Linksys Wired Router :: Can't Ping RV016 On WAN1 Port (external IP)
Feb 1, 2011
I am trying to setup an RV016 router to do "1 to 1 NAT". I am starting with setting the external IP address of my RV016 to 10.8.58.219 on the WAN1 port, and LAN IP 10.10.20.254. Simple enough. When I connect my laptop to port1 on the router's LAN side I can ping the router's external AND internal IP addresses fine; But I can not ping from outside when connected through WAN1 port.I am performing a simple local test with an external hub, I put a patch cable from WAN1 port to the hub, another patch cable from port 1 on LAN side to the same hub, and from my laptop to the hub. When I use my laptop's IP address with the internal schema (10.10.20.100 for example) I can ping both WAN1 and LAN IP's; but when I use on my laptop the external IP schema (10.8.58.100 for example) I can not ping it. Therefore is not working when I connect my router to the real network.I went into the web setup pages of the router and dissabled: firewall and basicaly all security "blocks" it has, and leave it open for my testing.
View 1 Replies
ADVERTISEMENT
Jan 6, 2011
I use Rv016 and config load balance and connect to website [url]... and click Login BANK it can't login and show error page [url].... When I try connect bypass don't use RV016 can connect it. when I try to close firewall service it can't not login again.
View 1 Replies
View Related
Jan 16, 2011
Currently We have an RV016 setup and Setup>Network we have the following settings:
Host Name: pagegateway
Domain Name: mycompany.com
Device IP address: 10.20.181.1
Subnet Mask: 255.255.255.0
DHCP Server is not enabled on the RV016. We currently have a Windows 2003 Server that is acting as Exchange Server, Active Diretory, and DHCP Server. My issue is that we are running out of IP addresses and I have about 20 or so left to assign. Given the above setting can I make changes to my RV016 to give me more than 256 addresses? If yes what do I need to do and do I need to make any changes on Windows Server?
View 1 Replies
View Related
Oct 16, 2012
I have recently implimented an RV016 device into our network. We have a bonded T1 service with Paetec/Windstream (5 static IPs) and also a cable connection with Comcast (no static IP). The T1 has been our primary connection, and our MX and A records all use this IP address. I have the rules set and using a one-to-one NAT setup with our 5 IPs. Everything is working great with the T1 in place and email is flowing with no problems, however when I connect the cable into the WAN2 port and try to send email, its using that outbound connection, rather then the T1 and our spam filter is blocking it. So the email is rejected and we get this message below.
View 1 Replies
View Related
Apr 13, 2011
how to configure Linksys RV016 for two WANs (cable+DSL)? It looks like switching between those two connections not splitting what is set for WAN1 and what is set for WAN2.I set load balancing as- WAN1 (cable) all HTTP up/donw should go there- WAN2 (DSL) GTalk, IMs, SMTP, POP3, IMAP up/down should go therebut looks like is not working that way.When I will go to speedtest.net and test a connection I always get less amount then connected directly through cable : Also when people try to use any session or IP sensitive web site it doesn't let them to log in because session was expired (based on IP) or IP was changed.
View 1 Replies
View Related
Jul 17, 2012
I have hardware version 2 and firmware 3.0.2.01 (latest firmware available for this hardware version I believe) and I cannot get it to email me logs. I have entered my outlook address and our SMTP server.
View 1 Replies
View Related
Dec 10, 2008
We have :DSLT-1 I want to route all VOIP traffic and traffic to one IP address over the T-1, all other traffic I want to route over the DSL. HOWEVER, in the event that the DSL fails, have the DSL traffic failover to the T-1.I have setup the router to do just that (I think) and when I go to a site like "whatismyipaddress.com", it shows my IP as comming from the T-1. With the setup I described that traffic should always route over the DSL.Straight up protocol binding won't work because the traffic I want to route over the T-1 to one specific IP is going to be prot 80 and 443 (web traffic)
View 5 Replies
View Related
Oct 27, 2011
I just configured a RV016 and it's ignoring my VPN connections and its routes. When I run a tracert to my other site it returns all the hops between they.
