Cisco :: 3945 Router Error While Adding In CiscoWorks
May 29, 2010
I have a Cisco 3945 Router and when we try to add the same into the Cisco Works it gives me an error saying " CM0056 Config fetch failed for 192.168.xx.xx Cause: CM0204 Could not create DeviceContext for 1238 Cause: CM0206 Could not get the config transport implementation for 192.168.xx.xx Cause: UNKNOWN Action: Check if required device packages are available in RME. Action: Check if protocol is supported by device and required device package is installed.
We are using LMS version 2.6. Any info on the latest router 3945 with support or not.
View 6 Replies
ADVERTISEMENT
Nov 24, 2012
I upgraded CiscoWorks LMS from 3.0 to 3.2 today. Everything worked prior to the upgrade.The upgrade was successful, with no errors, and all services started. check everything and I see no problem. The system creates the file MDCSupportInformation.zip me clean without any content.I add the installation log file;And tell them that after upgrading to 3.2, you carge the following patches:
LMS321-win-CSCtr77570-0.zip,
cm5.2.1-nt-CSCtw88763-1.0.zip,
lms3.2.1-win-CSCts95764-0.zip,
lms3.2.1-win-CSCts82530-0.zip
in that order.He added the logs generated by the LMS services Tomcat and Apache
View 4 Replies
View Related
Sep 17, 2012
I used the below syntax to check the snmpwalk to an interface of a cisco 7606-s router from an LMS 4.0 version cli.
NMSROOT/Objects/jt/bin>snmpwalk -v 2c -c <snmp-string> <ip-addr> 1.3.6.1.2.1.31.1.1.1.6
Timeout no response from <ip_address>
This is the error im getting in cli prompt. But i could see that reports are generating.If i try with the loopback ip address, i get proper snmpwalk outputs.. I have increased the timeout and retry options..
View 3 Replies
View Related
Aug 14, 2011
Whenever I tried to do backup of CiscoWorks from GUI, I am receiving a error message"Backup failed. ERROR(292): C:PROGRA~1CSCOpx/backup.LOCK file exists, look into the log file C:/PROGRA~1/XCSCOpx/log/dbbackup.log for more details". backup.LOCK file size is 0KB.I am using LMS 3.2; RME 4.3.0;CM 5.2.0
View 1 Replies
View Related
Sep 10, 2012
This is what the Log shows when I try adding a 4404 to NCS
[2012-09-11 12:37:04,199] [ICE Service[ 1]Thread: 7] [inventory] [INFO ] - Complete inventory for deviceid 11020009 at Tue Sep 11 12:37:04 EST 2012. Total time taken to collect inventory in milliseconds = 1304
[2012-09-11 13:48:41,707] [http-443-10] [inventory] [INFO ] - Device with id 11020010 is managed state now, initial inventory collection started
[2012-09-11 13:48:41,768] [http-443-10] [inventory] [INFO ] - Initial inventory collection completed for device with id 11020010 without exception
[2012-09-11 13:48:41,822] [ICE Service[ 1]Thread: 8] [inventory] [INFO ] - Enter collect inventory for deviceid 11020010 at Tue Sep 11 13:48:41 EST 2012
[2012-09-11 13:48:41,960] [ICE Service[ 1]Thread: 8] [inventory] [INFO ] - Called InventoryCollectorEngineXdeImpl.call()for device ID = 11020010.
[2012-09-11 13:48:42,045] [ICE Service[ 1]Thread: 8] [inventory] [INFO ] - Invoking FeatureRunner [returned result: mib2-bootstrap] for MNE collection of device: 11020010)
[2012-09-11 13:48:42,159] [ICE Service[ 1]Thread: 8] [inventory] [ERROR] - 192.168.12.77 No matching device profile found.......
[code]....
View 3 Replies
View Related
Nov 3, 2011
My firmware is 1.35NA and have a schedule established. When I try to add a policy for access control, I can select a policy name but when I hit "next", I get an error stating "Internet Explorer has stopped working" and wants to close. I was able to add policies previously but can not any more.
View 3 Replies
View Related
Nov 8, 2012
I am trying to find out what the 'normal' operating temperature of the CPU in a 3945 router is? We have just replaced some 2800 routers for 3945's and the NMS server initially complained about the new router CPU temperature being too high. Compared to the 2800 the CPU temperature is much hotter - 50 degrees celcius as opposed to 20-smothing degrees. I have searched but can't find what are considered 'normal'?
This is the output:
router#sho environment allSYSTEM POWER SUPPLY STATUS==========================Internal Power Supply 1 Type: DCInternal Power Supply 1 12V Output Status: Normal
[Code].....
