Region : UnitedKingdom
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 3.13.26
ISP : Virginmedia
I've plugged a 3tb seagate backup plus external hard drive into the routers USB port and its not being recognised my other wd 1tb has no problem being picked up.
Region : UnitedStates
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 3.13.26 Build 130129 Rel.59449n
ISP :
I try to attach an external hard drive to my TL-WDR3600.
The hard drive: TOSHIBA Canvio Desk 3TB USB 3.0 Black Desktop External Hard Drive HDWC130XK3J1 Formatted w/ NTFS, 4kB Block Size (default)
When I attach the drive and click Rescan in "USB Settings" -> "Storage Sharing" nothing happens.Message is still: No volumes found. Plug an external USB drive into this Router, wait for 10 seconds and then rescan the volume.
No entries are made in the "System Tools" -> "System Log" when I attach the drive or click rescan.
The drive works fine on my desktop PC running Windows 8.
I realize that it is a USB 3.0 drive, but I understand that USB 3.0 should be backwards compatible to USB 2.0. In fact, the drive works on both, USB 3.0 and USB 2.0 ports, on my desktop PC.
What are the requirements and/or restrictions for USB hard drives on the TL-WDR3600? The information I found was, that they need to be either formatted with NTFS or FAT32 (FAT32 is not an option here due to the disk size). Are there any size restrictions for external drives on the router? Why are they not listed anywhere (user manual, specifications).
Region : UnitedKingdom
Model : TL-WDR3600
Hardware Version : V1
I am trying to restrict external access to a ftp server I have running, to a single external IP address. Is this possible? It can be done for the Remote Management IP Address page, where you can enter a single address or 255.255.255.255 to allow all external hosts. But the set up of a virtual server does not appear to have that option.
Region : Netherlands
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 130129
ISP :
I've this dualband wireless router since a week.Now I found out, NFS is working very slow (actually NFS is not working at all).I have a Mede8er and a synology NAS server connected to the TP-LINK WDR3600 router.I have movie directories shared on the NAS using NFS.when I go to the NFS locations in my mede8er it takes very long before I can see the NFS mapping.When I connect the Mede8er straight to the Synology NAS server (Cross Cable connection) NFS is working as it should be.So the TP-LINK WDR3600 cannot handle the NFS protocol?
Region : Brazil
Model : TL-WDR3600
Hardware Version : V1
Firmware Version :
ISP :
I want to change the antennas on my wdr3600 to increase the range of the signal because my walls are too thick. I can not find TP link brand Dual Band Antennas, so I search ebay and found this:
[url]....
Any dual band RP-SMA antenna is compatible with the WDR3600? or do I need to search for something in particular?
Region : UnitedStates
Model : TL-WDR3600
Hardware Version : V1
Firmware Version :
ISP :
I recently bought wdr3600 and just trying to configure bridge through WDS configuration. I just enabled WDS and picked my initial wireless router after clicking the Survey button, then save it. After the reboot, I cant seem to ping/access 192.168.0.1 and the wireless SSID cant be seen any longer. I tried doing the reset button for 30secs but looks like nothing is working and not resetting. And I am still getting 169.254.x.x
Region : Italy
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 3.13.17 Build 120508 Rel.45884n
ISP :
I've got two WDR3600
the first one is the main router:
- connected to ISP modem
- DHCP on
- 2.4Ghz radio to serve WiFi clients security WPA-PSK
- 5GHz radio to link to the second WDR3600
protocol 802.11n only
the second WDR3600 is WDS of the main router:
- DHCP off
- 2.4GHz radio to serve WiFi clients security WPA-PSK
- 5GHz radio to link to the first WDR3600
protocol 802.11n only
All is working fine, however WDS connection works only with security off. WPA-PSK is not selectable, cannot test WPA2, no radius server available, WEP not supported due to incompatibilty with 802.11n protocol. Is this the expected behaviour? How to get WDS working with WPA-PSK encryption? Could this be due to the firmware or s it a limitation of Atheros chipset?
