Linksys Wireless Router :: 9000 - Can't Ping External IP
Aug 15, 2011
I'm looking to setup a few ip security cameras in my house and would like to monitor from work. The first thing I did was give the ip camera a static ip on my local LAN 192.168.1.104. I also forwarded port 9000 to this ip. I then went to [URL] to look up my external ip address. I was able to obtain one ip for my router and another for my modem (disconnected router and went direct through modem).
I've since tried to ping my router WAN ip from work numerous times via http://24.x.xxx.xx:9000 and I get timeout errors. I've tried traceroute and it gets close, but times out the last 3 hops. I've had Comcast on the phone many times trying to resolve and needless to say they weren't able to work.
View 6 Replies
ADVERTISEMENT
Feb 1, 2011
I am trying to setup an RV016 router to do "1 to 1 NAT". I am starting with setting the external IP address of my RV016 to 10.8.58.219 on the WAN1 port, and LAN IP 10.10.20.254. Simple enough. When I connect my laptop to port1 on the router's LAN side I can ping the router's external AND internal IP addresses fine; But I can not ping from outside when connected through WAN1 port.I am performing a simple local test with an external hub, I put a patch cable from WAN1 port to the hub, another patch cable from port 1 on LAN side to the same hub, and from my laptop to the hub. When I use my laptop's IP address with the internal schema (10.10.20.100 for example) I can ping both WAN1 and LAN IP's; but when I use on my laptop the external IP schema (10.8.58.100 for example) I can not ping it. Therefore is not working when I connect my router to the real network.I went into the web setup pages of the router and dissabled: firewall and basicaly all security "blocks" it has, and leave it open for my testing.
View 1 Replies
View Related
Jul 29, 2012
I am in a small office and we have a Buffalo NAS being used. Configuring it was fairly easy, but recently it just stop letting us have web access. My External and Internal Ports were 9000, but for some reason now my router will not even show that there is a 9000 port and even if I port forward it. It does no good what good possibly be keeping this port invisible after it was being used the last couple of months. I called my cable company and they said they are not blocking it. But right now I cant access the server from a remote location.
View 4 Replies
View Related
Mar 12, 2012
Have a E4200 with version 1.0.04 firmware.Been trying to open 9000 to access my buffalo media server remotely. Have set up both Single Port and Port Range Forwarding for port 9000.On trying to access media server, get message " could not connect to xxx.xxx.x.xxx:9000"Using online Open Ports Checkers shows this port is closed.
- Tried disabling all firewalls.
- tried range of ports
- Enabled/Disabled UPnP
- tried cisco & buffalo tech support
View 5 Replies
View Related
Dec 2, 2011
I have a philips tv 9000, qnap 210, twonky and e2000. When i using my e2000( wireless/cable) the tv stops playing the vids after 5 min.When i using un very old smc router there's no problem.
View 6 Replies
View Related
Mar 19, 2013
I've had some issues with my 892 router. [code] When match address is set to acl-net12, I can't ping my router on external interface and tunnel is working very bad (15%-20% packet loss).If I change match address from acl-net12 to acl-net12-new then I can ping my router on external interface and vpn si working fine.
I have also an acl (set on external interface) which allow ping but it seems that is not working when acl-net12 is used on crypto map. [code]
View 6 Replies
View Related
Mar 12, 2011
I have spent two days on the phone with virgin mobile broadband where I bought the device and they do not know what I am talking about.First of all the mifi is working fine on the one and only computer I have set up so for..it is Vista operating system..I am trying to set up my vista computer as an FTP server on the mifi or wifi or whatever you call it.when I disable the DHCP service on this virgin mobile mifi device so that I can generate my own internal ip for this particular computer..It is not functioning that is I cannot connect to the internet..I tried to get from Virginmobile the DNS server address but they were confused...When I log into the device itself under advanced options it does allow for me to disable DHCP..but my problem is what IP do I use when setting up the wireless connections, I disengaged the automatic, but I am having a heck of a time trying to use the right IP then the gateway address and the DNS.
View 14 Replies
View Related
Mar 14, 2013
Both my DIR-655 and DIR-815, when setup as wireless access points, are unable to ping external IP addresses and thus cannot contact the dlink ntp servers. I've disabled UPnP, disabled DHCP, changed the LAN IP address to an available address on the network. The wireless works, devices are getting an IP from the network DHCP server and can surf the internet. But the DLink router itself cannot ping any external IP addresses. But the DLink router itself cannot ping any external IP addresses.
