Linksys Wired Router :: RV016 Ignoring VPN Connection / Routes?

Oct 27, 2011

I just configured a RV016 and it's ignoring my VPN connections and its routes. When I run a tracert to my other site it returns all the hops between they.

View 1 Replies


ADVERTISEMENT

Linksys Wired Router :: Rv016 Cannot Login A Website

Jan 6, 2011

I use Rv016  and config load balance  and connect to website [url]... and click Login BANK  it can't login and show error page [url].... When I try connect bypass don't use RV016 can connect it. when I try to close firewall service it can't not login again. 

View 1 Replies View Related

Linksys Wired Router :: Expand IP Addresses Beyond 256 / RV016

Jan 16, 2011

Currently We have an RV016 setup and Setup>Network we have the following settings:

Host Name: pagegateway
Domain Name: mycompany.com
Device IP address: 10.20.181.1
Subnet Mask: 255.255.255.0
 
DHCP Server is not enabled on the RV016.  We currently have a Windows 2003 Server that is acting as Exchange Server, Active Diretory, and DHCP Server.  My issue is that we are running out of IP addresses and I have about 20 or so left to assign. Given the above setting can I make changes to my RV016 to give me more than 256 addresses? If yes what do I need to do and do I need to make any changes on Windows Server?

View 1 Replies View Related

Linksys Wired Router :: RV016 Dual Wan Configuration

Oct 16, 2012

I have recently implimented an RV016 device into our network. We have a bonded T1 service with Paetec/Windstream (5 static IPs) and also a cable connection with Comcast (no static IP). The T1 has been our primary connection, and our MX and A records all use this IP address. I have the rules set and using a one-to-one NAT setup with our 5 IPs. Everything is working great with the T1 in place and email is flowing with no problems, however when I connect the cable into the WAN2 port and try to send email, its using that outbound connection, rather then the T1 and our spam filter is blocking it. So the email is rejected and we get this message below.

View 1 Replies View Related

Linksys Wired Router :: How To Configure RV016 For Two WANs

Apr 13, 2011

how to configure Linksys RV016 for two WANs (cable+DSL)? It looks like switching between those two connections not splitting what is set for WAN1 and what is set for WAN2.I set load balancing as- WAN1 (cable) all HTTP up/donw should go there- WAN2 (DSL) GTalk, IMs, SMTP, POP3, IMAP up/down should go therebut looks like is not working that way.When I will go to speedtest.net and test a connection I always get less amount then connected directly through cable : Also when people try to use any session or IP sensitive web site it doesn't let them to log in because session was expired (based on IP) or IP was changed.

View 1 Replies View Related

Linksys Wired Router :: RV016 Not Emailing Logs

Jul 17, 2012

I have hardware version 2 and firmware 3.0.2.01 (latest firmware available for this hardware version I believe) and I cannot get it to email me logs.  I have entered my outlook address and our SMTP server.

View 1 Replies View Related

Linksys Wired Router :: RV016 Load Balance Configuration?

Dec 10, 2008

We have :DSLT-1  I want to route all VOIP traffic and traffic to one IP address over the T-1, all other traffic I want to route over the DSL.  HOWEVER, in the event that the DSL fails, have the DSL traffic failover to the T-1.I have setup the router to do just that (I think) and when I go to a site like "whatismyipaddress.com", it shows my IP as comming from the T-1.  With the setup I described that traffic should always route over the DSL.Straight up protocol binding won't work because the traffic I want to route over the T-1 to one specific IP is going to be prot 80 and 443 (web traffic)

View 5 Replies View Related

Linksys Wired Router :: RV016 Limitations And Traffic Routing

Aug 8, 2011

My RV016 does not seem to route traffic that does not originate from the subent that it sits on. For example, I have my RV016 on 192.168.1.1 and a gateway to 192.168.2.0/24 is at 192.168.1.2. None of the traffic originating in 192.168.2.0 is routed by the RV016. I have checked the routing tables and ACLs with no luck. I know the traffic is hitting the RV016 because I setup a packet sniffer. The packets just simply die there. Is this a limitation of the RV016 only being assigned to a single class C? Does it also ignore all internal traffic not from that class C even if the ACLs are open?

