Linksys Wired Router :: VPN Tunnel Disconnect Between RV016 And RV082
Jun 2, 2011
Currently I have a VPN tunnel setup between our company locations. Location A has Linksys RV016 and Location B has RV082. Everything has been working with no problems for the past 2 years with only minor disconnect issues in the VPN tunnel between the locations.
For the past 2 weeks I have been running into issues with the Tunnel. Users in Location B are reporting problems with losing connection to applications that are hosted in Location A. At first I start with doing a ping to router address in Location B and I get "request timed out". Next I login to router in Location A and under VPN I notice that the VPN tunnel is not disconnect (I see disconnect button). Once I click on Disconnect the screen refreshes and that seemed to restablish connecting with router in Location B. The drop connection has been been going on for the past 2 weeks and only happens once a day specifically between 1 PM and 3 PM EST. I have been reading all over the internet and no luck at all. The VPN tunnel settings are the same on both routers and under Advanced options both Keep Alive and Dead Peer Detection (DPD) are checked.
View 1 Replies
ADVERTISEMENT
Feb 23, 2011
I'm trying to setup a VPN Tunnel between RV082 and WRV200.The RV082 has an static IP, the WRV200 has a dynamic IP. I have to Dyndns.org in the WRV200.I have setup the RV082 tunel auth like: Dynamic IP + email.In the WRV200 I setup the hostname with the username, and the domain with the domain part of domain entered in the RV082.In the RV082 VPN Log I got: Initial Aggressive Mode message from 11.22.33.44 but no (wildcard) connection has been configured.It seems to be working the IPSEC setup but the RV082 does not accept the connection because of a missmatch in the Remote Security Gateway Type parameter in the RV082.
View 1 Replies
View Related
Jun 1, 2011
VPN tunnel backup is not available on the RV016 firmware version 4.0.2.08 (it IS on the RV082. The data sheet and the manual for the RV016 is wrong. I have purchased several RV016 hardware V3 and several RV082 hardware V3. Both have the same current firmware version. We have noted that the RV016 does not have the VPN tunnel failover option found in the RV082. It also does not have split DNS (noted in the manual. A I would have thought that the firmware would provide equal options on the RV042, RV082, and RV016.
View 2 Replies
View Related
Jan 6, 2011
I use Rv016 and config load balance and connect to website [url]... and click Login BANK it can't login and show error page [url].... When I try connect bypass don't use RV016 can connect it. when I try to close firewall service it can't not login again.
View 1 Replies
View Related
Jan 16, 2011
Currently We have an RV016 setup and Setup>Network we have the following settings:
Host Name: pagegateway
Domain Name: mycompany.com
Device IP address: 10.20.181.1
Subnet Mask: 255.255.255.0
DHCP Server is not enabled on the RV016. We currently have a Windows 2003 Server that is acting as Exchange Server, Active Diretory, and DHCP Server. My issue is that we are running out of IP addresses and I have about 20 or so left to assign. Given the above setting can I make changes to my RV016 to give me more than 256 addresses? If yes what do I need to do and do I need to make any changes on Windows Server?
View 1 Replies
View Related
Oct 16, 2012
I have recently implimented an RV016 device into our network. We have a bonded T1 service with Paetec/Windstream (5 static IPs) and also a cable connection with Comcast (no static IP). The T1 has been our primary connection, and our MX and A records all use this IP address. I have the rules set and using a one-to-one NAT setup with our 5 IPs. Everything is working great with the T1 in place and email is flowing with no problems, however when I connect the cable into the WAN2 port and try to send email, its using that outbound connection, rather then the T1 and our spam filter is blocking it. So the email is rejected and we get this message below.
View 1 Replies
View Related
Apr 13, 2011
how to configure Linksys RV016 for two WANs (cable+DSL)? It looks like switching between those two connections not splitting what is set for WAN1 and what is set for WAN2.I set load balancing as- WAN1 (cable) all HTTP up/donw should go there- WAN2 (DSL) GTalk, IMs, SMTP, POP3, IMAP up/down should go therebut looks like is not working that way.When I will go to speedtest.net and test a connection I always get less amount then connected directly through cable : Also when people try to use any session or IP sensitive web site it doesn't let them to log in because session was expired (based on IP) or IP was changed.
View 1 Replies
View Related
Jul 17, 2012
I have hardware version 2 and firmware 3.0.2.01 (latest firmware available for this hardware version I believe) and I cannot get it to email me logs. I have entered my outlook address and our SMTP server.
