Linksys Wireless Router :: Intel 4965agn Client With E4200 - Good Connection / Transfer Rate?
Jul 30, 2011
Which Intel network cards runs well with E4200 (latest FW)? I mean good connection and transfers rate. I have two clients with the same cards (Intel 4965agn, latest driver) and I got transfer rates at 144 Mbps with both radios working (2.4 and 5GHZ on the E4200). When I try to use 5Ghz only it drops to 54 Mbps and for 2.4Ghz it drops for 130 Mbps. Could I reach better transfers rate with a Intel 4965agn card (300 or 450 Mbps)?
View 4 Replies
ADVERTISEMENT
Feb 17, 2012
Recently purchased a Linksys E4200.Computers on network:Two hard-wired gigabit desktops: one Windows XP, one Windows 7One hard-wired 100mbps desktop running Windows 7One laptop with an Intel 4965AGN running Windows 7.File transfer rates between any of the desktops and the laptop is very slow: ~2 megabytes/s
File transfer rates between the gigabit desktops is good (~50 megabytes/s, hdd bottleneck), transfers between the 100mbps desktop and one of the gigabit machines gives ~10 megabytes/s.Currently running on the 5Ghz band, connected with N at 300 megabits, good signal strength. Disabled mixed mode on this band, enabled N-only.Use a scanner tool, I can tell that there are no other networks on 5Ghz band.Also, tried 2.4 Ghz band and got similiar low speeds.These transfer rates are much below what other people report for real-world throughput. Any ideas? I know there is an Advanced Wireless config page, is there a setting there that might work if adjusted?
View 1 Replies
View Related
Dec 27, 2012
I have a home network running on a Linksys WAG320n and i have attached to it a WD MyBookLive (w Gigabit Ethernet). I am connected on the network via my Dell with a Intel(R) WiFi Link 5300 AGN. I am not able though to connect on N range. I have installed the latest drivers from Intel but nothing changed. When i try to copy a file from my computer to the WD Network drive the transfer rates are very slow. I get Max 2MB/s - 3MB/s while if i connect my computer with a wire the speed goes up by 3-4 times more.
View 5 Replies
View Related
Jun 20, 2012
I just bought a synology NAS ds212j . I updated to DSM4.0. I purchased 2 Seagate ST2000DM001 Barracuda 7200RPM 2 TB SATA 6 GB/s NCQ 64 MB Cache 3.5-Inch Internal Bare Drive
My e3200 has the latest 1.0.04 firmware I'm backing up via time machine(mac book pro) in MAC 10.7.4 which has a wireless N card.
in Utilities (activity monitor)I'm only getting 9 megabytes per second , why is it so slow? I feel like it's taking forever. e3200 says it does up to 300 megabytes per second. any possible settings causing this?
a backup of 202 gigs has been running for about 4 hours and still going
View 9 Replies
View Related
Jan 2, 2010
I installed an Intel 4965AGN into my Dell Inspiron (running Windows 7) to connect with 802.11n to my D-Link DIR-655. It refuses to connect in N mode, it will only connect in G mode. I have tried everything I could find online. I set security to WPA2-AES, and even tried with no security with no luck whatsoever. Before the 4965AGN i had an Intel 5300 which had the same problem, but I returned it because I thought it was a problem with compatibility with my Dell. Apparently something else is the culprit. What could I be over-looking?
View 9 Replies
View Related
Aug 20, 2011
I have searched on the problem as much I as I can to no eval, I can not get the Intel 5300 on a Lenovo T400 to connect at N on either radio
I tried evey combination of settings possible on the E4200 and on the 5300 Which was a lot of combinations I can only get the a G connection on 2.45ghz and only an A on the 5ghz
To make things worse, trying to call Lenovo is pointless without a warrenty they wont even answer simple questions without out it, totally insane!
View 2 Replies
View Related
Jun 29, 2011
My transfer speed from HDD which connected to linksys e4200 reach max 2,3MB/s how it is possible to watch fullHD movie if its required minimum 5MB/s? Maybe I should make some adjustments? HDD-WD My Passport 750Gb Also connection speed max reach 144mb/s?? how to make 300mb/s ? wifi adapter is Intel advanced N + WiMax 6250 AGN last driver installed, also E4200 last firmware installed 1.0.0.2 all settings by default Max download speed 75Mb/s by utorrent but provider gives 100Mb/s By cable its ok, max speed 100Mb/s as giving provider
View 9 Replies
View Related
May 21, 2011
E4200 with an external hard drive WD My Book (1TB) connected to the router via USB.Desktop PC (Windows 7) connected to router via Ethernet cable.Laptop PC (Windows 7) connected to router via wireless connection.I wanted to create a central media (videos/pictures) file on the external hard drive connected to the router. However, the transfer rate is terribly slow. Interestingly, it is 50KB/second when copying from the Desktop (via Ethernet) and 1.6Mbps when copying from the Laptop via wireless.