View 3 Replies
View Related
Nov 10, 2011
I need to upgrade a router from a 2811 to a 3945.
2811 has the following modules:
View 1 Replies
View Related
Oct 3, 2012
I have some lags on my 3945 router. From show ip nat statistics there is following output:
BR1#show ip nat statistics
Total active translations: 20 (0 static, 20 dynamic; 20 extended)
Peak translations: 8877, occurred 1w0d ago
Outside interfaces:
GigabitEthernet0/0, GigabitEthernet0/1
[code].....
View 1 Replies
View Related
Jan 15, 2013
Is Cisco 3945 router support URL based filtering . For example to block website [URL] but not the main site [URL].
View 1 Replies
View Related
Mar 15, 2012
I reported a really strange issue on a Cisco Router 3945. Here below info about release software used: [code] Please look at a brief extract of router running configuration file: [code] It’s an easy configuration of Extended ACL and the application on an Ethernet interface. The expected result is:
- The interface works properly (because access list is permitting every kind of data traffic in input)
- Checking “show access-list 180”, the counter of matched packets increments for all the packets that are forwarded inside the fa0/0/1.
But actually the Fastethernet 0/0/1 drops all the packets as if all the packets don’t match with access list (And this behavior is really incredible). The interface couldn't be used anymore because any kind of data traffic is denied.
View 14 Replies
View Related
May 18, 2011
3945 Router IOS Required for support VoFR Feature
View 1 Replies
View Related
Aug 11, 2011
I just got my first 3945 router and E3/T3 Network cards and when I do a sho ver I can see the E3/T3 card but when I do a show run all I see are the 3 GE interfaces.
View 1 Replies
View Related
Aug 9, 2011
I am getting the following message from a 3945 router: %CERM-4-TX_BW_LIMIT: Maximum Tx Bandwidth limit of 85000 Kbps reached for Crypto functionality with securityk9 technology package license.
That router has 8 Gre/IPsec tunnels and one of those tunnels is 100Mbps.The question is, could I get 100Mbps as the sum of all tunnels, or is there a restriction to 85Mbps ??
View 2 Replies
View Related
Dec 21, 2012
When I try to configure a voice port (like voice-port 0/0/0:15) after doing a conf t, it gives me an error of invalid input detected.We are using a Cisco 3945. We have successfully setup 3825 and 2851 in the past.
View 2 Replies
View Related
Dec 10, 2012
On a 3945 voicegateway,I want to remove a wave file (announcement), with the purpose that a new one can be automaticaly downloaden from UCCE to the box.Is there a way to do that automaticaly with SNMPSET <voicegateway> <MIB OID> <??wave file name??> <reload>
EDIT: or clear the cache, which it should be I think. (all wave file cache, or only one file, not sure what should be used and/or what is possible
View 1 Replies
View Related
Dec 2, 2012
the router IPSec VPN config for remote users using Cisco VPN Client 5.0.07
Router 3945 IOS C3900-UNIVERSALK9-M Version 15.1(4)M4
Here is VPN related config part and log from router and client.
aaa new-model
!
!
aaa authentication login default none
aaa authorization network default none
!
!
crypto isakmp policy 5
encr aes 256
authentication pre-share
[Code]...
I highlighted strings with possible problems of of unabling to connect but doesn't know what to do with it.
View 4 Replies
View Related
Aug 31, 2012
I have been assigned the task of configuring a 3945 router for sip circuit. [code] Where am I supposed to put this config? On the bonded serial link?
View 2 Replies
View Related
Feb 7, 2013
We just recently purchased a 3945 ISR G2 router and have a SRE-910 module (with two hard drives) configured in a Raid 1. We are running a stand-alone version of ESXi on the service module and I'm trying to figure out how to monitor the status of the Raid on the drives (along with other health issues). SNMP has revealed nothing so far and even opening a support case for which MIB's to use has proved fruitless. All the documents I find on monitoring the modules say to use LMS which is now Cisco Prime. I've downloaded the trial copy, put in the SNMP settings and scanned the router. I get device results and it shows that I have the SRE-910 module installed, but I get no other configuration / device informaiton from the module itself.
I tried to create a new Monitoring template using the NAM health as the base template (which I'm assuming this is the correct template). Unfortunately, when I actually try to deploy the template against the discovered router, I get an 'Unexpected end of list' error which makes me assume I'm still doing something wrong.
View 1 Replies
View Related
May 20, 2010
I understand that the password has to be changed the first time we login to Cisco 3945 router but i failed to do that and its not allowing me to connect using default username/password.