View 3 Replies
View Related
Apr 30, 2012
I got my ea4500 all set up. never had a media servor or anything like that, figured this would be an easier way. when i hook up my exteral i can find it but i can only view the files in windows media player. how can i just browse the folders manually? WMP doesnt let me browse the folders as they actually are on the HDD which is such a pain in the **bleep**.
shows a device in "network infrastructure" but it says problem sending command to the program when i click that. i dont want to have to view the HDD in WMP as a media device...
View 1 Replies
View Related
May 10, 2012
i got an ea2700 and i cant get the external to work internally which i need for server tests now this has worked before on every other router i had without any editing done but this one doest allow that so what can i do to make it work with this router?
View 9 Replies
View Related
Jan 22, 2013
I have a EA3500 wireless router with the new style (smartwifi) firmware. I've scoured the web admin interface and can't find any sort of 'status' page that would tell me the external IP. I've looked through the support docs but they only show how to find internal/local IP.
View 2 Replies
View Related
Mar 16, 2008
How do I change my wireless router's (WRT54G) external IP address? I'm having IP conflicts with Yahoo and whenever I check the router's IP, it's always the same, despite the fact that my cable Internet provider uses DHCP to hand out IPs.
View 4 Replies
View Related
Jul 11, 2011
I cant remember where I read it but when I noticed that my HDD was running hot even when it was meant to be idle, I read that the router causes the storage device to run at full spin regardless.
I was wondering, do we know if that issue is fixed with this latest firmware update (June 14th)? I've had it on for about 10minutes but I'm not sure how long it takes to get to the temp that it was running at before.
View 4 Replies
View Related
Jul 30, 2011
Is it possible to add an external antenna to this WRT160Nv3 router? Some spots are just on the one bar signal level that comes and goes.
View 1 Replies
View Related
Nov 14, 2012
Since my PC died I have a few internal HDDs I would like to use in enclosures, what brands will work, or will most work if setup correctly ? Anything similar to work on a E4200 v1?
View 1 Replies
View Related
Jul 11, 2011
I'm trying to setup my home network so that I can access it when away from home but I've ran into problems and I can't figure out what is causing the problem.I've setup the router to forward incoming requests on port 80 to be directed to my PC running WAMP. The PC has a static IP and if I access it from another PC on my network I get the WAMP page load as expected.I've also setup an account with no-ip.com to resolve my (dynamic) ip. If I use the address they have setup while I'm on my network I get the login page for the router, again this is what I expect.The problem begins when I try and access my home address (whatever.no-ip.biz) from outside my network. I've tried it from 2 different locations and via a dial-up account and I get nothing.
View 6 Replies
View Related
Jun 9, 2011
DNS resolution works and I can surf the web without fail. But if I try to ping any external hosts (I can ping inside interface of ASA fine) from the LAN I get timeouts. I can ping anything from the ASA without fail.
ASA Version 8.4(1)
!
hostname fw1-nat-ann
domain-name inmd.infoblox.com
enable password anWLNen9CTFp7B/X encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
View 1 Replies
View Related
Mar 24, 2013
I have setup a new RV180 and it appears to be connected to the WAN, however, I cannot ping the external IP. In some of the documentation, there are references to default access rules, however, there does not appear to be any rules setup. What other settings need to be made to allow the firewall to be pinged on the WAN interface?
View 1 Replies
View Related
Nov 24, 2012
I formatted my new 3TB External hard drive on my computer and it shows close to 3TB space. Now when I hook it up to EA6500 router, it shows on 746.51 GB total. I have latest firmware installed.
View 8 Replies
View Related
May 20, 2012
I now have a shared drive shortcut on my desktop from the external drive I have hooked to the EA4500. Is there a way to share this folder to Android phones or Ipads? Looking to backup my phone data to the share (photos)
View 2 Replies
View Related
Jan 2, 2012
Switched from a Netgear router to a Cisco E2500 and now my Samsung blue ray won't connect to internet.
It says physical connection established but can't connect to external network.
