For some reason my ps3 wont connect,the signal strength is 100% but it just times out.it will randomly connect BUT cant stream anything or connect online.Or it will get disconnected if someone turns on my mine computer in the other room/Should i DMZ the ps3?Routers a WRT610N dual N Firmware Version: 2.00.00 B05 cant upgrade to 3.00 because of "upgrade failed" error.
View 9 RepliesMy wireless router has been spotty since my cable company installed a new modem for cable internet. I have powercycled several times, downloaded new firmware, rebooted and am still having problems. Lately when I do finally get on the internet with a wireless device, the signal strength is very low. It is low on my iphone, on my Mac laptop and also on my Samsung Bluray player. Lately a window keeps popping up when I am trying to watch netflix that states my band width is too low, even though it has been working fine for 2 months. Is my router outdated?
View 5 Replies View RelatedCurrently I'm using one e4200 (v1) as my main router in the house. The wireless coverage downstairs is perfect, but upstairs the signal is weak. To improve this I thought about adding the WAP610N as an access point to my network. But this device gets quite some negative reviews ... Thus I was thinking why not add another e4200 (v2) to my network? The price difference is not that big, especially compared to other simultaneous dual band access points. So my question is, would following scenario work?
- first e4200, connected to my ISP, acting as a router, using both the 2.4 as 5 ghz band (basically my current situation)
- second e4200, connected (via UTP cable) to the first e4200, in bridge mode
- second e4200 also using both 2.4 and 5 ghz band, using the same SSID, security etc but a different channel
So when moving a laptop for example from downstairs to upstairs, automatically the router/access point with the strongest signal would be used.
We have a new e1000 router that was having trouble reaching the TV for Netflix movie streaming. Too many walls and too much distance. A simple solution was to direct the signals from the router by placing aluminum foil behind the router so all the signal was going towards the TV rather than in an 360 degree circle. Now the streaming works great! After the movie is done I remove the foil and everything looks just like it should.
View 9 Replies View RelatedI have a new e3000 series router and on all pc's I'm using model AE1000 receivers. Now, the laptops we use work great until we go out to a room built off the main house (a seasonal porch)
View 2 Replies View RelatedI have configured a new LinkSys e3000 as as wireless router in our house.I have left the configuration as default (only secured it and turned on the DHCP server).I have only turned on the 2,4 GHz network ( because the 5GH had an even shorter range).Everything works and all my devices can connect to the router and access the internet.However i find the signal strenght of the router to be very poor.Already in the next room it drops to 60%. And in some rooms on the 1st floor the signal drops completly.This happens not even 20m away from the router in an ordinary "family house".Is there a setting somewhere which could increase the signal strength ?I noticed that the router has no antenna, can one be bought and attached so the signal increases ?The firmware version is 1.0.02 and i found a newer on your web 1.0.03. How to improve the signal strength?
View 6 Replies View RelatedI have a two story house with a basement. Right now I have a Cisco Linksys E4200 router on the second floor in one of the bedrooms. I have a DLink GamerLouge 4500 in the basement. Both systems have the same SSID and are running on different channels. Computers connect to the appropriate one automatically. At least assuming that's what's happening.I am getting limited connectivity on the first floor in the kitchen and family room. Dining room, right by the second floor stairs is fine. All the bathrooms are dead zones. Note I have thick travertine tiles on the walls in the bathrooms so may inhibit signals. Trying to figure out the optimal solution for getting the house setup so everywhere has at least decent signals. I have alot of iPad and laptop devices floating around the house so wireless is key. Note I have wired plugs with Cat5e all over the house to a central hub in the basement which is where the DLink router sits. Thoughts on how to improve my signal strength? Especially in the farther reaching bedrooms and the first floor
View 4 Replies View RelatedWhat signal strength should I expect when in the same room as the e4200 ?I'm checking signal strength with iStumbler and with option-right click on airport menu icon on my Mac.I'm getting a signal strength of about -55 while in the room with the router.What signal strength should I expect while in the same room, no physical obstructions, etc. ?
