Region : UnitedKingdom
Model : TL-WDR4300
Hardware Version : not clear
Firmware Version :
ISP : BT
I am thinking of buying a TL-WDR3600, but just need to know the answer to the question below.Can anyone confirm if the TL-WDR3600 supports NAT Loopback functionality?
Region : Netherlands
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 130129
ISP :
I've this dualband wireless router since a week.Now I found out, NFS is working very slow (actually NFS is not working at all).I have a Mede8er and a synology NAS server connected to the TP-LINK WDR3600 router.I have movie directories shared on the NAS using NFS.when I go to the NFS locations in my mede8er it takes very long before I can see the NFS mapping.When I connect the Mede8er straight to the Synology NAS server (Cross Cable connection) NFS is working as it should be.So the TP-LINK WDR3600 cannot handle the NFS protocol?
Region : Brazil
Model : TL-WDR3600
Hardware Version : V1
Firmware Version :
ISP :
I want to change the antennas on my wdr3600 to increase the range of the signal because my walls are too thick. I can not find TP link brand Dual Band Antennas, so I search ebay and found this:
[url]....
Any dual band RP-SMA antenna is compatible with the WDR3600? or do I need to search for something in particular?
Region : UnitedStates
Model : TL-WDR3600
Hardware Version : V1
Firmware Version :
ISP :
I recently bought wdr3600 and just trying to configure bridge through WDS configuration. I just enabled WDS and picked my initial wireless router after clicking the Survey button, then save it. After the reboot, I cant seem to ping/access 192.168.0.1 and the wireless SSID cant be seen any longer. I tried doing the reset button for 30secs but looks like nothing is working and not resetting. And I am still getting 169.254.x.x
Region : Italy
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 3.13.17 Build 120508 Rel.45884n
ISP :
I've got two WDR3600
the first one is the main router:
- connected to ISP modem
- DHCP on
- 2.4Ghz radio to serve WiFi clients security WPA-PSK
- 5GHz radio to link to the second WDR3600
protocol 802.11n only
the second WDR3600 is WDS of the main router:
- DHCP off
- 2.4GHz radio to serve WiFi clients security WPA-PSK
- 5GHz radio to link to the first WDR3600
protocol 802.11n only
All is working fine, however WDS connection works only with security off. WPA-PSK is not selectable, cannot test WPA2, no radius server available, WEP not supported due to incompatibilty with 802.11n protocol. Is this the expected behaviour? How to get WDS working with WPA-PSK encryption? Could this be due to the firmware or s it a limitation of Atheros chipset?
Region : Netherlands
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 120820 Rel.73549n
ISP :
I recently purchased an TL-WDR3600. Setup was easy. Both wlan channels work perfectly. All clients can connect to the internet and access my lan connected NAS. I have some wlan devices which needs to be connected sometimes by http: port 80 and also by telnet or ssh. I can connect from a wlan device to a lan device. But NOT from a wlan to wlan or a lan to wlan. I allready diabled WMM and tried some other wlan settings, like disable one channel, changing the channel width etc.
My setup is : ADSL device -->(192.168.1.X dhcp) WAN TL-WDR3600 --> to LAN&WLAN (192.168.0.X dhcp and some LAN connected with static 0.200, 0.210)
Region : Ireland
Model : TL-WDR3600
Hardware Version : Not Clear
Firmware Version :
ISP : UPC
how do you add a password for anyone trying to access the hard drive that I have connected to the 3600 via usb. I have guests staying in the house on a regular basis and only want to allow family member to be able to access the hard drive that I have connected to the router.
Region : Spain
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 3.13.23 Build 120820 Rel.73549n
ISP : Portal Wimax
I have enabled USB Print Server on the router and managed to print from my main PC (connected by cable to router).
However, I cannot get it to work on my laptop.
I connected my laptop running Windows 7 x64 by cable to router, ran the USB print server software (latest version downloaded from web site). The USB server software sees my printer (Canon Pixma iP4200). It appears in the list to auto-connect but there is an X against it and if I try and set it to auto connect, I get the error "the port of auto-connect can not be a LPR/Raw TCP/SMB port". Apart from the occurrence of the printer I had installed before (so, yes the printer driver is installed), the USB-server printer does not appear in my system printer list.