View 1 Replies
View Related
Aug 8, 2011
My RV016 does not seem to route traffic that does not originate from the subent that it sits on. For example, I have my RV016 on 192.168.1.1 and a gateway to 192.168.2.0/24 is at 192.168.1.2. None of the traffic originating in 192.168.2.0 is routed by the RV016. I have checked the routing tables and ACLs with no luck. I know the traffic is hitting the RV016 because I setup a packet sniffer. The packets just simply die there. Is this a limitation of the RV016 only being assigned to a single class C? Does it also ignore all internal traffic not from that class C even if the ACLs are open?
View 1 Replies
View Related
Jun 2, 2011
Currently I have a VPN tunnel setup between our company locations. Location A has Linksys RV016 and Location B has RV082. Everything has been working with no problems for the past 2 years with only minor disconnect issues in the VPN tunnel between the locations.
For the past 2 weeks I have been running into issues with the Tunnel. Users in Location B are reporting problems with losing connection to applications that are hosted in Location A. At first I start with doing a ping to router address in Location B and I get "request timed out". Next I login to router in Location A and under VPN I notice that the VPN tunnel is not disconnect (I see disconnect button). Once I click on Disconnect the screen refreshes and that seemed to restablish connecting with router in Location B. The drop connection has been been going on for the past 2 weeks and only happens once a day specifically between 1 PM and 3 PM EST. I have been reading all over the internet and no luck at all. The VPN tunnel settings are the same on both routers and under Advanced options both Keep Alive and Dead Peer Detection (DPD) are checked.
View 1 Replies
View Related
Jun 22, 2011
I am using a RV016 (192.168.1.2) as a router and DHCP. It automatically assigns its own IP which is 192.168.1.2. I can not set my RV016 to assign a Default Gateway IP of the server. The workstations will connect to internet via this server (192.168.1.1)
View 1 Replies
View Related
Jun 9, 2012
just purchase this RV016 and the firmware has been updated to 3.0.2.01-tm.Every download I try through the router leads to a curruption somehow, even though the download manager gets it all. If I go straight from the cable modem I have no problems.It's a 4mbps upload and 0.8 downlink from what speedtest shows. I have tried diff DL managers, and get the same result on different connected PC's. The great thing about the RV016 is it speeds up the connection on this cable modem.What can I change to get downloads working?
View 1 Replies
View Related
Nov 24, 2011
I have a sonicwall firewall connected to the LAN port of the RV016 router and two DSL modems connected to the WAN ports.
Ip address allocation:
Firewall
192.168.50.9
RV016
LAN - 192.168.50.10
WAN - 192.168.60.1
WAN - 192.168.61.1
What configurations do I need to enter into the RV016 to allow other networks connected to the firewall(192.168.3.0, 192.168.2.0) to access the internet?
View 1 Replies
View Related
Sep 23, 2012
I purchased and set-up the EA4500 on Thursday. Friday my ISP (Charter) was out and worked on connection for over 2 hours due to slowness issues. Connected directly to modem I get normal ping times on whichever computer is connected. When I get the computer connected by the router (hard wired) I get very long ping responses up to 900ms. They are all over the place 30ms (I can live with that), up to the 900's. I contacted Linksys support last night, who had me update to the cloud firmware and change MT U to 1300, have not noticed a difference. I did end up doing a hard reset on the router last night after I lost tech support. We were disconnected with router rebooted, and I didn't have the patience to connect again last night.
It was so slow on my work computer, a pint to yahoo timed out. The computers connecting to router are
XP SP3 (mine)
Win 7 Home (IPV6 turned off)
Work laptop that uses VPN and VOIP
View 5 Replies
View Related
Aug 15, 2011
I'm looking to setup a few ip security cameras in my house and would like to monitor from work. The first thing I did was give the ip camera a static ip on my local LAN 192.168.1.104. I also forwarded port 9000 to this ip. I then went to [URL] to look up my external ip address. I was able to obtain one ip for my router and another for my modem (disconnected router and went direct through modem).
I've since tried to ping my router WAN ip from work numerous times via http://24.x.xxx.xx:9000 and I get timeout errors. I've tried traceroute and it gets close, but times out the last 3 hops. I've had Comcast on the phone many times trying to resolve and needless to say they weren't able to work.
View 6 Replies
View Related
Jan 14, 2013
As a raw test it is handy for us to ping externally the WAN port of the SRP 527W. How we configure the SRP 527W to allow this? FYI we have the inbulit SRP firewall enabled.