View 6 Replies View RelatedI went out and bought a e4200 today and the signal strength is worse than my WGT300n, is there any tweaks I can do to expand my signal strength?
View 3 Replies View RelatedI have a WRT54gh, and the signal strength is extremely poor. Full strength at about 15 centimeters, Then drops to 50% at 50 centimeters. By 1.5 meters, the signal is extremely weak or not visible. Have updated to the latest firmware, factory reset and power cycled. There are no other wireless networks or devices that would provide interference Have experimented with channels, thresholds, transmit type, encrypted/open, intervals etc..No luck. Due to signal dropping off so quickly it seems like a transmit strength issue rather than an issue that can be solved in the menu. I'm wondering if there's a way I can console log-in to the Linux kernel and check the transmit strength and perhaps bump it up by a few DB? It's out of warranty so a solution involving opening the case is also acceptable.
View 9 Replies View RelatedMy WRT400n has started dropping the wireless signal 4 to 5 times a day. Somet times it fixes itself but most of the time I have to re-boot the router to connect a wireless signal.I looked for a firmware upgrade but there hasn't been one since 2009.
View 4 Replies View RelatedI have been disappointed by the range of the EA4500 compared to previous routers, but I am most puzzled by it's behavior. I may get an "excellent" connection close to the router (one room away) and speeds up to 65 Mps, but after a few minutes of surfing the web the signal strength and speed can drop substantially.
The problem is the worst at a distance (one floor down in our house, maybe 30 feet away in total) where the signal strength may start at "good" and a speed of perhaps 30 Mps, but then after 3-4 minutes drops to "poor" and maybe 5 Mps.
Have two WRT54G Wireless Routers.
-One WRT54G ver. 6, Firmware Version v1.028
-One WRT54G ver. 6, Firmware Version v2.x
With the WRT54G ver. 6, Firmware Version v1.028.When I ran the android app WiFi Analyzer, I get mixed results.On my Samsung Galaxy S3, I saw my signal on Channel 2, and others around me (two on Channel 6 and two on Channel 11).On my ASUS Transformer Prime TFT201 I see the same signals, but my router signal bounces continously between the baseline (-100dBm?) and about -35dBm.
Plugged in the WRT54G ver. 2, Firmware Version v2.x Channel 8.Hooked it up and got good steady signal strength. It Had 'WPA - Shared Key' but did not have the 'WPA - Personal' that was on the ver. 6. So, I had to go and screw things up. I've upgraded this to Firmware Version: v4.21.5 and guess what? I now have 'WPA - Personal'. I also have a signal is bouncing on BOTH units.
On my ASUS, I can see both routers. The ver. 2 AND the ver. 6 are bouncing between baseline and -35dBm, in unison. Apprently something in the ASUS does not like the later Firmwares.On my Samsung I can see the two signals - the ver. 2 on Channel 8 is stable as a rock and the ver. 6 on Channel 2 is also bouncing, but at a much slower rate! Running Speedtest.net a PC hardwired to the ver. 2 - I get 5.34 Mb/s Download and 0.47 Mb/s upload (yeah, my Internet sucks!) Running Speedtest.net through the ASUS/WiFi to the ver. 2 - I get 2.43 Mb/s Down and 0.65 Mb/s Up.Running Speedtest.net through the Samsung/WiFi to the ver. 2 - I get 5.07 Mb/s Down and 1.07 Mb/s Up.
I have been using this for over a year with no problems and a couple of days ago, it started disconnecting and reconnecting constantly. I went and updated the firmware for it, but still the same problem.
View 6 Replies View RelatedJust got an E2500 and installed it with no problems and it was working correctly for 1-2 days. This evening the signal strength of my SSID dropped to LOW and a new SSID now shows up with full signal strength. It s not an SSID from any of my neighbors and from checking several forums it appears this is known problem.
