Linksys Wireless Router :: WRT54G Signal Strength Bounce After Firmware Upgrade
Dec 10, 2012
Have two WRT54G Wireless Routers.
-One WRT54G ver. 6, Firmware Version v1.028
-One WRT54G ver. 6, Firmware Version v2.x
With the WRT54G ver. 6, Firmware Version v1.028.When I ran the android app WiFi Analyzer, I get mixed results.On my Samsung Galaxy S3, I saw my signal on Channel 2, and others around me (two on Channel 6 and two on Channel 11).On my ASUS Transformer Prime TFT201 I see the same signals, but my router signal bounces continously between the baseline (-100dBm?) and about -35dBm.
Plugged in the WRT54G ver. 2, Firmware Version v2.x Channel 8.Hooked it up and got good steady signal strength. It Had 'WPA - Shared Key' but did not have the 'WPA - Personal' that was on the ver. 6. So, I had to go and screw things up. I've upgraded this to Firmware Version: v4.21.5 and guess what? I now have 'WPA - Personal'. I also have a signal is bouncing on BOTH units.
On my ASUS, I can see both routers. The ver. 2 AND the ver. 6 are bouncing between baseline and -35dBm, in unison. Apprently something in the ASUS does not like the later Firmwares.On my Samsung I can see the two signals - the ver. 2 on Channel 8 is stable as a rock and the ver. 6 on Channel 2 is also bouncing, but at a much slower rate! Running Speedtest.net a PC hardwired to the ver. 2 - I get 5.34 Mb/s Download and 0.47 Mb/s upload (yeah, my Internet sucks!) Running Speedtest.net through the ASUS/WiFi to the ver. 2 - I get 2.43 Mb/s Down and 0.65 Mb/s Up.Running Speedtest.net through the Samsung/WiFi to the ver. 2 - I get 5.07 Mb/s Down and 1.07 Mb/s Up.
View 6 Replies
ADVERTISEMENT
Oct 16, 2011
My wireless router has been spotty since my cable company installed a new modem for cable internet. I have powercycled several times, downloaded new firmware, rebooted and am still having problems. Lately when I do finally get on the internet with a wireless device, the signal strength is very low. It is low on my iphone, on my Mac laptop and also on my Samsung Bluray player. Lately a window keeps popping up when I am trying to watch netflix that states my band width is too low, even though it has been working fine for 2 months. Is my router outdated?
View 5 Replies
View Related
Dec 22, 2011
My Linksys WRT54G router has been dropping out lately and I've been recommended to update its firmware as it is very out-of-date. Well, everytime I try to upgrade the firmware to it, I get an error message that says "the connection to the server was reset while the page was loading." I'm trying to upgrade the firmware through the router's site 192.168.1.1 under the adminstration tab
View 2 Replies
View Related
Feb 10, 2012
I am trying to upgrade the firmware, your web site requires the version number, my version is V8, your site offers up to 7.2 ?
View 2 Replies
View Related
Aug 24, 2012
I have a wrt54g (8.1) that was acting a little funny so did some googling and followed the instructions to install new firmware. First the installation failed, double checked to make sure I downloaded the correct file (FW_WRT54G_8.1.09.02_US_20071227.bin), did a reset and power cycle. Checked the information again and everything on the router setup completely disappeared.
View 8 Replies
View Related
Mar 10, 2013
I have tried to upgrade the firmware to the latest greatest but keep getting the "Incorrect image file" error. I bought two of the V1 units and had no trouble with one of them but the other is frustrating me. I have reset it and even tried a tftp upgrade of the firmware but still get "Incorrect image file" even in tftp.
View 1 Replies
View Related
Nov 24, 2011
I have an old wrt54g (version 2) which I just downloaded and installed the latest firmware (4.21.4) and now its dead!!!!
factory reset does nothing, cannot connect via a wired connection, nothing. All the lights work fine.
View 4 Replies
View Related
Feb 28, 2013
just troed to update FIRMWARE re our WRT54G_v2
current FIRMWAREFirmware Version: v3.37.7
downloaded and tried to run 130228dl_LINKSYS_FW_WRT54Gv4_4.21.5.000_20120220.bin
BUT got msg' Upgrade are failed!;
View 3 Replies
View Related
Jul 19, 2011
I ran the firmware upgrade and hit the reset button for 30 seconds and everything went well until I went to restore my personal settings. When I went to the router page it asked for a user name and password but the old user name and password don't work so I am locked out and can't get to the restore page.