Region : Netherlands
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 120820 Rel.73549n
ISP :
I recently purchased an TL-WDR3600. Setup was easy. Both wlan channels work perfectly. All clients can connect to the internet and access my lan connected NAS. I have some wlan devices which needs to be connected sometimes by http: port 80 and also by telnet or ssh. I can connect from a wlan device to a lan device. But NOT from a wlan to wlan or a lan to wlan. I allready diabled WMM and tried some other wlan settings, like disable one channel, changing the channel width etc.
My setup is : ADSL device -->(192.168.1.X dhcp) WAN TL-WDR3600 --> to LAN&WLAN (192.168.0.X dhcp and some LAN connected with static 0.200, 0.210)
Region : Ireland
Model : TL-WDR3600
Hardware Version : Not Clear
Firmware Version :
ISP : UPC
how do you add a password for anyone trying to access the hard drive that I have connected to the 3600 via usb. I have guests staying in the house on a regular basis and only want to allow family member to be able to access the hard drive that I have connected to the router.
Region : Spain
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 3.13.23 Build 120820 Rel.73549n
ISP : Portal Wimax
I have enabled USB Print Server on the router and managed to print from my main PC (connected by cable to router).
However, I cannot get it to work on my laptop.
I connected my laptop running Windows 7 x64 by cable to router, ran the USB print server software (latest version downloaded from web site). The USB server software sees my printer (Canon Pixma iP4200). It appears in the list to auto-connect but there is an X against it and if I try and set it to auto connect, I get the error "the port of auto-connect can not be a LPR/Raw TCP/SMB port". Apart from the occurrence of the printer I had installed before (so, yes the printer driver is installed), the USB-server printer does not appear in my system printer list.
Region : UnitedStates
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : TL-WDR3600_V1_120820
ISP : Cox cable
It doesn't matter how I set it up, once the policy is enabled nothing can get through. This is the same for "deny" or "allow" as default. Is there bug with this new firmware TL-WDR3600_V1_120820??
Region : Russia
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 3.13.23 Build 120820 Rel.73549n
ISP : VIMPELCOM
I have portable hard disk connected to one of the TL-WDR3600 router usb ports (another one has printer connected to it)
Write speed is about 3Mbytes/sec maximum.Real disk write speed is about 35-38Mbytes/sec - if I connect it to one of the PC USB ports (both router and PC ports are USB 2.0)Why write speed via router is so low?
My PC is connected to router via cable and is running Windows 7 32bit Ultimate SP1, hard disk partition is 465Gb NTFS single volume.I'm measuring speed simply by coping 1.4Gb file through Windows Explorer to \tplinklogin.net (following USB storage access instructions from router control panel) in first case and directly to hard disk - in second case.
Region : UnitedKingdom
Model : TL-WDR4300
Hardware Version : not clear
Firmware Version :
ISP : BT
I am thinking of buying a TL-WDR3600, but just need to know the answer to the question below.Can anyone confirm if the TL-WDR3600 supports NAT Loopback functionality?
Region : Poland
Model : TL-WDR3600
Hardware Version : V1
Firmware Version :
ISP :
I have some linksys router that I used as wireless client bridge. I have main router that is connected to Internet and linksys router which is connected to main router's WiFi. Linksys router acts as client bridge connecting LAN devices to main router. Now I own TL-WDR3600 and I would like to replace linksys router. How can I achieve the same on TP-Link router? I don't see any option for setting wireless operation mode.
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP :
I can view numerous other PDF files from other websites, and even PDF files from TP-LINK, but, the User Guide for the TL-WDR3600 or the 3500 error out when opening in a web browser. If I right click and download them, they will download but then error out on opening.
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 3.13.23 Build 120820 Rel.73549n
ISP : VIMPELCOM
To access USB Storage in Windows I simply type "\tplinklogin.net" in Run window.But how can I access it using Adnroid phone or tablet connected by Wi-Fi?Typing "\tplinklogin.net" in Browser adress line brings me to Google search, typing simply "tplinklogin.net" opens router web interface..
Region : Spain
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 3.13.26 Build 130129 Rel.59449n
ISP :
I've recently bought the TP-LINK WDR3600 and am very happy with it. I'm using its media server feature so I can watch movies on my TV through DLNA, but have found a problem: the MP4 files are not shown. All the other files work perfectly (AVI, MKV), but the MP4 files are not shown in Windows Media Player or LG Smart TV. I assume the Media Server software simply does not include this kind of files when scanning. Is there any way of accessing the media server configuration file and "enable" MP4 files?