View 9 Replies
View Related
Oct 18, 2011
Using 1.0.03.
I am seeing something pretty bizarre: when trying to copy files between two computers (both Windows 7 SP1 64bit), both physically plugged into the back of the E4200, I see extremely slow transfer speeds: 1.0-1.1 MB/sec. Both computers are fast (i7-2600K, both using SSDs) and both have gigabit ports (and the 4200's web UI shows both ports in question as operating in gigabit mode).
This is so slow as to be sort of funny. Each of these computers see speeds well in excess of that when transferring between the computer and outside internet sites...so it's kind of funny that two computers plugged into the same switch in the back of the 4200 see 1 MB/second.
View 6 Replies
View Related
Nov 20, 2011
i have a newly formatted (i.e. empty) 2TB WD my book elite which when i connect it to my computers usb port, can transfer a 6gb video file at over 100MB/s according to the win 7 detail box. However, when i connect it to the usb port on the back of the e4200 and try to transfer the same file, it only goes at 8MB/s max ... it appears to be going at usb 1 speed. i've got the latest firmware on both the e4200 and the my book 1111 and everything seems to be working fine for both, except this transfer rate when connected to the e4200.granted, cisco doesn't specifically list this drive as being tested, but the router does recognize it and shows it as usb 2.0, but yet the transfer speed is just too slow.8MB/s is just not workable...i could just connect the drive directly to the computer and share it that way, but connecting it to the e4200 was one of the reasons i bought the e4200.
View 8 Replies
View Related
Feb 21, 2013
i have configured some 1142n's, everything works in terms of .n but the reported client connection on the AP does match the published MCS definitions.eg so what does "Current Rate (Mb/sec) m6-4" actually mean in terms of MCS connection
View 3 Replies
View Related
Mar 24, 2012
I have recently purchased a Cisco E4200 to replace my D-LINK DIR-655, which I thought was defective because I was getting slow wirless file transfer speed, regardless of setting, location and client.Using the E4200, when I transfer a file from a PC to another, both connected at 300mb on the 2.4ghz band, the file transfer rate reported by windows 7 and networx is from 2MB/s to 3.5MB/s. I think those transfer rates are not acceptable. Is that a good assumption ? I would expect something in the range of 10MB/s (which is what I get with a cheap dlink router, wired)
I also had great difficulty finding a channel. I had to try them all one-by-one as the auto channel selection made my PCs connect at 130mb.The E4200 is setup as follows:
-WPA-Personal
-Channel 5
-802.11n only
I have tried 3 different computers with different network adapters and they all underperform (IMO..).There are no other wireless networks in my area.I also took the E4200 to my office which is very crowed. Every single channel is occupied by several wireless networks. I get a file transfer speed PC to PC of about 2MB.I basically could have kept my DIR-655 as the speeds are identical.
View 4 Replies
View Related
Feb 19, 2013
I have 4 - WAP 321's in an office all connected to a POE gigabit switch. Each WAP shows connected at 1GB but when I am sitting within a couple feet of the WAP and attempt to transfer a 972MB file it takes around 9 minutes to complete. speeding this up? All 4 AP's are setup as a cluster as well.
View 1 Replies
View Related
Mar 20, 2013
I have ten E4200 routers deployed in five library branches. In recent months, the E4200's in two branches have occasionally gone into a state where they are not always providing an IP address to both wired and wireless devices. Some devices will get an IP fine and others will not, The problem seems to move and the next day the same device will connect fine and others will not. A reset of the router usually clears the problem but it is becoming more frequent and bothersome. For some reason only two locations are effected.
Some notes:
- Firmware version is 1.0.02 build 13
- When I set devices up with static IP's they work fine, so the problem seems to be related to the DHCP service
- The WAN side of the network tests fine with no issues
- I've had these routers deployed for over a year and this problem just started in the past two months
- Routers and AP's are on different channels to prevent interference
- No nearby WiFi signals appear to be casuing any interference
View 3 Replies
View Related
Mar 10, 2012
I've assigned an ip address to my htpc using dhcp reservation. On my old router I could use the client name, for instance: ssh name@clientName Instead of: ssh name@ipAddress Currently I cannot do this with the stock cisco firmware (unless I'm mistaken). Is there something I have to do to get it working? Or do I have to resort to tomatoUSB/WRT.
