Add A Wireless Output To A 4 Port Wired Router?
Nov 5, 2012How do I best add one or two additional wireless output ports to a fully used four port wired router?
View 3 Replies
ADVERTISEMENT
Linksys Wired Router :: RV042G / Create Service To Forward Public Port 9010 To Internal IP Address With Port 23?
Oct 12, 2012Is it possible to create a service which will forward public port 9010 to an internal IP address with port 23?First of all, I do not like to open the public Telnet port to the inside so I would use another public port and second my ISP does not allow some public ports beneath port 80?
View 1 Replies View RelatedCan Plug A Wireless Router Into A Hard Wired Router Port
Mar 2, 2011can i use one of my hard wired router ports to plug in a wireless router and use them both?
View 1 Replies View RelatedCisco Switching/Routing :: Total Output Drops On Switch Port On 6509E
May 22, 2012What is the cause of having a huge number ( 875349) of total output drops on one of my gigabit utp port gi 2/12 which is connected to Cisco 1841 fa0/0 router by mean of cat5e cable.I did change the cable from cat5e to cat 6 and tried to increase hold queue to 4096 and to tweak wrr queue bandwidth
View 4 Replies View RelatedCisco Switches :: SG500-28P SNMP Query For Individual Port Power Output?
Aug 26, 2012Is there a way to ask the above switch how much power it's supplying to various ports?I've found some stuff in POWER-ETHERNET-MIB, but it's only the main power supply and the up/down status of the various ports.
It looks like what I want is
[URL]
but my SG500 tells me:
snmpwalk -v2c -cpublic serverswitch 1.3.6.1.4.1.9.9.402
CISCO-SMI::ciscoMgmt.402 = No Such Object available on this agent at this OID
Connect 3 Wired Devices To Router With 1 Port
Mar 1, 2013I currently have an old Linksys WRT54G router with 4 ethernet and 1 internet port. I have an old Sprint 660 modem connected to the router for internet access. I am also using 3 of the 4 ethernet ports for wired devices (main PC, NAS drive and Dish Network net access). I have another PC and a printer connected wirelessly to the router.Now, with my modem going bad, CenturyLink has provided a combo modem/router (EQ660DR-F1) to be used in place of my Linksys router/modem, providing wired, wireless and modem capabilities in one.My problem is that the new router/modem has only one ethernet port along with a DSL port. Obviously, I can connect my main PC to the ethernet port, DSL to the modem port and connect my 2nd PC and printer wirelessly as they are now. How I might connect my other 2 wired devices, possibly by a hub, AP or bridge or some other means? Can one of these be connected by wireless to connect the other 2 devices, or do these have to be connected physically by wire?
View 2 Replies View RelatedLinksys Wired Router :: BEFSR41v3 Need To Forward A Port
Feb 12, 2012i Have a router called Linksys BEFSR41v3 i need to port forward a port but it just wont open i loggerd in on my router using 192.168.1.1 after i click applications & gaming started the port on 100 and ended on 100 used ipconfig in cmd to find me ipv4 adres and putted in ip adress box also both protocol are on and i clicked the enabled function also i tried also got a static ip i used canyouseeme.org to cheak if my port is open it still says its not open.
View 9 Replies View RelatedCisco Switching/Routing :: Nexus 7000 - (service Policy Type Queuing Output) On Port-channel?
Jan 24, 2013We are planning to implement the following policy map for egress traffic on an Nexus 7000:
policy-map type queuing dd-1p3q1t-8e-out-10G class type queuing 1p3q1t-8e-out-pq1 priority level 1 shape percent 10 class type queuing 1p3q1t-8e-out-q2 bandwidth remaining percent 5 class type queuing 1p3q1t-8e-out-q3 bandwidth remaining percent 5 class type queuing 1p3q1t-8e-out-q-default bandwidth remaining percent 90
We are using two N7K's to which is one N5K connected through a vPC. From the N5k we use a port-channel with 4 * 10G. Two of this four ports are connected to on N7K and the other two are connected to the other N7K. On the n/K's we are using vPC.
My question now are:
1. Where i have to connect the policy map? To the port-channel or on each physical interface?
2. When i have to connect this policy to the port-channel, how does i have to set the shape percent, when i would like to reserve 10% from the 40G? Does i have to set the shape value to 5% on each N7K because vPC?
Connect Usb Wifi Dongle To Ethernet Port On Wired Router?
Jan 29, 2012I would like to connect my USB WIFI dongle directly to my wired router, this would enable me to have wifi access without having my PC switched on all the time, is this possible and if so what kind of adapter do I need? I think I need USB A Female to Ethernet RJ45 Male Router Adapter.
