Cisco :: LMS 3.2 Logs Missed In Ciscoworks?
Aug 31, 2011There was a interface down in one of critical devices in the network.that particular log is not captured by the ciscoworks(DFM-alerts).
View 1 Replies
ADVERTISEMENT
Cisco Switching/Routing :: Access-list Logging Rate-limited Or Missed XXXX Packets On 3560G
Jun 3, 2012I'm getting this error message on syslog server (Kiwi syslog)access-list logging rate-limited or missed XXXX packets i did the following commands but still I'm getting the error :logging buffered 16386 debugginglogging rate-limit all 5000no logging consoleno logging monitorip access-list logging interval 30000ip access-list log-update threshold 30000 i don't want to report to the console or monitor i want to report direct to syslog server, because I'm monitoring all the traffic (permit ip any any log) !
View 2 Replies View RelatedCisco :: Ciscoworks Upgrade To LMS 3.1?
Jul 13, 2011At present we are using the Ciscoworks LMS bunde 3.0. I would like to upgrade to LMS 3.1.
My Question: Is it possible to upgrade to LMS 3.1 with using the existing LMS 3.0 license.
Cisco :: SSH Authentication Failure CiscoWorks LMS 4.0
Oct 24, 2012I am trying to get CiscoWorks LMS 4.0 to connect to my routers in order to back up configurations, but I am getting SSH authentication failures reported in the router logs (and archiving fails).
The credentials LMS is using is a username and password with priviledge 15: the account is established in TACACS+. I can log into the devices directly with this user account.However, I cannot TFTP from the routers to the LMS either (I get a permission denied message in the router).
LMS did manage to fetch some configs, but 90% of my devices are having this issue.
Cisco :: Link Download Ciscoworks LMS 4.0
Sep 11, 2011I need download LMS 4.0 eval trial. But i can't see any link down on url...
View 1 Replies View RelatedCisco :: Fault View CiscoWorks LMS 4.0.1?
Oct 23, 2011I upgraded the LMS 4.0 with LMS 4.0.1 but now the events are removed of Fault View. The equipments than I am monitoring are: ME-3600, ME-3800 and ASR 9000. This is a configuration problem or I have to update something else?
View 1 Replies View RelatedCisco :: CiscoWorks With LMS 4.x NetShow Jobs URL
Jul 10, 2011I have upgraded our LMS 3.x to the new LMS 4.x Version. have installed the new 4.x on an new server and importet the backup.
I have importet a Certificate and have enabled the Browser-Server Security Mode, Enabled I added some new Netshow Jobs which run every day.
I get the email from the jobs and the URL in the email but, URL
When i click on the link i only get:
Forbidden: You don't have permission to access /rme/NSViewJobResults.do on this server.
Additionally, a 403 Forbidden error was encountered while trying to use an ErrorDocument to handle the request.
i must change the link to Urls there anywhere an option to edit the text which is send with the jobs, to fix the url?
Cisco :: CiscoWorks LMS 4.0.1 - Could Not Generate The Report
Sep 26, 2011I am running CiscoWorks LMS 4.0.1 since 6 months and I wanted to generate today a report about the interface utilization on 2 Cisco switches (Catalyst 3750G). The corresponding job is created, it runs and then i get "succeeded with info" in the "Run Status" column. When I want to click then on the "View Report" link, I get the following error: "Could not generate the report. Either data is not available for the specified duration or the report job failed."
I tried the same procedure with 2 other switches but I have got the same result.
Cisco :: CiscoWorks Appliance In T2000
Jul 25, 2011A while back we were looking into upgrading our SUN/Oracle server to better service our CiscoWorks. Our vendor (partnered Cisco Vendor) told us that Cisco was developing an appliance like WCS and CNR that runs Redhat for CiscoWorks.Does any one have any info on this or could this be a rumor?
We do not run Windows devices on any of our network enterprise and this would be so cool!
Oracle is getting to be a clone of Windows..in our opinion
If this is true, I will happy to sit and wait for it.
We now run LMS 4.0 on a SUN/Oracle T2000 and it seems to be bottlenecking.
Cisco :: How To Get Ciscoworks LMS 4.0.1 Serial Number
Dec 11, 2011How to get Ciscoworks LMS 4.0.1 serial number ? I need that to put the product under mainrtenance, and I can't manage to get it.
View 2 Replies View RelatedCisco :: Configuring Rcp On Ciscoworks LMS 2.5 And 3560 Switch
Jul 13, 2011I am having LMS 2.5 and nearly 50 cisco 3560 in my network. And I want to configure rcp. How can I do it.
View 1 Replies View RelatedCisco :: LMS 4.0 / How To Integrate NetFlow To Some Ciscoworks Module
Jun 20, 2012how to integrate NetFlow to some Ciscoworks module.