View 1 Replies
View Related
Oct 29, 2011
I just purchased an E4200 router. I have four clients on my network and they are all set up for DHCP. I renewed their IPs and they all are connected. "Cisco Connect" reports that I have four clients connected. When I access the router and bring up the DHCP Client Table, there are no entries. There should be four entries. Aftern I enable the logging function, none of the logs have any data in them even after I wait for 45 minutes and use the internet and renew IPs. I am using Firmware Version: 1.0.03. I have the same results for both Chrome and Firefox. I want to be able to set Static IPs but I am hampered by the not having any clients in the DHCP client table.
View 9 Replies
View Related
Jun 9, 2012
When I enable IPv6 on my E4200, the Windows 7 DHCP client crashes. It also seems to crash the audio service, the event logger and a few other windows services.
View 9 Replies
View Related
Dec 14, 2011
I have had an e4200 for about a month now and its been pretty good. But I have noticed that it completely locks up when I go to copy mass amounts of data through it. I have a NAS drive plugged into it and my laptop is on the 2.4 spectrum. I went to transfer 8gigs of data from laptop to NAS drive and the entire wireless portion of the router locks up. All my wireless clients drop and I have to unplug the router and plug it back in. Even the 5ghz clients drop as well. I have not tried hardwire, but the main reason I got this was for its throughput.
View 1 Replies
View Related
Jul 15, 2011
One of the many things that I liked about the e4200 over my olg 54GL was the fact that I could reboot it remotely. However, I've recently had a few problems that only a full power down would fix. In addition, I've noticed that the DCHP client table doesn't reset when I do a soft reboot. Is this intentional? Is the soft reboot not really a full reboot? Can it be made a real reboot?
View 7 Replies
View Related
Oct 23, 2011
How to increase data transfer speed on lan
View 2 Replies
View Related
Feb 17, 2013
I have a couple laptops in my home and just purchased a WD network drive so that a central location can keep all our media files (photos, videos, etc.) and we can access it with our pc's, phones, and tablets. I'm in the process of setting up the HD and transferring all the media to the drive wirelessly however I'm only experiencing about 1.5MB/s-4MB/s. Is there a way to speed this up.
View 2 Replies
View Related
May 11, 2012
We have a small home office with three computers, two new comps with win7 64 and an old comp running Vista32. Up until last week, the two 7's accessed files on the vista machine via a public folder, and everything was peachy, speed-wise. Trashed the vista this week and replaced it with a new desktop running win7 64. I backed up the old comp's files on the new comp, set up the new win7 home network, and everything went to hell. Both of the 'old' win7 machines can access files on the new, but the speeds are unbearable. It takes, literally, over 10 minutes for Accubid to load (accessing files on the new desktop), whereas it was pretty much immediate before. Quickbooks freezes for a minute and a half before it finally connects. A 60mb PDF file takes two minutes to copy. It even hiccups when I save a freakin' Word document. After some research I found that window's new home sharing network kinda sucks, so I turned it off on all machines and mapped network drives. Nothing.turn off remote differential compression, so I turned it off on all machines. Nothing. I disabled flow control on all machines. Nothing.The weirdest thing I did - I disabled auto-tuning and restarted all computers. I then opened Accubid and it opened immediately! I restarted the program 6 or 7 times, and each time it came up within seconds. I was ecstatic. Then my boss came in 5 minutes later and I opened Accubid to show him I finally fixed it. It took 10 minutes to load again, and I haven't been able to repeat whatever I had done since.
My ISP is ATT.
Modem - D-Link DSL 520B
Router - Netgear WNDR3800
Network is wired. Again, access to internet is blazing. Access to the computer 6 feet away from me is not.
View 3 Replies
View Related
Apr 6, 2012
Which network provides the highest data transfer rate?
View 1 Replies
View Related
Nov 22, 2011
My dad recently got a E4200 router, My whole family are mac users, the connection are all okay with their computers, I'm the only one using Microsoft, ASUS running on Vista. The connection is fine when I'm near the router, but when I go to my room I get no connection at all, it connects for a second but then it goes on connection with limited access.