View 5 Replies View RelatedLinksys Wired Router :: Cascading BEFSR41 V4 -10 Port Forwards
Sep 26, 2012Linksys BEFSR41 4.2 Main router 192.168.2.1, if I cascaded a second Linksys BEFSR41 4.2 LAN to LAN 192.168.2.2 would I be able to port forward on the second router? I need more than 10 port forwards.and if so would I have to set the second router up with the internet provider log in and password like the first router?
View 4 Replies View RelatedLinksys Wired Router :: Can't Ping RV016 On WAN1 Port (external IP)
Feb 1, 2011I am trying to setup an RV016 router to do "1 to 1 NAT". I am starting with setting the external IP address of my RV016 to 10.8.58.219 on the WAN1 port, and LAN IP 10.10.20.254. Simple enough. When I connect my laptop to port1 on the router's LAN side I can ping the router's external AND internal IP addresses fine; But I can not ping from outside when connected through WAN1 port.I am performing a simple local test with an external hub, I put a patch cable from WAN1 port to the hub, another patch cable from port 1 on LAN side to the same hub, and from my laptop to the hub. When I use my laptop's IP address with the internal schema (10.10.20.100 for example) I can ping both WAN1 and LAN IP's; but when I use on my laptop the external IP schema (10.8.58.100 for example) I can not ping it. Therefore is not working when I connect my router to the real network.I went into the web setup pages of the router and dissabled: firewall and basicaly all security "blocks" it has, and leave it open for my testing.
View 1 Replies View RelatedLinksys Wired Router :: BEFSR81 Will Not Save Port Forward Info?
May 17, 2011BEFSR81 will not save port forward info. I am trying to setup port forwarding for xbox (53, 80, 88, 1863, 3074), I click on enable to the far right and then click save at the bottom. It says settings are succeful, will return in 5 seconds. When it returns everything is zeroed out.
View 3 Replies View RelatedLinksys Wired Router :: RV042 WAN2 Port Doesn't Work
Nov 21, 2012Continued from [URL] which appears to have been closed by a moderator with a reference to Cisco small business website, but the registration there doesn't work, all buttons are inactive etc.
I just need to know what to do with this RV042. I have two modems, a cable and an ADSL. Both are configure correctly, in bridge mode. Both work fine when connected to WAN1, but when connected to WAN2 they never go online (dont' get IP address). The connect lights are on but they never go online.
Firmware Version: 1.3.13.02-tm
Linksys Wired Router :: Does RV042 Firewall Support Port Forwarding
Aug 5, 2011I am using an RV042 router/firewall -- firmware v1.3.13.02-tm -- connected to a cable modem.I have one public address (WAN1) assigned by my ISP's DHCP server.All my machines on the LAN have static IPs. (RV042 DHCP Server is disabled.)I have set up port (80) forwarding to 192.168.1.101. The HTTP port forwarding does work if an http client on the LAN sends a request to url...But I cannot get a response if I send a request to url... from a machine on the WAN.I did configure Access Rules to allow http traffic (and then tried to allow *all* traffic) between a single IP on the WAN and 192.168.1.101.
The incoming log table shows a connection is made from the http client on the WAN to the correct http server on the LAN, but there is no resonse from the LAN to the WAN.Is my configuration the problem, or is this feature not supported by the RV042 router?Could my cable modem be blocking outbound traffic?
Linksys Wired Router :: RV042 Port Forwarding And Firewall Rules?
Oct 31, 2011I have a system with a RV042 managing the internet connection.Behind the RV042 I have an e-mail server and a development machine that I access through SSH.My problem is that if I forward port 25 to my internal e-mail server it bypasses the firewall rules.I have an external vires and spam scan host that is the only one I should accept incoming email from - but it seems that whenever you add a portforward then it bypasses the firewall rules.
View 1 Replies View RelatedLinksys Wired Router :: E2500 - Cannot Remotely Access Zoneminder On Port 80
Jan 4, 2012I have a Cisco Linksys E2500 modem and I cannot access Zoneminder which is essentially a Linux Security video DVR software package. It is running on a Ubuntu Linux server.
I have HTTP port 80 forwarded to the the static IP address of the Ubuntu server but I repeatedly get a error indicating that the connection timed out whenever I try to access Zoneminder remotely as in remotely accessing it from a coffee shop.
I have absolutely no problem accessing Zoneminder when I on my home local LAN.
I can access other software from remote locations on port 4369 with a TCP preferred protocol setting. That is, port 4369 is forwarded to another Windows workstation with an assigned static IP address. Absolutely no problems with port forwarding of 4369.
