Linksys Wireless Router :: E3200 Slow Transfer Rate To Synology NAS
Jun 20, 2012
I just bought a synology NAS ds212j . I updated to DSM4.0. I purchased 2 Seagate ST2000DM001 Barracuda 7200RPM 2 TB SATA 6 GB/s NCQ 64 MB Cache 3.5-Inch Internal Bare Drive
My e3200 has the latest 1.0.04 firmware I'm backing up via time machine(mac book pro) in MAC 10.7.4 which has a wireless N card.
in Utilities (activity monitor)I'm only getting 9 megabytes per second , why is it so slow? I feel like it's taking forever. e3200 says it does up to 300 megabytes per second. any possible settings causing this?
a backup of 202 gigs has been running for about 4 hours and still going
View 9 Replies
ADVERTISEMENT
Dec 27, 2012
I have a home network running on a Linksys WAG320n and i have attached to it a WD MyBookLive (w Gigabit Ethernet). I am connected on the network via my Dell with a Intel(R) WiFi Link 5300 AGN. I am not able though to connect on N range. I have installed the latest drivers from Intel but nothing changed. When i try to copy a file from my computer to the WD Network drive the transfer rates are very slow. I get Max 2MB/s - 3MB/s while if i connect my computer with a wire the speed goes up by 3-4 times more.
View 5 Replies
View Related
Oct 12, 2011
Hardware Software profile;
Laptop - Windows 7
Desktop - Vista Ultimate SP2
Router - Cisco Linksys E3200
Cables - CAT6
I am a sales engineer, so I use my desktop and laptop all the time. When on road, I sync my desktop with my laptop using a program called ViceVersa. This a very good, reliable syncing program that I have been using for over 10 years ( with upgrades ).
The program allows me to sync my desktop and laptop. The program also shows the data transfer rate during the syncing process. The typical data transfer speed is between 5MB/s and 10MB/s with sometimes up to 12MB/s. A typical sync between the computers will take about 3 - 5 minutes at the ~ 10 MB/s transfer rate using ethernet CAT6 cable inteface. At about 11pm last Tuesday,there was a Windows update on both my Vist and Win7 computers. On wednesday, I went to do a typical sync. The system has dramatically slowed to 59KB/s max. This is about 150 times slower than 5-10MB/s that I was used to for so many years. My typical sync was now taking about 2 hours....unacceptable ! I have tried everything to figure out what is going on and how to fix it but nothing has worked.
Then I tried to see what would happen if I disconnected my ethernet cable ( between the router and the laptop only ) and just sync using the wireless network. With that configuration, the transfer rate is ~ 2.5 MB/s which is not great but is much, much better than 59KB/s. I actually do not know what a reasonable wireless transfer rate should be since I never really did it before due to the faster speed of the wired configuration.
This is just a LAN. Only connecting my Desktop to my Laptop via the Cisco router.
How I can get my wired configuration back up to the 5-10MB/s transfer rate that it once was?
View 2 Replies
View Related
Mar 23, 2013
I've just bought a Synology DiskStation DS412+ and put 2 x 3TB Western Digital Red drives in it, set up in RAID 0. It's currently plugged in to my gigabit Netgear switch.I created a user with full permissions on the NAS, created a share, mapped a drive on my Windows 7 PC (also gigabit ethernet) and tried copying some files, but I'm getting painfully slow transfer speeds (< 40KB/s - yes, kilobytes, it's not a typo!
Does anyone have any ideas why it'd be so slow? There's loads of reports online of people getting > 80MB/s from this NAS.
I've copied files from this PC to my MacBook Pro in the past and got decent enough speeds so it shouldn't be an issue with the NIC on this PC, or (hopefully) the Netgear switch it's going through.
View 1 Replies
View Related
Feb 19, 2013
I have 4 - WAP 321's in an office all connected to a POE gigabit switch. Each WAP shows connected at 1GB but when I am sitting within a couple feet of the WAP and attempt to transfer a 972MB file it takes around 9 minutes to complete. speeding this up? All 4 AP's are setup as a cluster as well.
