an ACE-4710 throughput upgrade license licence (ACE-AP-02-UP1) failed with an error message :CH01AC03/Admin# license install disk0:ACE20111213081741975.lic.Installing license... failed: No space left on device. [code]
View 4 Replies View RelatedI am having Cisco 3845 series router with c3900-universalk9-mz.SPA.151-4.M2.bin IOS . I want to install new Licence on it for DATA. When i am trying to install licence on it i am facing the error "% Error: License installation failed with error: XML parsing failed".
View 4 Replies View RelatedWhat's the difference between VPN Plus license and Security Plus license. I have new 5520 shipped with VPN Plus license.Also does it require a seperate license for Anyconnect for Mobile and AnyConnect Essentials.
View 1 Replies View RelatedI need a router to connect to our ISP by BGP and in a future to a second ISP. Our ISP is going to provide us about 300.000 route entries by BGP. So router 2921 would be enough??? or should i go to a higher model?We are going to have 100Mbps with this ISP and probably in 3 months we'll have to double it. Also we'll need IPv6 support.I saw router performance [URL]f and it's has 480.000 PPS and 245 Mbps but for 64 bytes lenght packages. If the packets are bigger the throughput should be best I suppose... 1500 bytes about 5,5 Gbps. In the case you consider the model is sufficient, the flash or RAM should be increased?
View 4 Replies View RelatedIs there a recommended number of GRE tunnels that Cisco 2921 ISR router with default configuration (512MB DDR2 ECC DRAM) can support?
View 5 Replies View RelatedWe recently acquire a cisco 2921/K9 router to interface 2 networks
Network 1 : 169.254.XXX.XXX/16 on GigabitEthernet0/0 interface
Network 2 : 192.168.1.XXX/24 on GigabitEthernet0/1 interface
On the network 1 side there is a multicast source (169.254.200.200 destination : 225.0.0.1) on the network 2 side there is 1 receiver which is not multicast capable(old) but i want it to receive the multicast stream for the moment we configure the ip multicast-routing and each interface each interface with ip pim sparse-dense-mode then configure the GigabitEthernet0/1 in order to join the multicast group (using ip igmp static-group 225.0.0.1) and wireshark confirm that the multicast stream on the network 2 side from 169.254.200.200 -> 225.0.0.1 of course the receiver don't the stream, but if i force a "multicast to unicast" process inside the router it shall be ok.. after many hour of internet browsing i found 2 solution :
- NAT, [URL]
- multicast service reflection (Cisco documentation)
The NAT example don't work ,what is the best way to do this task.
I need to configure cisco router 2921 for snmp v3,
View 5 Replies View RelatedI just purchased thie Cisco 2921 router and have all the configuration completed except the Firewall and NAT. We have 4 supnets at our location on the router each with a DHCP handed from the router to our network. Any examples for the Firewall and Nat configurations?
View 6 Replies View RelatedWe have a 2300 RPS with single 1150WAC power supply (C3K-PWR-1150WAC) which is connected to one 2921 Router. But it is not backing the rotuer.
Router 2921 running IOS
c2900-universalk9-mz.SPA.152-2.T1.bin
I am getting the following logs:
*** External Redundant Power Supply is present, but type is unknown or not supported.***
%ENVMON-1-POWER_WARNING: : RPS Online Insertion and Removal is not supported.
Do we required any configuration to be done on Router end.
Note: The RPS is backing 2960 Switch.
I contact you due that I’m currently configuring a Router Cisco 2921 with an Etherswitch module. The specific inventory of Router Cisco 2921 is:
Router#show inventory,NAME: "CISCO2921/K9 chassis", DESCR: "CISCO2921/K9 chassis"
PID: CISCO2921/K9 , VID: V06 , SN: XXXXXXXXXXX
NAME: "High Speed WAN Interface Card - 1 Port Gigabit Ethernet on Slot 0 SubSlot 0", DESCR: "High Speed WAN Interface Card - 1 Port Gigabit Ethernet"
PID: HWIC-1GE-SFP , VID: V01 , SN: XXXXXXXXXXX"
[Code]....
I have a Cisco 2921 Router,with 3 giga interfacesi have a leased line for the internet with a public ip address and i want to configure this router as NAT /PAT gateway, so that users in my network can ue the internet by the router,my wan interface is g0/0 - ip 122.xx.xx.xx lan is g 0/1 -- 192.168.1.1 /24 . i have tried doing nat once but i was not able to make the wan port up.using cisco CP when i test the interface it givves error and i dont get internet to my users.
View 10 Replies View RelatedI have a trouble with PPTP VPN between Windows clients and Cisco 2921 router with RADIUS (IAS) authorization. When I try to connect to Cisco 2921 from Windows 7 using MS-CHAP v2 I receive error 778: it was not possible to verify the identity of server . Then I use PAP - everythig is OK. On Windows XP the same situation.
Cisco config:
version 15.0
service timestamps debug datetime msec
[Code].....