View 3 Replies
View Related
Dec 5, 2011
I'm attempting to upgrade to firmware 5.00.38 for my WRT54G-TM router, but it keeps telling me "upgrade failed" after like 3-4 seconds of trying. It says I currently have firmware: DD-WRT v24-sp2 (06/13/09) mega - build 12288. I've tried restetting to factory defaults before upgrading
View 3 Replies
View Related
Feb 2, 2013
I tried to upgrade firmware (I entered my model number WRT54G and hardware version 2 into Cisco menu and downloded the upgrade file they provided. My version was v2.02.7, downloded file FW_WRT54Gv4_4.21.5.000_20120220.bin . After I run the upgrade it said upgrade failed. After that I can't connect to internet and can't access the router. I tried to reset it and unplug it- no luck. From my PC control panel I see local area connections status connected, but as I said, it does not connect to Internet.
View 7 Replies
View Related
May 16, 2012
I'm currently trying to upgrade my linksys WRT54G v1.1 router using the WRT54G-EU_fw,0 file, however when I press upgrade it comes up with a message saying "Incorrect Image File!". The current firmware version is v1.42.2 Is there any way to fix this so I can upgrade it?
View 4 Replies
View Related
Aug 29, 2012
I have a problem with my WRT54G V8 router.I download a wrong Firmware and upgrade it.After this my router never work again.The PC can't get IP from the router.I tried a lot of time to access to the web admin 192.168.1.1 and other IP and nothing happen.I made a lot of reset cycles, with the procedures 30/30/30 or other with the reset button in combination with the power cord.
Exist any other possibility to recover my router.Can I open and touch other button inside the board or something like this?
View 9 Replies
View Related
Sep 22, 2011
I was in the process of upgrading the firmware on my Linksys WRT54G router when a connection interruption occurred. Now, the router will not boot up and I cannot communicate with it.Is there a way to reset the firmware?
View 2 Replies
View Related
Oct 5, 2011
i have a linksys wrt54g ver6 router. i want to upgrade the firmware. so i went to dd-wrt.com typed in my router. then i found it on there list, selected it and upon reviewing it, it sucked ram 8mb flash 2mb. looking through the linksys versions, ver2 was the best one ram 32mb flash 8mb. so can i use ver2 firware on my ver6 router?
View 1 Replies
View Related
Sep 24, 2012
Currently I'm using one e4200 (v1) as my main router in the house. The wireless coverage downstairs is perfect, but upstairs the signal is weak. To improve this I thought about adding the WAP610N as an access point to my network. But this device gets quite some negative reviews ... Thus I was thinking why not add another e4200 (v2) to my network? The price difference is not that big, especially compared to other simultaneous dual band access points. So my question is, would following scenario work?
- first e4200, connected to my ISP, acting as a router, using both the 2.4 as 5 ghz band (basically my current situation)
- second e4200, connected (via UTP cable) to the first e4200, in bridge mode
- second e4200 also using both 2.4 and 5 ghz band, using the same SSID, security etc but a different channel
So when moving a laptop for example from downstairs to upstairs, automatically the router/access point with the strongest signal would be used.
View 2 Replies
View Related
Nov 29, 2010
We have a new e1000 router that was having trouble reaching the TV for Netflix movie streaming. Too many walls and too much distance. A simple solution was to direct the signals from the router by placing aluminum foil behind the router so all the signal was going towards the TV rather than in an 360 degree circle. Now the streaming works great! After the movie is done I remove the foil and everything looks just like it should.
View 9 Replies
View Related
Jul 6, 2011
I have a new e3000 series router and on all pc's I'm using model AE1000 receivers. Now, the laptops we use work great until we go out to a room built off the main house (a seasonal porch)
View 2 Replies
View Related
Nov 26, 2010
I have configured a new LinkSys e3000 as as wireless router in our house.I have left the configuration as default (only secured it and turned on the DHCP server).I have only turned on the 2,4 GHz network ( because the 5GH had an even shorter range).Everything works and all my devices can connect to the router and access the internet.However i find the signal strenght of the router to be very poor.Already in the next room it drops to 60%. And in some rooms on the 1st floor the signal drops completly.This happens not even 20m away from the router in an ordinary "family house".Is there a setting somewhere which could increase the signal strength ?I noticed that the router has no antenna, can one be bought and attached so the signal increases ?The firmware version is 1.0.02 and i found a newer on your web 1.0.03. How to improve the signal strength?