View 1 Replies
View Related
Jan 11, 2012
My E3200 is set up with no encyrption/ security. The 5GHZ band is set to wireless N, channel width is set to Auto (20 or 40) channel is also set to auto. I have my 2 laptops connected on the 5GHZ band and both have excellent connection with 300mbps. I'm transfering some files between the 2 and an only getting 7MB (so ~56mbps). Both laptops are running windows 7 ultimate.
I've tried transfering music, videos, and some ISO's.
View 5 Replies
View Related
Jul 20, 2011
i have a 4Mbps DSL internet connection with 3 PCs connected through a router. 2 are connected wirelessly and the other is wired via an ethernet cable. i noticed that when downloading a file from an international server, the transfer rate on the wireless PCs is 2-3 times slower than on the wired PC. the wireless PC would get about 150-200kb/s, whereas the wired PC can max out to 450kb/s on a single download. however when i download from a local or nearby server instead, the transfer rate on the wireless and wired PCs are the same and can both reach up to 450kb/s per download. i don't understand why the wireless connection is slower to international servers compared to the wired PC.my wireless signal is at 54Mbps with "excellent" strength. i also tested the ping results from both the wireless and wired PCs to international servers and they are pretty much the same.
- all PCs are running windows XP SP3
- the modem/router is a D-Link 2640B
View 6 Replies
View Related
Aug 2, 2012
I'm using Pix 501 with firmware: Version 6.3(3)I have problem with Pix 501:
+ transfer rate data between interface outside and inside very slow, even between 2 interface inside.
+ I have test file transfer between 2 PC connect via interface inside.
+ Results transfer 1 file 1MB with total time 60s
I don't upgrade software current from 6.3(3) to 6.3(5) via TFTP. It's error Please see attach file.
View 2 Replies
View Related
Dec 11, 2011
So I have a really neat computer sitting here, 2500K, P8z68-v, samsung 830 64gb ssd, corsair vengeance 16gb, deskstar hdd, firepro v5800
I have a non-descript trendnet 56K v.92 dial up modem installed to pci slot1 on my mobo.The phone company says they can't get a quicker connection than 31.2 Kbps established to dial up users in this area.The real issue is the data transfer rate.I have seen it reach as high as 6.xx Kbps but generally hovers around 2.5 Kbps.Now it is down to 1.xx Kbps and I took the last 48 hours downloading all the updates for windows and several other updates for hard ware etc.Now I need the ATI firepro update and 114 Mb will take over 16 hours at my average speed, and some 32 hours at the new slower speed
View 17 Replies
View Related
Jul 30, 2011
Which Intel network cards runs well with E4200 (latest FW)? I mean good connection and transfers rate. I have two clients with the same cards (Intel 4965agn, latest driver) and I got transfer rates at 144 Mbps with both radios working (2.4 and 5GHZ on the E4200). When I try to use 5Ghz only it drops to 54 Mbps and for 2.4Ghz it drops for 130 Mbps. Could I reach better transfers rate with a Intel 4965agn card (300 or 450 Mbps)?
View 4 Replies
View Related
Jun 29, 2011
My transfer speed from HDD which connected to linksys e4200 reach max 2,3MB/s how it is possible to watch fullHD movie if its required minimum 5MB/s? Maybe I should make some adjustments? HDD-WD My Passport 750Gb Also connection speed max reach 144mb/s?? how to make 300mb/s ? wifi adapter is Intel advanced N + WiMax 6250 AGN last driver installed, also E4200 last firmware installed 1.0.0.2 all settings by default Max download speed 75Mb/s by utorrent but provider gives 100Mb/s By cable its ok, max speed 100Mb/s as giving provider
View 9 Replies
View Related
May 21, 2011
E4200 with an external hard drive WD My Book (1TB) connected to the router via USB.Desktop PC (Windows 7) connected to router via Ethernet cable.Laptop PC (Windows 7) connected to router via wireless connection.I wanted to create a central media (videos/pictures) file on the external hard drive connected to the router. However, the transfer rate is terribly slow. Interestingly, it is 50KB/second when copying from the Desktop (via Ethernet) and 1.6Mbps when copying from the Laptop via wireless.
