I'm using CiscoWorks LMS 4.0.1 and I need to activate a remote syslog collector.Installation occur without errors and the test subscription is fine but syslog reports are always empty!These two servers need to communicate through a firewall.I'm not able to define a correct rule, a "permit ip any any" does not work also!
View 1 Replies
We have LMS 4.1 in our network. We had recently installed Remote Syslog Collector on a new Server to collect logs from all the devices. How can we integrate the Remote Syslog Collector with the LMS Server?
View 3 Replies View Relatedmy LMS 4.2, syslog collector on LMS doesnt working even service syslog collector running normaly and also i saw in syslog_info is working to collect syslog from all router but not show up in dashboard monitoring.I have setting on every router to logging (ip address LMS) but on LMS no any syslog from router can collect.i did a selftest from LMS there are all PASS except nslookup fail, it is has relation with syslog not show up on dashboard?
View 5 Replies View RelatedIs there an .ISO file for installing on Windows Server20888SR2 ?
View 1 Replies View RelatedI set up RME several years ago on our Ciscoworks several running LMS 3.2 to notify us on any BGP flaps via email notification.I noticed the last couple maintenance period where we had perform Circuit work with our ISP's. We haven't received any emails....I verified those routers are configured to send notifications in the Device Selector and even checked the router logs.
004161: Nov 20 05:04:52 EST: %BGP-5-ADJCHANGE: neighbor X.X.X.X Down BGP Notification sent
004162: Nov 20 05:04:52 EST: %BGP-3-NOTIFICATION: sent to neighbor X.X.X.X 4/0 (hold time expired) 0 bytes
The syslog collector status appears to be normal.....
I have a couple of Cisco 2960's sending syslog messages to a remote syslog-ng on port 514 (standard).
I need to set another Swtich so it sends traffic to the same syslog server but on another UDP port (such as 714),, is that possible,? I cannot find the option on the documentation.
Add the ability to send syslog events to multiple syslog servers in the SA500 Series routers. I know the functionality is currently in the RV220W because we utilized it. It would be great if you could configure the syslog servers by event type as well. For example, being able to send the kernel events to syslog server A, and all other events to syslog server B.
View 0 Replies View RelatedRecently i have upgraded the IOS of ASA5550 (in HA mode) to 8.4.2 from 8.0.5, after OS upgrade we found that the syslog from thses firewalls are not getting captured/transfered to centralised syslog server. The server is reachable from the firewalls.
View 3 Replies View RelatedMy VRF Collector job has started failing. I have attached the contents of the vnmcollector.log file after setting debug level to DEBUG.
View 1 Replies View RelatedI've noticed a problem with log collector on the secondary acs server. It suddenly stopped to collect logs.So, current acs version is 5.1.0.44.3 and all processes were running. During this time, ACS sent a couple of authentication reports in the monitoring system.But they can not be viewed through ACS Monitoring&Report system. The problem was solved by rebooting the server.
View 0 Replies View RelatedUsing Netflow on Cat 6500s with the NAM-2 as the collector?
View 7 Replies View RelatedWe got 2 Cisco ACS 5.2.0.26.10.Primary server as authentication server and log collector.Secondary server as authentication server. Replication is configured. url..."There are some exceptions to this usual setup, which you can handle as described below: If the ACS 5.3 primary server also functions as a log collector in your 5.3 deployment, you should promote any one of the secondary servers as primary server in the deployment. See Promoting a Secondary Server to Primary "
This exception matches with my case. I have to promote my secondary server as primary.I would have :Secondary server as authentication server and log collector.Primary server as authentication server. I think I have to deregister secondary from primary server..According to the guide, I have to upgrade the log collector server. "Step 1: Choose any secondary server to become a log collector:" I dont have another secondary server..
I'm trying to create a LMS 3.2 IPM Collector, but no source devices appears in the wizard.I have the Auto Mode Enable in the Auto Allocation Settings, and in IPM Devices I can see all my devices. ¿
View 2 Replies View RelatedI have three ASA5505, two firewalls connected to central VPN hub. the central inside network is 192.168.0.0/24,Network A is 192.168.1.0/24,Network B is 192.168.2.0/24,In one of this site (central), I have server with NetFlow collector.,I will collect the traffic information from all ASA at the my one serverCan I configure source IP address (or source interface - inside) for NetFlow packet, originate from ASA? (for example from site A)If it is not possible I think, I can rewrite my access lists and permit udp traffic from outside interface to server IP like this:access-list VPNACL permit udp host <Outside IP site A> host <Inside IP the Server> eq 9996,But I do not understand, what port I must be use in access list on Central site ASA. ,access-list VPNACL_A permit udp host <Inside IP the Server> host <Outside IP site A> eq 9996 ? or, in this place, must be source port in the udp netflow packet?
View 2 Replies View RelatedCan ASA 5510 be configured as bridge mode and still send Netflow info to a collector?ie have a PIX connect internal network to internet. Because PIX does not support NetFlow, as a temporary solution, we were thinking of putting an ASA 5510 between the PIX and internet gateway, and configure it as a bridge so that there will be no routing issues, and the ASA can still send Netflow info to a collector.
View 2 Replies View RelatedCan ASA 5510 be configured as bridge mode and still send Netflow info to a collector?We have a PIX connect internal network to internet. Because PIX does not support NetFlow, as a temporary solution, we were thinking of putting an ASA 5510 between the PIX and internet gateway, and configure it as a bridge so that there will be no routing issues, and the ASA can still send Netflow info to a collector.
View 1 Replies View RelatedAt present we are using the Ciscoworks LMS bunde 3.0. I would like to upgrade to LMS 3.1.