View 1 Replies
View Related
Dec 10, 2008
We have :DSLT-1 I want to route all VOIP traffic and traffic to one IP address over the T-1, all other traffic I want to route over the DSL. HOWEVER, in the event that the DSL fails, have the DSL traffic failover to the T-1.I have setup the router to do just that (I think) and when I go to a site like "whatismyipaddress.com", it shows my IP as comming from the T-1. With the setup I described that traffic should always route over the DSL.Straight up protocol binding won't work because the traffic I want to route over the T-1 to one specific IP is going to be prot 80 and 443 (web traffic)
View 5 Replies
View Related
Oct 27, 2011
I just configured a RV016 and it's ignoring my VPN connections and its routes. When I run a tracert to my other site it returns all the hops between they.
View 1 Replies
View Related
Aug 8, 2011
My RV016 does not seem to route traffic that does not originate from the subent that it sits on. For example, I have my RV016 on 192.168.1.1 and a gateway to 192.168.2.0/24 is at 192.168.1.2. None of the traffic originating in 192.168.2.0 is routed by the RV016. I have checked the routing tables and ACLs with no luck. I know the traffic is hitting the RV016 because I setup a packet sniffer. The packets just simply die there. Is this a limitation of the RV016 only being assigned to a single class C? Does it also ignore all internal traffic not from that class C even if the ACLs are open?
View 1 Replies
View Related
Feb 1, 2011
I am trying to setup an RV016 router to do "1 to 1 NAT". I am starting with setting the external IP address of my RV016 to 10.8.58.219 on the WAN1 port, and LAN IP 10.10.20.254. Simple enough. When I connect my laptop to port1 on the router's LAN side I can ping the router's external AND internal IP addresses fine; But I can not ping from outside when connected through WAN1 port.I am performing a simple local test with an external hub, I put a patch cable from WAN1 port to the hub, another patch cable from port 1 on LAN side to the same hub, and from my laptop to the hub. When I use my laptop's IP address with the internal schema (10.10.20.100 for example) I can ping both WAN1 and LAN IP's; but when I use on my laptop the external IP schema (10.8.58.100 for example) I can not ping it. Therefore is not working when I connect my router to the real network.I went into the web setup pages of the router and dissabled: firewall and basicaly all security "blocks" it has, and leave it open for my testing.
View 1 Replies
View Related
Jun 22, 2011
I am using a RV016 (192.168.1.2) as a router and DHCP. It automatically assigns its own IP which is 192.168.1.2. I can not set my RV016 to assign a Default Gateway IP of the server. The workstations will connect to internet via this server (192.168.1.1)
View 1 Replies
View Related
Jun 9, 2012
just purchase this RV016 and the firmware has been updated to 3.0.2.01-tm.Every download I try through the router leads to a curruption somehow, even though the download manager gets it all. If I go straight from the cable modem I have no problems.It's a 4mbps upload and 0.8 downlink from what speedtest shows. I have tried diff DL managers, and get the same result on different connected PC's. The great thing about the RV016 is it speeds up the connection on this cable modem.What can I change to get downloads working?
View 1 Replies
View Related
Nov 24, 2011
I have a sonicwall firewall connected to the LAN port of the RV016 router and two DSL modems connected to the WAN ports.
Ip address allocation:
Firewall
192.168.50.9
RV016
LAN - 192.168.50.10
WAN - 192.168.60.1
WAN - 192.168.61.1
What configurations do I need to enter into the RV016 to allow other networks connected to the firewall(192.168.3.0, 192.168.2.0) to access the internet?
View 1 Replies
View Related
Apr 4, 2011
I got problem with RVL200, it works good on my botch mac's witch OSX 10.5,10.6 and Firefox 3.6 but stops working after last java update. The machine switch 10.5 is working because I don't update Java but the other computer is up-to-date.
Problem is with launching the Java applet ,all the rest is working.- I'm log in to SSL VPN Tunnel- The new window is opening I accept applet to run .It try but nothing happens the window is blank with no connect / disconnect buttons.
All I have is Java error:Plug-In Java 1.6.0_24JRE version 1.6.0_24-b07-334-10M3326 Java HotSpot(TM) 64-Bit Server VMjava.lang.SecurityException: [code]....
View 1 Replies
View Related
May 15, 2009
I am trying to set up a dual WAN on my RV082 - I have Verizon DSL on WAN1 and I am trying to establish Time Warner Road Runner on WAN2 as a backup in case DSL goes out on WAN1.I cannot get the router to recognize both connections at the same time. I have power cycled everything, the router is only picking up one internet signal at a time.
