I use Rv016 and config load balance and connect to website [url]... and click Login BANK it can't login and show error page [url].... When I try connect bypass don't use RV016 can connect it. when I try to close firewall service it can't not login again.
View 1 Replies
Currently We have an RV016 setup and Setup>Network we have the following settings:
Host Name: pagegateway
Domain Name: mycompany.com
Device IP address: 10.20.181.1
Subnet Mask: 255.255.255.0
DHCP Server is not enabled on the RV016. We currently have a Windows 2003 Server that is acting as Exchange Server, Active Diretory, and DHCP Server. My issue is that we are running out of IP addresses and I have about 20 or so left to assign. Given the above setting can I make changes to my RV016 to give me more than 256 addresses? If yes what do I need to do and do I need to make any changes on Windows Server?
I have recently implimented an RV016 device into our network. We have a bonded T1 service with Paetec/Windstream (5 static IPs) and also a cable connection with Comcast (no static IP). The T1 has been our primary connection, and our MX and A records all use this IP address. I have the rules set and using a one-to-one NAT setup with our 5 IPs. Everything is working great with the T1 in place and email is flowing with no problems, however when I connect the cable into the WAN2 port and try to send email, its using that outbound connection, rather then the T1 and our spam filter is blocking it. So the email is rejected and we get this message below.
View 1 Replies View Relatedhow to configure Linksys RV016 for two WANs (cable+DSL)? It looks like switching between those two connections not splitting what is set for WAN1 and what is set for WAN2.I set load balancing as- WAN1 (cable) all HTTP up/donw should go there- WAN2 (DSL) GTalk, IMs, SMTP, POP3, IMAP up/down should go therebut looks like is not working that way.When I will go to speedtest.net and test a connection I always get less amount then connected directly through cable : Also when people try to use any session or IP sensitive web site it doesn't let them to log in because session was expired (based on IP) or IP was changed.
View 1 Replies View RelatedI have hardware version 2 and firmware 3.0.2.01 (latest firmware available for this hardware version I believe) and I cannot get it to email me logs. I have entered my outlook address and our SMTP server.
View 1 Replies View RelatedWe have :DSLT-1 I want to route all VOIP traffic and traffic to one IP address over the T-1, all other traffic I want to route over the DSL. HOWEVER, in the event that the DSL fails, have the DSL traffic failover to the T-1.I have setup the router to do just that (I think) and when I go to a site like "whatismyipaddress.com", it shows my IP as comming from the T-1. With the setup I described that traffic should always route over the DSL.Straight up protocol binding won't work because the traffic I want to route over the T-1 to one specific IP is going to be prot 80 and 443 (web traffic)
View 5 Replies View RelatedI just configured a RV016 and it's ignoring my VPN connections and its routes. When I run a tracert to my other site it returns all the hops between they.
View 1 Replies View RelatedMy RV016 does not seem to route traffic that does not originate from the subent that it sits on. For example, I have my RV016 on 192.168.1.1 and a gateway to 192.168.2.0/24 is at 192.168.1.2. None of the traffic originating in 192.168.2.0 is routed by the RV016. I have checked the routing tables and ACLs with no luck. I know the traffic is hitting the RV016 because I setup a packet sniffer. The packets just simply die there. Is this a limitation of the RV016 only being assigned to a single class C? Does it also ignore all internal traffic not from that class C even if the ACLs are open?
View 1 Replies View RelatedCurrently I have a VPN tunnel setup between our company locations. Location A has Linksys RV016 and Location B has RV082. Everything has been working with no problems for the past 2 years with only minor disconnect issues in the VPN tunnel between the locations.
For the past 2 weeks I have been running into issues with the Tunnel. Users in Location B are reporting problems with losing connection to applications that are hosted in Location A. At first I start with doing a ping to router address in Location B and I get "request timed out". Next I login to router in Location A and under VPN I notice that the VPN tunnel is not disconnect (I see disconnect button). Once I click on Disconnect the screen refreshes and that seemed to restablish connecting with router in Location B. The drop connection has been been going on for the past 2 weeks and only happens once a day specifically between 1 PM and 3 PM EST. I have been reading all over the internet and no luck at all. The VPN tunnel settings are the same on both routers and under Advanced options both Keep Alive and Dead Peer Detection (DPD) are checked.
I am trying to setup an RV016 router to do "1 to 1 NAT". I am starting with setting the external IP address of my RV016 to 10.8.58.219 on the WAN1 port, and LAN IP 10.10.20.254. Simple enough. When I connect my laptop to port1 on the router's LAN side I can ping the router's external AND internal IP addresses fine; But I can not ping from outside when connected through WAN1 port.I am performing a simple local test with an external hub, I put a patch cable from WAN1 port to the hub, another patch cable from port 1 on LAN side to the same hub, and from my laptop to the hub. When I use my laptop's IP address with the internal schema (10.10.20.100 for example) I can ping both WAN1 and LAN IP's; but when I use on my laptop the external IP schema (10.8.58.100 for example) I can not ping it. Therefore is not working when I connect my router to the real network.I went into the web setup pages of the router and dissabled: firewall and basicaly all security "blocks" it has, and leave it open for my testing.