View 7 Replies
View Related
Jun 15, 2011
We have Cisco 3945 Router and generating crashinfo while firing PRI from this Router.
View 1 Replies
View Related
Nov 15, 2011
Recently, I have increase to 4G memory ram to the router 3945 but when I show version, it does not state there are 4G in there but still showing the old mem ram size. Why is that so ?
View 3 Replies
View Related
Dec 5, 2012
CISCO 3945 Routers - Are the 3945 Router power supplies load balanced by default? We are trying to determine if our switch/server rack at our remote location has maxed out it's power load requirements. I just need to know if the 3945 power supplies load balance by default or if the redundant power supply is ON but not really providing the router with power and is just there incase the other power supply fails .
View 3 Replies
View Related
Dec 3, 2012
We have installed a VWIC3-2MFT card on a Cisco 3945 voice gateway but the router doesnt detect the card. out put is as below;
Router Version
============
System image file is "flash0:c3900-universalk9-mz.SPA.150-1.M.bin"
Cisco CISCO3945-CHASSIS (revision 1.0) with C3900-SPE150/K9 with 980992K/67584K bytes of memory.
[Code]....
View 8 Replies
View Related
Jun 29, 2012
We are having problems with a two router 3945 in HSRP and a switch 2960.The two routers are connected to the switch 2960 through differentes ports. The problem is that we loose connection between the router and the switch.When we excute the command: show cdp neighbor at router, it shows nothing.If we try to make ping to the 2960 switch it is no reachable.If we make ping to the other router 3945 it is not reachable.All other function of the router are o.k.We are attaching the IOS of the routers and switch 2960 and a document in which make reference to a BUG in which mention about arp overwrite due arp attack which produce DoS.
View 2 Replies
View Related
Apr 10, 2012
I am using DHCP/TFTP to autoconfigure a 3945 router. The router properly obtains an IP address and finds the correct TFTP server. The issue lies in the download of the configuration file from the TFTP server. The router downloads the file, gives the "Ok" message, and prompts you to press Return to get started. When I view the running-config, several commands are missing from the Serial 0/0/0 section (HWIC-2T). If I modify the config file on the TFTP server to use Serial 0/0/1 instead and repeat the process, the configuration file loads without any issues and Serial 0/0/1 has all of the commands.
I also tried moving syntax around in my config file, but the end result is still the same. If I use Serial0/0/0 - I don't get all of the commands. If I use Serial 0/0/1, I do.
View 1 Replies
View Related
Mar 12, 2013
The router 1841 is connected directly to the layer switch. the network diagram is below:
Office A --> Switch (L3) --> Router 1841 --> Internet --> Office B
However, when I transfer the file from Office A to office B, the speed very slow ( only around 40 kb/second), and there are an input error and CRC error:
Cisco-R1841#sh interfaces FA0/1
FastEthernet0/1 is up, line protocol is up
Hardware is Gt96k FE, address is 0019.e02f.03dd (bia 0019.e02f.03dd)
[Code]......
View 5 Replies
View Related
May 19, 2011
Application is that need to configure the VOIP with the existing Frame relay network ,where VOFR command is not shown in the router when type yhe command router config#dial-peer voice 123 need vofr On the 3945 router where in the router it is not accepting the above command,
View 8 Replies
View Related
Jul 13, 2011
At present we are using the Ciscoworks LMS bunde 3.0. I would like to upgrade to LMS 3.1.
My Question: Is it possible to upgrade to LMS 3.1 with using the existing LMS 3.0 license.
View 2 Replies
View Related
Aug 31, 2011
There was a interface down in one of critical devices in the network.that particular log is not captured by the ciscoworks(DFM-alerts).
View 1 Replies
View Related
Oct 24, 2012
I am trying to get CiscoWorks LMS 4.0 to connect to my routers in order to back up configurations, but I am getting SSH authentication failures reported in the router logs (and archiving fails).
The credentials LMS is using is a username and password with priviledge 15: the account is established in TACACS+. I can log into the devices directly with this user account.However, I cannot TFTP from the routers to the LMS either (I get a permission denied message in the router).
LMS did manage to fetch some configs, but 90% of my devices are having this issue.
View 4 Replies
View Related
Sep 11, 2011
I need download LMS 4.0 eval trial. But i can't see any link down on url...
View 1 Replies
View Related
Oct 23, 2011
I upgraded the LMS 4.0 with LMS 4.0.1 but now the events are removed of Fault View. The equipments than I am monitoring are: ME-3600, ME-3800 and ASR 9000. This is a configuration problem or I have to update something else?
View 1 Replies
View Related