View 3 Replies
View Related
Nov 10, 2011
How can I make a device or an IP go through a certain WAN? Basically I want to make the PC I use on the network go through WAN2, I have tried everything but I am really stumped on how to do this, my Firmware Version: v4.0.2.08-tm
View 1 Replies
View Related
Mar 15, 2012
I am using RV082 V3 router. After a reset of the router I have access via both LAN and WAN for some period of time (not yet known) later that day or the next day when I try to access it via the WAN it sits on "opening page" for a while eventually coming up with the login box. After logining in the page only partially loads. (All the settings are shown, but the proper selections are not made.) Internet explorer will then show something like "8 items remaining" in the status bar. If I close and re-open IE I am unable to connect at all. At this point I also cannot login via the LAN. However, internet access appears to be fully function through the router and the router also responds to pings. (I have the latest firmware loaded.) The only resolve I've found is power cycling the unit to regain login access to it. Very irritating, and impossible when not at the physical location.
View 1 Replies
View Related
Feb 8, 2011
I am setting up One-To-One NAT to redirect traffic from the internet. We have 5 static public IP addresses, and I set up One-To-One Nat to redirect to local Win servers. One of the servers running Web server and FTP server. For some reason redirection works fine for the Web server, but does not work for FTP server when I try to access them from the internet. FTP server works locally, but my FTP client cannot connect from the Internet. I opened the ports in the firewall, and these ports show as opened when I test them from external servers. What am I missing?
View 1 Replies
View Related
Dec 19, 2012
How to setup the quickvpn.... I am getting the message Servers certificate doesnt exist on your local computer..... and the the window fail to establish the connection
View 1 Replies
View Related
Oct 25, 2007
Networking isn't my strongest computer subject area, but I know I'm having a performance problem with my RV082 router. When I direct connect my PC to my cable modem, I can get very near the 7mb/sec rate advertised by my ISP. When I connect the modem to this router, then connect to the pc to the router, the speed drops to between 2-3mb/sec. All tests performed several time using dslreport.com speed test website. The result is very repeatable, so I figure it has to be some delay introduced by the router. I can't see to find any place in the router configuration to do performance tuning. I'm not using any firewall rules except for the default rules. Why I'm seeing a greater than 50% decrease in internet throughput using this router?
View 8 Replies
View Related
Feb 26, 2013
I have a RV082 router that is currently in prod. I have a Dell Powerconnect 5424 switch that I'd like to use in place of the unmanaged switches I am currently using.I have the switch configured with it's IP, subnet, gateway, etc. I can plug devices into it and communicate with no problems. However, when I attempt to plug in the router, nothign will communicate to or from the switch. The devices I plugged in will not talk to each outer, ping the switch, or the router. Also cannot ping to the switch from a device plugged into the router. If I unplug the router, comm opens back up.
View 1 Replies
View Related
Apr 28, 2013
we have a RV082 and have the DMZ option enable for a range of IPs within the same sub-net of WAN IP and this works great. I have another range of Public IPs from our ISP that is not in the same sub-net of the WAN IP and do not see a way on the RV082 to include this 2nd bank of Public IPs in the DMZ.
Our ISP internet feed plugs into the RV082 WAN port and we have a switch plugged into the DMZ port of the RV082 that is used to connect the public devices in the current DMZ. Both banks of Public IPs from our ISP come over via the ISP internet feed plugged into the WAN Port.
My question is, if I cannot configure a DMZ rule to allow this 2nd range of Public IPs to "travel" to the RV082 DMZ port, how I can do this without one-to-one NAT or port port forwarding? The device I am deploying needs to be at the border of our network (like in the DMZ) and have some ability to talk to a device on our LAN.
View 1 Replies
View Related
Feb 17, 2008
I am currently using Netgear FVS338 Routers / VPN Devices in 3 different locations and honestly I am not happy / impressed with them whatsoever.I have been doing some research and came across the Linksys RV042 and RV082 devices that caught my eye. The question is what is the VPN throughput of these devices?I have gone over the website, spec sheets and they only really say the throughput of the LAN Links and not the WAN Links. I currently have very reliable 20Mb+ Synchronous connections between all 3 sites and have not been able to get any good performance out of the Netgear devices and contacting their support is a joke. They can't tell you anything other than it should work or we will swap out the unit. Well if I have 3 of them that have been purchased at all different times I don't believe that they are all having the same issues. What these units 3DES VPN Throughput and will more than likely be purchasing 3 of which ever once suits our needs immediately.