View 1 Replies View RelatedI am using a RV016 (192.168.1.2) as a router and DHCP. It automatically assigns its own IP which is 192.168.1.2. I can not set my RV016 to assign a Default Gateway IP of the server. The workstations will connect to internet via this server (192.168.1.1)
View 1 Replies View Relatedjust purchase this RV016 and the firmware has been updated to 3.0.2.01-tm.Every download I try through the router leads to a curruption somehow, even though the download manager gets it all. If I go straight from the cable modem I have no problems.It's a 4mbps upload and 0.8 downlink from what speedtest shows. I have tried diff DL managers, and get the same result on different connected PC's. The great thing about the RV016 is it speeds up the connection on this cable modem.What can I change to get downloads working?
View 1 Replies View RelatedI have a sonicwall firewall connected to the LAN port of the RV016 router and two DSL modems connected to the WAN ports.
Ip address allocation:
Firewall
192.168.50.9
RV016
LAN - 192.168.50.10
WAN - 192.168.60.1
WAN - 192.168.61.1
What configurations do I need to enter into the RV016 to allow other networks connected to the firewall(192.168.3.0, 192.168.2.0) to access the internet?
I am using RV082 V3 router. After a reset of the router I have access via both LAN and WAN for some period of time (not yet known) later that day or the next day when I try to access it via the WAN it sits on "opening page" for a while eventually coming up with the login box. After logining in the page only partially loads. (All the settings are shown, but the proper selections are not made.) Internet explorer will then show something like "8 items remaining" in the status bar. If I close and re-open IE I am unable to connect at all. At this point I also cannot login via the LAN. However, internet access appears to be fully function through the router and the router also responds to pings. (I have the latest firmware loaded.) The only resolve I've found is power cycling the unit to regain login access to it. Very irritating, and impossible when not at the physical location.
View 1 Replies View RelatedI am experiencing loss of internet access when browsing to amazon.com. In addition to losing internet access, I am unable to connect to my BEFSR81 router when this happens. To resolve I have to walk over to my router and reset it by cycling the power.
This issue has been reported by other users of the BEFSR81 too: URL
Details: My BEFSR81 is version 3.0 and is running firmware version 2.51.4
On a BEFVP41, I disabled snmp for testing (because it was sending some strange alarms), and now I can't login to the web setup pages. The username and password no longer work. I thought maybe it reset itself to default (blank/admin) but it didn't.
View 1 Replies View RelatedI recently installed an RE1000, which seemed to be working fine. Then, on 3 PC's with no wireless adapter installed we began being prompted for user name and password for the wireless router. Once I unplugged to extender the problem went away. I know what you're thinking: Maybe I just think there's no wireless adapter on these PC's. NO, I looked in device manager and the only network adapter installed is the ethernet adapter. These are all 4+ year old machines with no hardware changes made to them. Wireless adapters are not necessarily standard issue on old towers--even on new towers. The Acer I'm using right now was purchased new in November 2011 and did not come with a wireless adapter installed.
View 3 Replies View Relatedused to be able to access this secure website [URL] prior to a firmware upgrade. Can no longer access. On Firmware Version: 3.0.2.01-tm. Assuming there's some default setting in the firewall?
View 2 Replies View RelatedWe have a Linksys WRT120N wireless router set up at one of our small offices. I noticed recently when trying to log in to the router to make some admin configurations that it will not accept the login credentials when trying to log in from IE10 browser. Works fine from Chrome, IE9, ect. logging in to a linksys router with IE10?
View 3 Replies View RelatedI purchased and set-up the EA4500 on Thursday. Friday my ISP (Charter) was out and worked on connection for over 2 hours due to slowness issues. Connected directly to modem I get normal ping times on whichever computer is connected. When I get the computer connected by the router (hard wired) I get very long ping responses up to 900ms. They are all over the place 30ms (I can live with that), up to the 900's. I contacted Linksys support last night, who had me update to the cloud firmware and change MT U to 1300, have not noticed a difference. I did end up doing a hard reset on the router last night after I lost tech support. We were disconnected with router rebooted, and I didn't have the patience to connect again last night.
It was so slow on my work computer, a pint to yahoo timed out. The computers connecting to router are
XP SP3 (mine)
Win 7 Home (IPV6 turned off)
Work laptop that uses VPN and VOIP
I have an e2000 wireless router and have several devices connected by ethernet cable including private data on an external hard drive. I am planning to allow a tenant in another building connect via an ethernet cable connected to my router. Can I limit that computer (tenant's computer) from accessing all other devices connected by ethernet cable to my router? I know can password protect wireless access and limit access to the internet that way -- but my question is specifically to connections by ethernet cable.