View 2 Replies View RelatedI have a linksys router,I reset it and hooked it up,but I don't get internet even though the signal is excellent
View 1 Replies View RelatedI have already seen many threads with the same problem but none of the solutions worked for me.I am unable to connect to my router (Beetel 450TC1) via wireless network. Even if I enter an incorrect security key, no authentication error is displayed. The wired connection works flawlessly and I can access router admin panel through wired connection. Things I have tried:
1) Called up the ISP customer care.They upgraded the router firmware, did a hard reset and did all settings remotely. This did not fix the problem and the executive reported that I have a faulty hardware. I think my hardware is fine because the same problem exists with other smartphone devices and I can connect to college WiFi easily.
2) Changed wireless security authentication and SSID.
3) Tried a manual hard reset and firmware downgrade (same problem persists with downgraded firmware) and again upgrade.
4) Tried different operating systems (Windows 8, Windows 7, Ubuntu 12.04). Same problem exists with each of them.
[code]....
I have a WET610N on my network with very little signal strength. My set up is:
Router E3000
48 ' (48 feet) to
WET610N
The WET610N is on 5Ghz N, and is the only device at Ghz, and indeed the only wireless device during testing.
The use for the adaptor is to connect an Xbox 360 as a MCE for Video streaming.It is unusable, with unwatchable lags and intermittent failures.The 'Network Performance Monitor" doesn't read in mb/s, but essentially I get about 1 or 2 'bars', well under the acceptable for Standard def reading.
zInterestingly, when I bring the device within 3 feet of the router, I get great speeds (30 Mb/s down), but the bit rate reading in the status screen reads lower than the below reading.
Below is at the 45 foot mark->
Link Status:Connected MAC Address:68:7F:74xxxx:31 Network Name (SSID):sx BSSID:98:FC:11:xxxx9:94 Radio Band:5 GHz Channel Width:20 MHz Wide Channel:N/A Standard Channel:36 Bit Rate:43.3Mbps Signal:10% Security:WPA2 Personal
I have a Linksys E1000 router. The macbook is getting great signal even out in the yard. The PC running Windows 7 and using an AE1000 wireless adapter is only getting 2 bars out of 5. I don't think there's any interference. I can't figure out why the signal strength is so poor.
View 5 Replies View RelatedI've noticed something interesting, after having been disconnected from the WLAN in less than 1 minute in my first experience with this Linksys' Modem Router: The signal strength was poor when browsing the Wireless LAN. I was at home, in a room just beside the one where the router was placed at.So, I took a look at connection status, and saw the signal strength was Medium - Weak: something around 30% and 55% You could think it was due to mirrors, the kind of walls between the rooms, and everything else, but I instantly remembered when browsing WLAN from the same place but not with the same router, the signal was strong (100%)...but I let it alone In the other day, while browsing WLAN, I've noticed another thing, this time visible: "TX power" I've got in connection status was 39mW, while I was almost sure it should be 100mW, based on my past WLAN connections Then, today I decided to take a look more deeply in that, and unboxed my Linksys' WRT54G to test. The test was carried on consisting in both Wireless routers placed in the same room, and a solid wall was between me and the routers.I could connect to the two WLANs, but the status of connections were different.
WAG120N:
WRT54G:
As you can see, when connecting to WRT54G , signal reached 100% at some point, whereas in WAG120N , such a mark wasn't possible.Of course, the signal strength was unstable in both routers, but the average level in WRT54G WLAN was greater, being most of time over 90%, and never below 80%.In WAG120N WLAN, average was 82%, and lowest level was 55%.When I went to the room where the routers were at, and right in front of them, no need to say both reached 100%, but as you can see, in WAG120n's case, TX power was still 39mw: I believe it's a firmware fault, once all other routers I've connected to always showed TX power as being 100mW.It shoundn't be related to the general hardware, as Cisco products are high-quality ones.
