Linksys Wireless Router :: Slow Wired LAN Connection On E1200
Feb 15, 2013
I have an E1200 acting soley as an AP. Everything works just fine, but when I try to copy files from one wired computer(both Windows 7) to another one on the same router(the E1200 in this case), the network utilization is only about 4%. If I take one of the computers off its wired connection and make it wireless, the utilization goes up to about 50%. Also if I take one of the compuyters off this router, and make a wired connection to my main router(which is connected via a wired connection to the E1200), the network utilization goes up to 50%.
I'm having an issue with my new E1200 routeur : I have a 100mbit/s connection and since i installed the E1200 , the speed is cut in half : Max 50 mbit/s .. ( or if this is an hardware limitation ? )
I have a gigabit network card with my pc , everything is fine on the pc / network side as i had these speed fine ( 100mbit/s ) with my old ISP router , ( wich i switched in bridge mode to use the E1200)
My newly installed E1200 only sends speeds of about 16 mbps wireless, but sends the ful 60 mpbs when wired. What is going on. Firmware is up to date. Changing the channels didn't do anything. Is there a way to figure out if the problem is with my laptops wireless card.
why I am having a slow connection? Before purchasing Linksys E1200 wireless router, my internet speed was perfectly normal with Netgear wireless router. Everything ran smoothly but once I installed Linksys, it began to have slow connection. It also has drop connection sometimes. How do I fix my connection speed and the drop connection?
I just installed a new e1200 router last night and my ethernet connection is really slow. I've been reading where people's wireless is really slow, but mine is the opposite. I'm getting around .5 mbps download wired, but around 25 mbps download when its connected wirelessly. Is there anything i can do make the ethernet faster or is the router faulty?
I recently purchased an E1200 to replace a broken router. I have had good experiences with this model in the past which is why I bought it. However this has not been so pleasant. For some reason the internet connection over wifi is INCREDIBLY slow. I don't know why. It is fast when connected via ethernet to the router. I changed the MTU on the router to 1400, I set the wireless width to 20MHz and the channel to 11. I set security to WPA2. And yet it is still very very slow. It's not a matter of how many users are on the network; I live in a house with five other people and it's slow regardless of whether everybody's home or nobody is home. It's like this on Macs, PCs, phones and even the Xbox 360. I just did a speed test. Wired was about 14MBps down, wireless was around .7MBps down. I simply cannot comprehend this discrepancy. The old router was very unreliable in terms of connectivity but at least it was always fast. And my laptop is fast at my mom's house where she has an E1200. I use a MacBook Pro from 2009 but like I said,this seems to be affecting everybody in the house regardless of hardware.The modem is a Ubee modem from Comcast. I'd upgrade it to a SURFBoard but my landlord controls all the utilities and I'd rather not have to explain to him how to call Comcast and tell them to register the modem's serial number to the account or whatever.
I just set up my new e1200 wireless router. The wireless connection works great but on my desktop (which is plugged in through the ethernet), has a painfully slow connection. Half the time it times out while loading a website!
I currently have a Linksys E1200 router and I am getting anywhere from .3-.5 of a megabit per second download speed while upload speed ranges from 2-5 Mbps. This is very strange to me as I have never seen a connection this slow or one that had a higher upload speed than download speed.
I have a problem with my new router. I connected't my iMac (27" 2010) and NAS Synology 1511. My problem is the slow connection between mac and router - only 100Mbit (ethernet port on mac is 1Gbit), strange thing... my NAS have 1Gbit with no problem, and the mac is not. I trying manual configure - forcing speed to 1Gbit, but then is no connection at all. I'm also trying changing wires, but no change. Im buying special ethernet cable cat 6 - also no change. Changing ports on router - result the same.
I saw one post recommending to changing the MTU from 1500 to 1400. That did absolutely nothing. My comcast internet is now slower than 14.4 dial up modem I had 16 years ago. The strange thing is I can sometimes download at over 2 mbps with torrents. It's mainly loading websites where the speed is so bad.
I just got a Macbook Air and couldn't get connected at home so I went and bought a new router (our other router was old!!). We purchased the E1200. Our Dell desktop seems to have a fine connection, but my MacBook Air and my husbands laptop are really slow when on the internet.
