D-Link DIR-655 :: Unable To Ping External IPs When Used As Wireless AP
Mar 14, 2013
Both my DIR-655 and DIR-815, when setup as wireless access points, are unable to ping external IP addresses and thus cannot contact the dlink ntp servers. I've disabled UPnP, disabled DHCP, changed the LAN IP address to an available address on the network. The wireless works, devices are getting an IP from the network DHCP server and can surf the internet. But the DLink router itself cannot ping any external IP addresses. But the DLink router itself cannot ping any external IP addresses.
View 3 Replies
ADVERTISEMENT
Jul 11, 2011
I'm trying to setup my home network so that I can access it when away from home but I've ran into problems and I can't figure out what is causing the problem.I've setup the router to forward incoming requests on port 80 to be directed to my PC running WAMP. The PC has a static IP and if I access it from another PC on my network I get the WAMP page load as expected.I've also setup an account with no-ip.com to resolve my (dynamic) ip. If I use the address they have setup while I'm on my network I get the login page for the router, again this is what I expect.The problem begins when I try and access my home address (whatever.no-ip.biz) from outside my network. I've tried it from 2 different locations and via a dial-up account and I get nothing.
View 6 Replies
View Related
Mar 1, 2010
I have a 1760-v router set up at my home lab and I am unable to access IP addresses outside my local network. I have my Cisco router's fast Ethernet port connected to a small net gear router which then connects to my cable modem. The Cisco router is able to ping local address fine, but when I try to ping an outside address or domain name it times out. However, when I am at the CLI and type something like Ping { URL}, it resolves Google's IP address but it will not ping it. I have IP DEFAULT-GATEWAY and IP NAME-SERVER both pointing to my net gear router and pointing to my ISP's DNS server.
View 3 Replies
View Related
Aug 7, 2011
Just updated to the 1.01 firmware on my DIR-815 and now it doesn't handle loopbacks anymore.
For instance, I have a dyndns address of ericnewton76.dyndns.org. This points to my router. Works fine if you're NOT within the router's internal network, ie, outside hosts can get in just fine (try it... http:// , you'll see an IIS7 welcome screen)
However, when INSIDE the network, the requests don't get connected properly, and they used to... ie, I work with code, so my svn repo is at ericnewton76.dyndns.org/svn but inside my network it doesn't connect properly anymore (whereas it used to before firmware update)
So now I wish I could back-peddle to 1.0 firmware.
View 6 Replies
View Related
Jul 29, 2011
I'm trying to do port forwarding on my DIR-615...first of all I need to be able to ping the router from outside! I did enable the ping options to allow request from WAN...still don't work!!I removed the router and plug my laptop directly on my cable modem adapter and I'm able to ping my IP address (did put the same address the router had)...so, the IP is OK and it is possible to get in the modem from outside.I did plug back the router, and still not working...I did some trick like enable all IP with the Inbound filter...give access to few MAC address that I have to give more chances to get in and still not working!!!
View 6 Replies
View Related
Mar 12, 2011
I have spent two days on the phone with virgin mobile broadband where I bought the device and they do not know what I am talking about.First of all the mifi is working fine on the one and only computer I have set up so for..it is Vista operating system..I am trying to set up my vista computer as an FTP server on the mifi or wifi or whatever you call it.when I disable the DHCP service on this virgin mobile mifi device so that I can generate my own internal ip for this particular computer..It is not functioning that is I cannot connect to the internet..I tried to get from Virginmobile the DNS server address but they were confused...When I log into the device itself under advanced options it does allow for me to disable DHCP..but my problem is what IP do I use when setting up the wireless connections, I disengaged the automatic, but I am having a heck of a time trying to use the right IP then the gateway address and the DNS.
View 14 Replies
View Related
Aug 15, 2011
I'm looking to setup a few ip security cameras in my house and would like to monitor from work. The first thing I did was give the ip camera a static ip on my local LAN 192.168.1.104. I also forwarded port 9000 to this ip. I then went to [URL] to look up my external ip address. I was able to obtain one ip for my router and another for my modem (disconnected router and went direct through modem).
I've since tried to ping my router WAN ip from work numerous times via http://24.x.xxx.xx:9000 and I get timeout errors. I've tried traceroute and it gets close, but times out the last 3 hops. I've had Comcast on the phone many times trying to resolve and needless to say they weren't able to work.