View 1 Replies View Related

Linksys Wired Router :: VPN Tunnel Disconnect Between RV016 And RV082

Jun 2, 2011

Currently I have a VPN tunnel setup between our company locations. Location A has Linksys RV016 and Location B has RV082.  Everything has been working with no problems for the past 2 years with only minor disconnect issues in the VPN tunnel between the locations.
 
For the past 2 weeks I have been running into issues with the Tunnel. Users in Location B are reporting problems with losing connection to applications that are hosted in Location A. At first I start with doing a ping to router address in Location B and I get "request timed out". Next I login to router in Location A and under VPN I notice that the VPN tunnel is not disconnect (I see disconnect button). Once I click on Disconnect the screen refreshes and that seemed to restablish connecting with router in Location B. The drop connection has been been going on for the past 2 weeks and only happens once a day specifically between 1 PM and 3 PM EST. I have been reading all over the internet and no luck at all. The VPN tunnel settings are the same on both routers and under Advanced options both Keep Alive and Dead Peer Detection (DPD)  are checked.

View 1 Replies View Related

Linksys Wired Router :: Can't Ping RV016 On WAN1 Port (external IP)

Feb 1, 2011

I am trying to setup an RV016 router to do "1 to 1 NAT". I am starting with setting the external IP address of my RV016 to 10.8.58.219 on the WAN1 port, and LAN IP 10.10.20.254. Simple enough. When I connect my laptop to port1 on the router's LAN side I can ping the router's external AND internal IP addresses fine; But I can not ping from outside when connected through WAN1 port.I am performing a simple local test with an external hub, I put a patch cable from WAN1 port to the hub, another patch cable from port 1 on LAN side to the same hub, and from my laptop to the hub. When I use my laptop's IP address with the internal schema (10.10.20.100 for example) I can ping both WAN1 and LAN IP's; but when I use on my laptop the external IP schema (10.8.58.100 for example) I can not ping it. Therefore is not working when I connect my router to the real network.I went into the web setup pages of the router and dissabled: firewall and basicaly all security "blocks" it has, and leave it open for my testing.

View 1 Replies View Related

Linksys Wired Router :: Can't Set RV016 To Assign A Default Gateway IP Of Server

Jun 22, 2011

I am using a RV016 (192.168.1.2) as a router and DHCP. It automatically assigns its own IP which is 192.168.1.2. I can not set my RV016 to assign a Default Gateway IP of the server. The workstations will connect to internet via this server (192.168.1.1)

View 1 Replies View Related

Linksys Wired Router :: RV016 Working But All Downloads Lead To Corruption

Jun 9, 2012

just purchase this RV016 and the firmware has been updated to 3.0.2.01-tm.Every download I try through the router leads to a curruption somehow, even though the download manager gets it all.  If I go straight from the cable modem I have no problems.It's a 4mbps upload and 0.8 downlink from what speedtest shows.  I have tried diff DL managers, and get the same result on different connected PC's.  The great thing about the RV016 is it speeds up the connection on this cable modem.What can I change to get downloads working?

View 1 Replies View Related

Linksys Wired Router :: RV016 - Allow Other Networks Connected To Firewall To Access Internet?

Nov 24, 2011

I have a sonicwall firewall connected to the LAN port of the RV016 router and two DSL modems connected to the WAN ports.
 
Ip address allocation:

Firewall
192.168.50.9
RV016
LAN  - 192.168.50.10
WAN - 192.168.60.1
WAN - 192.168.61.1
 
What configurations do I need to enter into the RV016 to allow other networks connected to the firewall(192.168.3.0, 192.168.2.0) to access the internet?

View 1 Replies View Related

Linksys Wired Router :: BEFSR81 Keeps Losing Wired Connection To WAP54G?

Apr 11, 2012

I have a WAP54G in my basement shop, wired to our main router upstairs, which is a Linksys BEFSR81.  I'm not sure if this is an issue with the WAP or the router.
 
I only use the laptop computer in the shop every couple of days, but I leave the laptop plugged in and on most of the time.  I used to have the power settings such that it didn't power down completely even after a long time.  With that setup, if i didn't use the computer for several days, it would find that the connection to the router had died.  The wireless link would report that it had a solid connection, but I couldn't connect to anything.  Power cycling the WAP always fixed this.
 