View 6 Replies
View Related
Oct 29, 2012
I have a two story house with a basement. Right now I have a Cisco Linksys E4200 router on the second floor in one of the bedrooms. I have a DLink GamerLouge 4500 in the basement. Both systems have the same SSID and are running on different channels. Computers connect to the appropriate one automatically. At least assuming that's what's happening.I am getting limited connectivity on the first floor in the kitchen and family room. Dining room, right by the second floor stairs is fine. All the bathrooms are dead zones. Note I have thick travertine tiles on the walls in the bathrooms so may inhibit signals. Trying to figure out the optimal solution for getting the house setup so everywhere has at least decent signals. I have alot of iPad and laptop devices floating around the house so wireless is key. Note I have wired plugs with Cat5e all over the house to a central hub in the basement which is where the DLink router sits. Thoughts on how to improve my signal strength? Especially in the farther reaching bedrooms and the first floor
View 4 Replies
View Related
Jan 5, 2010
For some reason my ps3 wont connect,the signal strength is 100% but it just times out.it will randomly connect BUT cant stream anything or connect online.Or it will get disconnected if someone turns on my mine computer in the other room/Should i DMZ the ps3?Routers a WRT610N dual N Firmware Version: 2.00.00 B05 cant upgrade to 3.00 because of "upgrade failed" error.
View 9 Replies
View Related
May 7, 2012
What signal strength should I expect when in the same room as the e4200 ?I'm checking signal strength with iStumbler and with option-right click on airport menu icon on my Mac.I'm getting a signal strength of about -55 while in the room with the router.What signal strength should I expect while in the same room, no physical obstructions, etc. ?
View 6 Replies
View Related
Aug 20, 2011
I went out and bought a e4200 today and the signal strength is worse than my WGT300n, is there any tweaks I can do to expand my signal strength?
View 3 Replies
View Related
Oct 7, 2011
I have a WRT54gh, and the signal strength is extremely poor. Full strength at about 15 centimeters, Then drops to 50% at 50 centimeters. By 1.5 meters, the signal is extremely weak or not visible. Have updated to the latest firmware, factory reset and power cycled. There are no other wireless networks or devices that would provide interference Have experimented with channels, thresholds, transmit type, encrypted/open, intervals etc..No luck. Due to signal dropping off so quickly it seems like a transmit strength issue rather than an issue that can be solved in the menu. I'm wondering if there's a way I can console log-in to the Linux kernel and check the transmit strength and perhaps bump it up by a few DB? It's out of warranty so a solution involving opening the case is also acceptable.
View 9 Replies
View Related
Aug 30, 2012
I have been disappointed by the range of the EA4500 compared to previous routers, but I am most puzzled by it's behavior. I may get an "excellent" connection close to the router (one room away) and speeds up to 65 Mps, but after a few minutes of surfing the web the signal strength and speed can drop substantially.
The problem is the worst at a distance (one floor down in our house, maybe 30 feet away in total) where the signal strength may start at "good" and a speed of perhaps 30 Mps, but then after 3-4 minutes drops to "poor" and maybe 5 Mps.
View 4 Replies
View Related
Jan 27, 2012
Just got an E2500 and installed it with no problems and it was working correctly for 1-2 days. This evening the signal strength of my SSID dropped to LOW and a new SSID now shows up with full signal strength. It s not an SSID from any of my neighbors and from checking several forums it appears this is known problem.
View 2 Replies
View Related
Mar 12, 2012
I have a linksys router,I reset it and hooked it up,but I don't get internet even though the signal is excellent
View 1 Replies
View Related
Jan 27, 2011
I have a WET610N on my network with very little signal strength. My set up is:
Router E3000
48 ' (48 feet) to
WET610N
The WET610N is on 5Ghz N, and is the only device at Ghz, and indeed the only wireless device during testing.