View 2 Replies
View Related
Mar 10, 2012
I am converting from a Cisco Model 850 to a RV042, all is well so far but I cannot implement one feature I had on the old router.I want to do one to one nat from one internal ip to one external ip but I only want to use one tcp/ip port.The command to do this on the old cisco 850 was this:"ip nat inside source static tcp 192.168.1.181 80 75.xxx.xxx.181 80 extendable"Can this be done with the RV042?I can do one to one nat but it include all ports.
View 1 Replies
View Related
Oct 12, 2012
Is it possible to create a service which will forward public port 9010 to an internal IP address with port 23?First of all, I do not like to open the public Telnet port to the inside so I would use another public port and second my ISP does not allow some public ports beneath port 80?
View 1 Replies
View Related
Jan 11, 2011
Just replaced my older Cisco router with an E2000 and now none of the connected PCs can ping each other. I have two wired and two wireless nodes on the 192.168.1.X subnet (defaults) using DHCP. All nodes can access the Internet with no problems, but none of them can see each other -- no ping, no Network Neighborhood, nothing. Since this all worked fine before I swapped routers and I've made no changes on any of the nodes, I presume this is something about the router.
I've tried all the usual troubleshooting steps (spent 10 years working as Systems Engineering in IP networking) - no luck. I've also tried various settings of the router (e.g. turned off SPI) but no luck either.
my new router doesn't block connections between attached PCs on the same subnet ....
P.S. One strange observation : using Wireshark I can see the pinging node (.137) ARP for the destination IP (.102), and the ARP reply is sent by the destination node (.102) , but it looks like the Echo Request never makes it to the target machine -- i.e. I think the router is blocking it.
View 9 Replies
View Related
Oct 12, 2011
Loss connection every day for several hours and just comes back. Reset router than works fine. Only about six months old. Found several forums staing the same problem. I have a RV016 16 port VPN router. What can I do?
View 1 Replies
View Related
Apr 30, 2013
I am being told from my remote end I do not have port 22 opened up. I have single port forwarding to SSH 22 and Port Range 22 enabled.
View 1 Replies
View Related
Jan 4, 2011
I am using the default configuration at this point. I just connected 1 computer using the default IP with DHCP on the RV042 router. 192.168.1.0/255.255.255.0.I connect my wildblue satalite modem using a static IP address 75.106.203.xxx / 255.255.252.0 I can ping the RV042 router and the static IP address of the wildblue router but I can't ping the gateway on the wildblue side. Either from the PC or the Router diag tools.
View 1 Replies
View Related
Oct 16, 2011
I have been looking over the manual for my rv016 but cannot find the information I need.
I have 4 external ip addresses that I need to be able to forward to specific internal ips.
A couple of the external addresses will be forwarding with the same ports so just simple port trggering or forwarding will not work.
Can this be accomplished with the rv016 or do I need to look at another device?
View 4 Replies
View Related
Jul 20, 2011
where I can find the OID for enabling and disabling a port for the RV016 router? I performed a snmpwalk but I couldn't find it.
View 1 Replies
View Related
Oct 14, 2012
Problem: IPsec VPN setup seems ok (Client to gateway) but is not responding from client requests. However, remote manage works, PPTP works.
My environment:
Hardware: RV016 10/100 16-Port VPN Router
Firmware: v4.2.1.02 (Jan 18 2012 14:10:55)
Clients: Mac OS X 10.8 (integrated VPN client) , Windows 7 (build in VPN client) OR both with NCP-E VPN client.
None of the above works with IPsec. I have tried all kinds of combinations. I don't think the problem is wether I use Group1 or Group2 or DES or AES...It must be something else... Neither of the built-in VPN (IPsec) clients in Mac OS X or Windows can be configured in an easy way. BUT the NCP-E client can. I have tried to set it up to exactly meet the settings on the server but no progress...How do I setup an IPsec VPN group so that I can use any of my VPN clients to work?
PS. I have also tried the client that comes delivered. 1- It does not work and 2- it's only available for Windows.