Region : UnitedStates
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : TL-WDR3600_V1_120820
ISP : Cox cable
It doesn't matter how I set it up, once the policy is enabled nothing can get through. This is the same for "deny" or "allow" as default. Is there bug with this new firmware TL-WDR3600_V1_120820??
Region : Russia
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 3.13.23 Build 120820 Rel.73549n
ISP : VIMPELCOM
I have portable hard disk connected to one of the TL-WDR3600 router usb ports (another one has printer connected to it)
Write speed is about 3Mbytes/sec maximum.Real disk write speed is about 35-38Mbytes/sec - if I connect it to one of the PC USB ports (both router and PC ports are USB 2.0)Why write speed via router is so low?
My PC is connected to router via cable and is running Windows 7 32bit Ultimate SP1, hard disk partition is 465Gb NTFS single volume.I'm measuring speed simply by coping 1.4Gb file through Windows Explorer to \tplinklogin.net (following USB storage access instructions from router control panel) in first case and directly to hard disk - in second case.
Region : Poland
Model : TL-WDR3600
Hardware Version : V1
Firmware Version :
ISP :
I have some linksys router that I used as wireless client bridge. I have main router that is connected to Internet and linksys router which is connected to main router's WiFi. Linksys router acts as client bridge connecting LAN devices to main router. Now I own TL-WDR3600 and I would like to replace linksys router. How can I achieve the same on TP-Link router? I don't see any option for setting wireless operation mode.
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP :
I can view numerous other PDF files from other websites, and even PDF files from TP-LINK, but, the User Guide for the TL-WDR3600 or the 3500 error out when opening in a web browser. If I right click and download them, they will download but then error out on opening.
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 3.13.23 Build 120820 Rel.73549n
ISP : VIMPELCOM
To access USB Storage in Windows I simply type "\tplinklogin.net" in Run window.But how can I access it using Adnroid phone or tablet connected by Wi-Fi?Typing "\tplinklogin.net" in Browser adress line brings me to Google search, typing simply "tplinklogin.net" opens router web interface..
Region : Spain
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 3.13.26 Build 130129 Rel.59449n
ISP :
I've recently bought the TP-LINK WDR3600 and am very happy with it. I'm using its media server feature so I can watch movies on my TV through DLNA, but have found a problem: the MP4 files are not shown. All the other files work perfectly (AVI, MKV), but the MP4 files are not shown in Windows Media Player or LG Smart TV. I assume the Media Server software simply does not include this kind of files when scanning. Is there any way of accessing the media server configuration file and "enable" MP4 files?
Region : UnitedStates
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 3.13.26 Build 130129 Rel.59449n
ISP :
I try to attach an external hard drive to my TL-WDR3600.
The hard drive: TOSHIBA Canvio Desk 3TB USB 3.0 Black Desktop External Hard Drive HDWC130XK3J1 Formatted w/ NTFS, 4kB Block Size (default)
When I attach the drive and click Rescan in "USB Settings" -> "Storage Sharing" nothing happens.Message is still: No volumes found. Plug an external USB drive into this Router, wait for 10 seconds and then rescan the volume.
No entries are made in the "System Tools" -> "System Log" when I attach the drive or click rescan.
The drive works fine on my desktop PC running Windows 8.
I realize that it is a USB 3.0 drive, but I understand that USB 3.0 should be backwards compatible to USB 2.0. In fact, the drive works on both, USB 3.0 and USB 2.0 ports, on my desktop PC.
What are the requirements and/or restrictions for USB hard drives on the TL-WDR3600? The information I found was, that they need to be either formatted with NTFS or FAT32 (FAT32 is not an option here due to the disk size). Are there any size restrictions for external drives on the router? Why are they not listed anywhere (user manual, specifications).