View 3 Replies View RelatedCisco :: LMS 3.2 CiscoWorks Daemon Manager Does Not Startup
Dec 20, 2010When trying to start CiscoWorks Daemon Manager i get the following message:"The CiscoWorks Daemon Manager service on local computer started and the stoped. Some services stop automatically if they are not in use by other services or programs."I have tring starting the service from DOS also and get,E:Program FilesCSCOpxsetupsupport>net start crmdmgtdThe CiscoWorks Daemon Manager service is starting.The CiscoWorks Daemon Manager service could not be started. The service did not report an error. More help is available by typing NET HELPMSG 3534.
View 11 Replies View RelatedCisco :: Configuring Email Alerts From CiscoWorks LMS 4
Nov 6, 2012I am looking for a way to get CiscoWorks LMS 4 to send me an email alert when a switch port goers into a security violation (err-disabled).
View 2 Replies View RelatedCisco :: Cat3750x Stack Upgrade From CiscoWorks
Jul 26, 2011I am trying to use Ciscoworks LMS3.2 with RME 4.3.1. to upgrade many, many Cat3750x stacks we have laying around. The problem I am having is that Ciscoworks downloads the new image to the Stack’s master switch only and not to all switches. When I reload the stack after the download, any switch could become the master. I already set up the priority to always have the same master, but the process is unreliable and more than once I ended up with another switch as a master. In any case if the master is not the switch with the new image, the stack will keep the old image as their running image and the switch with the newer image has problems joining the stack (after a while it downgrades and become stable)I know how to do it manually, but I was hoping Ciscoworks would be able to do this for me. It would make my life much easier.
View 1 Replies View RelatedCisco :: CiscoWorks Won't Start After LMS Upgrade 3.0 To 3.2 / Error 502
Nov 24, 2012I upgraded CiscoWorks LMS from 3.0 to 3.2 today. Everything worked prior to the upgrade.The upgrade was successful, with no errors, and all services started. check everything and I see no problem. The system creates the file MDCSupportInformation.zip me clean without any content.I add the installation log file;And tell them that after upgrading to 3.2, you carge the following patches:
LMS321-win-CSCtr77570-0.zip,
cm5.2.1-nt-CSCtw88763-1.0.zip,
lms3.2.1-win-CSCts95764-0.zip,
lms3.2.1-win-CSCts82530-0.zip
in that order.He added the logs generated by the LMS services Tomcat and Apache
Cisco :: CiscoWorks LMS 3.2 With TACACS Role Authentication?
Jan 4, 2011I'm trying to get user authentication backed off to ACS 5.1, I've got it working but not the way I'd like. This is using the TACACS settings not ACS mode.I've created a local user in CW and assigned it to the correct roles, then created a user in ACS with the same name and a different password and this works fine.My question is can I set the roles on the TACACS server using a shell profile/custom attributes. All the documentation I can find is for ACS v4?
View 15 Replies View RelatedCisco :: LMS 3.2 / Ciscoworks RME Syslog Automation Actions
Nov 20, 2011I set up RME several years ago on our Ciscoworks several running LMS 3.2 to notify us on any BGP flaps via email notification.I noticed the last couple maintenance period where we had perform Circuit work with our ISP's. We haven't received any emails....I verified those routers are configured to send notifications in the Device Selector and even checked the router logs.
004161: Nov 20 05:04:52 EST: %BGP-5-ADJCHANGE: neighbor X.X.X.X Down BGP Notification sent
004162: Nov 20 05:04:52 EST: %BGP-3-NOTIFICATION: sent to neighbor X.X.X.X 4/0 (hold time expired) 0 bytes
The syslog collector status appears to be normal.....
Cisco :: CiscoWorks LMS 4.0.1 And Remote Syslog Collector
Nov 11, 2012I'm using CiscoWorks LMS 4.0.1 and I need to activate a remote syslog collector.Installation occur without errors and the test subscription is fine but syslog reports are always empty!These two servers need to communicate through a firewall.I'm not able to define a correct rule, a "permit ip any any" does not work also!
View 1 Replies View RelatedCisco :: CiscoWorks LMS 4.0 Fresh Installation On Windows 2008 R2?
Sep 18, 2011I'm installing CiscoWorks LMS 4.0 on a server running Windows 2008 R2 Standard Ed, 64 bit. I'm using the patch to run the setup program. Now I'm upgrading to 4.0.1 without using the patch.
View 1 Replies View RelatedCisco :: Add New Network Elements (me3400 Switch) To CiscoWorks LMS 3.2?
Jan 9, 2013how to add newly installed network elements on our CiscoWorks LMS 3.2.
View 1 Replies View RelatedCisco :: Ciscoworks 3.2 RME Compliance Management With 802.1x Port Configuration
Nov 6, 2011i am currently trying to use LMS 3.2 Compliance management to verify and alter our access port configurations for 802.1x. Below is our current configuration
View 1 Replies View RelatedCisco :: 7606-s / Snmpwalk Gives Timeout Error - Ciscoworks
Sep 17, 2012I used the below syntax to check the snmpwalk to an interface of a cisco 7606-s router from an LMS 4.0 version cli.
