We have LMS3.2,CS3.3 and RME 4.3.1 on solaris 9 and I want to know what were cisco patches installed on the server in order to install other patches without any problem.
View 1 RepliesI'm installing CiscoWorks LMS 4.0, and upgrade, on a domain member server running Windows 2008 R2 SE 64 bit.
View 1 Replies View RelatedYears ago I installed some patches on my ACS 4.1.x.x and recently I upgraded the system to 4.2.Now on the upgrade status page the old patches are still there, are they still used by the device? What is expected to happen if I remove them?
View 4 Replies View RelatedI want to upgrade the acs 5.1 in distributed system. We have one hub/ primary ACS and two other spoke / secodary acs. I have following querry. Will it be possible to upgrad only one Secondary server.>Will updated secondary ACS will able to sych it configuration with primary acs running on older version?Will updated secondary acs will retain the current configuration and authenticate the client.?
View 4 Replies View RelatedIs is possible to find the iLO IP for a server that has no OS installed? I'm not completely sure how iLO works. I believe the person who needed the IP was going to mount an ISO for OS installation via iLO.
View 4 Replies View RelatedTrying to figure this all out. I'm getting untranslated hits. I posted the config I have so far.
Code...
Cisco Adaptive Security Appliance Software Version 8.4(4)1
Device Manager Version 7.0(2)
Hardware: ASA5510, 1024 MB RAM, CPU Pentium 4 Celeron 1600 MHz
#show webvpn anyconnect
1.disk0:/anyconnect-win-3.1.00495-k9.pkg 1 dyn-regex=/Windows NT/
CISCO STC win2k+
3,1,00495
Hostscan Version 3.1.00495
Profile in atthach-file. After this profile is uploaded to client Optimal Gateway Selection doesn't work propertly: When 'vpn1.mydomain.com/mygroup' (it best TTL server) is unreachable, then OGS try to be connected to other servers, but without group-url, for example 'vpn2.mydomain.com' (instead of 'vpn2.mydomain.com/mygroup')
At present we are using the Ciscoworks LMS bunde 3.0. I would like to upgrade to LMS 3.1.
My Question: Is it possible to upgrade to LMS 3.1 with using the existing LMS 3.0 license.
There was a interface down in one of critical devices in the network.that particular log is not captured by the ciscoworks(DFM-alerts).
View 1 Replies View RelatedI am trying to get CiscoWorks LMS 4.0 to connect to my routers in order to back up configurations, but I am getting SSH authentication failures reported in the router logs (and archiving fails).
The credentials LMS is using is a username and password with priviledge 15: the account is established in TACACS+. I can log into the devices directly with this user account.However, I cannot TFTP from the routers to the LMS either (I get a permission denied message in the router).
LMS did manage to fetch some configs, but 90% of my devices are having this issue.
I need download LMS 4.0 eval trial. But i can't see any link down on url...
View 1 Replies View RelatedI upgraded the LMS 4.0 with LMS 4.0.1 but now the events are removed of Fault View. The equipments than I am monitoring are: ME-3600, ME-3800 and ASR 9000. This is a configuration problem or I have to update something else?
View 1 Replies View RelatedI have upgraded our LMS 3.x to the new LMS 4.x Version. have installed the new 4.x on an new server and importet the backup.
I have importet a Certificate and have enabled the Browser-Server Security Mode, Enabled I added some new Netshow Jobs which run every day.
I get the email from the jobs and the URL in the email but, URL
When i click on the link i only get:
Forbidden: You don't have permission to access /rme/NSViewJobResults.do on this server.
Additionally, a 403 Forbidden error was encountered while trying to use an ErrorDocument to handle the request.
i must change the link to Urls there anywhere an option to edit the text which is send with the jobs, to fix the url?
I am running CiscoWorks LMS 4.0.1 since 6 months and I wanted to generate today a report about the interface utilization on 2 Cisco switches (Catalyst 3750G). The corresponding job is created, it runs and then i get "succeeded with info" in the "Run Status" column. When I want to click then on the "View Report" link, I get the following error: "Could not generate the report. Either data is not available for the specified duration or the report job failed."
I tried the same procedure with 2 other switches but I have got the same result.
A while back we were looking into upgrading our SUN/Oracle server to better service our CiscoWorks. Our vendor (partnered Cisco Vendor) told us that Cisco was developing an appliance like WCS and CNR that runs Redhat for CiscoWorks.Does any one have any info on this or could this be a rumor?
We do not run Windows devices on any of our network enterprise and this would be so cool!
Oracle is getting to be a clone of Windows..in our opinion
If this is true, I will happy to sit and wait for it.
We now run LMS 4.0 on a SUN/Oracle T2000 and it seems to be bottlenecking.
How to get Ciscoworks LMS 4.0.1 serial number ? I need that to put the product under mainrtenance, and I can't manage to get it.
View 2 Replies View RelatedI am having LMS 2.5 and nearly 50 cisco 3560 in my network. And I want to configure rcp. How can I do it.
View 1 Replies View Relatedhow to integrate NetFlow to some Ciscoworks module.
View 3 Replies View RelatedWhen trying to start CiscoWorks Daemon Manager i get the following message:"The CiscoWorks Daemon Manager service on local computer started and the stoped. Some services stop automatically if they are not in use by other services or programs."I have tring starting the service from DOS also and get,E:Program FilesCSCOpxsetupsupport>net start crmdmgtdThe CiscoWorks Daemon Manager service is starting.The CiscoWorks Daemon Manager service could not be started. The service did not report an error. More help is available by typing NET HELPMSG 3534.