Region : UnitedStates
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : TL-WDR3600_V1_130320
ISP :
Has anyone gotten the Guest Network feature to work from the new firmware TL-WDR3600_V1_130320?I have my WDR3600 setup as an access point:TPLINK with static IP address connected via ethernet cord from the LAN port and connected to the main Verizon FIOS router which distributes DHCP IP addresses to the netwrok. Can not get the Guest Network feature to work - I see the guest SSID I created but when I connect to it, the IP address assigned is in the 169. range meaning it does not get to my main router.It may be because I have the TPLINK setup as an access point, so are there any people who have gotten Guest Network work either with the TPLINK as the main router or as an access point?
Region : UnitedKingdom
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 3.13.26 Build 130129 Rel.59449n
ISP : Virgin Media Limited
when I forward ports I get the following error message:
Things to note:I have the web GUI running on 8080, because I run a file-server on port 80.
I am using a Virgin media branded router in 'modem mode', this would not cause issues.
I did not do anything to change anything, I went to add an additional port to forward and it didn't work.
I am on a Dynamic IP
After it stopped forwarding, I upgraded firmware to: 3.13.26 Build 130129 Rel.59449n.
Region : UnitedStates
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 3.13.26 Build 130129 Rel.59449n
ISP : Charter
I've set up my printer (HP PSC 2410) to the router using TL-WDR3600_V1.0_USB Print Service Client Setup and that part's fine. The USB Printer Controller sees the printer as an "auto-connected printer" and I can select the printer as my default to print to. My problem lies with the fact that every time I try to print something, it causes a BSOD. I'm using Windows 8 and checked to make sure the USB Print Service Client Setup program was compatible with Windows 8 before I attempted anything. The HP PSC 2410 printer is on the Print Server Compatibility list so I don't know why I'm having problems.
The error I get each time I try to print is: SYSTEM_SERVICE_EXCEPTION (TplinkUDSTcpBus.sys). One of the draws of this router was that I could hook up my printer via USB and print wirelessly
Region : UnitedStates
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 3.13.26 Build 130129 Rel.59449n
ISP :
I have the WDR-3600 with a usb drive. I have updated to latest firmware 3.13.26. I am having problems with the media server. I have 331 folders shared in the Music folder. When I access it via the DLNA it will only show the first 123 folders. I can access all of the folders via network share but not via the media server. I have checked this on my music player and my android phone and tablet. Both of them can only see the first 123 folders.
Region : CzechRepublic
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 3.13.26 Build 130129 Rel.59449n
ISP :
1. On my laptop in windows vista media player I cant see any shared media of media server TP-WDR3600: screen.jpg
2. My samsung tv shows all three shared folders of media server. When I try to play any Mp3 and avi files it says unsuported file format. In folder with jpg photos it shows nothing. I can see and play anything from my laptop media server on TV.
Region : United States
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP :
I just got the TL-WDR3600.
It seems to work fine and my Smart TV recognizes my network drive or usb hdd connected to the router.
However, the files on the network drive or usb hdd don't seem to appear/work. The folder the files are stored in are recognized, but not the files themselves.
I've plugged the usb HDD directly to the TV and it recognizes and plays the movie files fine, however when trying to find them via the wireless router, they don't appear/work.
Are there some settings i need to change to allow the TV to see/play the files?
Region : Hongkong
Model : TL-WDR3600
Hardware Version : V1
Firmware Version :
ISP :
When using the USB printer port share function, I found that some PCs, which had never physically connect to a USB printer before, will not have the virtual USB printer port in the port selection. In this way, TP-Link's USB printer controller will not be able to setup the connection. The PC will not be able to use the shared printer from my WDR3600.how can I create a virtual USB printer port in the remote PCs (without need to physically connect a printer to them) or other method to use the shared printer?
Region : Germany
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 3.13.26 Build 130129 Rel.59449n
ISP :
all my systems are configured under "IP & MAC Binding". Binding is activated globally and all check marks for every ID are set. After i finished my configurations, the "ARP List" status shows, that everything is bound - so far everything is great. The problem appears after a router reboot or after shutting the router down and powering it on again. The "ARP List" then shows only a few of my IDs and their status is unbound. I need to go back to the "Binding Settings" and hit "Save" - after that all my IDs appear in the ARP-List and everything is OK again.