I just purchased an e1200 wireless router. Wireless speeds seem to be very slow. I'm trying to transfer 1 file to my media server, and am only getting 221kb/s. Also, internet connection seems to be slow as well (though if I plug directly into the router or the modem, I get speeds of 25Mbps, however when connecting wirelessly via the router I get speeds closer to 2Mbps (according to speedtest.com).I've played around with the settings as per other posts, and seemed to get the best speeds with the following config (however it is still very poor):
- security mode: WPA2 Personal - network mode: B/G (have also tried N, which gave worse speeds) - channels 1,3,6,9, and 11
I'm owner of Cisco RV082 router and I have a problem with firewall setup.I would like to deny internet access on port 80 (all sites) for group of users, and allow them internet access for one site by HTTPS (443)After applying rules internet connection is really slow.. Users have to wait something like a 30 sec for a website..I descovered that the reason for slow internet connection is DENY rule. After disbling DENY rule everything works fine..Now I have a few rules added to firewall:
Priority:1 Action: Deny Service: HTTP(80) Source interface: LAN Source:10.82.0.51-10.82.0.245 Destination: Any
I just got an E1200 router and connected wired to my win 7 machine, Im clocking in the single digit ranges (~8 mbs) download but on my dusty old win xp laptop wireless, Im getting 20 mbs (max speed from isp 20 mbs). Wife's Mac laptop wireless, same speed. What is going on? I updated the firmware, tried altering some settings based on other entries here suggested (WPA-personal, channel to "6") but no effect.
Both the router and modem are new. Connecting directly to the modem I get Mbps, but the router speed is Kbps. I upgraded the firmware and made various changes per Google searches
I have an E1200 that will work fine for a while, then suddenly the download speed for all wireless devices will drop to between 20-30 KB/sec. It happened last night when we were watching videos on Hulu. We were blazing along fine, when all of a sudden the connection was horrible enough that we had to stop watching. We have no idea what changed - there are only two of us in the house and we were both passively watching Hulu.
This has happened before, and usually changing something like the wireless channel has fixed it, but not this time. The PCs we have that are connected to the router via Ethernet get between 1-3 MB/sec, so I know it's not the modem or the ISP.The signal strength is good (4-5 bars). I have tried repositioning the router and the wireless reciever but that hasn't worked.I have the latest firmware for the router as far as I know (v2.0.02).
I have tried every channel available (including "Auto"). I have tried switching the Channel Width between Auto and 40 MHz. I have tried resetting the router to factory settings and re-uploading my configuraiton. I have tried setting QoS.
I upgraded my old router to a Linksys E1200 about 2 months ago. Like others with Comcast, I now have a lot slower internet speeds. I've updated everything, disabled WMM. I'm still getting slow speeds. My download speed is 3.12, which is not that bad for me. However, my upload is just below 1.
I just bought a Cisco e1200 router... and the wireless connection is way too slow, when navigating through the web, but when using speed test, the connection seems fine, but still it even takes more than usual to open simple pages, lets say Google... i usually watch streams and now that i cannot do... when i connect directly i can do everything as usual...as i have read, i change channels, but still no improvement, i have the latest firmware, on my range there are only 2 more available connections... i even tried disabling/enabling the WMM... We all know that having extremely slow internet must be the real "Mayan apocalypse"
I just bought this router and set it up using its CD. It looked like everything was fine until I connected my laptop using wireless. The wireless download speed is absolutely ridiculous. My wired desktop shows 35mbps while my laptop is 0.5mbps. Upload is same for both. Clearly something is limiting my download wireless.
Contacted Cisco support and they told me to change the mtu to 1400, change channel to 11 and reboot. Nothing worked. I have the latest software.
I have been having a problem with my router for the past two weeks and my ISP (RCN) has done nothing to fix it so maybe with our nerd power combined we can find a solution!My router runs fine about 60% of the time, I get 20-24Mbps down and 2Mbps up connect wirelessly. the other 40% of the time the download speed suddenly drops to 1.5-2Mbps down and 1Mbps up. There is nothing in particular that I will be doing at the moment it just suddenly dies.Things I have done that have not worked.I have changed my channel to 1,6,and 11.Updated firmware.Factory Reset (New broadcast name/password).Set up static IPs.I have tried disabling WMM Support and this just kills any connection wirelessly to the router.Is there anything else you can think of to fix the issue, or should I just be demanding a new router the next time they come
I have the E1200 and since I installed this router, the wireless download speed on my iPad and iPhone has been only around 4 to 5 Mbps when my other wireless devices could get to 7 Mbps and ethernet gives close to 10 (my ISP gives 10 Mbps max).I know many people experience slow download and normally disabling the WMM would solve the issue. But this doesn't work for me and I've made sure i'm on the latest firmware.
The wireless router, which is a linksys E1200 is completely new. I setup the entire wireless and there was no problems on that front.The problem is the wireless connection. Even when I am within a few inches of the router, I couldn't even load a youtube video properly. It buffers every 2 seconds. But when I plug the cable into my computer, it works completely fine. The signal strength is excellent all the time.