I have the following problem:
Adapter: WMP600N
Router: E2000 (N-only)
OS: Windows 7 X64
When I'm not connected to my wireless network, the signal strength is 4 bars (out of 5)Once connected, it drops to 2 bars. Speed is 39 Mbps. Why?I have updated the drivers (strangly, it says the drivers are from Ralink Technology. Corp, version 3.00.00.0041 built by: WinDDK)
I have a E2500 router and just got this AE3000 adapter. Thought that would bump up the wireless signal for using my laptop at the other end of the house about 75 feet from the router. The new E2500 Wireless N has been a big improvement. The AE3000 installed perfectly and shows up as working properly. It's just that the signal strength on my laptop shows 2 bars and the signal strength for the adapter shows 2 bars.
View 2 Replies View RelatedAny way to test a wireless router signal strength?
View 2 Replies View RelatedMy router has wireless capability and the signal inside my home is pretty strong so I have no compaints there. The problem comes in when I use my computer which is located in a shed outside. I get a signal maybe 35% of the time, and even then it's weak. I want to use an access point to allow the computer in the shed to aquire internet access. Do I need to hardwire the access point or can I do it wirelessly? Would a repeater be more effective and which config would be best in that case?
View 2 Replies View RelatedI'm trying to increase signal strength on my netgear router for my house.
View 4 Replies View RelatedI have a wireless network in my home, mainly for internet access via any of the 3 or 4 machines we may be using. Normally, there's not a problem with normal surfing, email checking, youtube, etc.My wireless router is a Linksys WRT300N, and the wireless adapter card in my desktop is a D-Link AirPlus G DWL-G510 Wireless PCI Adapter. In my previous home, the router was in the very same room as my desktop, and had no problems to speak of with this setup streaming Netflix. Now, however, I'm set up in an older home, and the router is removed from my desktop by a few walls and tight rooms. I've noticed that my network status icon on the bottom right of my desktop seems to always show "Signal Strength: Very Low".I like to use my desktop sometimes to stream Netflix. My Netflix streaming sometimes goes OK, but typically it just freezes and shows the Loading bar, and sometimes doesn't really start back. It is so bad sometimes, that I am not willing to wait it out, because I know from this experience that even if it starts back up, it will just freeze again. The video is not downloading and caching fast enough.
View 5 Replies View RelatedMy wireless signal strength on my DIR 615 router varies between 57% and 63%. I don't understand why it's not 100%. Is there a way to tweak it up ?
View 2 Replies View RelatedI purchased a WRT610N router early this month, the wireless network was working completely fine when I first set it up. Today I tried to connect my laptop to my wireless network. The laptop isn't able to connect at all. I also got a Sony PSP which has WLAN on and that saying it cannot detect any access point which would be my router.
View 3 Replies View RelatedI have a linksys router WAG 120n and when using wireless if I move into the next room the signal strength goes down to 40% there is only one single wall in between the room and the router. I have upgraded the firmware to the latest version turned off other electrical devices changed the wireless channels but none of this has worked. Any more settings I can try to get the signal stronger, I really don't want to return the router unless completely necessary.
View 4 Replies View RelatedTo connect my new "smart tv" with my wireless linsys WRT610N, smart tv ask to take off all protection such as firewall and antivirus. Doing so, I cannot connect my laptop with my router. Is there a solution to connect both at the same time?
View 1 Replies View RelatedI want to connect one "wrt610n router" to modem directly through Ethernet cable and when i connect both of them every thing is working fine and iit gives proper internet connection through WLAN [code] But, when i tried to connect "second WRT610N router" through "first one WRT610N router" through LAN_cable(cat 5) then second router do'nt provide(give) internet connection second router ip-- 192.168.1.5
View 4 Replies View RelatedI'm trying to use the WET610N as a sort of access point/range extender for a single device, a remote monitoring system installed in a barn. It records temperature, power use, etc, and reports it to the internet. The barn is about 250 feet from the house where the wireless router is installed. There will be very little data flowing over the link.Setup on the WET610N went fine, and it saw the remote router at 10% strength and connected to it fine. However, when I attempt to get Status, the screen shows the headings on the left and no data on the right. Attempting to access the internet through the link on my MacBook Pro failed.
View 6 Replies View RelatedI have metal framing in our house and wireless signal is always a problem is there a way to boost my signal strength?
View 1 Replies View Related