View 6 Replies
View Related
Jan 18, 2013
From My Router that connects to Cable modem i am unable to ping website 4.2.2.2I am able to ping all other websites fines.Same website i can ping from my pc and all other switches fine.Router has only 1 ACL thats for NAT.
View 25 Replies
View Related
Jun 9, 2011
DNS resolution works and I can surf the web without fail. But if I try to ping any external hosts (I can ping inside interface of ASA fine) from the LAN I get timeouts. I can ping anything from the ASA without fail.
ASA Version 8.4(1)
!
hostname fw1-nat-ann
domain-name inmd.infoblox.com
enable password anWLNen9CTFp7B/X encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
View 1 Replies
View Related
Mar 19, 2013
I've had some issues with my 892 router. [code] When match address is set to acl-net12, I can't ping my router on external interface and tunnel is working very bad (15%-20% packet loss).If I change match address from acl-net12 to acl-net12-new then I can ping my router on external interface and vpn si working fine.
I have also an acl (set on external interface) which allow ping but it seems that is not working when acl-net12 is used on crypto map. [code]
View 6 Replies
View Related
Mar 24, 2013
I have setup a new RV180 and it appears to be connected to the WAN, however, I cannot ping the external IP. In some of the documentation, there are references to default access rules, however, there does not appear to be any rules setup. What other settings need to be made to allow the firewall to be pinged on the WAN interface?
View 1 Replies
View Related
Nov 4, 2011
I've configured a 5505 but internal clients can't ping external ip. To test I've connect a pc with the ip of the default router on the Outside int the ASA can ping the PC and the PC can ping the ASA, but internal clients can't ping the PC
PC config 195.12.23.241/28
Here's the ASA config, so far I've wiped the ASA and started with a blank sonfig and built it up but still not working.
ASA Version 8.2(5)
!
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
[Code] .....
View 2 Replies
View Related
Jan 14, 2013
As a raw test it is handy for us to ping externally the WAN port of the SRP 527W. How we configure the SRP 527W to allow this? FYI we have the inbulit SRP firewall enabled.
View 2 Replies
View Related
Apr 20, 2012
I recently bought EA3500 router. I am not able to hook up 2 storage external HDD and 1 USB printer usnig the router.I am connecting all 3 to a USB hub which i am connecting to the router.
View 1 Replies
View Related
Feb 1, 2011
I am trying to setup an RV016 router to do "1 to 1 NAT". I am starting with setting the external IP address of my RV016 to 10.8.58.219 on the WAN1 port, and LAN IP 10.10.20.254. Simple enough. When I connect my laptop to port1 on the router's LAN side I can ping the router's external AND internal IP addresses fine; But I can not ping from outside when connected through WAN1 port.I am performing a simple local test with an external hub, I put a patch cable from WAN1 port to the hub, another patch cable from port 1 on LAN side to the same hub, and from my laptop to the hub. When I use my laptop's IP address with the internal schema (10.10.20.100 for example) I can ping both WAN1 and LAN IP's; but when I use on my laptop the external IP schema (10.8.58.100 for example) I can not ping it. Therefore is not working when I connect my router to the real network.I went into the web setup pages of the router and dissabled: firewall and basicaly all security "blocks" it has, and leave it open for my testing.
View 1 Replies
View Related
Mar 2, 2013
I have installed a couple of SRP547W's and can't ping the external side of the ADSL interface.
Is there an option to turn on "respond to ping" and also are you able to forward to a internal IP?
View 3 Replies
View Related
Dec 10, 2010
I have some issues with router configuration. I cannot open any external web pages, but ping or telnet is just fine. Im using router-on-a-stick scenario. Router connected to LAN trough EtherSwitch module. Config attached.
View 8 Replies
View Related
Apr 14, 2011
We have a Cisco 871W working as PIX, controlling external VPN connections to our private network.The configuration is very similar to the one described here - "Cisco Router as a Remote VPN Server using SDM Configuration Example" url...
About once a week, it stops working, without aparent external intervention.The ping to the external IP stops answering, and the internal IP stops answering pings also.The solution is power-off and power-on, and it starts working again ...
What is the correct way to debug this situation ?I can connect a HyperTerminal using direct cable to the 871, but dont know the relevant commands to debug this situation.
