I just got an E1200 router and connected wired to my win 7 machine, Im clocking in the single digit ranges (~8 mbs) download but on my dusty old win xp laptop wireless, Im getting 20 mbs (max speed from isp 20 mbs). Wife's Mac laptop wireless, same speed. What is going on? I updated the firmware, tried altering some settings based on other entries here suggested (WPA-personal, channel to "6") but no effect.
View 2 Replies
am having speed issues on the wireless side of my WRT54GL v1.1 router.When I hook up a laptop to the wired port, am getting roughly 5.4mps down when wired, but only 1.2mpbs down on wireless. I am tried doing a factory restore. I have made sure that no QoS is in place. I have tried multiple devices to make sure it is not something on the device side causing this problem, but all the devices perform just as poorly on wireless but as well on wired.
View 5 Replies View RelatedMy newly installed E1200 only sends speeds of about 16 mbps wireless, but sends the ful 60 mpbs when wired. What is going on. Firmware is up to date. Changing the channels didn't do anything. Is there a way to figure out if the problem is with my laptops wireless card.
View 9 Replies View RelatedI just upgrade my service with Comcast so I can now get up to 50Mbps, however the modem when directly connected to the PC can obtain these speeds, it does not when the PC is connected to the E4200 router. In fact the Cisco Connect speed test shows the upload speeds (10+ Mbps) to be faster than the download speed(4.82 Mbps). I upgraded the firmware to the latest level but it did not make a difference.
View 4 Replies View RelatedI have an E1200 acting soley as an AP. Everything works just fine, but when I try to copy files from one wired computer(both Windows 7) to another one on the same router(the E1200 in this case), the network utilization is only about 4%. If I take one of the computers off its wired connection and make it wireless, the utilization goes up to about 50%. Also if I take one of the compuyters off this router, and make a wired connection to my main router(which is connected via a wired connection to the E1200), the network utilization goes up to 50%.
View 3 Replies View RelatedI'm having an issue with my new E1200 routeur : I have a 100mbit/s connection and since i installed the E1200 , the speed is cut in half : Max 50 mbit/s .. ( or if this is an hardware limitation ? )
I have a gigabit network card with my pc , everything is fine on the pc / network side as i had these speed fine ( 100mbit/s ) with my old ISP router , ( wich i switched in bridge mode to use the E1200)
I am trying to extend my home network into my basement with both wired and wireless connections. I have a WRT120N upstairs, which is connected to my cable modem. I have an E1200 in the basement, which I have connected with a LAN port. DHCP is turned off, and all wired connections are getting an address from the upstairs router, and connecting to the internet successfully.I've configured the wireless with the same SSID on both routers, but the clients that connect to the downstairs wireless are not able to access the internet. They are getting an IP address from the upstairs router, but can't get past the gateway.
View 1 Replies View RelatedI received a Linksys E1200 Wi-Fi Router for Christmas. I inserted the Setup CD into my iMac, running OS X version 10. 8. 2. I clicked on setup and a window opened with the message "Unsupported operating system".At this point I don't plan to use the Wi-Fi for the computer, but I do need to connect the ethernet cable to the router, then to my computer.I will be using Wi-Fi for my iPad. In that case, I have no instructions on how to set up the router for my iPad. Will this Wi-Fi router work or will I need a router compatible with OS X version 10.8.2?
View 1 Replies View RelatedMy Wi-Fi keeps on freezing and I have to unplug it all the time. I have the e1200
View 9 Replies View RelatedMy 1200 v 1.0 was working fine until I tried to link a wireless internet camera. Apparently I screwed something up in the setup such that I've lost my WiFi connection to my laptop and one wireless desktop. Fortunately my wired connection still works. I've carefully tried to restore my system following the online procedure and while the setup looks OK it doesn't link. In the process I have reset the router to the factory setting several times and have installed the latest firmware version. I contacted Linksys support and using remote diagnosis they reached a point where they said that something was wrong with my computer and to investigate further there would be a fee charged. I balked at that since I had tried the setup from several different wired Window 7 and XP computers.
View 9 Replies View RelatedOkay so my friend recently bought a Linksys E1200 Wireless-N Router. We set it up the other day and it all appears to be functioning just fine. The only problem is when we log into her wifi it says "No Internet Access". I'm moderately okay when it comes to computers but not expert and I'm horrible at the whole wifi router thing. Through my laptop I've done a Windows Network Diagnostic to see what was wrong and it says that my "computer is correctly configured but the device or resource (DNS server) is not responding."
