Linksys Wireless Router :: E3200 Wired Too Slow / Wifi Fast?
May 19, 2012
I have a E3200 Router and when the computers are connected directly to router (Wired) the speed is SLOW and when computers are connected via wireless the speed is fast (normal). What can i do to have the wired computer with same fast speed as wireless?....i'm i missing something?Here are the speed results:
All wired computers connections (total of 4) downwload speed ranging from 8 Mbps to 13 Mbps.
All wireless computer connections download speed stable at 49 Mbps.
View 2 Replies
ADVERTISEMENT
Nov 12, 2012
Why my E3200 is (for lack of a better word) "throttling" my internet speeds.I'm signed up for my ISP's 50Mbps data plan. When I hook up my laptop directly to the cable modem (via LAN cable), I see close to 50Mbps as the internet speed (measure via speedtest.net). When I hook up my router to the cable modem, and connect via LAN cable to the router, the internet speed comes down to around a maximum of 26Mbps. NOTE, that I am still talking about a wired connection and not a wireless access. Speed tests with the wireless access do yield the same results as well. To rule out the obvious, I've confirmed that there aren't any other devices on the network and no other bandwidth hogging applications running while I performed these tests.
View 9 Replies
View Related
Jan 15, 2012
In the next month or so I plan to replace my old desktop PC. It is currently connected to a Linsys E3200 wireless router. I have many other wireless devices also running off the E3200, but my PC is the only wired device connected to it. When I replace the wired PC do I simply switch the new one in with the existing ethernet connection (I'm sure it is not that simple) or do I have to start over again recreating my entire network..security etc.. ? If so what is the process to start over ? Do I have to reset something on the router, reload cisco connect, create a new network name?
View 4 Replies
View Related
Jul 19, 2011
I just set up a new computer with win 7 - 64. The cable broadband download speed is less than 1 meg/sec. My wife and daughters computers, which are wireless, see now slowdown. My computer is connected to the router thru the ethernet connection. The previous computer using win xp - 32, plugged into the same router had no unusual speed problems. I did turn off the windows 7 firewall. Did no good.Could there be some incompatibility between the router and win 7 - 64?? Are there some settings that need changing?
View 1 Replies
View Related
Jun 25, 2012
get a new router. but lets give it a try. I read many many post on how to optimize the speed of the router but none worked so far.I got a great wired Internet connexion hitting between 45 to 60 Mbps[URL] the wifi is crazy slow on Iphone, Macbook pro and iPad staying between 3 to 8 Mbps....
I tried to change all of the specs, did the firmware update. is there a perfect configuration with the new firmware ?
View 9 Replies
View Related
Jun 22, 2011
My newly installed E1200 only sends speeds of about 16 mbps wireless, but sends the ful 60 mpbs when wired. What is going on. Firmware is up to date. Changing the channels didn't do anything. Is there a way to figure out if the problem is with my laptops wireless card.
View 9 Replies
View Related
Mar 5, 2013
I bought my own modem, a Motorolla Extreme something or other, is a DOCSIS 3.0. My router is a Belkin N150. When I plug my desktop computer directly into the router, I get speeds upwards of 50Mbps. The wireless, however, gets about 0.15Mbps download, but as much as 12Mbps upload.
I know it's not computer specific, because I plugged my laptop directly into the modem and got the full speed. AND I put a wireless adaptor on the desktop and got the slower speeds.I live in a densely populated area and there are 27 other (visible) wireless networks available (all locked, unfortunately. Otherwise I wouldn't be in this situation in the first place). So I tried every channel, doing a speedtest with each, and I got almost identical results each time: 0.12-0.17Mbps download, 11-13Mbps upload. I can't imagine that getting only 0.15Mbps could be a result of a channel being clogged, but I tried it anyway;
View 2 Replies
View Related
Apr 2, 2012
I have a Linksys E1550 Wireless Router that is fast as can be on the wired connection, getting 30mbs from the cable modem connection. If I switch to using wireless on the same PC, the max connection speed I'll get is 2mbs. I've changed all sorts of settings trying to get this working right, and it still stays at 2mbs.As an additional note, this router was previously working fine at 30mbs on wireless as well, then out of nowhere this weekend, it started running at 2mbs. I went and purchased another of the same model and it is doing the same thing as well.
What is the secret to having this run at it's correct speed, not this slow 2mbs that it is now? I have configured this the same as every other Linksys router I've had in the past, and it is running horribly slow..I'm on the newest firmware as well, have already verified that. The old router was updated to newest firmware as testing to resolve this, and the new router came with it installed already.
