IP Address / Subnet And Gateway Interpretation?
May 15, 2012I have this details 196.14 230.72/ 30. What is the IP, Subnet and gateway from this details
View 1 Replies
ADVERTISEMENT
D-Link DIR-655 :: WAN Gateway Ip Address Must Be Within The WAN Subnet
Aug 5, 2011I am on a University campus and they have provided the following to connect to the internet along with DNS server addresses:
IP Address: 192.168.25.24
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.254.1
When I connect my computer, it gives an error that the IP address and subnet mismatch, but it still connects to the internet just fine. However, if I try to put these settings into the DIR-655 along with my computer's MAC address, it gives me the error "WAN gateway IP address 192.168.25.24 must be within the WAN subnet" and requires I change it.
How To Find IP Address / Subnet Mask And Default Gateway
Apr 18, 2013what my IP address, my subnet mask, and what my default gateway is. I have tried typing "ipconfig" into CMD but then I only got up 100 boxes saying "Permissionisconnected"
View 12 Replies View RelatedLaptop Receives IP Address / Subnet Mask And Gateway - No Internet Access
Sep 28, 2011Have a problem with a laptop connecting to a Wireless Router. The laptop was working fine on the last router which was on an ADSL Network.. (not that that matters),When the new router (Virgin Media / Cable) was installed all other laptops where connecting to it without any probs, but not this one.The laptop in question still receives an IP address, Subnet mask and Gateway from the router - Vista says Local only, no internet access. It cannot ping anything else on the network either. When I do ping it comes back destination host unreachable.
View 6 Replies View RelatedLinksys Wireless Router :: E2000 WAN IP Address Cannot Be Same Subnet As Guest Network IP Address
Jul 16, 2011I switched from Time Capsule with AirPort to E2000 and have a problem with configuration.I use the same IPs as in AirPort and E2000 gives me an error:"The WAN IP address cannot be the same subnet as the Guest Network IP address" and I can't save configuration.But in my opinion they are different.I use "Static IP" option and I have IPs from my ISP: [code] So WAN IP is different subnet as LAN and I don't know what to do now. It worked with these settings in AirPort and here I can't proceed.
View 2 Replies View RelatedCisco Switching/Routing :: Gateway 7600 / How To Know If Bgp Neighbour Advertised Subnet Or Not
Nov 27, 2012how to know if my bgp neighbour advertised my network from his side or not ???
here is my config :
Gateway7600#sh ip bgp
BGP table version is 8, local router ID is 192.168.40.3
Status codes: s suppressed, d damped, h history, * valid, > best, i - internal,
r RIB-failure, S Stale, m multipath, b backup-path, f RT-Filter,
x best-external, a additional-path, c RIB-compressed,
Origin codes: i - IGP, e - EGP, ? - incomplete
RPKI validation codes: V valid, I invalid, N Not found
[code]....
Cisco WAN :: 3945 Router NAT Output Interpretation?
Oct 3, 2012I have some lags on my 3945 router. From show ip nat statistics there is following output:
BR1#show ip nat statistics
Total active translations: 20 (0 static, 20 dynamic; 20 extended)
Peak translations: 8877, occurred 1w0d ago
Outside interfaces:
GigabitEthernet0/0, GigabitEthernet0/1
[code].....
Cisco Switching/Routing :: 3845 Show Version Interpretation
Mar 25, 2012I change only a chasis in a router 3845, but the "show version" command should be the same , except for the serial number and other parameter of time.. however, the number of serial interface change from 4 up to 2.The hardware module of 3845 are 3.
1.- VWIC E1/T1 with 2 port
2.- Fastethernet 36 port
3.- Supervisor engine with 2 Gigabit port
Home Network :: Ip Address In Same Subnet?
Nov 20, 2012i want to give my switch a ip address with same subnet as a pc which is for eg having ip address of class a and subnet of 255.255.240.0
View 4 Replies View RelatedTo Forward To Domain To Subnet Address
Jan 8, 2012How do you forward a domain to a sub-net address? I know how to forward to my network address, but I have not been able to find any documentation on the internet on how to forward to a LAN address.
View 2 Replies View RelatedRouters / Switches :: How To Subnet A Class B IP Address
Jan 16, 2011how to subnet a class B IP address?I have a homework, I don't know how to subnet a class B.
View 2 Replies View RelatedCisco WAN :: 1811 - NAT A Whole Subnet To Secondary Address?