View 11 Replies View RelatedI am looking for a way to get CiscoWorks LMS 4 to send me an email alert when a switch port goers into a security violation (err-disabled).
View 2 Replies View RelatedI am trying to use Ciscoworks LMS3.2 with RME 4.3.1. to upgrade many, many Cat3750x stacks we have laying around. The problem I am having is that Ciscoworks downloads the new image to the Stack’s master switch only and not to all switches. When I reload the stack after the download, any switch could become the master. I already set up the priority to always have the same master, but the process is unreliable and more than once I ended up with another switch as a master. In any case if the master is not the switch with the new image, the stack will keep the old image as their running image and the switch with the newer image has problems joining the stack (after a while it downgrades and become stable)I know how to do it manually, but I was hoping Ciscoworks would be able to do this for me. It would make my life much easier.
View 1 Replies View RelatedI upgraded CiscoWorks LMS from 3.0 to 3.2 today. Everything worked prior to the upgrade.The upgrade was successful, with no errors, and all services started. check everything and I see no problem. The system creates the file MDCSupportInformation.zip me clean without any content.I add the installation log file;And tell them that after upgrading to 3.2, you carge the following patches:
LMS321-win-CSCtr77570-0.zip,
cm5.2.1-nt-CSCtw88763-1.0.zip,
lms3.2.1-win-CSCts95764-0.zip,
lms3.2.1-win-CSCts82530-0.zip
in that order.He added the logs generated by the LMS services Tomcat and Apache
I'm trying to get user authentication backed off to ACS 5.1, I've got it working but not the way I'd like. This is using the TACACS settings not ACS mode.I've created a local user in CW and assigned it to the correct roles, then created a user in ACS with the same name and a different password and this works fine.My question is can I set the roles on the TACACS server using a shell profile/custom attributes. All the documentation I can find is for ACS v4?
View 15 Replies View RelatedI set up RME several years ago on our Ciscoworks several running LMS 3.2 to notify us on any BGP flaps via email notification.I noticed the last couple maintenance period where we had perform Circuit work with our ISP's. We haven't received any emails....I verified those routers are configured to send notifications in the Device Selector and even checked the router logs.
004161: Nov 20 05:04:52 EST: %BGP-5-ADJCHANGE: neighbor X.X.X.X Down BGP Notification sent
004162: Nov 20 05:04:52 EST: %BGP-3-NOTIFICATION: sent to neighbor X.X.X.X 4/0 (hold time expired) 0 bytes
The syslog collector status appears to be normal.....
I'm using CiscoWorks LMS 4.0.1 and I need to activate a remote syslog collector.Installation occur without errors and the test subscription is fine but syslog reports are always empty!These two servers need to communicate through a firewall.I'm not able to define a correct rule, a "permit ip any any" does not work also!
View 1 Replies View RelatedI'm installing CiscoWorks LMS 4.0 on a server running Windows 2008 R2 Standard Ed, 64 bit. I'm using the patch to run the setup program. Now I'm upgrading to 4.0.1 without using the patch.
View 1 Replies View Relatedhow to add newly installed network elements on our CiscoWorks LMS 3.2.
View 1 Replies View Relatedi am currently trying to use LMS 3.2 Compliance management to verify and alter our access port configurations for 802.1x. Below is our current configuration
View 1 Replies View RelatedI used the below syntax to check the snmpwalk to an interface of a cisco 7606-s router from an LMS 4.0 version cli.
NMSROOT/Objects/jt/bin>snmpwalk -v 2c -c <snmp-string> <ip-addr> 1.3.6.1.2.1.31.1.1.1.6
Timeout no response from <ip_address>
This is the error im getting in cli prompt. But i could see that reports are generating.If i try with the loopback ip address, i get proper snmpwalk outputs.. I have increased the timeout and retry options..
I added this wlc in lms and tried to collect inventory. But it is failing after taking long hours.(LMS Version 3.2.1,WLC 4404 -Version 7.0.116)(SNMP walk is successful & using SNMP V2c)I hope the specific package is available in LMS as i could find the WLC 4404 in Device update->Sys Obj ID -> <id of 4404 WLC> Any bug could be the reson for this...?
View 6 Replies View RelatedI have a Cisco 3945 Router and when we try to add the same into the Cisco Works it gives me an error saying " CM0056 Config fetch failed for 192.168.xx.xx Cause: CM0204 Could not create DeviceContext for 1238 Cause: CM0206 Could not get the config transport implementation for 192.168.xx.xx Cause: UNKNOWN Action: Check if required device packages are available in RME. Action: Check if protocol is supported by device and required device package is installed.
We are using LMS version 2.6. Any info on the latest router 3945 with support or not.
After migrating a virtual machine that hosts the CiscoworksLms 4.0, Daemon Manager service does not start.Following is the error:ERROR! The license file is invalid. Please click this link for information about Obtaining a valid license or purchase click here for current licensing information Otherwise, please contact your Cisco representative for purchasing information.I have already entered in the User casuse group of administrators and reset the password but no use Daemon Manager service not up?
View 1 Replies View RelatedIs it possible to manage Lightweight Access Points in Ciscoworks LMS 4.0?
View 3 Replies View Related