View 6 Replies
View Related
Nov 15, 2011
Webpages sometimes load quite sluggish and when playing an online game I am experiencing much more lag. However, if I try loading the same webpages a few minutes later, they will being loading fast again. It seems as if my internet is periodically slowing down. Using speedtest.net, it shows 10Mbps download and 9Mbps upload. However, sometimes when I run speedtest again, the download portion will hang and the test won't complete.My internet provider is COX Communications. I do not think I am using a router as it is university provided internet so I connect my Ethernet directly into the wall jack.
View 3 Replies
View Related
Dec 22, 2011
So I have installed my new E4200 version 1 and I am disappointed with the speeds. My computer has a wireless N card and gigabit Ethernet compatibility. I am currently getting a miserly 54 mbs wireless and 100 mbs on the wire (connected with cat6 all the way)... Anything I should try to get close to advertized speeds?
View 9 Replies
View Related
Aug 31, 2012
I have an E3200 router. I had been experiencing connection problems with my desktop that was wired to the router, and in an attempt to resolve the issue reset the router to its factory defaults. Now, as before the reset, I can connect to my router just fine via Wi-Fi (I have several devices connected this way) but none of the computers that I attempt to connect via ethernet are able to establish a connection. I have tested multiple cables with multiple computers using multiple ports on the router, to no avail. When I view the Status --> Ports page on the router, I can see the ports in use that I am connected to, but that is the only sign of connection that I get.
View 1 Replies
View Related
Nov 19, 2012
I have a 10 Mbps Internet connection, if I connect my PC directly to my modem I get the 10Mbps sometimes more, also I get them if I connect my modem to my switch and from the switch the computer.The problem comes when I connect my modem to the D-link DIR-600 router and from the RJ-45 connectors of the D-link I connect my computer, i get 0.80, 1.5 max. and my wifi devices gets the 10mbps. What is happening with the D-link RJ-45 slots or im missing something in the configuration?
View 1 Replies
View Related
Jun 20, 2012
I just bought a synology NAS ds212j . I updated to DSM4.0. I purchased 2 Seagate ST2000DM001 Barracuda 7200RPM 2 TB SATA 6 GB/s NCQ 64 MB Cache 3.5-Inch Internal Bare Drive
My e3200 has the latest 1.0.04 firmware I'm backing up via time machine(mac book pro) in MAC 10.7.4 which has a wireless N card.
in Utilities (activity monitor)I'm only getting 9 megabytes per second , why is it so slow? I feel like it's taking forever. e3200 says it does up to 300 megabytes per second. any possible settings causing this?
a backup of 202 gigs has been running for about 4 hours and still going
View 9 Replies
View Related
Feb 13, 2012
Ok, so I recently upgraded to a Linksys E3200. I am trying to get the QoS to work properly. I know that it is supposed to prioritize network traffic, so that if I have busy traffic but I am playing an online game, it should keep my gaming from stuttering while slowing other traffic down.
The problem is that every time I enable QoS everything slows down dramatically. I had a 200MB download that was going to take 5hrs with QoS enabled, that took 10min with QoS disabled. And with QoS enabled I can't even watch a youtube video without it pausing to buffer every 10 seconds. And that was the only PC/device using the network at the time. Again turning off the QoS WMM option solved the problem. I have noticed this problem with multiple routers and brands and usually just disable QoS as soon as I set up a router, however I heard that I won't get the full benefit of 300Mbps without QoS enabled.
I don't have any special Voice over IP needs, or video streaming etc. and I rarely am using multiple network devices at the same time. Is there really any reason I should enable QoS? Also I never really play with the settings for QoS, I just figure that since it comes enabled by default it should work for the average consumer.
View 9 Replies
View Related
Nov 9, 2012
Each time I'm rebooting my E3200 device my ping to my ISP is 20ms. Few hours later the ping goes up to 300-500ms.Than I reboot again and the ping is going down to 20ms again.
View 5 Replies
View Related
Nov 7, 2011
I finally decided to go with a e3200 yesterday and picked up one at Walmart. Last night I went to hook it up and had no luck setting it up. Now I have able Internet with a phone VoIP service. After trying to connect several ways, all the router wants to do is sit with a flashing power light. I cannot access the setup page wireless or wired and have tried several methods I found last night.
View 1 Replies
View Related
Aug 14, 2011
I recently had to replace my WRT54G and I decided on the E3200. I am satisfied with everything except the ability to RDP within my LAN between the wireless and wired computers. My setup is my primary PC is wired to my E3200 and a secondary PC and my laptop are using the wireless connection. Both of my wireless PC's are older and are utilizing the b/g connection. I have disabled the n connection for now. I also have two iPhones utilizing the wireless b/g connection.