The use for the adaptor is to connect an Xbox 360 as a MCE for Video streaming.It is unusable, with unwatchable lags and intermittent failures.The 'Network Performance Monitor" doesn't read in mb/s, but essentially I get about 1 or 2 'bars', well under the acceptable for Standard def reading.
zInterestingly, when I bring the device within 3 feet of the router, I get great speeds (30 Mb/s down), but the bit rate reading in the status screen reads lower than the below reading.
Below is at the 45 foot mark->
Link Status:Connected MAC Address:68:7F:74xxxx:31 Network Name (SSID):sx BSSID:98:FC:11:xxxx9:94 Radio Band:5 GHz Channel Width:20 MHz Wide Channel:N/A Standard Channel:36 Bit Rate:43.3Mbps Signal:10% Security:WPA2 Personal
View 1 Replies
View Related
Jul 21, 2010
I have a Linksys E1000 router. The macbook is getting great signal even out in the yard. The PC running Windows 7 and using an AE1000 wireless adapter is only getting 2 bars out of 5. I don't think there's any interference. I can't figure out why the signal strength is so poor.
View 5 Replies
View Related
Jul 17, 2010
I've noticed something interesting, after having been disconnected from the WLAN in less than 1 minute in my first experience with this Linksys' Modem Router: The signal strength was poor when browsing the Wireless LAN. I was at home, in a room just beside the one where the router was placed at.So, I took a look at connection status, and saw the signal strength was Medium - Weak: something around 30% and 55% You could think it was due to mirrors, the kind of walls between the rooms, and everything else, but I instantly remembered when browsing WLAN from the same place but not with the same router, the signal was strong (100%)...but I let it alone In the other day, while browsing WLAN, I've noticed another thing, this time visible: "TX power" I've got in connection status was 39mW, while I was almost sure it should be 100mW, based on my past WLAN connections Then, today I decided to take a look more deeply in that, and unboxed my Linksys' WRT54G to test. The test was carried on consisting in both Wireless routers placed in the same room, and a solid wall was between me and the routers.I could connect to the two WLANs, but the status of connections were different.
WAG120N:
WRT54G:
As you can see, when connecting to WRT54G , signal reached 100% at some point, whereas in WAG120N , such a mark wasn't possible.Of course, the signal strength was unstable in both routers, but the average level in WRT54G WLAN was greater, being most of time over 90%, and never below 80%.In WAG120N WLAN, average was 82%, and lowest level was 55%.When I went to the room where the routers were at, and right in front of them, no need to say both reached 100%, but as you can see, in WAG120n's case, TX power was still 39mw: I believe it's a firmware fault, once all other routers I've connected to always showed TX power as being 100mW.It shoundn't be related to the general hardware, as Cisco products are high-quality ones.
View 9 Replies
View Related
Jan 2, 2012
I have the following problem:
Adapter: WMP600N
Router: E2000 (N-only)
OS: Windows 7 X64
When I'm not connected to my wireless network, the signal strength is 4 bars (out of 5)Once connected, it drops to 2 bars. Speed is 39 Mbps. Why?I have updated the drivers (strangly, it says the drivers are from Ralink Technology. Corp, version 3.00.00.0041 built by: WinDDK)
View 4 Replies
View Related
Jul 26, 2012
I have a E2500 router and just got this AE3000 adapter. Thought that would bump up the wireless signal for using my laptop at the other end of the house about 75 feet from the router. The new E2500 Wireless N has been a big improvement. The AE3000 installed perfectly and shows up as working properly. It's just that the signal strength on my laptop shows 2 bars and the signal strength for the adapter shows 2 bars.
View 2 Replies
View Related
Jun 6, 2012
I have a linksys wrt54g wireless router and a few weeks ago my wireless connection started to become inconsistent, it would randomly drop service or be very slow, and now it has become very inconsistent and slow, all the while the wireless signal would be 4-5 bars.On my windows 7 desktop, often times the yellow triangle with the exclamation mark pops up over the signal strength indicator when its at 4-5 bars.I've tried changing to 2 different routers and its the same, and the problem is persistent for all computers in the house.I've connected directly via ethernet to the modem and router and service was fine.There are a few wireless networks in the area,some with quite strong signals, but I downloaded the xirrus wifi inspector and it says I'm not sharing a channel (channel 1) and though I'm ~15ft from the router, the signal is ~65dbm, which seems low and is almost equivalent to neighbor's wireless strength.
View 2 Replies
View Related
