I have spent two days on the phone with virgin mobile broadband where I bought the device and they do not know what I am talking about.First of all the mifi is working fine on the one and only computer I have set up so for..it is Vista operating system..I am trying to set up my vista computer as an FTP server on the mifi or wifi or whatever you call it.when I disable the DHCP service on this virgin mobile mifi device so that I can generate my own internal ip for this particular computer..It is not functioning that is I cannot connect to the internet..I tried to get from Virginmobile the DNS server address but they were confused...When I log into the device itself under advanced options it does allow for me to disable DHCP..but my problem is what IP do I use when setting up the wireless connections, I disengaged the automatic, but I am having a heck of a time trying to use the right IP then the gateway address and the DNS.
Both my DIR-655 and DIR-815, when setup as wireless access points, are unable to ping external IP addresses and thus cannot contact the dlink ntp servers. I've disabled UPnP, disabled DHCP, changed the LAN IP address to an available address on the network. The wireless works, devices are getting an IP from the network DHCP server and can surf the internet. But the DLink router itself cannot ping any external IP addresses. But the DLink router itself cannot ping any external IP addresses.
I'm looking to setup a few ip security cameras in my house and would like to monitor from work. The first thing I did was give the ip camera a static ip on my local LAN 192.168.1.104. I also forwarded port 9000 to this ip. I then went to [URL] to look up my external ip address. I was able to obtain one ip for my router and another for my modem (disconnected router and went direct through modem).
I've since tried to ping my router WAN ip from work numerous times via http://24.x.xxx.xx:9000 and I get timeout errors. I've tried traceroute and it gets close, but times out the last 3 hops. I've had Comcast on the phone many times trying to resolve and needless to say they weren't able to work.
I'm trying to setup my home network so that I can access it when away from home but I've ran into problems and I can't figure out what is causing the problem.I've setup the router to forward incoming requests on port 80 to be directed to my PC running WAMP. The PC has a static IP and if I access it from another PC on my network I get the WAMP page load as expected.I've also setup an account with no-ip.com to resolve my (dynamic) ip. If I use the address they have setup while I'm on my network I get the login page for the router, again this is what I expect.The problem begins when I try and access my home address (whatever.no-ip.biz) from outside my network. I've tried it from 2 different locations and via a dial-up account and I get nothing.
DNS resolution works and I can surf the web without fail. But if I try to ping any external hosts (I can ping inside interface of ASA fine) from the LAN I get timeouts. I can ping anything from the ASA without fail.
I've had some issues with my 892 router. [code] When match address is set to acl-net12, I can't ping my router on external interface and tunnel is working very bad (15%-20% packet loss).If I change match address from acl-net12 to acl-net12-new then I can ping my router on external interface and vpn si working fine.
I have also an acl (set on external interface) which allow ping but it seems that is not working when acl-net12 is used on crypto map. [code]
I have setup a new RV180 and it appears to be connected to the WAN, however, I cannot ping the external IP. In some of the documentation, there are references to default access rules, however, there does not appear to be any rules setup. What other settings need to be made to allow the firewall to be pinged on the WAN interface?
I've configured a 5505 but internal clients can't ping external ip. To test I've connect a pc with the ip of the default router on the Outside int the ASA can ping the PC and the PC can ping the ASA, but internal clients can't ping the PC
PC config 195.12.23.241/28
Here's the ASA config, so far I've wiped the ASA and started with a blank sonfig and built it up but still not working.
As a raw test it is handy for us to ping externally the WAN port of the SRP 527W. How we configure the SRP 527W to allow this? FYI we have the inbulit SRP firewall enabled.
I have a 1760-v router set up at my home lab and I am unable to access IP addresses outside my local network. I have my Cisco router's fast Ethernet port connected to a small net gear router which then connects to my cable modem. The Cisco router is able to ping local address fine, but when I try to ping an outside address or domain name it times out. However, when I am at the CLI and type something like Ping { URL}, it resolves Google's IP address but it will not ping it. I have IP DEFAULT-GATEWAY and IP NAME-SERVER both pointing to my net gear router and pointing to my ISP's DNS server.
I would like to add a second mifi 2200 to my current contract. (Same phone # & same bill.) That way I can use the second one while I'm on the road & my wife can use the first one at home!
Just bought a verizon 4g mifi.The laptop hooked up in a second to the device but i cant get my desktop computer to detect the connection.I tried using a USB Linksys wireless adapter then tried a netgear g-router but neither detect anything.
I am trying to setup an RV016 router to do "1 to 1 NAT". I am starting with setting the external IP address of my RV016 to 10.8.58.219 on the WAN1 port, and LAN IP 10.10.20.254. Simple enough. When I connect my laptop to port1 on the router's LAN side I can ping the router's external AND internal IP addresses fine; But I can not ping from outside when connected through WAN1 port.I am performing a simple local test with an external hub, I put a patch cable from WAN1 port to the hub, another patch cable from port 1 on LAN side to the same hub, and from my laptop to the hub. When I use my laptop's IP address with the internal schema (10.10.20.100 for example) I can ping both WAN1 and LAN IP's; but when I use on my laptop the external IP schema (10.8.58.100 for example) I can not ping it. Therefore is not working when I connect my router to the real network.I went into the web setup pages of the router and dissabled: firewall and basicaly all security "blocks" it has, and leave it open for my testing.
I have some issues with router configuration. I cannot open any external web pages, but ping or telnet is just fine. Im using router-on-a-stick scenario. Router connected to LAN trough EtherSwitch module. Config attached.
We have a Cisco 871W working as PIX, controlling external VPN connections to our private network.The configuration is very similar to the one described here - "Cisco Router as a Remote VPN Server using SDM Configuration Example" url...
