I just upgraded my router from the WRT54GL to the EA6300, and it appears there is less coverage with the new unit. Previously, my neighbor could share my router and now with the EA6300 my phone switches to 4G at the end of the driveway. Has anyone seen any specs which publish to output of the ea6300?
View 3 RepliesWhy my OC3 interface is showing increasing output drops its starts happening as soon traffic exceed 60Mbps ( FYI my traffic never exceeded 75Mbps MAX, and circuit is 150Mbps from carrier , full OC3)
Below are few stats as starter. IOS i am using is c7200p-is-mz.122-31.SB10.bin
sh int pos1/1
POS1/1 is up, line protocol is up
Hardware is Packet over Sonet
[Code].....
i just bought the E4200v2 and configured for my network. the router found the latest firmware and has been updated. i tried multiple configurations/channels etc with no change.basically, coverage is horrible, and even when in the same room as this router copying files from a linux server and a window7 machine is extremly slow.... almost as if its G speed. my mac is showing the transmit rate >108mbps and should be copying at 60,70 even 80 mbps (megabits), but im getting on average ~28mbps however, uploading from my mac to those 2 machines flys. im seeing speeds at 80 to 90 mbps, which is again, what i would expect.
View 3 Replies View RelatedPlugging directly into the university's network I get a solid consistent ping to any website. This might be 10ms to google, or 5ms to something really close - but the point is its bang on exactly the same every time.However when I pugin the EA6500 and use the internet via the router the pings go crazy.
30
25
21
27
18
29
15
20
20
14
21
etc, no longer consistent and between 2-3x higher. I've turn off all firewalls and filtering that I can see on this router, but it seems absolutely crazy I've paid close to £200 for something that just destroys my ping?
Is this the best way to get maximum performance and coverage? I have a DIR-655 bridged to supply B/G on channel 11.I Gave Up On Linksys Firmware And Installed DD-WRT.
View 4 Replies View RelatedI had an old LINKSYS WRT54GS whihc had a poor coverage of my whole home.I just bought a new E-3200 which is supposed to have a real higher coverage but seems not.When I am in a room at 15m from the routeur, no coverage !How can we optimize the coverage of the routeur ?
View 5 Replies View RelatedMy DSL Modem connected right now to Linksys Model: WRT600N (Dual Band Wireless-N Gigabit Router) to give a wireless internet access in my house. I have TWO spare Linksys Wireless Router (WRT350N-Wireless-N Gigabit Router) and (WRT54G2-Wireless-G Broadband Router) that I need to use to expand my wireless network at home.
How can i connect the two routers to became an access point or range expander to existing router. It is possible the two spare routers became an access pt or expander? How can i configure that? Cable configuration?
Both use the same encryption (WPA2-Personal), same channel and they are tested in the same location with g-only mode. Only one router is switched on at any one time during the test. When 3 g-client notebooks (of various brands) are associated with the E4200, the signal indicator is a single bar, wherelse they can get 3 bars with the WRT54G (in the same location). For Internet speed test on a 20Mbps link, WRT54G is able to substain about 10Mbps, but only 1-2Mbps with the E4200.
Is such difference in performance between the two router models normal? Is there any configuration required to tweak the E4200? Or is it a hardware related issue with E4200?
The E4200 has been updated with the latest available firmware as of yesterday.
we are currently using a modem router LINKSYS WAG120N Wireless-N ADSL Router but are not satisfied. lots of dead zones and I think that there are too many users for this AP. last count gave around 20 users. so I'm looking for a solution to be able to handle 20+ concurrent connections and with large coverage - 600 m² .
View 7 Replies View RelatedI have 2 story house and trying t extend wireless coverage in the house. I have have 2 routers. One is just wrt54g while the second dual mode EA-4500. Cable modem is located in the basement so i would like to have one of the routers connected to it and use another router as bridge. So which router would be best to use a bridge. If i use ea4500 as a bridge then i would lose dual band features of it.
View 9 Replies View RelatedI recently bought a e4200v2 router and installed it by connecting it with my old modem d-link 2730u.I was disappointing to see that the new router i.e e4200v2 has the exact same coverage as my old router which is costing about 35 usd and linksys cost about 200 usd.. this is a terrible waste of money!!
View 1 Replies View RelatedI setup a WRT120N router in my home. I am having a issue getting good coverage over my single floor ranch style home. Would changing the Standard Channel (currently set 6) make a difference?
View 9 Replies View RelatedI bought two E4200s with the intent of using the second as a wireless access point to maximize coverage throughout my house. I just learned the hard way that the E4200 doesn't support that feature, and will only act as an access point if physically connected to the primary router that is connected to the internet.
Before I spend even more money on equipment, I was wondering if any of the experts here can tell me whether I can use a Linksys Bridge, like the WET610N or WES610N, to operate the second router in bridge mode and turn it into a wireless access point?