View 2 Replies
View Related
Aug 8, 2011
I have an E4200 wireless router and have bought myself an external hd for media sharing (STOR.E STEEL S 1TB disk (PA4252E-1HJ0). Unfortunately this disk comes with a Virtual CD partition on it, which can not be deleted or removed (url....)!! Despite this being massively annoying by itself it also renders my disk useless, as my router does not recognise the disk (to to the additional partition). Is there any possibility to extend the firmware or to provide a fix that allows me to use the partitions on the disk, despite this additional "virtual" device?
View 6 Replies
View Related
Jan 14, 2011
I have an e300 router with my external hdd connected via the USB port. I am trying to figure out how to access the hdd remotely. I am not trying to get to it through remote desktop access. I have my laptop that I take with me when away from home but I would like to be able to access the hdd via Internet.
View 4 Replies
View Related
May 8, 2011
E3000 can see only 1TB Maximum. I have a 3TB WD storage and E3000. I have upgraded also to latest E3000 firmware version.
View 3 Replies
View Related
Aug 7, 2011
I looked around on the forum here for info, but couldn't find anything. I am attempting to hook up a Drobo to my WRT610N and it doesn't show up under the router setup page. I have updated to the latest firmware.
View 4 Replies
View Related
May 23, 2012
I have a Linksys WRT350N which I am trying to use an app on my iPhone to connect to my server using the public/external IP of my cable modem. I have the necessary ports opened and also tried adding the server to the DMZ but no matter what I can not get the app to connect to my server via my external IP when I am on my WiFi. I can connect without any problems if I use the NATed IP on the server when my phone is connected to the WiFi. It also works fine connecting to the external IP if I am on any other WiFi or the cellular network (which shows ports are forwarded correctly). I just can't connect to the server when I use the external IP and I am on my WiFi network. This is annoying as I need to keep changing the app's settings back and forth between the external and internal IP whenever I am home or away. I am left thinking this is some kind of issue with the WRT350N not allowing local internal traffic to reach the external IP. Any way to resolve this, maybe by entering a static route?
View 2 Replies
View Related
Dec 29, 2012
using a Linksys E2500. I have a Ubuntu "server" set up which i can access on my LAN through VNC Viewer (windows machines) no problem. I can even access it through the external IP address on a machine inside the LAN (both internal address and external address work from inside the LAN). I set up port forwarding (per portforward.com) but i still can not access my machine from outside the LAN. It has a static IP as well btw.
View 2 Replies
View Related
Mar 22, 2012
I'm looking to purchase the E4200 and use an external HDD with enclose as a NAS (probably just a backup drive), specifically this model. [code]The HDD would be a 1TB Samsung Spinpoint F3.Does this router allow for USB 3 connections or at least fallback to USB 2? The first comment on the external enclose says so otherwise.
View 3 Replies
View Related
Nov 4, 2011
I've configured a 5505 but internal clients can't ping external ip. To test I've connect a pc with the ip of the default router on the Outside int the ASA can ping the PC and the PC can ping the ASA, but internal clients can't ping the PC
PC config 195.12.23.241/28
Here's the ASA config, so far I've wiped the ASA and started with a blank sonfig and built it up but still not working.
ASA Version 8.2(5)
!
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
[Code] .....
View 2 Replies
View Related
Jan 14, 2013
As a raw test it is handy for us to ping externally the WAN port of the SRP 527W. How we configure the SRP 527W to allow this? FYI we have the inbulit SRP firewall enabled.
View 2 Replies
View Related
Mar 1, 2010
I have a 1760-v router set up at my home lab and I am unable to access IP addresses outside my local network. I have my Cisco router's fast Ethernet port connected to a small net gear router which then connects to my cable modem. The Cisco router is able to ping local address fine, but when I try to ping an outside address or domain name it times out. However, when I am at the CLI and type something like Ping { URL}, it resolves Google's IP address but it will not ping it. I have IP DEFAULT-GATEWAY and IP NAME-SERVER both pointing to my net gear router and pointing to my ISP's DNS server.
View 3 Replies
View Related
Jun 12, 2012
Similar to this issue with the EA4500 - I have the same issue with maping the drives from both PC and Mac - the USB drive is recognized, admin/user names are coreated appropriately, the folder structure is imported into the admin control..similar issue with EA4500 user here
View 3 Replies
View Related
Jul 30, 2012
I have a E3000 and just upgraded my Mac with the OS X Mountain Lion. I can't access my external HD anymore, although when I go to the router set up, on the storage tab, the router appears to recognize the HD.
View 9 Replies
View Related