View 9 Replies
View Related
May 19, 2012
I have a E3200 Router and when the computers are connected directly to router (Wired) the speed is SLOW and when computers are connected via wireless the speed is fast (normal). What can i do to have the wired computer with same fast speed as wireless?....i'm i missing something?Here are the speed results:
All wired computers connections (total of 4) downwload speed ranging from 8 Mbps to 13 Mbps.
All wireless computer connections download speed stable at 49 Mbps.
View 2 Replies
View Related
Feb 13, 2012
Ok, so I recently upgraded to a Linksys E3200. I am trying to get the QoS to work properly. I know that it is supposed to prioritize network traffic, so that if I have busy traffic but I am playing an online game, it should keep my gaming from stuttering while slowing other traffic down.
The problem is that every time I enable QoS everything slows down dramatically. I had a 200MB download that was going to take 5hrs with QoS enabled, that took 10min with QoS disabled. And with QoS enabled I can't even watch a youtube video without it pausing to buffer every 10 seconds. And that was the only PC/device using the network at the time. Again turning off the QoS WMM option solved the problem. I have noticed this problem with multiple routers and brands and usually just disable QoS as soon as I set up a router, however I heard that I won't get the full benefit of 300Mbps without QoS enabled.
I don't have any special Voice over IP needs, or video streaming etc. and I rarely am using multiple network devices at the same time. Is there really any reason I should enable QoS? Also I never really play with the settings for QoS, I just figure that since it comes enabled by default it should work for the average consumer.
View 9 Replies
View Related
Nov 9, 2012
Each time I'm rebooting my E3200 device my ping to my ISP is 20ms. Few hours later the ping goes up to 300-500ms.Than I reboot again and the ping is going down to 20ms again.
View 5 Replies
View Related
Oct 18, 2011
Using 1.0.03.
I am seeing something pretty bizarre: when trying to copy files between two computers (both Windows 7 SP1 64bit), both physically plugged into the back of the E4200, I see extremely slow transfer speeds: 1.0-1.1 MB/sec. Both computers are fast (i7-2600K, both using SSDs) and both have gigabit ports (and the 4200's web UI shows both ports in question as operating in gigabit mode).
This is so slow as to be sort of funny. Each of these computers see speeds well in excess of that when transferring between the computer and outside internet sites...so it's kind of funny that two computers plugged into the same switch in the back of the 4200 see 1 MB/second.
View 6 Replies
View Related
Aug 26, 2011
I have 8mbs down/1 mbs up service through a cable modem (WOW). We've been using a WRT320N wireless router with great success. I haven't checked true transfer rates, but when I do a speed test (url...), I pretty consistently get the speeds we are paying for. There's a room I wanted to use as an office but the signal didn't reach there. I just set up a WRE54G range expander. It is talking to the router and my compter. I have internet access but the speeds are considerably slower (<1mbs down/<0.4 mbs up) than what I get on the other computer that's talking directly to the router. I've looked for specs on data rates on the WRE54G and can't find them, but I can't image they're that slow. Can this be because I'm using a G expander with an N router?
View 1 Replies
View Related
Nov 20, 2011
i have a newly formatted (i.e. empty) 2TB WD my book elite which when i connect it to my computers usb port, can transfer a 6gb video file at over 100MB/s according to the win 7 detail box. However, when i connect it to the usb port on the back of the e4200 and try to transfer the same file, it only goes at 8MB/s max ... it appears to be going at usb 1 speed. i've got the latest firmware on both the e4200 and the my book 1111 and everything seems to be working fine for both, except this transfer rate when connected to the e4200.granted, cisco doesn't specifically list this drive as being tested, but the router does recognize it and shows it as usb 2.0, but yet the transfer speed is just too slow.8MB/s is just not workable...i could just connect the drive directly to the computer and share it that way, but connecting it to the e4200 was one of the reasons i bought the e4200.