View 4 Replies
View Related
Feb 12, 2012
i Have a router called Linksys BEFSR41v3 i need to port forward a port but it just wont open i loggerd in on my router using 192.168.1.1 after i click applications & gaming started the port on 100 and ended on 100 used ipconfig in cmd to find me ipv4 adres and putted in ip adress box also both protocol are on and i clicked the enabled function also i tried also got a static ip i used canyouseeme.org to cheak if my port is open it still says its not open.
View 9 Replies
View Related
Mar 19, 2013
I've had some issues with my 892 router. [code] When match address is set to acl-net12, I can't ping my router on external interface and tunnel is working very bad (15%-20% packet loss).If I change match address from acl-net12 to acl-net12-new then I can ping my router on external interface and vpn si working fine.
I have also an acl (set on external interface) which allow ping but it seems that is not working when acl-net12 is used on crypto map. [code]
View 6 Replies
View Related
Sep 26, 2012
Linksys BEFSR41 4.2 Main router 192.168.2.1, if I cascaded a second Linksys BEFSR41 4.2 LAN to LAN 192.168.2.2 would I be able to port forward on the second router? I need more than 10 port forwards.and if so would I have to set the second router up with the internet provider log in and password like the first router?
View 4 Replies
View Related
May 17, 2011
BEFSR81 will not save port forward info. I am trying to setup port forwarding for xbox (53, 80, 88, 1863, 3074), I click on enable to the far right and then click save at the bottom. It says settings are succeful, will return in 5 seconds. When it returns everything is zeroed out.
View 3 Replies
View Related
Nov 21, 2012
Continued from [URL] which appears to have been closed by a moderator with a reference to Cisco small business website, but the registration there doesn't work, all buttons are inactive etc.
I just need to know what to do with this RV042. I have two modems, a cable and an ADSL. Both are configure correctly, in bridge mode. Both work fine when connected to WAN1, but when connected to WAN2 they never go online (dont' get IP address). The connect lights are on but they never go online.
Firmware Version: 1.3.13.02-tm
View 1 Replies
View Related
Aug 5, 2011
I am using an RV042 router/firewall -- firmware v1.3.13.02-tm -- connected to a cable modem.I have one public address (WAN1) assigned by my ISP's DHCP server.All my machines on the LAN have static IPs. (RV042 DHCP Server is disabled.)I have set up port (80) forwarding to 192.168.1.101. The HTTP port forwarding does work if an http client on the LAN sends a request to url...But I cannot get a response if I send a request to url... from a machine on the WAN.I did configure Access Rules to allow http traffic (and then tried to allow *all* traffic) between a single IP on the WAN and 192.168.1.101.
The incoming log table shows a connection is made from the http client on the WAN to the correct http server on the LAN, but there is no resonse from the LAN to the WAN.Is my configuration the problem, or is this feature not supported by the RV042 router?Could my cable modem be blocking outbound traffic?
View 1 Replies
View Related
Oct 31, 2011
I have a system with a RV042 managing the internet connection.Behind the RV042 I have an e-mail server and a development machine that I access through SSH.My problem is that if I forward port 25 to my internal e-mail server it bypasses the firewall rules.I have an external vires and spam scan host that is the only one I should accept incoming email from - but it seems that whenever you add a portforward then it bypasses the firewall rules.
View 1 Replies
View Related
Jan 4, 2012
I have a Cisco Linksys E2500 modem and I cannot access Zoneminder which is essentially a Linux Security video DVR software package. It is running on a Ubuntu Linux server.
I have HTTP port 80 forwarded to the the static IP address of the Ubuntu server but I repeatedly get a error indicating that the connection timed out whenever I try to access Zoneminder remotely as in remotely accessing it from a coffee shop.
I have absolutely no problem accessing Zoneminder when I on my home local LAN.
I can access other software from remote locations on port 4369 with a TCP preferred protocol setting. That is, port 4369 is forwarded to another Windows workstation with an assigned static IP address. Absolutely no problems with port forwarding of 4369.
Also, I've tested port 80 on the YouGetSignal website which is used for testing port forwarding. The website indicates that port 80 is closed. But when I test port 4369, the website reports that the port is open. Zoneminder which uses port 80 is fully operational when I test port 80 via YouGetsignal.
My ISP has told me that they do not block any ports including port 80.
View 7 Replies
View Related