My wireless router has been spotty since my cable company installed a new modem for cable internet. I have powercycled several times, downloaded new firmware, rebooted and am still having problems. Lately when I do finally get on the internet with a wireless device, the signal strength is very low. It is low on my iphone, on my Mac laptop and also on my Samsung Bluray player. Lately a window keeps popping up when I am trying to watch netflix that states my band width is too low, even though it has been working fine for 2 months. Is my router outdated?
View 5 Replies View RelatedCurrently I'm using one e4200 (v1) as my main router in the house. The wireless coverage downstairs is perfect, but upstairs the signal is weak. To improve this I thought about adding the WAP610N as an access point to my network. But this device gets quite some negative reviews ... Thus I was thinking why not add another e4200 (v2) to my network? The price difference is not that big, especially compared to other simultaneous dual band access points. So my question is, would following scenario work?
- first e4200, connected to my ISP, acting as a router, using both the 2.4 as 5 ghz band (basically my current situation)
- second e4200, connected (via UTP cable) to the first e4200, in bridge mode
- second e4200 also using both 2.4 and 5 ghz band, using the same SSID, security etc but a different channel
So when moving a laptop for example from downstairs to upstairs, automatically the router/access point with the strongest signal would be used.
We have a new e1000 router that was having trouble reaching the TV for Netflix movie streaming. Too many walls and too much distance. A simple solution was to direct the signals from the router by placing aluminum foil behind the router so all the signal was going towards the TV rather than in an 360 degree circle. Now the streaming works great! After the movie is done I remove the foil and everything looks just like it should.
View 9 Replies View RelatedI have a new e3000 series router and on all pc's I'm using model AE1000 receivers. Now, the laptops we use work great until we go out to a room built off the main house (a seasonal porch)
View 2 Replies View RelatedI have configured a new LinkSys e3000 as as wireless router in our house.I have left the configuration as default (only secured it and turned on the DHCP server).I have only turned on the 2,4 GHz network ( because the 5GH had an even shorter range).Everything works and all my devices can connect to the router and access the internet.However i find the signal strenght of the router to be very poor.Already in the next room it drops to 60%. And in some rooms on the 1st floor the signal drops completly.This happens not even 20m away from the router in an ordinary "family house".Is there a setting somewhere which could increase the signal strength ?I noticed that the router has no antenna, can one be bought and attached so the signal increases ?The firmware version is 1.0.02 and i found a newer on your web 1.0.03. How to improve the signal strength?
View 6 Replies View RelatedI have a two story house with a basement. Right now I have a Cisco Linksys E4200 router on the second floor in one of the bedrooms. I have a DLink GamerLouge 4500 in the basement. Both systems have the same SSID and are running on different channels. Computers connect to the appropriate one automatically. At least assuming that's what's happening.I am getting limited connectivity on the first floor in the kitchen and family room. Dining room, right by the second floor stairs is fine. All the bathrooms are dead zones. Note I have thick travertine tiles on the walls in the bathrooms so may inhibit signals. Trying to figure out the optimal solution for getting the house setup so everywhere has at least decent signals. I have alot of iPad and laptop devices floating around the house so wireless is key. Note I have wired plugs with Cat5e all over the house to a central hub in the basement which is where the DLink router sits. Thoughts on how to improve my signal strength? Especially in the farther reaching bedrooms and the first floor
View 4 Replies View RelatedFor some reason my ps3 wont connect,the signal strength is 100% but it just times out.it will randomly connect BUT cant stream anything or connect online.Or it will get disconnected if someone turns on my mine computer in the other room/Should i DMZ the ps3?Routers a WRT610N dual N Firmware Version: 2.00.00 B05 cant upgrade to 3.00 because of "upgrade failed" error.
View 9 Replies View RelatedWhat signal strength should I expect when in the same room as the e4200 ?I'm checking signal strength with iStumbler and with option-right click on airport menu icon on my Mac.I'm getting a signal strength of about -55 while in the room with the router.What signal strength should I expect while in the same room, no physical obstructions, etc. ?
View 6 Replies View RelatedI went out and bought a e4200 today and the signal strength is worse than my WGT300n, is there any tweaks I can do to expand my signal strength?
View 3 Replies View RelatedI have a WRT54gh, and the signal strength is extremely poor. Full strength at about 15 centimeters, Then drops to 50% at 50 centimeters. By 1.5 meters, the signal is extremely weak or not visible. Have updated to the latest firmware, factory reset and power cycled. There are no other wireless networks or devices that would provide interference Have experimented with channels, thresholds, transmit type, encrypted/open, intervals etc..No luck. Due to signal dropping off so quickly it seems like a transmit strength issue rather than an issue that can be solved in the menu. I'm wondering if there's a way I can console log-in to the Linux kernel and check the transmit strength and perhaps bump it up by a few DB? It's out of warranty so a solution involving opening the case is also acceptable.