Also, I've tested port 80 on the YouGetSignal website which is used for testing port forwarding. The website indicates that port 80 is closed. But when I test port 4369, the website reports that the port is open. Zoneminder which uses port 80 is fully operational when I test port 80 via YouGetsignal.
My ISP has told me that they do not block any ports including port 80.
Linksys Wired Router :: BEFSX41 Way To Determine Connection Speed On Internet Port
Jul 30, 2011I have a BEFSX41 connected to a Motorola SB6120. I changed my plan for a hgih speed, but did not see it.Had a tech out and we found when direct connected to my computer, I get 50 Mbps. When connected through the router, about 9 Mbps. I swapped cables, but still the same.
Is there any way to determine the connection speed on the Internet port? It seems that it only running at 10, when both the router and modem support 100.
Linksys Wired Router :: BEFSR41 Port Forwarding Save Changes Button Missing?
Apr 19, 2011I have a BEFSR41 ver 4.3 and I upgraded my firmware to 2.00.4.8 from within the router. Had a problem with the flashing power light. Resolved the issue after reading another post on this forum using the TFTP utility. Now, however, if I go into either Port Forwarding or Port Triggering and change anything, there is no Save Changes button to click on in either page. They are missing. If I click away, or close the browser and come back, all changes I made are lost. I have tried reloading the firmware at least four times. I've powered off, pressed the reset button and any combination of these that you can reasonably think of. The buttons are gone! I have tried accessing the router from both IE and Firefox, accessing the router from all the machines on my network, to no avail. Everything was working fine before the upgrade, of course. The router does not have the option to save the old firmware before any upgrades are made. The original firmware has been overwritten so I can't go back to it.
View 2 Replies View RelatedLan Port For Wired Connectivity - Convert To Wifi / Wireless?
Oct 19, 2012I have an equipment which has LAN port for wired connectivity to the computer. I can connect 10 such equipment thru LAN to the computer & display the data of all the equipments on computer screen. This LAN network I wanna convert to Wi-fi/wireless.
View 4 Replies View RelatedLinksys Wired Router :: BEFSR41 - Samsung BD Player Reports HTTP Port Is Disabled
May 12, 2010As the subject says, I've hooked up a Samsung BD player to a BEFSR41 router. The router has the current firmware version. When I run the connection test for the player, the local connection is good but the Internet connection fails and the message is " The HTTP port is disabled."
I've searched high and low for a solution to no avail. I did searches on the forum and couldn't find anything. As a test, I connected the BD player directly to the DSL modem and the Internet connection worked perfectly so it appears that the blockage is within the router.
I've serched through the router setup and have changed most settings to try and find something that would work. Nothing worked so I have returned my setup to its original state.
Linksys Wired Router :: RV042 Comcast Internet To WAN2 Port Doesn't Get An IP Address
Feb 28, 2012I was able to install the RV042 router to my ATT DSL line (WAN1 port-INTERNET) and it gets an external IP address automatically and the Internet works. When I connect my Comcast Internet to WAN2 port INTERNTE/DMZ) it doesn't get an IP address. and the Internet goes down and the WAN2 port ip address says 0.0.0.0.I've tried releasing/ renewing and it still says 0.0.0.0.Everything else is set as the default.
View 1 Replies View RelatedLinksys Wireless Router :: EA6300 With Less Coverage - Increasing Output Strength?
May 12, 2013I just upgraded my router from the WRT54GL to the EA6300, and it appears there is less coverage with the new unit. Previously, my neighbor could share my router and now with the EA6300 my phone switches to 4G at the end of the driveway. Has anyone seen any specs which publish to output of the ea6300?
View 3 Replies View RelatedCisco WAN :: 3945 Router NAT Output Interpretation?
Oct 3, 2012I have some lags on my 3945 router. From show ip nat statistics there is following output:
BR1#show ip nat statistics
Total active translations: 20 (0 static, 20 dynamic; 20 extended)
Peak translations: 8877, occurred 1w0d ago
Outside interfaces:
GigabitEthernet0/0, GigabitEthernet0/1
[code].....
