I have some lags on my 3945 router. From show ip nat statistics there is following output:
BR1#show ip nat statistics
Total active translations: 20 (0 static, 20 dynamic; 20 extended)
Peak translations: 8877, occurred 1w0d ago
Outside interfaces:
GigabitEthernet0/0, GigabitEthernet0/1
[code].....
I have this details 196.14 230.72/ 30. What is the IP, Subnet and gateway from this details
View 1 Replies View RelatedI change only a chasis in a router 3845, but the "show version" command should be the same , except for the serial number and other parameter of time.. however, the number of serial interface change from 4 up to 2.The hardware module of 3845 are 3.
1.- VWIC E1/T1 with 2 port
2.- Fastethernet 36 port
3.- Supervisor engine with 2 Gigabit port
I am trying to find out what the 'normal' operating temperature of the CPU in a 3945 router is? We have just replaced some 2800 routers for 3945's and the NMS server initially complained about the new router CPU temperature being too high. Compared to the 2800 the CPU temperature is much hotter - 50 degrees celcius as opposed to 20-smothing degrees. I have searched but can't find what are considered 'normal'?
This is the output:
router#sho environment allSYSTEM POWER SUPPLY STATUS==========================Internal Power Supply 1 Type: DCInternal Power Supply 1 12V Output Status: Normal
[Code].....
I need to upgrade a router from a 2811 to a 3945.
2811 has the following modules:
Is Cisco 3945 router support URL based filtering . For example to block website [URL] but not the main site [URL].
View 1 Replies View RelatedI reported a really strange issue on a Cisco Router 3945. Here below info about release software used: [code] Please look at a brief extract of router running configuration file: [code] It’s an easy configuration of Extended ACL and the application on an Ethernet interface. The expected result is:
- The interface works properly (because access list is permitting every kind of data traffic in input)
- Checking “show access-list 180”, the counter of matched packets increments for all the packets that are forwarded inside the fa0/0/1.
But actually the Fastethernet 0/0/1 drops all the packets as if all the packets don’t match with access list (And this behavior is really incredible). The interface couldn't be used anymore because any kind of data traffic is denied.
3945 Router IOS Required for support VoFR Feature
View 1 Replies View RelatedI just got my first 3945 router and E3/T3 Network cards and when I do a sho ver I can see the E3/T3 card but when I do a show run all I see are the 3 GE interfaces.
View 1 Replies View RelatedI am getting the following message from a 3945 router: %CERM-4-TX_BW_LIMIT: Maximum Tx Bandwidth limit of 85000 Kbps reached for Crypto functionality with securityk9 technology package license.
That router has 8 Gre/IPsec tunnels and one of those tunnels is 100Mbps.The question is, could I get 100Mbps as the sum of all tunnels, or is there a restriction to 85Mbps ??
When I try to configure a voice port (like voice-port 0/0/0:15) after doing a conf t, it gives me an error of invalid input detected.We are using a Cisco 3945. We have successfully setup 3825 and 2851 in the past.
View 2 Replies View RelatedI have a Cisco 3945 Router and when we try to add the same into the Cisco Works it gives me an error saying " CM0056 Config fetch failed for 192.168.xx.xx Cause: CM0204 Could not create DeviceContext for 1238 Cause: CM0206 Could not get the config transport implementation for 192.168.xx.xx Cause: UNKNOWN Action: Check if required device packages are available in RME. Action: Check if protocol is supported by device and required device package is installed.
We are using LMS version 2.6. Any info on the latest router 3945 with support or not.
On a 3945 voicegateway,I want to remove a wave file (announcement), with the purpose that a new one can be automaticaly downloaden from UCCE to the box.Is there a way to do that automaticaly with SNMPSET <voicegateway> <MIB OID> <??wave file name??> <reload>
EDIT: or clear the cache, which it should be I think. (all wave file cache, or only one file, not sure what should be used and/or what is possible
the router IPSec VPN config for remote users using Cisco VPN Client 5.0.07
Router 3945 IOS C3900-UNIVERSALK9-M Version 15.1(4)M4
Here is VPN related config part and log from router and client.
aaa new-model
!
!
aaa authentication login default none
aaa authorization network default none
!
!
crypto isakmp policy 5
encr aes 256
authentication pre-share
[Code]...
I highlighted strings with possible problems of of unabling to connect but doesn't know what to do with it.
I have been assigned the task of configuring a 3945 router for sip circuit. [code] Where am I supposed to put this config? On the bonded serial link?
View 2 Replies View RelatedWe just recently purchased a 3945 ISR G2 router and have a SRE-910 module (with two hard drives) configured in a Raid 1. We are running a stand-alone version of ESXi on the service module and I'm trying to figure out how to monitor the status of the Raid on the drives (along with other health issues). SNMP has revealed nothing so far and even opening a support case for which MIB's to use has proved fruitless. All the documents I find on monitoring the modules say to use LMS which is now Cisco Prime. I've downloaded the trial copy, put in the SNMP settings and scanned the router. I get device results and it shows that I have the SRE-910 module installed, but I get no other configuration / device informaiton from the module itself.
I tried to create a new Monitoring template using the NAM health as the base template (which I'm assuming this is the correct template). Unfortunately, when I actually try to deploy the template against the discovered router, I get an 'Unexpected end of list' error which makes me assume I'm still doing something wrong.