View 8 Replies View RelatedI just bought a E1200 routerand using automatic setup by using CISCO connectafter that, I only got a CONNECT SPEED with about 10Mbps in my android smart phone,I would like to know how can I increase the WIFI strength WITHIN THE WIFI SETTING, I chose MIXED mode rather than specific in b/g/n mode.
View 4 Replies View RelatedI have the E1200 and since I installed this router, the wireless download speed on my iPad and iPhone has been only around 4 to 5 Mbps when my other wireless devices could get to 7 Mbps and ethernet gives close to 10 (my ISP gives 10 Mbps max).I know many people experience slow download and normally disabling the WMM would solve the issue. But this doesn't work for me and I've made sure i'm on the latest firmware.
View 5 Replies View RelatedFor some reason I can no longer make Wi-Fi calls with my E1200 router. I have checked with my ISP and T-mobil. They both tell me that everything on their respective ends is working correctly. The only piece of the equation is the router.
View 5 Replies View RelatedThe wireless router, which is a linksys E1200 is completely new. I setup the entire wireless and there was no problems on that front.The problem is the wireless connection. Even when I am within a few inches of the router, I couldn't even load a youtube video properly. It buffers every 2 seconds. But when I plug the cable into my computer, it works completely fine. The signal strength is excellent all the time.
I tried using inSSIDer to look for the number of connections within my area for the one with the least inteference and found that I'm already on the good one, or actually, all of them looked more or less the same. But I tried changing anyways from 1 to 6 to 11, and none of them made a difference.I then tried changing my Wireless Security to WPA2 Personal. Then I tried changing the Wireless Network Mode to Wireless-G Only instead of Mixed and the wireless speed increased.
I recently purchased an E1200 to replace a broken router. I have had good experiences with this model in the past which is why I bought it. However this has not been so pleasant. For some reason the internet connection over wifi is INCREDIBLY slow. I don't know why. It is fast when connected via ethernet to the router. I changed the MTU on the router to 1400, I set the wireless width to 20MHz and the channel to 11. I set security to WPA2. And yet it is still very very slow. It's not a matter of how many users are on the network; I live in a house with five other people and it's slow regardless of whether everybody's home or nobody is home. It's like this on Macs, PCs, phones and even the Xbox 360. I just did a speed test. Wired was about 14MBps down, wireless was around .7MBps down. I simply cannot comprehend this discrepancy. The old router was very unreliable in terms of connectivity but at least it was always fast. And my laptop is fast at my mom's house where she has an E1200. I use a MacBook Pro from 2009 but like I said,this seems to be affecting everybody in the house regardless of hardware.The modem is a Ubee modem from Comcast. I'd upgrade it to a SURFBoard but my landlord controls all the utilities and I'd rather not have to explain to him how to call Comcast and tell them to register the modem's serial number to the account or whatever.
View 2 Replies View RelatedRouter: E1200 2.0.02 build 3 Feb 15, 2012
These symptoms are stumping me:
WiFi drops 80% packets from new computers (Win7, IPv4 andIPv6 enabled) to reliable internet hosts. WiFi is OK (0% loss) from new computers to E1200 itself (ping E1200 IP address).Old computers, mobile devices, and wired are OK to reliable internet hosts.Basic Wireless Settings are Mixed, Auto Channel Width. Wireless Security is set to WPA2/WPA Mixed Mode. Guest Access enabled.
I just bought the Cisco E1200 about two weeks ago to replace an older Linksys non wireless router. With my old Linksys, I had an Acess Point installed, a trendnet TEW-638APB. Now that I have the new Cisco E1200 which itself is wireless, I'd like to add my TrendNet Access Point to the netowork and extend the wireless range. However the place in the house I want to put it does not have any CAT-5 cable running to it so I'm trying to set up a bridged connection between the two. I'm a bit new to netoworking stuff but I catch on pretty quick. I've been doing research on it all day between the TrendNet AP and the Cisco E1200 but I'm still a little lost. I've got WDS enabled on the TrendNet AP and have the first MAC address set to the Wireless MAC address of the E1200 but I don't get what to make the next three MAC address. Somone told me to make all 3 of them 00:00:00:00:00:00. Is that correct?
I also have both the E1200 and the TrendNet AP set to the same channel, both are on a 20Mhz channel width, Both have the same SSID though I'm pretty sure that doesn't matter in the long run from what I've read. Also, no incryption on either (no need for it out here).So I guess I'm just wondering how do I use the E1200 as a Wireless Base Station? If that's what it's called? I have upgraded the firmware of the E1200 from 1.0.00 to 1.0.03 but that didn't change anything in regards to seeing an option for a bridging mode or anything. Other than that I'm not sure what else to do.