NMSROOT/Objects/jt/bin>snmpwalk -v 2c -c <snmp-string> <ip-addr> 1.3.6.1.2.1.31.1.1.1.6
Timeout no response from <ip_address>
This is the error im getting in cli prompt. But i could see that reports are generating.If i try with the loopback ip address, i get proper snmpwalk outputs.. I have increased the timeout and retry options..
Cisco :: LMS Version 3.2.1 / Ciscoworks Inventory Is Not Happening For Controller?
May 29, 2013I added this wlc in lms and tried to collect inventory. But it is failing after taking long hours.(LMS Version 3.2.1,WLC 4404 -Version 7.0.116)(SNMP walk is successful & using SNMP V2c)I hope the specific package is available in LMS as i could find the WLC 4404 in Device update->Sys Obj ID -> <id of 4404 WLC> Any bug could be the reson for this...?
View 6 Replies View RelatedCisco :: 3945 Router Error While Adding In CiscoWorks
May 29, 2010I have a Cisco 3945 Router and when we try to add the same into the Cisco Works it gives me an error saying " CM0056 Config fetch failed for 192.168.xx.xx Cause: CM0204 Could not create DeviceContext for 1238 Cause: CM0206 Could not get the config transport implementation for 192.168.xx.xx Cause: UNKNOWN Action: Check if required device packages are available in RME. Action: Check if protocol is supported by device and required device package is installed.
We are using LMS version 2.6. Any info on the latest router 3945 with support or not.
Cisco :: LMS 4.0 - Service Ciscoworks Daemon Manager Does Not Start
Sep 11, 2011After migrating a virtual machine that hosts the CiscoworksLms 4.0, Daemon Manager service does not start.Following is the error:ERROR! The license file is invalid. Please click this link for information about Obtaining a valid license or purchase click here for current licensing information Otherwise, please contact your Cisco representative for purchasing information.I have already entered in the User casuse group of administrators and reset the password but no use Daemon Manager service not up?
View 1 Replies View RelatedCisco :: LMS 3.2 - How To List Ciscoworks Patches Installed On Server
Dec 10, 2011We have LMS3.2,CS3.3 and RME 4.3.1 on solaris 9 and I want to know what were cisco patches installed on the server in order to install other patches without any problem.
View 1 Replies View RelatedCisco :: Managing Lightweight Access Points In Ciscoworks LMS 4.0?
Jul 25, 2011Is it possible to manage Lightweight Access Points in Ciscoworks LMS 4.0?
View 3 Replies View RelatedCisco :: Ciscoworks LMS 3.2 Configuring To Take Show Tech Support
Jul 17, 2012I am running with LMS 3.2. I have added all the required devices to the LMS and its working fine and taking the backup of Start-up and running configuration as well as vlan information from the devices. My question is that can i configure LMS to take the Show tech-support of all the devices?
View 2 Replies View RelatedCisco :: Ciscoworks LMS 4.0 Link Port Interface Utilization?
Oct 30, 2011I have a problem with System-defined Link Port Interface Utilization Poller. When I generate Interface Utilization Report, this one just displays few Interfaces (see the figure in my attachment). I checked the default poller for interface utilization and recognize that it just associate with few Interface (same as in Interface Utilization Report) instead all. I need to display the utilization of all interfaces in my report
Is Link Port Interface Utilization wrong or Is it necessary to creat user-defined poller that associate with all interfaces of devices?
Cisco :: Copy Running Configuration To Startup - Ciscoworks LMS 4
Mar 21, 2012We were having a discussion in my group about startup vs running configs, and how often some network managers forget to "click save" when they configure a switch. Is there a way to configure Ciscoworks to copy the running config to the startup?
View 2 Replies View RelatedCisco :: CiscoWorks User Tracking Utility LMS Prime 4.2
Nov 2, 2011Does Cisco have any plans to incorporate the CiscoWorks User Tracking Utility into LMS Prime 4.2 or any newer version of LMS? This tool is very useful in identifing where a computer or device is located on a switch. I know SolarWinds just came out with their own version of the User Tracking utility, and I am wondering if Cisco is going to continue on with theirs.
View 1 Replies View RelatedCisco :: High Memory Utilization After Few Days - Ciscoworks LMS 4.0.1
Sep 18, 2011I have the problem that our ciscoworks server gets out of memory after few days. The memory utilization is always getting higher an higher (above 95%). Sometimes it is only after 3 days and sometimes it is after 1 week. So it happens not regularly. I have made an screenshot from the services which use a lot of memory. And at this time the memory utilization is getting higher and higher again....I think there is a problem with tomcat or dbsrv10.exe, there are also a lot of cwjava.exe running.
View 8 Replies View Related