Is there any LOG I can have a look into ? Yes, I am quite new to Cisco world .By the way : "show version" says Cisco IOS Software, C870 Software (C870-ADVSECURITYK9-M), Version 12.4(15)T7, RELEASE SOFTWARE (fc3)
View 20 Replies
View Related
Jun 14, 2011
I have installed quite recently a cisco ASA 5520 replacing a linux based firewall I have only 2 zones ..one is internal netowrk and other external the internal network has web servers, dns and mail server all having public IPs Every thing is OK but i have seen that if I try to ping an external server for example [URL] i cannot ping says
[sylvan@kmdns1 ~]$ ping www.yahoo.com
PING eu-fp.wa1.b.yahoo.com (87.248.112.181) 56(84) bytes of data.
--- eu-fp.wa1.b.yahoo.com ping statistics ---
6 packets transmitted, 0 received, 100% packet loss, time 5010ms
but I can ping from systems which are outside my firewall perfectly with the linux firewall i had before i could ping perfectly to yahoo from any of my internal servers?
View 5 Replies
View Related
Jun 17, 2012
I have installed 2 Cisco 1310's, connecting two buildings that are about 1000 yards apart. One access point is connected to an existing 3560 24 port switch, the other access point has a new 3560 24 port switch connected to it. Also installed 4 1240 access point in the newly connected building to the new switch. Issue is my router and existing switches can not ping any devices on the other side of the bridge. They can ping both access points that make the bridge. I consoled the new switch and could ping the existing switches and router, after doing that the other switches and router are now able to ping the new switch. Now my main issue is I have a user using a 7921 phone connected to one of the new 1242's, when he makes a call to a person in the first building they can hear him, however he can not hear them. Our call manager is in another state were I am located. I can call him and vise versa, and we can hear each other. I have went over my configs server times, and doubled check my IOS versions to make sure they are up to date. I will be glad to provide configs upon request.
View 1 Replies
View Related
Jun 1, 2011
I have Aironet 1240AG and the 2 laptops connected to same SSID. Unable to can ping each other but can ping/browse server on wired.
Below are my config:
Current configuration : 2646 bytes!version 12.4no service padservice timestamps debug datetime msecservice timestamps log datetime msecservice password-encryption!hostname AP2!enable secret 5 $1$7EVQ$2FN7ewjcrwKCICIfmFgCO.!no
[Code].....
View 2 Replies
View Related
Feb 13, 2012
I am missing something and i dont no what but i am trying to ping a pc on the same network but get a destination host is unreachable. Can any one think of anything that could be causing this, i can ping the default gateway and internet address's?
!
interface FastEthernet0
no cdp enable
[Code].....
View 11 Replies
View Related
Mar 30, 2013
Model : TL-WR2543ND
Hardware Version : V1
Firmware Version :
ISP : I have an external HDD that I regularly use in any computer I have access.It's an HDD enclosure 2.5" 3.0 USB, with a 750GB WD HDD inside. I use it in computers with all versions of USB, even in my TV. It doens't require an external power source, and just have 01 input/output, which is a USB port.After plugging it in the router (running with the last available firmware from TP-LINK - 3.13.27 Build 121207), I entered the setup screen of the router, and under USB Settings, pressed RESCAN, but the HDD wasn't recognized.What happens is that when I plug it in the router, the LED in it starts blinking (in normal usage, the LED becomes red for a couple of seconds, and then becomes steadly blue, when it gets connected into a equipment). It is probably a matter of power, as if the router wasn't providing enough power to it when it's plugged.Afterwards, I've made the following tests:
1) Used this External HDD in 3 different equipments (a notebook, a netbook and a TV), with different versions of USB ports. It was recognized and read normally in all of them.
2) I tested a pendrive with the router. After RESCAN, it was shown normally in Storage Sharing page.
3) I have downgraded the firmware to 120509 version, plugged the HDD in the router, and once again, it was an unsuccessful try.
What I can conclude from those tests is that:
1) My External HDD is working normally;
2) The router's USB port is working properly;
3) So, if both are working, it can only be a matter of compatibility between them.
View 2 Replies
View Related
Nov 20, 2011
I've got a new E4200 router, Everything works just fine, but I'm unable to ping any WiFi hosts from my LAN, I can ping LAN from any WiFi Host.If I disable NAT on the E4200 I'm able to ping WiFi hosts but then all WiFi Hosts are unable to talk to the LAN.
LAN - 192.9.209.0
WiFi - 172.16.1.0
Same config runs perfect on my WRTG54GL.