I have an E1200 model 1 router. I've owned it for over a year and it's given me no problems until now...Hardwired ethernet connections work fine, but the wifi no longer works consistently. I have several wireless-N wifi devices that either cannot connect to the router at all (they present an error message), or do connect but will not load anything over the connection, or will load web pages very very slowly and then suddenly drop the connection.When I go to the DCHP client table, I see all of my ethernet connections but it does not show any wifi devices, even if the WiFi device is showing a connection to the router.The wifi connection is secured via WPA2 Personal.I have tried changing channels to one that was not congested with any other nearby routers. I have also tried a 30-30-30 factory reset. I am updated to the latest firmware version (1.0.03). I am sure I am entering the correct pass phrase to connect over WPA2. All of my wifi devices are confirmed to be wireless-n, not g or b.
View 7 Replies View RelatedWe have a Linksys E1200 modem and I have been having problems with keeping my son from using the wireless interenet. I did change the password and that worked for about 24 hours and then he was able to get onto it again. He has a nintendo dsi and he is smart enough to figure out how to dismantle any parental controls on his gaming device. I think that he resets the modem in order to get back onto the internet in order to use his gaming device. Someone told me that you can register each item individually in order to keep kids from using it but I have no idea as to how this works. We have two iphones, a lap top, and two tablets.
View 7 Replies View RelatedI installed an E1200 router today. It automatically upgraded the firmware to the latest when I did this. Everything went smoothly.
I connected my desktop wired and my laptop wireless. I ran three different speed tests: Xfinity, speedtest, and cnet. All three showed 25-35 Mbps download and 4-5 Mbps upload. That is what my old router had too. So far, so good.
I ran the speed test that came with the E1200 router. It showed 0.30- 0.66 Mbps download and 0.58 - 2.09 Mbps upload. Note the decimal points!
Bottom line: The E1200 seems to be working fine, except that its internal speed test seems to be broken, at least when testing from a wired machine.
If i go wired i get 100mbps on both my laptop and desktop unit if i switch to wireless they both go 135 to 150 mbps any ideas? both units have megabit cards. My laptop i use at work at 1.0gbps no problem. It doesnt change no mater where i plug into at home or with different cables same speeds
View 2 Replies View Relatedwhy my wireless connection on my laptop is significantly better than my wired connection to my desktop. Internet ran just fine on the desktop at my old apartment; got to the new place, and now it's having serious issues.
After working on this problem for a while, I have come to the conclusion that for some reason, I am getting serious packet loss, consistently, at a particular "hop" on my desktop, which is not present on the laptop.Here are the Line Quality tests that illustrate the problem better than I could ever describe it in words:
Laptop: Line quality test packet loss and latency | DSLReports.com, ISP Information
Desktop: Line quality test packet loss and latency | DSLReports.com, ISP Information(and it appears they both fail the initial test, but the laptop connection runs just fine).
So at that one specific hop (ae-1-0.cr0.chi10.tbone.rr.com, I have no idea what that means), my desktop connection suffers serious packet loss while the laptop is more or less OK.This discrepancy is evident in the quality of connection on my desktop, while the laptop runs just fine. Here, in summary, is what I have tried:
-Going wired through laptop using same cables, ports, and router as desktop: laptop performs flawlessly.
-Updating router firmware, NIC card drivers, and Windows on the desktop
-Full virus disk scan and boot scan using Avast; full malware scan using Malwarebytes; Windows disk defrag
-Disabling QoS packet scheduler
-Performing netsh /flushdns; winsock reset; ipconfig release, renew
-(Temporarily) disabling Antivirus program
All of these actions together have made the desktop connection USABLE... however it is by no means an acceptable level of quality for a cable connection, and not nearly as good as any other in the apartment gets using the same connection, whether wired or wireless.The only visible difference I can find between the laptop and the desktop is the packet loss that is present at that one hop in particular, which is extremely debilitating for the desktop's connection.
Further info:
Desktop specs:
Realtek PCIe GBE Family Controller NIC (onboard on the mobo)
Windows XP Home Edition Version 2002 SP3
Intel Core 2 Duo E8400, 3GHz
2 GB Ram
Plenty of Disk space
Router:
Belkin F5D9230-4 Wireless G Plus MIMO Router
Here is the previous thread that details my troubleshooting efforts thus far; as the question has now become something entirely different, I thought it more appropriate to make a new thread.
Wiresless faster than wired connection
Just got cable and new hardware and been running bandwidth tests. I know wired is always going to be faster than wireless but was wondering if there were things I can do to see where the bottleneck is.