View 9 Replies View RelatedI have been disappointed by the range of the EA4500 compared to previous routers, but I am most puzzled by it's behavior. I may get an "excellent" connection close to the router (one room away) and speeds up to 65 Mps, but after a few minutes of surfing the web the signal strength and speed can drop substantially.
The problem is the worst at a distance (one floor down in our house, maybe 30 feet away in total) where the signal strength may start at "good" and a speed of perhaps 30 Mps, but then after 3-4 minutes drops to "poor" and maybe 5 Mps.
Have two WRT54G Wireless Routers.
-One WRT54G ver. 6, Firmware Version v1.028
-One WRT54G ver. 6, Firmware Version v2.x
With the WRT54G ver. 6, Firmware Version v1.028.When I ran the android app WiFi Analyzer, I get mixed results.On my Samsung Galaxy S3, I saw my signal on Channel 2, and others around me (two on Channel 6 and two on Channel 11).On my ASUS Transformer Prime TFT201 I see the same signals, but my router signal bounces continously between the baseline (-100dBm?) and about -35dBm.
Plugged in the WRT54G ver. 2, Firmware Version v2.x Channel 8.Hooked it up and got good steady signal strength. It Had 'WPA - Shared Key' but did not have the 'WPA - Personal' that was on the ver. 6. So, I had to go and screw things up. I've upgraded this to Firmware Version: v4.21.5 and guess what? I now have 'WPA - Personal'. I also have a signal is bouncing on BOTH units.
On my ASUS, I can see both routers. The ver. 2 AND the ver. 6 are bouncing between baseline and -35dBm, in unison. Apprently something in the ASUS does not like the later Firmwares.On my Samsung I can see the two signals - the ver. 2 on Channel 8 is stable as a rock and the ver. 6 on Channel 2 is also bouncing, but at a much slower rate! Running Speedtest.net a PC hardwired to the ver. 2 - I get 5.34 Mb/s Download and 0.47 Mb/s upload (yeah, my Internet sucks!) Running Speedtest.net through the ASUS/WiFi to the ver. 2 - I get 2.43 Mb/s Down and 0.65 Mb/s Up.Running Speedtest.net through the Samsung/WiFi to the ver. 2 - I get 5.07 Mb/s Down and 1.07 Mb/s Up.
Just got an E2500 and installed it with no problems and it was working correctly for 1-2 days. This evening the signal strength of my SSID dropped to LOW and a new SSID now shows up with full signal strength. It s not an SSID from any of my neighbors and from checking several forums it appears this is known problem.
View 2 Replies View Relatedcould it the wireless ADSL modem + AP (e.g., WAG54G) coverage the wireless adapter.If answer is negative, then if both (wireless modem & wireless adapter), close to window, how?Again, if answer is negative, then may via Detachable Antenna of any devices that install out of window builds?
View 2 Replies View RelatedI have a Linksys wireless router in my basement and I want to extend coverage upstair. I have a office upstairs which has a ethernet cable that is plugged into my router in the basement, can I connect a Linksys Wireless G WAP54G access point to that ethernet cable and thus have a extender upstair?
View 1 Replies View RelatedI'm using a router WAG320N in my home but now i need to expand my lan with another ports and wireless coverage.In a wired point (connect directly to the router) i need 3 ehternet ports and a repetear of a wireless signal.The optimal solution woulb be a switch gigabit with an integrated acces point, but I understand that there is no such thing...So going to buyng the switch SE2500 and the AP WAP610N... but then I realized the existence of the bridge WES610N!But the information on the linksys italian site is not enough and the relative page does not works... i need to now if this object can take a wired lan replicate it in 3 ports and expand the wireless network of my router.
View 5 Replies View RelatedI have a linksys router,I reset it and hooked it up,but I don't get internet even though the signal is excellent
View 1 Replies View Relatedbelkin n wireless router minimum coverage ?
View 1 Replies View RelatedMy brother has a router for his house which lives right next door. I am getting wireless through a adapter right now but not good throughout my house.
View 1 Replies View RelatedI have a WET610N on my network with very little signal strength. My set up is:
Router E3000
48 ' (48 feet) to
WET610N
The WET610N is on 5Ghz N, and is the only device at Ghz, and indeed the only wireless device during testing.
The use for the adaptor is to connect an Xbox 360 as a MCE for Video streaming.It is unusable, with unwatchable lags and intermittent failures.The 'Network Performance Monitor" doesn't read in mb/s, but essentially I get about 1 or 2 'bars', well under the acceptable for Standard def reading.
zInterestingly, when I bring the device within 3 feet of the router, I get great speeds (30 Mb/s down), but the bit rate reading in the status screen reads lower than the below reading.
Below is at the 45 foot mark->
Link Status:Connected MAC Address:68:7F:74xxxx:31 Network Name (SSID):sx BSSID:98:FC:11:xxxx9:94 Radio Band:5 GHz Channel Width:20 MHz Wide Channel:N/A Standard Channel:36 Bit Rate:43.3Mbps Signal:10% Security:WPA2 Personal