View 5 Replies
View Related
Mar 21, 2012
Last week I bought the E4200 thinking it was probably the best router on the market and if it worked properly, it would be...I think.I have attached a Seagate GoFlex Desk 2Tb USB drive formatted to NTFS to the USB of the E4200. I can map to it from my Windows XP computer with no problem and I can FTP to it from any browser...my Windows 7 machine is another story. When I try to map the network drive from the Windows 7 machine I get error code 0x80070035 every time. I've seen some other threads where people are having this problem but in the cases I've found, they aren't getting any connection via XP or FTP either.
View 2 Replies
View Related
Jan 29, 2012
I have just installed Cisco Connect v1.4 (11266.0), and have upgraded my E4200 software to 1.0.03.I want to add a USB printer connected to the router but when I open Cisco Connect, and select the "Add new devices.....' button, the only option for a printer is 'Wireless Printer' not 'Printer' followed by USB or Wireless as per the User guide.
View 9 Replies
View Related
Apr 18, 2012
I have a computer connected to a Switch3750G and another computer connected to another Switch3750G. Theses switches are connected through a Optical Fiber link in the uplinks of the boths Switchs 3750. The computers are connected in the access ports, this ports works at 1Gbps. My question is Which is the maximum transfer rate that should reach between these two computers.
View 2 Replies
View Related
Nov 23, 2011
RV110W connected to ISP via PPPoE. MTU is default setting - 1492. IPSs tarif - 100 Mbit/sec IN, 40 Mbit/sec-OUT.When the laptop is connected to RV110w via ethernet the data transfer rate is 45 Mbit IN / 25 Mbit OUT.When a laptop is connected to ISP directly without a router a data transfer rate is 95 IN / 35 OUT.
View 0 Replies
View Related
Jan 2, 2013
I have an E4200 (v1) with the latest firmware. For some reason, the E4200 does not allow me to conenct to certain websites. This is true for wired or wireless connections.To test, I connected a wired PC directly to my cable modem and was able to connect to all websites fine. I also tried an old D-Link router I had on hand and was able to connect to all sites fine. Went back to the E4200 and was blocked. I re-loaded the firmware and same results.
View 4 Replies
View Related
Apr 21, 2012
I have my e4200 connected to another modem/router (2Wire 3600HGV), because the other router does not support Wireless N. I can connect to my E4200 network, but there's just no connection to the internet. I reseted my e4200 but still no luck. I've unplugged both routers and replugged them, nothing. I know it's possible because I've had it set up before but I had my 2Wire exchanged for a newer one.
Firmware: 1.00.4
Just to be sure. I have the cable going from my modem out of port #1 and into my e4200 where it says internet, thats correct, right? On my e4200 i have the IP 192.168.1.2 but on the 2Wire I have the e4200 as 1.92.168.1.66.
View 1 Replies
View Related
Nov 7, 2011
The web site says that the E4200 has a USB port to connect USB drives and printers. That sounded to me like multiple devices could be added. It says nothing about only being able to connect one. Since I have 3 USB drives and 2 USB printers, that sounded great. Setting it up, it seems that this port will not use a HUB, and can only be used for one USB device. How can that be? That is so limiting as to be nearly useless.
View 3 Replies
View Related
Jul 20, 2011
i have a 4Mbps DSL internet connection with 3 PCs connected through a router. 2 are connected wirelessly and the other is wired via an ethernet cable. i noticed that when downloading a file from an international server, the transfer rate on the wireless PCs is 2-3 times slower than on the wired PC. the wireless PC would get about 150-200kb/s, whereas the wired PC can max out to 450kb/s on a single download. however when i download from a local or nearby server instead, the transfer rate on the wireless and wired PCs are the same and can both reach up to 450kb/s per download. i don't understand why the wireless connection is slower to international servers compared to the wired PC.my wireless signal is at 54Mbps with "excellent" strength. i also tested the ping results from both the wireless and wired PCs to international servers and they are pretty much the same.
- all PCs are running windows XP SP3
- the modem/router is a D-Link 2640B
View 6 Replies
View Related
Aug 2, 2012
I'm using Pix 501 with firmware: Version 6.3(3)I have problem with Pix 501:
+ transfer rate data between interface outside and inside very slow, even between 2 interface inside.
+ I have test file transfer between 2 PC connect via interface inside.
+ Results transfer 1 file 1MB with total time 60s
I don't upgrade software current from 6.3(3) to 6.3(5) via TFTP. It's error Please see attach file.
View 2 Replies
View Related