My Question: Is it possible to upgrade to LMS 3.1 with using the existing LMS 3.0 license.
There was a interface down in one of critical devices in the network.that particular log is not captured by the ciscoworks(DFM-alerts).
View 1 Replies View RelatedI am trying to get CiscoWorks LMS 4.0 to connect to my routers in order to back up configurations, but I am getting SSH authentication failures reported in the router logs (and archiving fails).
The credentials LMS is using is a username and password with priviledge 15: the account is established in TACACS+. I can log into the devices directly with this user account.However, I cannot TFTP from the routers to the LMS either (I get a permission denied message in the router).
LMS did manage to fetch some configs, but 90% of my devices are having this issue.
I need download LMS 4.0 eval trial. But i can't see any link down on url...
View 1 Replies View RelatedI upgraded the LMS 4.0 with LMS 4.0.1 but now the events are removed of Fault View. The equipments than I am monitoring are: ME-3600, ME-3800 and ASR 9000. This is a configuration problem or I have to update something else?
View 1 Replies View RelatedI have upgraded our LMS 3.x to the new LMS 4.x Version. have installed the new 4.x on an new server and importet the backup.
I have importet a Certificate and have enabled the Browser-Server Security Mode, Enabled I added some new Netshow Jobs which run every day.
I get the email from the jobs and the URL in the email but, URL
When i click on the link i only get:
Forbidden: You don't have permission to access /rme/NSViewJobResults.do on this server.
Additionally, a 403 Forbidden error was encountered while trying to use an ErrorDocument to handle the request.
i must change the link to Urls there anywhere an option to edit the text which is send with the jobs, to fix the url?
I am running CiscoWorks LMS 4.0.1 since 6 months and I wanted to generate today a report about the interface utilization on 2 Cisco switches (Catalyst 3750G). The corresponding job is created, it runs and then i get "succeeded with info" in the "Run Status" column. When I want to click then on the "View Report" link, I get the following error: "Could not generate the report. Either data is not available for the specified duration or the report job failed."
I tried the same procedure with 2 other switches but I have got the same result.
A while back we were looking into upgrading our SUN/Oracle server to better service our CiscoWorks. Our vendor (partnered Cisco Vendor) told us that Cisco was developing an appliance like WCS and CNR that runs Redhat for CiscoWorks.Does any one have any info on this or could this be a rumor?
We do not run Windows devices on any of our network enterprise and this would be so cool!
Oracle is getting to be a clone of Windows..in our opinion
If this is true, I will happy to sit and wait for it.
We now run LMS 4.0 on a SUN/Oracle T2000 and it seems to be bottlenecking.
How to get Ciscoworks LMS 4.0.1 serial number ? I need that to put the product under mainrtenance, and I can't manage to get it.
View 2 Replies View RelatedI am having LMS 2.5 and nearly 50 cisco 3560 in my network. And I want to configure rcp. How can I do it.
View 1 Replies View Relatedhow to integrate NetFlow to some Ciscoworks module.
View 3 Replies View RelatedWhen trying to start CiscoWorks Daemon Manager i get the following message:"The CiscoWorks Daemon Manager service on local computer started and the stoped. Some services stop automatically if they are not in use by other services or programs."I have tring starting the service from DOS also and get,E:Program FilesCSCOpxsetupsupport>net start crmdmgtdThe CiscoWorks Daemon Manager service is starting.The CiscoWorks Daemon Manager service could not be started. The service did not report an error. More help is available by typing NET HELPMSG 3534.
View 11 Replies View RelatedI am looking for a way to get CiscoWorks LMS 4 to send me an email alert when a switch port goers into a security violation (err-disabled).
View 2 Replies View RelatedI am trying to use Ciscoworks LMS3.2 with RME 4.3.1. to upgrade many, many Cat3750x stacks we have laying around. The problem I am having is that Ciscoworks downloads the new image to the Stack’s master switch only and not to all switches. When I reload the stack after the download, any switch could become the master. I already set up the priority to always have the same master, but the process is unreliable and more than once I ended up with another switch as a master. In any case if the master is not the switch with the new image, the stack will keep the old image as their running image and the switch with the newer image has problems joining the stack (after a while it downgrades and become stable)I know how to do it manually, but I was hoping Ciscoworks would be able to do this for me. It would make my life much easier.
View 1 Replies View RelatedI upgraded CiscoWorks LMS from 3.0 to 3.2 today. Everything worked prior to the upgrade.The upgrade was successful, with no errors, and all services started. check everything and I see no problem. The system creates the file MDCSupportInformation.zip me clean without any content.I add the installation log file;And tell them that after upgrading to 3.2, you carge the following patches:
LMS321-win-CSCtr77570-0.zip,
cm5.2.1-nt-CSCtw88763-1.0.zip,
lms3.2.1-win-CSCts95764-0.zip,
lms3.2.1-win-CSCts82530-0.zip
in that order.He added the logs generated by the LMS services Tomcat and Apache
I'm trying to get user authentication backed off to ACS 5.1, I've got it working but not the way I'd like. This is using the TACACS settings not ACS mode.I've created a local user in CW and assigned it to the correct roles, then created a user in ACS with the same name and a different password and this works fine.My question is can I set the roles on the TACACS server using a shell profile/custom attributes. All the documentation I can find is for ACS v4?
View 15 Replies View RelatedI'm installing CiscoWorks LMS 4.0 on a server running Windows 2008 R2 Standard Ed, 64 bit. I'm using the patch to run the setup program. Now I'm upgrading to 4.0.1 without using the patch.
View 1 Replies View Related