View 8 Replies
View Related
Jul 11, 2011
I'm having very slow file transfer speeds between the 2 computers on my network. One is a gigabit pc wired (cat6) to the e3000. The other is a wireless N laptop. Both computers running Win7. Speeds are like 1.5 - 2 MB/s. when I connect the laptop to the router with a cable (cat6) I get proper high speed. Trying to figure out if it's a problem with the router or windows or what. Speedtest.net says I'm getting 16 MB/s DL wirelessly to my laptop. Shouldn't wireless N be capable of higher speeds than 1.5 MB/s?? Tests are done approx 10 feet from the router.
View 1 Replies
View Related
Jul 3, 2012
Transfer speed for sending or receiving files from a USB external HDD connected to the router is slow? Speed ranging from 2MB - 4MB/s. The HDD is definitely capable of at least 80MB/s if plugged directly into the PC. Is it meant to be this slow or there's a fix somewhere which I'm not aware of? Thought it's suppose to be the top of the line products but seems so inferior if I were to compare with other high end routers in the market which performs better, faster and definitely much cheaper.
View 9 Replies
View Related
Mar 24, 2012
I have recently purchased a Cisco E4200 to replace my D-LINK DIR-655, which I thought was defective because I was getting slow wirless file transfer speed, regardless of setting, location and client.Using the E4200, when I transfer a file from a PC to another, both connected at 300mb on the 2.4ghz band, the file transfer rate reported by windows 7 and networx is from 2MB/s to 3.5MB/s. I think those transfer rates are not acceptable. Is that a good assumption ? I would expect something in the range of 10MB/s (which is what I get with a cheap dlink router, wired)
I also had great difficulty finding a channel. I had to try them all one-by-one as the auto channel selection made my PCs connect at 130mb.The E4200 is setup as follows:
-WPA-Personal
-Channel 5
-802.11n only
I have tried 3 different computers with different network adapters and they all underperform (IMO..).There are no other wireless networks in my area.I also took the E4200 to my office which is very crowed. Every single channel is occupied by several wireless networks. I get a file transfer speed PC to PC of about 2MB.I basically could have kept my DIR-655 as the speeds are identical.
View 4 Replies
View Related
Nov 12, 2012
Why my E3200 is (for lack of a better word) "throttling" my internet speeds.I'm signed up for my ISP's 50Mbps data plan. When I hook up my laptop directly to the cable modem (via LAN cable), I see close to 50Mbps as the internet speed (measure via speedtest.net). When I hook up my router to the cable modem, and connect via LAN cable to the router, the internet speed comes down to around a maximum of 26Mbps. NOTE, that I am still talking about a wired connection and not a wireless access. Speed tests with the wireless access do yield the same results as well. To rule out the obvious, I've confirmed that there aren't any other devices on the network and no other bandwidth hogging applications running while I performed these tests.
View 9 Replies
View Related
Jul 21, 2011
I have a home network with a media center. I have the hauppauge 1212 HD pvr so that I can record video in HD to my hard drive. I want to stream this content to the differnet PCs on my home network. Every TV in my home I have hooked an HTPC to it. I use them to play dvd's. Stream netflixs etc. My problem is that I am getting a terrible transer rate wirelessly. 600 -750 kbps. (tested by transfering large files from pc to pc) All computers have 300Mbps wireless n cards. all are recieving max signals. There are either 3 or 4 pc's connected at a time depending on whether my laptop is connected or not. Obviously this is way to slow to stream video. Made sure my network name is unique. changed to wireless channel 1 I do think I have WEP 64bit encription could this be an issue?
View 7 Replies
View Related
Jan 17, 2011
Very slow transfer speeds problem with this router. When I put the router in the system, my transfer speeds drop from 12 Mbps to 3 Mbps. I've updated the firmware to the latest version but that doesn't work. The most frequent suggestion is to upgrade the firmware which I have already done.