About once a week, it stops working, without aparent external intervention.The ping to the external IP stops answering, and the internal IP stops answering pings also.The solution is power-off and power-on, and it starts working again ...
What is the correct way to debug this situation ?I can connect a HyperTerminal using direct cable to the 871, but dont know the relevant commands to debug this situation.
Is there any LOG I can have a look into ? Yes, I am quite new to Cisco world .By the way : "show version" says Cisco IOS Software, C870 Software (C870-ADVSECURITYK9-M), Version 12.4(15)T7, RELEASE SOFTWARE (fc3)
I have installed quite recently a cisco ASA 5520 replacing a linux based firewall I have only 2 zones ..one is internal netowrk and other external the internal network has web servers, dns and mail server all having public IPs Every thing is OK but i have seen that if I try to ping an external server for example [URL] i cannot ping says
but I can ping from systems which are outside my firewall perfectly with the linux firewall i had before i could ping perfectly to yahoo from any of my internal servers?
I am trying to use a MIFI hotspot for the internet, I have a wifi laptop, and a wifi printer.I would like to print wirelessly from my laptop and use the internet at the same time, but I can't. To print I have to go to my wireless network and switch to my router. And if I want to use the internet I have switch my wireless network back to the MIFI hotspot.
I have a Verizon MiFi card and 3 wireless laptops that pick it up automatically.....I can't seem to get it set up on the desktop pc.....it doesn't recognize it
I have the WPC54G , used on Sony Vaio, Windows XP Home Edition Version 2002 and use a Novatel Wireless MiFi 2200 Mobile Hotspot. Recently had system crash--reinstalled through recovery discs and all current Windows Update (SP3), as well as the WPC54G The WPC54G worked with various WiFi Networks and the MiFi2200 Device before crash. After "recovery", it recognize WiFi Networks, however; it does not recognize my network established through the Novatel Wireless MiFi 2200 Device. (Note: the MiFi Device is working because other computer/devices are gaining access to internet.
If theres a way, one of you guys could find it. I bought one of these and managed to bridge the wireless and lan connections so I can use my xbox360 on it but it says my experience will be limited due to strict NAT. I tried virgin mobile customer service and they were useless.
I need to figure out how to connect my home router to my AT&T MiFi. I have 3 DVD players and one computer hard wired to the router. The MiFi works great with my laptop and IPad that has wireless capability but how can I get it to connect to non-wireless devices connect to my router?
My Verizon MiFi can't recognize my Toshiba laptop. The laptop recognizes the Verizon MiFi, but won't accept the password. Toshiba wants $159 to fix this.
MIFI 2200 works with the USB connected to the computer but, won't transmit to another computer.It is a desktop. So I put in a wireless card. It will identify that the network is there but, will not access it. Is there a difference between what a desktop wireless card will access and what a laptop or mobile device will talk with.There seems to be because the MIFI will connect to a Droid and a laptop but, not to the desktop I want it to.Is there a different card or some kind of USB thingy that I can use to make the two devices talk.
Additional:
MIFI is a verizon cellular product to connect up to 5 computers.It will work when plugged in directly but, not when it has to use the wireless card.The computer I want to connect has a wireless card and will recognize the network but, won't connect. It is a desktop, not a laptop or mobile device.Turns out that you can buy a WiFi adapter in a USB plug and play device for a newegg price of 7.99 dollars to a high price of about 150 bucks.Is there any card that I can put inside the computer so I can make this permanent?
I've got the Verizon Jetpack MiFi and cannot figure out how to create a bridge with a D-Link DAP-1513 to get internet. Eventually this setup will be connected to a DVR but for now I'm trying to use it on my laptop to make sure it's going to work. I don't have networking experience and have been trying to figure this out for almost 2 weeks now.
Background information, have had the 4150L for probably about a year and haven't had a bit of trouble with it. I just updated the firmware this morning and it still seems to be working great. This is the first upgrade I have ever done to it. Anyway, what I am trying to accomplish, I have discovered that I can remotely connect to my office computer through my iPad using itap RDP and a VPN connection. I have already been able to use itap RDP in the office to show patients their x-rays etc... on the iPad. I have a cisco RVO82 router and my office software suggests the use of a PPTP VPN to connect remotely. I have checked all the settings and I have everything set as described. The iPad shows a VPN connection icon but when I try to connect to my computer, I get a TCP error. From what I have read, some people are able to connect via VPN on the 4150L and others are not.
I have recently moved to a remote area and am using a verizon Jetpack 4620L as an internet connection.I would like to continue using my Airport Extreme in bridge mode to extend my network and to also use my wireless printer and scanner easily.
I have a new 3560G to set up a small network for a remote site. I configured the vlan and an SVI as the gateway. The switch is also the DHCP server for the LAN. I configured Gi0/2 as L3 port, connecting to the nearest neighbor. My network runs EIGRP so i advertised the routes into the EIGRP process. The switch forms EIGRP neighbors and learns all routes in the enterprise network. The problems I'm having now are: 1. The switch learns all routes in my enterprise LAN and can ping devices in the enterprise LAN, but I can’t ping any interface on the switch from the enterprise LAN. 2.
I set this up and I can ping all the gateways but never the hosts. I was hoping I could make these links between 6500's a mix of L2 and L3. Check it out. They are connected in a linear fashion R1--->R2--->R3. I can ping from R1 to R3's SVI4 gateway but I can never ping a host on that SVI4. I was hoping that I could use the port-channels between 6500's as routed links or as trunk links depending on the type of traffic....thought it would ease the migration. I suppose I could always get rid of the port-channels and just make separate L2 and L3 links between the 6500's.
From My Router that connects to Cable modem i am unable to ping website 4.2.2.2I am able to ping all other websites fines.Same website i can ping from my pc and all other switches fine.Router has only 1 ACL thats for NAT.