Cisco WAN :: Output Drops On ATM Interface 887 Router
May 14, 2012I have cisco 887M-K9 router and I can see output drops are increasing on ATM interface. [code]
View 9 Replies View RelatedLinksys Wired Router :: EA4500 - Wired Connections Have Long Ping Times
Sep 23, 2012I purchased and set-up the EA4500 on Thursday. Friday my ISP (Charter) was out and worked on connection for over 2 hours due to slowness issues. Connected directly to modem I get normal ping times on whichever computer is connected. When I get the computer connected by the router (hard wired) I get very long ping responses up to 900ms. They are all over the place 30ms (I can live with that), up to the 900's. I contacted Linksys support last night, who had me update to the cloud firmware and change MT U to 1300, have not noticed a difference. I did end up doing a hard reset on the router last night after I lost tech support. We were disconnected with router rebooted, and I didn't have the patience to connect again last night.
It was so slow on my work computer, a pint to yahoo timed out. The computers connecting to router are
XP SP3 (mine)
Win 7 Home (IPV6 turned off)
Work laptop that uses VPN and VOIP
Linksys Wired Router :: E2000 - Security Wired Ethernet Connections
Sep 19, 2011I have an e2000 wireless router and have several devices connected by ethernet cable including private data on an external hard drive. I am planning to allow a tenant in another building connect via an ethernet cable connected to my router. Can I limit that computer (tenant's computer) from accessing all other devices connected by ethernet cable to my router? I know can password protect wireless access and limit access to the internet that way -- but my question is specifically to connections by ethernet cable.
View 1 Replies View RelatedLinksys Wired Router :: E4200 No Longer Accepts Wired Connections?
Oct 11, 2012My E4200 router no longer accepts any WIRED connections. I can connect from the modem to the computer and everything works as expected. I can connect other computers wirelessly to the router. I cannot connect any laptops WIRED to the router. Nothing has changed on the systems to restrict internet access. There is something wrong with the router and the WIRED ports. I tried going through the troubleshooting on this site but it was of little to no assistance. The Cisco Connect utility doesn't appear to accomplish anything either. My guess is because I cannot connect to the WIRED ports on the router to connect to the internet to allow for whatever troubleshooting that needs to be done.
View 2 Replies View RelatedLinksys Wired Router :: BEFSR41 Two Wired Routers In Non-standard Hookup
Sep 14, 2011I have a home network with a wired BEFSR41 that, for a variety of reasons, MUST be manually IP configured (DHCP off). All computers and other devices connected to it are manually IP configured. I desire to add a device that cannot be manually configured, and needs DHCP. I therefore need to daisy-chain two routers with the second one DHCP on (and manual IP connection to the main network). The new device needs two-way internet access, but doesn't care if it sees any other current network devices. I've tried several configurations, none seem to work.
View 3 Replies View RelatedLinksys Wired Router :: BEFSR81 Keeps Losing Wired Connection To WAP54G?
Apr 11, 2012I have a WAP54G in my basement shop, wired to our main router upstairs, which is a Linksys BEFSR81. I'm not sure if this is an issue with the WAP or the router.
I only use the laptop computer in the shop every couple of days, but I leave the laptop plugged in and on most of the time. I used to have the power settings such that it didn't power down completely even after a long time. With that setup, if i didn't use the computer for several days, it would find that the connection to the router had died. The wireless link would report that it had a solid connection, but I couldn't connect to anything. Power cycling the WAP always fixed this.
Recently, I decided to save some wear & tear on the laptop drive, and adjusted the power settings to go to standby after a couple of hours. Now, it seems I can't even go one day without losing my connection.
I am running the latest frimware in the WAP, and the router is version 3.1. I can't check the firmware version on the router at the moment, because the web interface is giving me a blank screen. I know from past experience that I will have to power cycle it to get it to talk to me again.
In any event, it seems like the router connection to the WAP is timing out. I set the router "client lease time" up to 10000 a while back when I first had this problem, but that is clearly not doing the trick.
VoIP With No Wired Ethernet Port Access
Jun 7, 2011I have a VoIP phone that requires connection to a wired Ethernet port. I won't have access to the Ethernet port from my new apartment and need to connect over WiFi accessed by my computer. Is there a way to run the VoIP phone over that connection?
View 1 Replies View RelatedCan't Get Wired PC Online Via Linksys E1000 Ethernet Port
Mar 28, 2011Im trying to get my PC connected online from an ethernet port on my router (linksys E1000) but cant get a conenction.no issues with the wireless connection.
View 7 Replies View RelatedBelkin Routers :: Sub Netting N150 With Each Wired Port
Dec 10, 2012Can any of the wired/wireless routers like the n-150 be sub-netted with each wired port being its own subnet?
View 1 Replies View RelatedLinksys Wired Router :: BEFSR41 - Convert Wired Router To Hub?
Jun 16, 2011I have an old BEFSR41 ver. 2 wired outer that I'd like to use with a motorola modem/router as a hub. Is this doable?
View 2 Replies View Related