Recently, I decided to save some wear & tear on the laptop drive, and adjusted the power settings to go to standby after a couple of hours.   Now, it seems I can't even go one day without losing my connection.
 
I am running the latest frimware in the WAP, and the router is version 3.1.  I can't check the firmware version on the router at the moment, because the web interface is giving me a blank screen.  I know from past experience that I will have to power cycle it to get it to talk to me again. 
 
In any event, it seems like the router connection to the WAP is timing out.  I set the router "client lease time" up to 10000 a while back when I first had this problem, but that is clearly not doing the trick.

View 3 Replies View Related

Linksys Wired Router :: Lan To Lan Connection With Befsr41v3?

Feb 21, 2012

I posted a time ago here because i cant open my ports  because i have a internet connection that first goes to my router and then to my modem [URL]

View 1 Replies View Related

Linksys Wired Router :: Get IPSec Connection With 2 RVL200?

May 15, 2007

We have a main and branch office, each with an RVL200 . I configured both with static IP's as provided by my ISP, yet when I try to do a test connection on the IPSec screen I just get that it's "waiting for a connection" in the cell third from the left. Both RVL200 's are connected directly to the modem/bridge supplied by both ISP's.

View 5 Replies View Related

Linksys Wired Router :: VOIP Dropping Connection 2-3x Per Day

Feb 13, 2013

I have a strong internet signal with good SNR coming out of my cable modem, then a nice short 3ft cable going to my linksys VOIP router (I think it's a SPA 2102). Whether I have anything downstream plugged in or not, the "phone" light on the VOIP router goes off every once in a while and when I check I find that I've lost both dial tone and Internet - basically everything downstream of the VOIP router. Have tried every variation on configuration you can imagine (feeding just one phone, feeding the entire phone wiring to the house, nothing at all plugged into the phone jack, no computers downstream plugged in, replaced all the cables, ...). I've replaced BOTH the cable modem and the linksys VOIP router and the problem continues. My cable company says my signal is fine. They suggested a signal amplifier but the coax comes straight to the modem, no splitter, and I'm always seeing 6-7dBmV. My phone company says their router must be losing signal upstream and refusing to reconnect, especially now that we've tried replacing their VOIP router with no change. Any chance I got two 'bad' routers in a row? Not sure what they did for setup parameters. I'm not particularly tech-savvy but have read a lot since seeing these issues, have run my own ping and tracert checks and everything seems to be wonderful... but then most of the time everything IS fine. When I have phone it's crystal clear and when I have internet it's nice and fast. I sometimes go 24hrs or so without a drop, but other times I'm resetting 2-3x in a couple of hours. All I do is power off the VOIP router and back on and everything is fine, for a while. After first getting VOIP things were fine for 4-6 weeks.

View 1 Replies View Related

Linksys Wired Router :: BEFSR41 V4 Keeps Dropping Connection

Feb 4, 2013

For a number of months now, our Internet connection in an office of 5 computers, 2 Macs, 3 windows boxes (1 as dell  laptop) has experienced the connection of the Internet dropping off.The timing of the 'drops' is usually in the morning, when the Dell Inspiron M510 either boots up or wakes from sleep. Typically the solution is to turn off the modem, the router and switch, wait a few minutes, then turn the switch, the router, then the modem back on. Our connection via the modem is through AT&T, via a non-static IP addy.Our router is a BEFSR41, v4, with firmware up to date (circa 2006) It's becoming a daily chore now, just about, and is getting to be a bit of a headache on some days. 

View 3 Replies View Related

Linksys Wireless Router :: WRT120N - Get Wired Connection On PC?

Nov 30, 2011

I'm capped out at 12 mbps service through Mediacom.  My PC is directly wired to the WRT120N.  I consistently test in the 11 mbps range.  
 
I have a very unusual issue though.  
 
I can connect my iphone and Xbox wirelessly through my router with no issues on their side.  However, any time I do so, it kills my wired connection on my PC.  I'm not doing huge downloads or P2P or anything like that.  In fact, the speed drops immediately on my PC the moment I connect my phone to the wireless network regardless of what i'm doing on the phone (checking email or loading a webpage).