I have cable internet with a sb6120 modem and the asus rt-n56u router. When I go wired, I get 40+mbs down and when I go wireless I'm getting approx 20mbs down. Dont get me wrong, this is more than adequate but was wondering why the huge difference. I'm not anywhere close to the theoretical max.
The rt-n56u is on firmware 1.0.1.7f which is current. My desktop uses the WMP600n and my laptop has the Intel 5100 AGN built into it - both have updated firmwares.
DSL modem works fine when connected directly to computer. No internet output from WRT54G wired or wireless, but wireless network is recognized by computer, just no internet. I did a reset and installed the latest firmware, then I ran thru the setup CD that came withe the router, and the internet test said no internet connection was available. Cables are fine, connector innards look clean.
View 4 Replies View RelatedI have a E3200 Router and when the computers are connected directly to router (Wired) the speed is SLOW and when computers are connected via wireless the speed is fast (normal). What can i do to have the wired computer with same fast speed as wireless?....i'm i missing something?Here are the speed results:
All wired computers connections (total of 4) downwload speed ranging from 8 Mbps to 13 Mbps.
All wireless computer connections download speed stable at 49 Mbps.
I have a WRT120 wireless router that works fine, but the wired connection has failed. I have restarted the modem, router and the computer and still doesn't recognize the wired connection.
View 9 Replies View Relatedget a new router. but lets give it a try. I read many many post on how to optimize the speed of the router but none worked so far.I got a great wired Internet connexion hitting between 45 to 60 Mbps[URL] the wifi is crazy slow on Iphone, Macbook pro and iPad staying between 3 to 8 Mbps....
I tried to change all of the specs, did the firmware update. is there a perfect configuration with the new firmware ?
I've got a 2 month old e3000 with the latest firmware. (1.04 i believe) I have run speedtests from wired and wireless machines on my network. All of the wired connections show a speed of around 15Mps (which is consistent with my providers guaranteed speed) but when I test any of the wireless connections I get somewhere between 3 and 7 Mps. I get the same degradation in speed when I stand directly next to the e3000.
Other then SSID and Passphrases I have everything set to the default settings. I have rebooted multiple times with no change. The e3000 is mounted on a 2x4 with several feet of clearance all around and is also located in the coolest part of the house. I am using Speedtest.Net for all the tests.
In the next month or so I plan to replace my old desktop PC. It is currently connected to a Linsys E3200 wireless router. I have many other wireless devices also running off the E3200, but my PC is the only wired device connected to it. When I replace the wired PC do I simply switch the new one in with the existing ethernet connection (I'm sure it is not that simple) or do I have to start over again recreating my entire network..security etc.. ? If so what is the process to start over ? Do I have to reset something on the router, reload cisco connect, create a new network name?
View 4 Replies View RelatedI've been experiencing a strange, repeatable behavior with my Linksys E1000. I have several wireless and wired devices connected to my E1000:
Wired: TivoHD, Sony BluRay Player, Sony TV, Windows XP Wireless: Lenovo Laptop (Windows 7), HP Laptop (Windows 7), 3 iPods, 2 iPhones
When I try to copy large files (~ 4GB) from my (wired) Windows XP box to either of my (wireless) laptops, the Linksys drops my WiFi network -- but the wired connections continue to work (including internet access). Copying the same/similar file from a WiFi device to a wired device appears to work correctly, as does copying from WiFi to WiFi.
To be clear, my WiFi network "disappears" -- it is no longer listed as an available network (as opposed to just dropping internet connectivity for WiFi). Unplugging the router and plugging it back in brings my WiFi network back up.
I have been able to repeat this issue with multiple files over the course of several weeks, and it happens about 75% of the time (i.e., I am occassionally able to complete a file copy from wired LAN to WiFi).
A little bit of background: I resurrected an old Windows XP box and am using it for shared network storage. I copied about 400 GB of files from my laptops to the XP box (WiFi to wired) with no issues at all. Pulling the same files back from XP to my laptops (wired to WiFi) has been causing the issue described above.
I just bought a new WRT120N Router. It worked perfectly wired and wireless.But my old laptop burned, and the new one came with a Atheros AR5B93 Wireless Network Adapter, which is Draft-N compatible.The laptop connects to the router fine, but using only the G type. When I set the router to use only 802.11n, i get a message from Windows, like: "Windows was unable to connect to the network."because the N configuration is much faster than the old G.
View 9 Replies View RelatedCould I use DHCP for wireless connection and assign private IP for PC for wire connection ?Will it conflict to each other ?
View 3 Replies View Related