I can RDP any computer from my primary(wired) PC. But when I try to RDP my primary PC from my wireless PC's(mostly my laptop) I can not get access. The error states "RDP can find the computer this means the computer may not belong to the network."
Finally, I was able to RDP seamlessly between the wireless and wired PC's with my old WRT54G without any problems at all.
View 4 Replies
View Related
Feb 22, 2013
I had the Linksys 3200 for almost a year and its been running great with my laptop. But now my laptop that connects to it by WIFI is getting these hiccups(what I call them), where it connects fine for a hour or 2. Then all of a sudden the WIFI icon on the laptop will say "limited internet access" and then no connection to the Linksys 3200. But other devices such as 2 smart phones, IPOD touch, Wii, and PS3 connects fine through the WIFI! Its been doing this for a few days. Thinking about doing a firmware upgrade for the E3200
View 9 Replies
View Related
Oct 5, 2011
Is it possible to connect the E3200 Router to the internet over the wifi (WLAN) interface?Actually I can only use the ethernet port called "Internet" to connect with my Fritz Box router (which is responsible for my internet connection to my DSL provider).But I don't want to use 10m or more ethernet cable across my flat so it would be nice to use just wifi.
View 5 Replies
View Related
Sep 23, 2012
I just installed an E3200 to replace my old Linksys. All my Nooks, IPADs, laptops and desktops are connecting wirelessly fine. However, I have 2 Wi Fi Radios that will pick up the network but will not connect and go into a network connect time out. One of the radios also has a hardwired connection and that is working fine. I have checked and double checked the network name, WPA key, etc. Of course I have reset all the radios and reenter new data many times, both manually and auto.
View 3 Replies
View Related
Aug 19, 2012
Buy new one Linksys E3200. Two day using and now have such problem. Every 30 minutes WiFi connection disappears for 10-15 sec. Then appear, but you can't connect to WiFi network for next 30 seconds. Update firmware of router to last version, but it doesn't work.
View 3 Replies
View Related
Jun 30, 2011
After recently intalling the WMP600N wireless adapter I have had great trouble getting it working properly.
Current performance
- signal: verygood/ excellent
- download speed: ~1mb
- upload speed: ~2mb
- signal speed: 18-54mbps (lots of variance but never above 54)
Comparison to my laptop
Laptop in same location with wireless G capability
- signal: verygood/ excellent
- download speed: ~20mb
- upload speed: ~2mb
- signal speed: 54mbps
my router is a D-Link wireless N router I recieved from my ISP. I do not believe my router is to blame for this problem since I have a laptop with an inferior wireless adapter recieving 20X the download speed.Drivers I have installed the latest drivers for windows 7 and I am running windows 7 Ultimate 64bit.
View 3 Replies
View Related
Oct 12, 2011
Hardware Software profile;
Laptop - Windows 7
Desktop - Vista Ultimate SP2
Router - Cisco Linksys E3200
Cables - CAT6
I am a sales engineer, so I use my desktop and laptop all the time. When on road, I sync my desktop with my laptop using a program called ViceVersa. This a very good, reliable syncing program that I have been using for over 10 years ( with upgrades ).
The program allows me to sync my desktop and laptop. The program also shows the data transfer rate during the syncing process. The typical data transfer speed is between 5MB/s and 10MB/s with sometimes up to 12MB/s. A typical sync between the computers will take about 3 - 5 minutes at the ~ 10 MB/s transfer rate using ethernet CAT6 cable inteface. At about 11pm last Tuesday,there was a Windows update on both my Vist and Win7 computers. On wednesday, I went to do a typical sync. The system has dramatically slowed to 59KB/s max. This is about 150 times slower than 5-10MB/s that I was used to for so many years. My typical sync was now taking about 2 hours....unacceptable ! I have tried everything to figure out what is going on and how to fix it but nothing has worked.
Then I tried to see what would happen if I disconnected my ethernet cable ( between the router and the laptop only ) and just sync using the wireless network. With that configuration, the transfer rate is ~ 2.5 MB/s which is not great but is much, much better than 59KB/s. I actually do not know what a reasonable wireless transfer rate should be since I never really did it before due to the faster speed of the wired configuration.
This is just a LAN. Only connecting my Desktop to my Laptop via the Cisco router.
How I can get my wired configuration back up to the 5-10MB/s transfer rate that it once was?