I tried using inSSIDer to look for the number of connections within my area for the one with the least inteference and found that I'm already on the good one, or actually, all of them looked more or less the same. But I tried changing anyways from 1 to 6 to 11, and none of them made a difference.I then tried changing my Wireless Security to WPA2 Personal. Then I tried changing the Wireless Network Mode to Wireless-G Only instead of Mixed and the wireless speed increased.
I recently set up a new E1200 router to replace my old one. We are having problems with very slow download speeds (often <0.10 Mbps) even while the upload speeds are OK (8-10 Mbps). Our previous download speed over wifi was 10-15 Mbps.When I first set it up, the download speed was very poor on the initial computer. After fooling around, it was fine. I don't know what I did that made it speed up. However, my wife's computer has had very poor download speeds. After rebooting my computer, the download speed has also dropped bak to <0.10. I was able to stream Hulu on my Wii just fine an hour ago.
i recently switched from a wrt54g to a Cisco e1200 and my average torrent download and upload speeds went to 1200/kbps 100/kbps to around 200/kbs 0-1/kbps i got the latest firmware tried different channels disabled the wmm I've also tried wireless n only and wireless g only. I have no way to test the wired speed. I have a n adapter.what do i do.
I am trying to extend my home network into my basement with both wired and wireless connections. I have a WRT120N upstairs, which is connected to my cable modem. I have an E1200 in the basement, which I have connected with a LAN port. DHCP is turned off, and all wired connections are getting an address from the upstairs router, and connecting to the internet successfully.I've configured the wireless with the same SSID on both routers, but the clients that connect to the downstairs wireless are not able to access the internet. They are getting an IP address from the upstairs router, but can't get past the gateway.
I installed an E1200 router today. It automatically upgraded the firmware to the latest when I did this. Everything went smoothly.
I connected my desktop wired and my laptop wireless. I ran three different speed tests: Xfinity, speedtest, and cnet. All three showed 25-35 Mbps download and 4-5 Mbps upload. That is what my old router had too. So far, so good.
I ran the speed test that came with the E1200 router. It showed 0.30- 0.66 Mbps download and 0.58 - 2.09 Mbps upload. Note the decimal points!
Bottom line: The E1200 seems to be working fine, except that its internal speed test seems to be broken, at least when testing from a wired machine.
I purchased E1200 and have a problem. I have static external IP but router configured to get IP automatically (reservation from ISP). When some one at home using internet I can commetc to the router using remote management. But when everybody out and no internet users at home I cannot connect to the router. I checked with other router from linksys (old one WAG45G or something like this) and it was the same. But it works great whith TP-Link routers.
I upgraded from a E2000 to a EA4500 today and I am experiencing slow wired WAN speeds. On my E2000 I get approximately 60Mbps down and approximately 2Mbps up, and when switching over to the EA4500, I can only manage about 20Mbps down and about 2Mbps up. I can switch back and forth between routers and replicate the results every time
Set up my new E4200V2 last night, everything appeared to be working but while streaming videos over wired LAN I get short hiccups over wired. While streaming videos, a few second long pause is really, distracting, this is a deal breaker and my previous router (DIR-655) had no issue streaming any videos. The wiring has not changed, only the router.I set up a ping between two wired linux boxes, and get: [code]
Whoa, 10 ms over gigabit LAN. This is crazy, but doesn't tell us much. The 10 ms was one out of hundreds of pings, so its only intermittent. This might explain the hiccups, but this router doesn't appear to log anything, so its hard to say.Next was scp transfers, which never exceed 15MB/s, in either direction. For gigabit, wired LAN this is awful, with my previous DIR-655 I would get at the very least 40 MB/s, in all situations.Next up, iperf. I set up iperf on the two hosts, and iperf reports reasonable gigabit speeds. [code] Tonight I am thinking of reverting to an old firmware, doing a hard reset and seeing if it persists, and if no ideas come up in this forum, it is getting returned, 15MB/s over gigabit lan is terribly broken.
I had recently purchased the E1200 router. For some reason, my internet keeps going in and out of service. I will be playing an online game but get disconnected from the server every 6-8 seconds. I tested if it could be my internet provider, but when I connect via Ethernet cord to my modem, it works great. If I run the Ethernet through my router or try wireless connections, it tends to go in and out. It only seems to do this some of the times.
I have E1200 router and I have a problem with setup my ISP Connection. The ISP requires PPPOE connection but with static IP Address but in E1200 I didn't find any option for that. The possible ways are PPPOE or Static IP Address.