View 2 Replies View Related

Linksys Wireless Router :: Slow Wired LAN Connection On E1200

Feb 15, 2013

I have an E1200 acting soley as an AP.  Everything works just fine, but when I try to copy files from one wired computer(both Windows 7) to another one on the same router(the E1200 in this case), the network utilization is only about 4%.  If I take one of the computers off its wired connection and make it wireless, the utilization goes up to about 50%.  Also if I take one of the compuyters off this router, and make a wired connection to my main router(which is connected via a wired connection to the E1200), the network utilization goes up to 50%.

View 3 Replies View Related

Linksys Wireless Router :: E1550 Fast On Wired Connection

Apr 2, 2012

I have a Linksys E1550 Wireless Router that is fast as can be on the wired connection, getting 30mbs from the cable modem connection. If I switch to using wireless on the same PC, the max connection speed I'll get is 2mbs. I've changed all sorts of settings trying to get this working right, and it still stays at 2mbs.As an additional note, this router was previously working fine at 30mbs on wireless as well, then out of nowhere this weekend, it started running at 2mbs. I went and purchased another of the same model and it is doing the same thing as well.
 
What is the secret to having this run at it's correct speed, not this slow 2mbs that it is now? I have configured this the same as every other Linksys router I've had in the past, and it is running horribly slow..I'm on the newest firmware as well, have already verified that. The old router was updated to newest firmware as testing to resolve this, and the new router came with it installed already.

View 6 Replies View Related

Linksys Wired Router :: RV082 Slowing Down Internet Connection

Jul 14, 2011

I have a RV082 Linksys router and at the moment it is slowing down my internet connection by a significant amount. With the router, I get about 3 Mbps and with a modem directly connected to my computer I get about 24 Mbps. Before with the router I used to get 15 Mbps, which is understandable because it is connected to 4 computers total. Maybe my setup has something to do with it. I got a cable that is connected to a modem, the modem is connected to the router, from which one port is connected to a computer, and another is used to connect to a Netgear switch, which in turn is connected to 3 more computers.
 
Everything was fine until I went on a trip and wasn't home for about 2 weeks, and when I came back, this happened. I tried restarting the modem, the router and all to no avail. I also tried to do a factory reset on the router and again got slow speeds.

View 1 Replies View Related

Linksys Wired Router :: BEFSR41 V3 And HP 6500a Printer - Keep Loosing Connection?

Apr 6, 2012

have a HP 6500a All In One Printer in the network with a BERSR41 V3 router. I am using a Imac with this sytem for printing and scanning. For some reason I keep loosing the printer when I try to scan? I have it set to a static IP, and can not ping it, but can access the printer throught the network with the HP Utility. Am I missing something in setup on the router that causes it to keep loosing connection?

View 2 Replies View Related

Linksys Wireless Router :: WRT54G Wired Connection Stopped Working?

Jun 24, 2012

I have the WRT54G router for years and use it to provide both a wireless network for our home computers and a wired network for by internet phone that connects me to my office phone system and for my work computer and printer. Last week, the wired network stopped working. I checked the wiring and plugged my wire into all four of the ports in the back of the router with no success.  I followed the troubleshooting procedure that I found and changed the MTU setting.  I tried to update the firmware but the screen seemed to lock up and I was unable to complete the task.

View 9 Replies View Related

Linksys Wireless Router :: Wrt120 Wifi Connection Fine - Wired Is Not

Sep 11, 2012

I have a WRT120 wireless router that works fine, but the wired connection has failed. I have restarted the modem, router and the computer and still doesn't recognize the wired connection.

View 9 Replies View Related

Linksys Wired Router :: Cisco EPC3825 Connection Speed Slows Down To Around 5-7Mt/s

Sep 28, 2011

I'm using Cisco EPC3825 cable modem for my home network, and wondered a thing, that if I set up modem to work in router-mode, my real connection speed slows down to around 5-7Mt/s, when using modem in bridged mode, my connection speed is close to 15-20Mt/s. My serviceprovider provides 200/10M speed to my modem, and they've checked, that modem is working with 204/10M speed, and computers works also, if using modem in bridged-mode.

View 1 Replies View Related

Linksys Wireless Router :: Desktops Dropping Wired Connection To E4200

Jan 2, 2012

I lost all Internet connnecitivity on my Linksys e3000.  After determining that my cable modem was connected and working correctly, I pulled the e3000 and put my old wrv54g router in place.  Wireless worked, but all wired connections showed link but no other apparent connectivity.  Neither of my desktops could get a DHCP lease.
 