View 1 Replies View RelatedMy E4200 router no longer accepts any WIRED connections. I can connect from the modem to the computer and everything works as expected. I can connect other computers wirelessly to the router. I cannot connect any laptops WIRED to the router. Nothing has changed on the systems to restrict internet access. There is something wrong with the router and the WIRED ports. I tried going through the troubleshooting on this site but it was of little to no assistance. The Cisco Connect utility doesn't appear to accomplish anything either. My guess is because I cannot connect to the WIRED ports on the router to connect to the internet to allow for whatever troubleshooting that needs to be done.
View 2 Replies View RelatedI have a home network with a wired BEFSR41 that, for a variety of reasons, MUST be manually IP configured (DHCP off). All computers and other devices connected to it are manually IP configured. I desire to add a device that cannot be manually configured, and needs DHCP. I therefore need to daisy-chain two routers with the second one DHCP on (and manual IP connection to the main network). The new device needs two-way internet access, but doesn't care if it sees any other current network devices. I've tried several configurations, none seem to work.
View 3 Replies View RelatedI have a WAP54G in my basement shop, wired to our main router upstairs, which is a Linksys BEFSR81. I'm not sure if this is an issue with the WAP or the router.
I only use the laptop computer in the shop every couple of days, but I leave the laptop plugged in and on most of the time. I used to have the power settings such that it didn't power down completely even after a long time. With that setup, if i didn't use the computer for several days, it would find that the connection to the router had died. The wireless link would report that it had a solid connection, but I couldn't connect to anything. Power cycling the WAP always fixed this.
Recently, I decided to save some wear & tear on the laptop drive, and adjusted the power settings to go to standby after a couple of hours. Now, it seems I can't even go one day without losing my connection.
I am running the latest frimware in the WAP, and the router is version 3.1. I can't check the firmware version on the router at the moment, because the web interface is giving me a blank screen. I know from past experience that I will have to power cycle it to get it to talk to me again.
In any event, it seems like the router connection to the WAP is timing out. I set the router "client lease time" up to 10000 a while back when I first had this problem, but that is clearly not doing the trick.
I have an old BEFSR41 ver. 2 wired outer that I'd like to use with a motorola modem/router as a hub. Is this doable?
View 2 Replies View RelatedWhy there is no parental control feature built in for WAP610N... how do i block website on all computers connected to my router?
View 4 Replies View RelatedThere is a way to block access to a website by password protecting it through my linksys router, which is one of thoe wrt54gs. I know I can completely block access of a website and can restrict the viewing hours of facebook at certain times through the router admin IP site but was wondering if it was possible to make it so you have to use a password to view said certain site. If there isn't is there any way maybe through a program or do I have to go through my ISP to see if they can do what I am asking for.
View 1 Replies View Relatedis there a way i can block a website from being viewed.i would like to do this from the setup page of my e1000 under website restrictions.
View 1 Replies View RelatedI have an E4200 (v1) with the latest firmware. For some reason, the E4200 does not allow me to conenct to certain websites. This is true for wired or wireless connections.To test, I connected a wired PC directly to my cable modem and was able to connect to all websites fine. I also tried an old D-Link router I had on hand and was able to connect to all sites fine. Went back to the E4200 and was blocked. I re-loaded the firmware and same results.
View 4 Replies View RelatedI have a Linksys WRT310N V2 wireless router. Last week it started blocking access to our family website. That website appears to be the only one that is blocked. Every other website we have tried works just fine. I have tried the following.Remove the WRT310N router and plug a computer directly into the broadband modem. After this everything works fine for the one computer I have hooked into the internet.Remove the WRT310N router and substitute an old Linksys non-wireless router. Everything works fine for the hardwired computers on the LAN. Again, not really an option, need wireless access.
Unplug the router and so a soft reset. Still blocks this one website.I have not done a hard reset to factory specs. I wasn't looking forward to redoing everything I had set up.I looked over every setting in this router and can't find anything that would cause it to block a web page. I am far from a networking expert, but most of the settings seem pretty obvious.
I've a BEFW11S4 router that was working fine for 5 years, until the other days it would not let me go to url... but any other websites works just fine.
View 9 Replies View RelatedI got a refurbished E2000 on Amazon. Last night I set it up and when I tried accessing this website [URL], I could not connect to the server. First I thought it's the server problem and let it go. This morning it's the same probelm. I called my local cable technician and he told me it's the wifi router is blocking the website. I called the CISCO guys and they refused as it was out of warranty.
View 2 Replies View RelatedI have a Linksys E2500 wireless router. It seems to be blocking a website (evernote.com). I cannot access this site from any of the computers/ devices in our house, whether they be connected by ethernet or wireless. However, when i move to a different network, I can connect to this site immediately from exactly the devices that do not connect in our house.
How can I determine how/if the router is somehow blocking this site? I have reset the router and upgraded the firmware. Same problem persists. I see nothing in the router settings that would be blocking this site, and I have certainly done nothing intentional in the settings to block this. We used to be able to connect to this with no problems, but all of a sudden, we are blocked.