Region : UnitedStates
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : TL-WDR3600_V1_130320
ISP :
Has anyone gotten the Guest Network feature to work from the new firmware TL-WDR3600_V1_130320?I have my WDR3600 setup as an access point:TPLINK with static IP address connected via ethernet cord from the LAN port and connected to the main Verizon FIOS router which distributes DHCP IP addresses to the netwrok. Can not get the Guest Network feature to work - I see the guest SSID I created but when I connect to it, the IP address assigned is in the 169. range meaning it does not get to my main router.It may be because I have the TPLINK setup as an access point, so are there any people who have gotten Guest Network work either with the TPLINK as the main router or as an access point?
Region : UnitedKingdom
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 3.13.26 Build 130129 Rel.59449n
ISP : Virgin Media Limited
when I forward ports I get the following error message:
Things to note:I have the web GUI running on 8080, because I run a file-server on port 80.
I am using a Virgin media branded router in 'modem mode', this would not cause issues.
I did not do anything to change anything, I went to add an additional port to forward and it didn't work.
I am on a Dynamic IP
After it stopped forwarding, I upgraded firmware to: 3.13.26 Build 130129 Rel.59449n.
Region : UnitedStates
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 3.13.26 Build 130129 Rel.59449n
ISP : Charter
I've set up my printer (HP PSC 2410) to the router using TL-WDR3600_V1.0_USB Print Service Client Setup and that part's fine. The USB Printer Controller sees the printer as an "auto-connected printer" and I can select the printer as my default to print to. My problem lies with the fact that every time I try to print something, it causes a BSOD. I'm using Windows 8 and checked to make sure the USB Print Service Client Setup program was compatible with Windows 8 before I attempted anything. The HP PSC 2410 printer is on the Print Server Compatibility list so I don't know why I'm having problems.
The error I get each time I try to print is: SYSTEM_SERVICE_EXCEPTION (TplinkUDSTcpBus.sys). One of the draws of this router was that I could hook up my printer via USB and print wirelessly
Region : UnitedKingdom
Model : TL-WDR3600
Hardware Version : V1
I am trying to restrict external access to a ftp server I have running, to a single external IP address. Is this possible? It can be done for the Remote Management IP Address page, where you can enter a single address or 255.255.255.255 to allow all external hosts. But the set up of a virtual server does not appear to have that option.
Region : UnitedStates
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 3.13.26 Build 130129 Rel.59449n
ISP :
I have the WDR-3600 with a usb drive. I have updated to latest firmware 3.13.26. I am having problems with the media server. I have 331 folders shared in the Music folder. When I access it via the DLNA it will only show the first 123 folders. I can access all of the folders via network share but not via the media server. I have checked this on my music player and my android phone and tablet. Both of them can only see the first 123 folders.
Region : UnitedKingdom
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 3.13.26
ISP : Virginmedia
I've plugged a 3tb seagate backup plus external hard drive into the routers USB port and its not being recognised my other wd 1tb has no problem being picked up.
Region : CzechRepublic
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 3.13.26 Build 130129 Rel.59449n
ISP :
1. On my laptop in windows vista media player I cant see any shared media of media server TP-WDR3600: screen.jpg
2. My samsung tv shows all three shared folders of media server. When I try to play any Mp3 and avi files it says unsuported file format. In folder with jpg photos it shows nothing. I can see and play anything from my laptop media server on TV.
Region : United States
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP :
I just got the TL-WDR3600.
It seems to work fine and my Smart TV recognizes my network drive or usb hdd connected to the router.
However, the files on the network drive or usb hdd don't seem to appear/work. The folder the files are stored in are recognized, but not the files themselves.
I've plugged the usb HDD directly to the TV and it recognizes and plays the movie files fine, however when trying to find them via the wireless router, they don't appear/work.
Are there some settings i need to change to allow the TV to see/play the files?