View 9 Replies
View Related
Mar 22, 2009
I am trying to get our internal network PCI compliant and when I run a network scan from securitymetrics.com I receive the following message about our RV082 router.
Synopsis : The remote service supports the use of weak SSL ciphers. Description : The remote host supports the use of SSL ciphers that offer either weak encryption or no encryption at all. See also :[URL]: Reconfigure the affected application if possible to avoid use of weak ciphers. Risk Factor: Medium / CVSS Base Score : 5.0
I have been googling many different search terms for ssl ciphers, rv082, and pci compliance but didn't see any solutions to this. Any experience with ssl ciphers and how to use more secure ciphers? I just performed a firmware upgrade to 1.3.98-tm in hopes that it would fix this issue.
View 2 Replies
View Related
Jul 2, 2007
I have some problem connecting to sites when I'm using the router in Load Balancing mode on the 2 WAN. Looks that when a connection to a site is started with a WAN is not manteined with this one but jump from a wan to the other, causing, in some site like Home Banking to be disconnected every time. I would like to know if it's possible to configure the roouter in Load Balancing but Bindind the source and the destination IP address so the same wan will be used for the entire time this connection is up. In opther words the Load Balancing has a sense beetween connections not beetween the same connection.
View 9 Replies
View Related
Sep 27, 2012
I have a Ubiquiti radio link between my DSL modem and RV082 router and although the router log states that it is connected to the static ip address of the modem i get and NSD fail and have no connection. if I plug the radio link directly into a computer with the static ip I get a connection but the modem has a problem with it.
View 1 Replies
View Related
Jan 17, 2010
Recently I sold a rv082 router to a client.He uses a Windows XP environment to dail in using QuickVPN.A week ago an office admin wanted to connect using Windows 7 and it does not work.The client starts do dial and connects but the connection does not work.The admin does not use a router and there is no active software firewall.
View 3 Replies
View Related
Aug 15, 2012
We have almost identical networks in two offices, with the only difference being, one uses an RV042 and the other an RV082.The setup is: two WAG54GS ADSL modems carry PPOA ADSL connections with static IPs to the two WAN ports of the RV0XX.The WAG54GS routers are configured to DMZ all incoming traffic to the relevant WAN IP of the RV0XXs. VPN pass-through is also set on them. The RV0XX port forwarding is set to forward a selection of traffic such as, PPTP, HTTP, HTTPS, RDP, POP3, SMTP and Remote Desk to the external adapter of an SBS 2003 server which processes all operations including ISA and Exchange.Mail for Exchange arrive through both ADSL connections for redundancy. VPN connection requests from remote users to the SBS come in through both ADSL connections.The office fitted with RV042 works fine and does all the following without problems.The office fitted with RV082 has issues. Remote VPN requests comming from ADSL to WAN port 1 of the RV082 connect successfully to the SBS2003 server, but the VPN requests coming from ADSL to WAN port 2 fail to connect! Similarly, incoming mail destined for Exchange don't get through if coming from ADSL of WAN port 2.I have updated the firmware on both RV042 and RV082, but the RV082 still has the above issues.
View 1 Replies
View Related
Jan 25, 2011
I use SNMP and I dont have access to a router to test.Can the SNMP Trap to: Field in the SMNP section be configured for multiple IP addresses.?
View 1 Replies
View Related
Jan 23, 2008
telnet/ssh sessions time out after 30 minutes of in-activity This only happens in the case of a server that is setup behind the firewall, and of course port forwarding is used. If one unchecks the radio button for the enable firewall the sessions do not timeout at all. This is very reproducable in all recent (1.3.9) versions of RV042 and RV082 routers.
View 2 Replies
View Related
Jul 14, 2011
I have a RV082 Linksys router and at the moment it is slowing down my internet connection by a significant amount. With the router, I get about 3 Mbps and with a modem directly connected to my computer I get about 24 Mbps. Before with the router I used to get 15 Mbps, which is understandable because it is connected to 4 computers total. Maybe my setup has something to do with it. I got a cable that is connected to a modem, the modem is connected to the router, from which one port is connected to a computer, and another is used to connect to a Netgear switch, which in turn is connected to 3 more computers.
Everything was fine until I went on a trip and wasn't home for about 2 weeks, and when I came back, this happened. I tried restarting the modem, the router and all to no avail. I also tried to do a factory reset on the router and again got slow speeds.
View 1 Replies
View Related