Region : UnitedStates
Model : TL-WR1043ND
Hardware Version : Not Clear
Firmware Version : 3.6
ISP : comcast
what do i need to do to have my laptop access an Iomega EZ networked external hard drive? It is not my firewall on computer so Norton said it is the router.
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 3.13.23 Build 120820 Rel.73549n
ISP : Cable TV provider
It seems there is a bug with TL-WDR3600. As it can be seen in the following image, the UPnP is off:But my firewall on the computer is reporting flood of packets originating from the router (it's the routers MAC address and IP address):I don't know what ETH type packet is, 0026 might be hex (38 decimal as seen in the raw log). But port 1900 is definitely UPnP.At the router, the wireless switch is off, as well as all other options for sharing etc. This computer is the only one connected to the router. The router has been reset several times.
Region : UnitedStates
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 3.13.12 Build 120405 Rel.33996n
ISP : WR1043ND
The router is not showing my external hard drive in the usb settings. The Hard drive is a seagate 7200rpm 1.5tb. The hard drive works just fine when plugged into my computer. I have tried NTFS and EXFAT. My 2gb usb drive in FAT32 shows up just fine. The external has its own power supply. Is there anything I am missing that would cause it to not work?
Model : TL-WR2543ND
Hardware Version : V1
Firmware Version :
ISP : I have an external HDD that I regularly use in any computer I have access.It's an HDD enclosure 2.5" 3.0 USB, with a 750GB WD HDD inside. I use it in computers with all versions of USB, even in my TV. It doens't require an external power source, and just have 01 input/output, which is a USB port.After plugging it in the router (running with the last available firmware from TP-LINK - 3.13.27 Build 121207), I entered the setup screen of the router, and under USB Settings, pressed RESCAN, but the HDD wasn't recognized.What happens is that when I plug it in the router, the LED in it starts blinking (in normal usage, the LED becomes red for a couple of seconds, and then becomes steadly blue, when it gets connected into a equipment). It is probably a matter of power, as if the router wasn't providing enough power to it when it's plugged.Afterwards, I've made the following tests:
1) Used this External HDD in 3 different equipments (a notebook, a netbook and a TV), with different versions of USB ports. It was recognized and read normally in all of them.
2) I tested a pendrive with the router. After RESCAN, it was shown normally in Storage Sharing page.
3) I have downgraded the firmware to 120509 version, plugged the HDD in the router, and once again, it was an unsuccessful try.
What I can conclude from those tests is that:
1) My External HDD is working normally;
2) The router's USB port is working properly;
3) So, if both are working, it can only be a matter of compatibility between them.
I have a new techni colour wifi router TG582n which has a usb cobnnection in the side. I also have a new Samsung 400 gig external hard drive can these be linked to make a wifi hard disc store.
View 2 Replies View RelatedI'm currently in college, and do most things with my laptop, and I have wifi just about everywhere. It has a generous 500 GB of storage, but I'd like to store non-essential files on, an external hard drive. However, lugging around 3 TB of storage isn't exactly feasible, and with my experience with my current 1.5 TB portable drive, me running around everywhere with it bouncing in my bag is just going to abuse it until it stops functioning (which it has...)[URL]
View 3 Replies View RelatedI have a Windows 7 lap top and an Iomega eGo external hard drive. When I plug the hard drive into my computer via a USB, it works fine, but when i plug the hard drive in to the wireless router, I can not access it, and I would like access the hard drive wirelessly
View 2 Replies View RelatedI am looking to get access to an external hard drive that I have set up on my wireless network.When I try to do an automated Windows backup (off my Vista based laptop files) on to an external hard drive which is connected to my wireless network (through a Belkin router) I am being asked for a user name and password to access the connected hard drive on the network. The thing is that I don't remember setting up a username and password for the hard drive at all. I can paste single files mannually onto the external hard drive without being asked for a username and password. I did perform an automated Windows backup off my other Windows 7 laptop and was not ask for a username and password. where to find the username and password information ?
View 3 Replies View Related