I understand that the password has to be changed the first time we login to Cisco 3945 router but i failed to do that and its not allowing me to connect using default username/password.
View 7 Replies View RelatedWe have Cisco 3945 Router and generating crashinfo while firing PRI from this Router.
View 1 Replies View RelatedRecently, I have increase to 4G memory ram to the router 3945 but when I show version, it does not state there are 4G in there but still showing the old mem ram size. Why is that so ?
View 3 Replies View RelatedCISCO 3945 Routers - Are the 3945 Router power supplies load balanced by default? We are trying to determine if our switch/server rack at our remote location has maxed out it's power load requirements. I just need to know if the 3945 power supplies load balance by default or if the redundant power supply is ON but not really providing the router with power and is just there incase the other power supply fails .
View 3 Replies View RelatedWe have installed a VWIC3-2MFT card on a Cisco 3945 voice gateway but the router doesnt detect the card. out put is as below;
Router Version
============
System image file is "flash0:c3900-universalk9-mz.SPA.150-1.M.bin"
Cisco CISCO3945-CHASSIS (revision 1.0) with C3900-SPE150/K9 with 980992K/67584K bytes of memory.
[Code]....
We are having problems with a two router 3945 in HSRP and a switch 2960.The two routers are connected to the switch 2960 through differentes ports. The problem is that we loose connection between the router and the switch.When we excute the command: show cdp neighbor at router, it shows nothing.If we try to make ping to the 2960 switch it is no reachable.If we make ping to the other router 3945 it is not reachable.All other function of the router are o.k.We are attaching the IOS of the routers and switch 2960 and a document in which make reference to a BUG in which mention about arp overwrite due arp attack which produce DoS.
View 2 Replies View RelatedI am using DHCP/TFTP to autoconfigure a 3945 router. The router properly obtains an IP address and finds the correct TFTP server. The issue lies in the download of the configuration file from the TFTP server. The router downloads the file, gives the "Ok" message, and prompts you to press Return to get started. When I view the running-config, several commands are missing from the Serial 0/0/0 section (HWIC-2T). If I modify the config file on the TFTP server to use Serial 0/0/1 instead and repeat the process, the configuration file loads without any issues and Serial 0/0/1 has all of the commands.
I also tried moving syntax around in my config file, but the end result is still the same. If I use Serial0/0/0 - I don't get all of the commands. If I use Serial 0/0/1, I do.
Application is that need to configure the VOIP with the existing Frame relay network ,where VOFR command is not shown in the router when type yhe command router config#dial-peer voice 123 need vofr On the 3945 router where in the router it is not accepting the above command,
View 8 Replies View RelatedI have cisco 887M-K9 router and I can see output drops are increasing on ATM interface. [code]
View 9 Replies View RelatedHow do I best add one or two additional wireless output ports to a fully used four port wired router?
View 3 Replies View RelatedOn my D-link routher the power supply broke. I instal another one but it has 2.5A as output instead of 2A as the broken one has. Is it dangerous.
View 2 Replies View RelatedI am not able to configure Service policy output command in Cisco 2921 router.While configuring I am getting below error.Same config is working fine in Cisco 3845 router.I am suspectting the problem with license in IOS.
View 3 Replies View Relatedwhat's the meaning of the output:
Interface Speed Local pair Pair length Remote pair Pair status
--------- ----- ---------- ------------------ ----------- --------------------
Gi0/40 100M Pair A 2 +/- 4 meters Pair A Normal
Pair B 2 +/- 4 meters Pair B Normal
Pair C 2 +/- 4 meters Pair C Short
Pair D 2 +/- 4 meters Pair D Short
From the command
test cable-diagnostics tdr int gi 0/40
It's normal?If not, then. the problem is on the cable or on one of the interfaces?The interface is connected between a fastethenert on a 2811 router and a 3560-48 switch.The cable is a straight through cat 5e cable. (I have changed several cables with same result).
I just upgraded my router from the WRT54GL to the EA6300, and it appears there is less coverage with the new unit. Previously, my neighbor could share my router and now with the EA6300 my phone switches to 4G at the end of the driveway. Has anyone seen any specs which publish to output of the ea6300?
View 3 Replies View Relatedthis router of my girlfriends only works when iplug the dsl modem into the output ports what could possibly cause this. would a firmware upgrade straighten it out...
View 1 Replies View RelatedWe have recentrly replaced a 1700 router with Cisco 3945 router (Core Router) and the Channalised E1 interface is configured as given below: [code]
The issue happens intermittenly and makes network not reahable.Status of the links are UP/UP - No traffic forwarded through the link (Ser 0/0/0:1 and Ser 0/0/0:2) and at the same time not able to ping the local IP Address as well - 10.5.10.1/10.7.10.1.No issue on the Ser 0/0/0:0 link - Working fine.If you replace the new router with the old one all are working fine.
Our company have purchase new cisco 3945 and install SM ES3G-24-P.
Etherswitch already configure and can access service module. But assigned VLAN in a port and and ping the host connected on is RTO from the router.
Do i need to upgrade the IOS of the chassis so that the SM installed be detect as ordinary GE port?