I just got a brand new Cisco 2951 router that has built-in 3 gigabit interfaces cards. We want to add additonal 2 GE EHWIC-1GE-SFP-CU card to it. When it booted up and type show inventory, it did not detect the presence of the card. There was light on at the back of it. I have checked the compatibility on Cisco. The card is compatible with this router. Do we have to install the card with special instructions in order for the router to see it?
View 1 Replies View RelatedI have installed a VWIC2-1MFT-G703 module into cisco 2921 router, I can verify the card by show inventory command. but in show run, I do not see the E1 controller card there. this card is used for TPG lease line for data only. Those card is compatible with new 2921 router? or need some extra command to bring it up?
View 2 Replies View RelatedI am getting the following errow message while trying to create a VPN tunnel between an ASA5520 and a 2921 router. [code]
View 9 Replies View Relatedi m planning to use the 2921 router for both mpls and internet connection , to 2 different isp also am planning to use bgp with a public providor independant
i m planning to buy sla for the mpls link
I have one new cisco 2921 router but after first login into the new router . I have made some configuration but forget to change the default password . Now i am unable to login into the router after first log off but iam not able to recover password because the router don't have any external flash memory.
View 4 Replies View RelatedDoes the E1000 router come with a default security setting upon installation using the supplied CD?
View 9 Replies View RelatedIf Cisco Router 2921 base load supports NAtting? I am looking to order a Router and want to make sure the new 2900 routers support Natting.
View 2 Replies View RelatedI am configuring a vpn ipsec tunnel with cisco isr 2921 router and Watchguard edge 1250e. I have the watchguard configured so I just need to make sure I have everything setup on the cisco side. At this point, there is no communication as I am not sure if I configured it correctly. Should I do the crypto map on g 0/0 or dialer 1?
aaa new-model
!
!
!
!
!
!
!
aaa session-id common
!
!
no ipv6 cef
[code]......
What I’m looking to do is setup a net-flow monitor for traffic going across a PIX firewall. I know unfortunately I can’t do this directly from the PIX because it does not support net-flow.
I do have a 2921 router on the same network that I have net-flow enabled to monitor traffic across the MPLS Connection.
Since the traffic for the MPLS is going out a direct interface I have applied the IP Flow egress/ingress commands to that interface to obtain the net-flow data I need. The PIX firewall however is not a direct interface so this can’t be done. I have done a little reading and believe I could use a policy map to create a “filter” so that any traffic that meets the ACL associated with the Policy-Map would get sent to net-flow monitor.
My question is how do I set that up so that so I can have the two net-flow data “streams/sources” go to separate net-flow ports so that I can monitor them independently of each other or is that not possible?
Both devices are connected to a 3750X switch; however neither is connected to a 10GB port. To my understanding that means I can’t run net-flow on the switch itself.
I want to connect 2 ISP links into one Gigabit-interface on my Router 2921, can any one tell me how to do that ? sub-interface creation is not possible on cisco 2921
View 1 Replies View RelatedIs there any risk to install an HWIC-2FE card into a production 3845 router while it is in a powered up state? Is it recommended to power it down first, then install it?
View 3 Replies View RelatedHow do I install or get a installation disk for D-link model dir-601 Router
View 1 Replies View RelatedI am planning to set to my new house a secure network with Cisco firewall. I have practically no experience with firewalls and specially no with ASA programming. Still I have quite a clear picture what the system will look like. But when I first opened the ADSM screen I was freaked out about the amount of selections to be made. I cannot even figure out where I shoud start from! I am afraid that even thou I am very good with computers, it will take years to get understand all this data not to mention of configuring the device.
At the moment the situation is as follows:
- Firewall is set as factory default and it cannot not get to internet. I can't figure out what is blocking the traffic out. Logs does not work.
- Cable modem router has DHCP, NAT and SPI firewall ON.
- Outside has line/link up and IP is DHCP configured, but no traffic.
- 5505s' DHCP is now off but tested and working
- No VPN tunnels built (never built one and don't know how to do it)
- No extra routes / rules / profiles / policies etc. done. All is at default/auto status.
How can I get a installation CD for a WRT54GX2 Wireless router? Can you download from internet?
View 3 Replies View Relatedthe cisco 2921 Router has a default ip hhtp access class command found in it. Just i changed the default IP to the new ip i will use.The Router is accessable from the LAN only but not from the internet configured the Public ip . I think this is due to the standard access list 23 . how will i access the Router from the Internet using the Public IP.
View 6 Replies View RelatedI have 2 links to 2 different departments switch with an up link of 10mb. I want to guarantee that both departments get at least 5mb, but can use part of the other 5mb that not in use. Is this possible?
View 3 Replies View RelatedI have one interface setup to a Cisco 2921 router connected to a Cable modem.DHCP is on the 2921.when I connect to the ssid for my guest i'm redirected to the authentification portal 1.1.1.1 .i'm putting valide credential and when pressing the submit button .. it just go anywhere.
I have setup another SSID with a psk and it's working fine.. getting ip and able to browse internet.From what i have read... it's apparently DNS issue on my router.. but what should I check.