View 2 Replies
View Related
Jun 28, 2012
I upgraded from a E2000 to a EA4500 today and I am experiencing slow wired WAN speeds. On my E2000 I get approximately 60Mbps down and approximately 2Mbps up, and when switching over to the EA4500, I can only manage about 20Mbps down and about 2Mbps up. I can switch back and forth between routers and replicate the results every time
View 7 Replies
View Related
Feb 15, 2013
I have an E1200 acting soley as an AP. Everything works just fine, but when I try to copy files from one wired computer(both Windows 7) to another one on the same router(the E1200 in this case), the network utilization is only about 4%. If I take one of the computers off its wired connection and make it wireless, the utilization goes up to about 50%. Also if I take one of the compuyters off this router, and make a wired connection to my main router(which is connected via a wired connection to the E1200), the network utilization goes up to 50%.
View 3 Replies
View Related
Feb 15, 2012
Set up my new E4200V2 last night, everything appeared to be working but while streaming videos over wired LAN I get short hiccups over wired. While streaming videos, a few second long pause is really, distracting, this is a deal breaker and my previous router (DIR-655) had no issue streaming any videos. The wiring has not changed, only the router.I set up a ping between two wired linux boxes, and get: [code]
Whoa, 10 ms over gigabit LAN. This is crazy, but doesn't tell us much. The 10 ms was one out of hundreds of pings, so its only intermittent. This might explain the hiccups, but this router doesn't appear to log anything, so its hard to say.Next was scp transfers, which never exceed 15MB/s, in either direction. For gigabit, wired LAN this is awful, with my previous DIR-655 I would get at the very least 40 MB/s, in all situations.Next up, iperf. I set up iperf on the two hosts, and iperf reports reasonable gigabit speeds. [code] Tonight I am thinking of reverting to an old firmware, doing a hard reset and seeing if it persists, and if no ideas come up in this forum, it is getting returned, 15MB/s over gigabit lan is terribly broken.
View 5 Replies
View Related
Dec 6, 2012
I'm having an issue with my new E1200 routeur : I have a 100mbit/s connection and since i installed the E1200 , the speed is cut in half : Max 50 mbit/s .. ( or if this is an hardware limitation ? )
I have a gigabit network card with my pc , everything is fine on the pc / network side as i had these speed fine ( 100mbit/s ) with my old ISP router , ( wich i switched in bridge mode to use the E1200)
View 3 Replies
View Related
Apr 3, 2012
I have a problem with my download speed. I'm supposed to have a speed of 60 MBPS and when I collect my computer direct to the modem I received it but with my e2000 router, the 3 computer connected to it can't reach more than 30 MBPS. I just updated the firmware of the router to the newest version but nothing changed.
View 2 Replies
View Related
Jul 3, 2012
I have a problem with my new router. I connected't my iMac (27" 2010) and NAS Synology 1511. My problem is the slow connection between mac and router - only 100Mbit (ethernet port on mac is 1Gbit), strange thing... my NAS have 1Gbit with no problem, and the mac is not. I trying manual configure - forcing speed to 1Gbit, but then is no connection at all. I'm also trying changing wires, but no change. Im buying special ethernet cable cat 6 - also no change. Changing ports on router - result the same.
View 7 Replies
View Related
Aug 20, 2011
Yesterday, I changed my old belkin n1 router with Linksys WRT54GL router. Ever since them my upstream speed is really slow. I did the speedtest its like .5mbit. My downstream speed is just fine. This issue is only on wired computers, upstream speed on wireless computers is just fine.I retested router & modem several times, my upstream speed is normal when I connect cable directly from modem to my computer.Current Firmware Version is 4.30.14 build 5.
View 1 Replies
View Related
Apr 21, 2012
I saw one post recommending to changing the MTU from 1500 to 1400. That did absolutely nothing. My comcast internet is now slower than 14.4 dial up modem I had 16 years ago. The strange thing is I can sometimes download at over 2 mbps with torrents. It's mainly loading websites where the speed is so bad.
View 9 Replies
View Related
May 10, 2013
My WRT160N V3 halves my connection speed (5mbps to 2.7)with both wired and wireless. I have tried changing a lot of settings.
View 4 Replies
View Related
Mar 27, 2013
Region : Belgium
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 3.13.12 Build 120405 Rel.33996n
ISP : Telenet
I've just bought a TP-Link TL_WR1043ND and when I was configuring the wireless settings first I had a +- 40Mbps connection,a little later the connection dropped to 4Mbps and was constantly dropping the speed.Sometimes it went to 15Mbps and then it drops back to 4Mbps.Right now its only 1Mbps.
Configuration:
Wireless channel: 11
Mode: 11bgn mixed
Channel width: Auto
Max tx rate: 300Mbps
Wireless router radio and SSID broadcasting enabled
[code].....
View 1 Replies
View Related