View 1 Replies
View Related
Jan 27, 2012
I've got a new E4200 router, Everything works just fine, but I'm unable to ping any WiFi hosts from my LAN, I can ping LAN from any WiFi Host.If I disable NAT on the E4200 I'm able to ping WiFi hosts but then all WiFi Hosts are unable to talk to the LAN.
LAN - 192.9.209.0
WiFi - 172.16.1.0
Same config runs perfect on my WRTG54GL.
View 1 Replies
View Related
Nov 15, 2012
We have a WLC 4410 management IP Address configured as 10.40.124.59.and configured VLAN1 on WLC with IP address 10.40.126.250. we are unable to ping the VLAN1 ip address from the switch. even unable to ping 10.40.126.252 (Gateway). Is there any limitation that we can not configured ip address from secondary scope...Switch vlan 1 configuration is ......interface GigabitEthernet0/0.1description Business VLANencapsulation dot1Q 1 nativeip address 100.93.50.2 255.255.0.0 secondaryip address 10.40.126.252 255.255.255.0 secondaryip address 10.40.124.61 255.255.255.192 secondaryip address100.43.94.252 255.255.255.0.
View 3 Replies
View Related
Jul 28, 2012
I have an 871 set up at home with 2 VLANs, both of these vlans present a strange behavior where an user is unable to ping/contact another user on the same subnet, however if users are on different subnet it seems to work [code]
According to the troubleshooting that I have done, the issue seems to be with the broadcast traffic, ARP request/reply do not reach another host on the same subnet (wireless to wireless or wired to wireless) however if the wireless device iniciates the connection to wired, it works fine.
I have tried to enable proxy arp on the different VLANs and BVI and different combinations but no sucess in order to get traffic across 2 wireless devices on the same subnet or a connection that is iniciated for a wired client to a wireless one.
I tried enabling and disabling dot11 arp-cache but no luck.
View 2 Replies
View Related
Mar 7, 2012
We are in the process of evaluating Cisco wireless controllers and AP. We have 3602 APs and 2504 controllers right now. We have multiple branch offices connected to the main office through layer 3 and they all have different vtp domains and vlans. I am trying to deploy APs at the branch offices and connect them back to the controller and the central site. I created a sub interface and ssid with one of the vlans at the branch office on the controller and was able to get the AP to join the controller through DNS. However, a client at the branch office connected to the AP was unable to ping anything at the branch and central sites. Any documentations on how to deploy such a setup where the controller is at the central site and AP at the branch office going through multiple routers in between?
View 1 Replies
View Related
Oct 31, 2012
Region : Ireland
Model : TD-W8961ND
Hardware Version : V1
Firmware Version : 1.0.0 Build 111125 Rel.28195
ISP : Eircom
I'm trying to set up external Wake On Lan with my TP Link router.
I can get it working internally using the mac address I'm just wondering how do I do it remotely?
View 7 Replies
View Related
Dec 6, 2012
Region : UnitedStates
Model : TL-WR1043ND
Hardware Version : Not Clear
Firmware Version : 3.6
ISP : comcast
what do i need to do to have my laptop access an Iomega EZ networked external hard drive? It is not my firewall on computer so Norton said it is the router.
View 1 Replies
View Related
May 7, 2012
I am using Linksys E4200 wireless router. I connected two machines, this way.
|LAP1|--------(LAN ethernet connection)----------|LinksysE4200|-------(Internet wired connection)--------|LAP2|
On the Linksys E4200, the Internet wired connection side, I gave static IP address which is in the same network range as that of LAP2.When tried to ping from LAP1 to LAP2, ping doesnot happen. Any settings by which I can ping from LAP1 to LAP2.
View 2 Replies
View Related
Feb 25, 2013
Region : UnitedKingdom
Model : TL-WDR3600
Hardware Version : V1
I am trying to restrict external access to a ftp server I have running, to a single external IP address. Is this possible? It can be done for the Remote Management IP Address page, where you can enter a single address or 255.255.255.255 to allow all external hosts. But the set up of a virtual server does not appear to have that option.
View 1 Replies
View Related
Feb 15, 2013
Region : UnitedKingdom
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 3.13.26
ISP : Virginmedia
I've plugged a 3tb seagate backup plus external hard drive into the routers USB port and its not being recognised my other wd 1tb has no problem being picked up.
View 6 Replies
View Related