At that point, I purchased and manually installed a new e4200 router.  All worked fine.  Both laptops connected via wireless and both desktops via my house LAN.  Until this morning (Monday).  Wireless is working just fine, but both wired computers show 100 Mbs connections on an unknown network with no DHCP.  Checking status shows packets going out, but nothing coming in.  Checking LAN status on the router shows that both ports are connected, but it does not appear to receive anything from either desktop.  All was fine last night.  Oh, the router is on 1.0.03 firmware.
 
I have tried about everything I can think of.  Configurations both on the router and the desktops (one Windows XP, 64 bit and one Windows 7) and all seems fine.  I have disabled and reenabled the network connectors, rebooted both the router and the computers, etc.  Nothing seems to work.

View 5 Replies View Related

Linksys Wireless Router :: EA4500 IMac Wired Slow Connection

Jul 3, 2012

I have a problem with my new router. I connected't my iMac (27" 2010) and NAS Synology 1511. My problem is the slow connection between mac and router - only 100Mbit (ethernet port on mac is 1Gbit), strange thing... my NAS have 1Gbit with no problem, and the mac is not. I trying manual configure - forcing speed to 1Gbit, but then is no connection at all. I'm also trying changing wires, but no change. Im buying special ethernet cable cat 6 - also no change. Changing ports on router - result the same.

View 7 Replies View Related

Linksys Wired Router :: Befsr41v3 Cannot Open Ports Due To Internet Connection

Nov 16, 2011

i cant open my ports  because i have a internet connection that first goes to my router and then to my modem.

View 3 Replies View Related

Linksys Wireless Router :: E4200 - Disable Wi-Fi Totally And Use Wired Connection?

Sep 6, 2011

Can we disable wireless totally in E4200 and just use wired connections? I didn't see any configuration for that, but just in case I missed it. I'm also aware we can disable SSID Broadcast.

View 1 Replies View Related

Linksys Wireless Router :: Can WRT54GL Pass 50mb Through To The Computer On Wired Connection?

Apr 12, 2013

In our area Comcast has increased the internet speed to 50mb.  I have a six year old WRT54GL.  Can this router pass 50mb through to the computer on a wired connection?

View 5 Replies View Related

Linksys Wireless Router :: EA 3500 Dropping Wired Connection When Online Gaming?

Mar 30, 2013

I  just had Comcast setup my internet and it is really fast. 30 down, 10 up, 40 ping, my connection to my computer (wireless) is very fast and my online gaming (wired) is not laggy at all.The problem lies with the connection dropping when I am online gaming. I connected directly to the modem and there's no problem at all. I connect to my Linksys EA3500 and once I start playing in an online game, I disconnect from Xbox Live and am dropped from the game... anywhere from right away until about 10-15 minutes into the game. This is  the only time where my connection falters at all, otherwise it is great. But I play online a lot, and competitively, so I obviously need a stable connection.I have not had this issue with my previous ISP in New York, Time Warner and that connection was much worse. I'm thinking it must be a setting on the router that is causing this, but I can't pinpoint what. I tried automatic AND static connections from my xbox to the router. On the static connection, I even put a DMZ on it, but to no avail.

View 9 Replies View Related

Linksys Wired Router :: CISCO RV082 Slow Internet Connection With Firewall?

Nov 14, 2012

I'm owner of Cisco RV082 router and I have a problem with firewall setup.I would like to deny internet access on port 80 (all sites) for group of users, and allow them internet access for one site by HTTPS (443)After applying rules internet connection is really slow.. Users have to wait something like a 30 sec for a website..I descovered that the reason for slow internet connection is DENY rule. After disbling DENY rule everything works fine..Now I have a few rules added to firewall:

Priority:1 Action: Deny Service: HTTP(80) Source interface: LAN Source:10.82.0.51-10.82.0.245 Destination: Any

Priority:2 Action: Allow Service: HTTPS(443) Source interface: LAN Source: 10.82.0.51-10.82.0.245 Destination: 80.64.59.42
 
What's wrong with those firewall settings?

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved