Cisco WAN :: RPS 2300 Not Backing Router 2921
Oct 2, 2012
We have a 2300 RPS with single 1150WAC power supply (C3K-PWR-1150WAC) which is connected to one 2921 Router. But it is not backing the rotuer.
Router 2921 running IOS
c2900-universalk9-mz.SPA.152-2.T1.bin
I am getting the following logs:
*** External Redundant Power Supply is present, but type is unknown or not supported.***
%ENVMON-1-POWER_WARNING: : RPS Online Insertion and Removal is not supported.
Do we required any configuration to be done on Router end.
Note: The RPS is backing 2960 Switch.
View 2 Replies
ADVERTISEMENT
Jun 30, 2011
Using a Cisco 2921 router with an RPS 2300, I came across a table in the 2900 Hardware Installation Guide that I can hardly believe: table 5-3 seems to tell me that in order to back up ONE 2921 with RPS power, I will need an RPS with TWO 750 Watt or TWO 1150 Watt power supplies. Is it really true that I need to throw at least 1500 Watts of backup power at a router that has a main power supply of approx 300 W?
View 13 Replies
View Related
Jun 23, 2011
I have te E4200. When I backed up and restored my media server settings were not there as well as ftp, I found this out upgrading to 1.0.02 that turned out to be a huge waste of time anyways.
View 7 Replies
View Related
Aug 26, 2007
how to configure an IPaddress for a PWR-RPS 2300?.I tried finding info on the website but no luck as yet. RPS 2300 will be used on stack of 3750E series switches.
View 3 Replies
View Related
Dec 7, 2011
I want to capture RPS related alarm on SNMP server for RPS2300 and cisco 3750d switch
View 1 Replies
View Related
Jul 18, 2012
Can I check I've understood the ACS backup and restoration procedure?A backup run from exec as "backup <filename> repository <repository name>" is the same command run automatically by "System Administrator -> Scheduled Backups" in the GUI, just scheduled for me...That backup is enough to completely restore ACS to its state at the time of the backup, including ACS config (Users, Devices, NDGs, etc.) and the View database (reports, historical data, etc.)It's entirely separate from the backups ACS View makes as part of it's purging action. (I only need those if I want to go way back in time, I don't need them to restore a functioning ACS with the recent reports and logs) if I still have a working ACS left after the primary dies, is it not just easier to promote the survivor to primary and then add the replacement in as a secondary and let replication restore the configs? Perhaps re-promote the new box to primary afterwards?
View 7 Replies
View Related
Sep 21, 2012
I have several network shares in my home using two different NAS devices.I am looking for recommendations for backing up the data on these devices.I currently use CrashPlan for backing up my computers.I have 1 share (documents) that I would like to somehow get backed up to CrashPlan (I'm not specifically tied to CrashPlan, it's just what I'm using now). The rest of the shares I would like to just backup locally in the event of hard drive failure.I have tried having my iMac mount the documents share automatically and include that in the CrashPlan backup, but it seems unreliable.
View 6 Replies
View Related
Sep 14, 2011
I've just got a brand new 1 TB external hard drive. I want to use this to back my computer files on. I move back to University soon and ill probably get robbed, so i was thinking, if I were to leave this new drive back home on my old machine, could i put files onto it over the internet? Of course id have to make sure the machine at home is on but thats no problem.
View 2 Replies
View Related
Jun 9, 2011
Is this known bug that you cannot backup (export) full running or startup config from this switch? Will this be fixed in next firmware? (btw, still no new firmware with CDP support for this script altough sales literature mentions that it should have already been available...)Switch does let you backup configuration as text file (which looks similar to normal IOS config syntax), but it doesn't contain all settings so the file is pretty much useless to restoring the config to another switch.At least following settings are missing from the file:
- management interface config (including DNS settings)
- passwords
- remote syslog server config
- SNTP server config
- IGMP config
- LLDP config
View 2 Replies
View Related
May 8, 2012
I have a home directory on a linux server and i would like to figure out how can i schedule regular backups/syncs onto an external hard drive on a windows machine.
View 8 Replies
View Related
Feb 3, 2013
Region : France
Model : TD-W8151N
Hardware Version : V3
Firmware Version : latest
ISP : OrangeF
Received today my modem, configured it with some effort but it works... Now i'm trying to save ma config file (rom-0) using web interface, and when clicking on Maintenance > Firmware, i'm always getting:bug.jpg Seems to be a big bug
View 4 Replies
View Related
Jul 10, 2012
I am trying to research the possiblity of backing up IOS and configurations from an Etherswitch module, and being able to store the files onto the Host Router's flash (3925 ISR). and then being able to recover that IOS and configuration, in case I have to replace the Etherswitch Module.
View 1 Replies
View Related
Oct 13, 2011
I need a router to connect to our ISP by BGP and in a future to a second ISP. Our ISP is going to provide us about 300.000 route entries by BGP. So router 2921 would be enough??? or should i go to a higher model?We are going to have 100Mbps with this ISP and probably in 3 months we'll have to double it. Also we'll need IPv6 support.I saw router performance [URL]f and it's has 480.000 PPS and 245 Mbps but for 64 bytes lenght packages. If the packets are bigger the throughput should be best I suppose... 1500 bytes about 5,5 Gbps. In the case you consider the model is sufficient, the flash or RAM should be increased?
View 4 Replies
View Related
Feb 20, 2013
Is there a recommended number of GRE tunnels that Cisco 2921 ISR router with default configuration (512MB DDR2 ECC DRAM) can support?
View 5 Replies
View Related
Jul 11, 2012
I am installing a security license on Cisco 2911 Router for the first time. It already has a temporary license installed on it which is expiring soon. Cisco has already mailed me the procedure for installation. I want to know if i need to uninstall the previous license before installing the new one.
View 2 Replies
View Related
Apr 15, 2013
We recently acquire a cisco 2921/K9 router to interface 2 networks
Network 1 : 169.254.XXX.XXX/16 on GigabitEthernet0/0 interface
Network 2 : 192.168.1.XXX/24 on GigabitEthernet0/1 interface
On the network 1 side there is a multicast source (169.254.200.200 destination : 225.0.0.1) on the network 2 side there is 1 receiver which is not multicast capable(old) but i want it to receive the multicast stream for the moment we configure the ip multicast-routing and each interface each interface with ip pim sparse-dense-mode then configure the GigabitEthernet0/1 in order to join the multicast group (using ip igmp static-group 225.0.0.1) and wireshark confirm that the multicast stream on the network 2 side from 169.254.200.200 -> 225.0.0.1 of course the receiver don't the stream, but if i force a "multicast to unicast" process inside the router it shall be ok.. after many hour of internet browsing i found 2 solution :
- NAT, [URL]
- multicast service reflection (Cisco documentation)
The NAT example don't work ,what is the best way to do this task.
View 8 Replies
View Related
May 19, 2013
I need to configure cisco router 2921 for snmp v3,
View 5 Replies
View Related
Jun 27, 2011
I just purchased thie Cisco 2921 router and have all the configuration completed except the Firewall and NAT. We have 4 supnets at our location on the router each with a DHCP handed from the router to our network. Any examples for the Firewall and Nat configurations?
View 6 Replies
View Related
Feb 25, 2013
I contact you due that I’m currently configuring a Router Cisco 2921 with an Etherswitch module. The specific inventory of Router Cisco 2921 is:
Router#show inventory,NAME: "CISCO2921/K9 chassis", DESCR: "CISCO2921/K9 chassis"
PID: CISCO2921/K9 , VID: V06 , SN: XXXXXXXXXXX
NAME: "High Speed WAN Interface Card - 1 Port Gigabit Ethernet on Slot 0 SubSlot 0", DESCR: "High Speed WAN Interface Card - 1 Port Gigabit Ethernet"
PID: HWIC-1GE-SFP , VID: V01 , SN: XXXXXXXXXXX"
[Code]....
View 1 Replies
View Related
Jan 14, 2013
I have a Cisco 2921 Router,with 3 giga interfacesi have a leased line for the internet with a public ip address and i want to configure this router as NAT /PAT gateway, so that users in my network can ue the internet by the router,my wan interface is g0/0 - ip 122.xx.xx.xx lan is g 0/1 -- 192.168.1.1 /24 . i have tried doing nat once but i was not able to make the wan port up.using cisco CP when i test the interface it givves error and i dont get internet to my users.
View 10 Replies
View Related
Oct 23, 2011
I have a trouble with PPTP VPN between Windows clients and Cisco 2921 router with RADIUS (IAS) authorization. When I try to connect to Cisco 2921 from Windows 7 using MS-CHAP v2 I receive error 778: it was not possible to verify the identity of server . Then I use PAP - everythig is OK. On Windows XP the same situation.
Cisco config:
version 15.0
service timestamps debug datetime msec
[Code].....
View 6 Replies
View Related
Oct 2, 2011
I just got a brand new Cisco 2951 router that has built-in 3 gigabit interfaces cards. We want to add additonal 2 GE EHWIC-1GE-SFP-CU card to it. When it booted up and type show inventory, it did not detect the presence of the card. There was light on at the back of it. I have checked the compatibility on Cisco. The card is compatible with this router. Do we have to install the card with special instructions in order for the router to see it?
View 1 Replies
View Related
Jun 5, 2012
I have installed a VWIC2-1MFT-G703 module into cisco 2921 router, I can verify the card by show inventory command. but in show run, I do not see the E1 controller card there. this card is used for TPG lease line for data only. Those card is compatible with new 2921 router? or need some extra command to bring it up?
View 2 Replies
View Related
Sep 21, 2011
I am getting the following errow message while trying to create a VPN tunnel between an ASA5520 and a 2921 router. [code]
View 9 Replies
View Related
Apr 4, 2011
i m planning to use the 2921 router for both mpls and internet connection , to 2 different isp also am planning to use bgp with a public providor independant
i m planning to buy sla for the mpls link
View 9 Replies
View Related
May 16, 2012
I have one new cisco 2921 router but after first login into the new router . I have made some configuration but forget to change the default password . Now i am unable to login into the router after first log off but iam not able to recover password because the router don't have any external flash memory.
View 4 Replies
View Related
Nov 13, 2012
If Cisco Router 2921 base load supports NAtting? I am looking to order a Router and want to make sure the new 2900 routers support Natting.
View 2 Replies
View Related
Aug 28, 2012
I am configuring a vpn ipsec tunnel with cisco isr 2921 router and Watchguard edge 1250e. I have the watchguard configured so I just need to make sure I have everything setup on the cisco side. At this point, there is no communication as I am not sure if I configured it correctly. Should I do the crypto map on g 0/0 or dialer 1?
aaa new-model
!
!
!
!
!
!
!
aaa session-id common
!
!
no ipv6 cef
[code]......
View 4 Replies
View Related
Nov 15, 2012
What I’m looking to do is setup a net-flow monitor for traffic going across a PIX firewall. I know unfortunately I can’t do this directly from the PIX because it does not support net-flow.
I do have a 2921 router on the same network that I have net-flow enabled to monitor traffic across the MPLS Connection.
Since the traffic for the MPLS is going out a direct interface I have applied the IP Flow egress/ingress commands to that interface to obtain the net-flow data I need. The PIX firewall however is not a direct interface so this can’t be done. I have done a little reading and believe I could use a policy map to create a “filter” so that any traffic that meets the ACL associated with the Policy-Map would get sent to net-flow monitor.
My question is how do I set that up so that so I can have the two net-flow data “streams/sources” go to separate net-flow ports so that I can monitor them independently of each other or is that not possible?
Both devices are connected to a 3750X switch; however neither is connected to a 10GB port. To my understanding that means I can’t run net-flow on the switch itself.
View 3 Replies
View Related
Oct 6, 2012
I want to connect 2 ISP links into one Gigabit-interface on my Router 2921, can any one tell me how to do that ? sub-interface creation is not possible on cisco 2921
View 1 Replies
View Related
Nov 21, 2012
the cisco 2921 Router has a default ip hhtp access class command found in it. Just i changed the default IP to the new ip i will use.The Router is accessable from the LAN only but not from the internet configured the Public ip . I think this is due to the standard access list 23 . how will i access the Router from the Internet using the Public IP.
View 6 Replies
View Related
Dec 12, 2012
I have 2 links to 2 different departments switch with an up link of 10mb. I want to guarantee that both departments get at least 5mb, but can use part of the other 5mb that not in use. Is this possible?
View 3 Replies
View Related
Apr 21, 2013
I have one interface setup to a Cisco 2921 router connected to a Cable modem.DHCP is on the 2921.when I connect to the ssid for my guest i'm redirected to the authentification portal 1.1.1.1 .i'm putting valide credential and when pressing the submit button .. it just go anywhere.
I have setup another SSID with a psk and it's working fine.. getting ip and able to browse internet.From what i have read... it's apparently DNS issue on my router.. but what should I check.
View 4 Replies
View Related