View 5 Replies
View Related
Mar 3, 2011
I have two machines that both have WUSB600N wireless network adaptors with a Cisco WRT160N router. The file transfer speeds between the two devices maxes out at 1.6Mbs. If I run speed tests off the internet I hit 15 to 20 and downloads are excellent. I have played with all kinds of settings for the driver and router but nothing seems to work. Both these devices are running Windows 7. I tried a file transfer with an XP device as well and it maxes at about 1.6. how to increase the bandwidth??
View 1 Replies
View Related
Feb 10, 2011
just bought a WD my book world edition 2 NAS and have been trying to tranfer files wirelessly to it but a 700mb file is taking 25mins to trans. my book is connected by ethernet to netgear dgnd3300 router and my laptop has sitecom 300n usb doongle.is there some sort of setting i've missed or is this speed normal?
View 5 Replies
View Related
Oct 23, 2011
How to increase data transfer speed on lan
View 2 Replies
View Related
Feb 17, 2013
I have a couple laptops in my home and just purchased a WD network drive so that a central location can keep all our media files (photos, videos, etc.) and we can access it with our pc's, phones, and tablets. I'm in the process of setting up the HD and transferring all the media to the drive wirelessly however I'm only experiencing about 1.5MB/s-4MB/s. Is there a way to speed this up.
View 2 Replies
View Related
May 11, 2012
We have a small home office with three computers, two new comps with win7 64 and an old comp running Vista32. Up until last week, the two 7's accessed files on the vista machine via a public folder, and everything was peachy, speed-wise. Trashed the vista this week and replaced it with a new desktop running win7 64. I backed up the old comp's files on the new comp, set up the new win7 home network, and everything went to hell. Both of the 'old' win7 machines can access files on the new, but the speeds are unbearable. It takes, literally, over 10 minutes for Accubid to load (accessing files on the new desktop), whereas it was pretty much immediate before. Quickbooks freezes for a minute and a half before it finally connects. A 60mb PDF file takes two minutes to copy. It even hiccups when I save a freakin' Word document. After some research I found that window's new home sharing network kinda sucks, so I turned it off on all machines and mapped network drives. Nothing.turn off remote differential compression, so I turned it off on all machines. Nothing. I disabled flow control on all machines. Nothing.The weirdest thing I did - I disabled auto-tuning and restarted all computers. I then opened Accubid and it opened immediately! I restarted the program 6 or 7 times, and each time it came up within seconds. I was ecstatic. Then my boss came in 5 minutes later and I opened Accubid to show him I finally fixed it. It took 10 minutes to load again, and I haven't been able to repeat whatever I had done since.
My ISP is ATT.
Modem - D-Link DSL 520B
Router - Netgear WNDR3800
Network is wired. Again, access to internet is blazing. Access to the computer 6 feet away from me is not.
View 3 Replies
View Related
Apr 6, 2012
Which network provides the highest data transfer rate?
View 1 Replies
View Related
Nov 26, 2009
I have the above router, but I have noticed that the USB Transfer speed is very poor. I have a WD External HD plugged into the router and id i transfer filed from my server which is hardwired to the router I only get a transfer speed of about 2.5MB/s.
For a USB device I was kind of thinking I would be getting a minumm of atleast 50-60MB/s.
View 9 Replies
View Related
Apr 18, 2012
I have a computer connected to a Switch3750G and another computer connected to another Switch3750G. Theses switches are connected through a Optical Fiber link in the uplinks of the boths Switchs 3750. The computers are connected in the access ports, this ports works at 1Gbps. My question is Which is the maximum transfer rate that should reach between these two computers.
View 2 Replies
View Related
Nov 23, 2011
RV110W connected to ISP via PPPoE. MTU is default setting - 1492. IPSs tarif - 100 Mbit/sec IN, 40 Mbit/sec-OUT.When the laptop is connected to RV110w via ethernet the data transfer rate is 45 Mbit IN / 25 Mbit OUT.When a laptop is connected to ISP directly without a router a data transfer rate is 95 IN / 35 OUT.
View 0 Replies
View Related