Region : Hongkong
Model : TL-WDR3600
Hardware Version : V1
Firmware Version :
ISP :
When using the USB printer port share function, I found that some PCs, which had never physically connect to a USB printer before, will not have the virtual USB printer port in the port selection. In this way, TP-Link's USB printer controller will not be able to setup the connection. The PC will not be able to use the shared printer from my WDR3600.how can I create a virtual USB printer port in the remote PCs (without need to physically connect a printer to them) or other method to use the shared printer?
Region : Germany
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 3.13.26 Build 130129 Rel.59449n
ISP :
all my systems are configured under "IP & MAC Binding". Binding is activated globally and all check marks for every ID are set. After i finished my configurations, the "ARP List" status shows, that everything is bound - so far everything is great. The problem appears after a router reboot or after shutting the router down and powering it on again. The "ARP List" then shows only a few of my IDs and their status is unbound. I need to go back to the "Binding Settings" and hit "Save" - after that all my IDs appear in the ARP-List and everything is OK again.
Region : India
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : TL-WDR4320 router
ISP :
Just buy TL-WDR4320 router but its in Chinese language can somebody provide my English Firmware so that i can use this product.
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 3.13.23 Build 120820 Rel.73549n
ISP : Cable TV provider
It seems there is a bug with TL-WDR3600. As it can be seen in the following image, the UPnP is off:But my firewall on the computer is reporting flood of packets originating from the router (it's the routers MAC address and IP address):I don't know what ETH type packet is, 0026 might be hex (38 decimal as seen in the raw log). But port 1900 is definitely UPnP.At the router, the wireless switch is off, as well as all other options for sharing etc. This computer is the only one connected to the router. The router has been reset several times.
Region : Germany
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 120820
ISP : German university ISP
I have a big problem with several TP-Link routers (WDR3600, WR1043ND, WR741ND), always with the latest firmware and also with older ones. After a day or so, my internet & network connection will drop all of a sudden and all the routers need a reboot. There is no indication on what provoces these lock-ups. The routers can handle heavy traffic (bittorrent /w 100s of connections) but will stop working when browsing casually. The web-GUI will become unreachable. No pings to the outside are possible anymore, not even to direct IPs (8.8.8.8 for example). No pings to devices in the same network are possible either.
Region : UnitedStates
Model : TL-WDR3600
Hardware Version : V1
Firmware Version :
ISP : Centurylink
I'm using a WDR3600 router, and I'm having difficulty with getting internet access on the 5 GHz band. Right now the router is broadcasting in both 2.4 and 5 GHz as two separate APs. The 2.4 GHz band works perfectly fine, but when I connect to the 5 GHz band my device is not assigned an IP address and cannot connect to the internet (or even the router configuration page). Unfortunately, I don't have another device capable of accessing the 5 GHz band, so I can't check to see if the computer is at fault, but both the computer and the router have worked together with no problems before, and this computer has done fine in accessing other 5 GHz bands.
Region : Argentina
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP :
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 121225 Rel.37950n
ISP : Comcast
I just upgraded my DLink DIR655 to WDR4300. My VOIP service has worked for the last 5 years. But with WDR4300, I'm frequently experiencing dropped calls. The call will be cut off every 20 seconds or so. This is really a deal-killer.
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23
ISP : Comcast
I have no problems connecting on a 5 GHz band or wired to the router. However any device connecting on 2.4 Ghz gets barely any bandwidth and drops after running for a short time. I have test numerous devices and have the same issue. What was odd is a device on 5GHz that worked fine had the same issue when connecting on 2.4 GHz which seems to say it is only that band. I have an old router that works fine on 2.4 GHz on channel 1 with all the security settings I used on the 4300.
Region : UnitedStates
Model : TL-WDR4900
Hardware Version : Not Clear
Firmware Version :
ISP : Comcast
The internet connection works really well on the 2.4GHz connection and when wired. But when Im connected through the 5GHz network, I get no internet.
Region : Iraq
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP : Newroz Telecom
Can I replace firmawre TP-Link WDR4300 to DD-WRT to use it?, either my TP-link already has VPN,NAT,QOS,..etc like as DD-WRT so does need to replace firmware for better?
Does TP-Link WDR4300 support with DD-wrt? Is it working clearly without any problem?