Mar 23, 2012I've got an 1811 router running 15.4 IOS and a cable modem with 5 static IP's attached to Fa0. I would like to dedicate one of those IP's to a dedicated internal subnet (10.0.30.0/24) but I am not sure how to accomplish this?
What would be the best method to accomplish this? Unsure of where to begin..
What Is Correct Subnet Mask And 10th Address Range
Nov 3, 2012Given an IP address range, select the correct subnet mask for the scenario. IP address: 132.250.0.0/16, You need to create 100 networks with a minimum of 500 hosts per network. What is the correct Subnet mask and the 10th subnet address range?
View 1 Replies View RelatedWireless :: Subnet Mask Address Is Illegal Cisco Linksys?
Feb 23, 2011subnet mask address is illegal cisco linksys?
View 1 Replies View RelatedProtocols / Routing :: Partition Departmental IP Network Address Block To Create Staff / Student Subnet?
Sep 28, 2011partition the departmental IP network address block to create a staff and a student subnet. Each of these will be identified by its own network address and netmask. It is university policy that you must be economical with the IP addresses. That is, the subnets must be as small as possible, but they must be large enough to accommodate the maximum number of hosts you were given. Also, it is university policy that the respective gateway router to the outside world should always be given the highest possible host IP address in the subnet. The student subnet should have a higher IP network address than the staff subnet. The network must be able to support up to 60 machines on the staff subnet (not counting the router) and up to 120 machines on the student subnet (also not counting the router).
IP address/netmask
University network address127.158.128.0
University network mask255.255.192.0
University internet gateway IP address127.158.191.254
Department network mask255.255.254.0
Department router address127.158.129.254
Suppose that the network address of the departmental network is 127.158.128.0 (calculated by AND between Dep network mask and Dep router address)I know that 60 machines would use 6 bits for the staff subnet.the netmask of staff would be 255.255.255.192.how can I figure out the the IP network address of the staff subnet.I have worked out the range for the staff subnetwork.
127.158.128.0 - 127.158.128.63
127.158.128.1 = Gateway address
127.158.128.63 = Broadcast address
Now how can I calculate the IP network address of the staff subnet?
Give Gateway Of One As Ip Address Of Another
Feb 28, 2011if i give gateway of one as ip address of another and vice versa? both are directly connected and u cant use hub, switch,router...
View 7 Replies View RelatedISP Blocks Default Gateway Address
Feb 23, 2012My ISP is changing out all the ADSL routers in our area and they have blocked the Default Gateway Address, so we can not access it via Web Browser. This is frustrating because they changed our Wi-Fi password, instead of just keeping what we had like an Einstein. They said they did it because of Hackers
View 2 Replies View RelatedServers :: Default Gateway / IP And DNS Address For Client PC?
May 29, 2012Client is having 1 file server running small business windows server 2003. Server is not configured with domain, it is working only on workgroup. We have around 15 users who are using that server as file server only. Now my main question is do i need to configure DNS server in that server?we also have internet connection running (have problem in that also, will explain next time) with wireless router to connected with switch. So do I need to setup dns in server also or just put static ip (I prefer static then dhcp) & dns server from ip will be ok? If I put dns which I got from ISP, so will it create any problem with using those file from server?the second question is..
What IP address, Default gateway and dns address I should use for Server & also client pc.
router ip - 192.168.1.1
server ip - 192.168.1.10
Currently no DNS setupcurrent configuration - Server
IP - 192.168.1.10
subnet- 255.255.255.0
gateway - 192.168.1.1
dns - 213.42.20.20 (from ISP)
dns2 - xxx.xx.xx.xx (from ISP)current configuration - Client
IP - 192168.1.111(to 115)
subnet - 255.255.255.0
gateway - 192.168.1.1
dns 1 - 192.168.1.10 (File Server)
dns 2 - 213.42.20.20 (from ISP)
Cisco WAN :: Where To Type In Gateway Address In 891 Using CCP Express
Jul 6, 2011We are switching over to a new ISP and the settings from the old ISP Statstic IP,DNS, is on the Cisco 891 router. Question can I just edit the settings that are already on the Cisco 891 router. I clicked on the CCP exress Went to the Task Internet(Wan) Address type is set for Static IP which I can change and the subnet I can change. In the DHCP it is enable DHCP server on the Lan interface VLan1 and I want to keep the Starting IP address and Ending IP address. For the Section DOmain Name Server (DNS) Primary DNS and Secondary DNS I can change it. Where do I type in the Gateway address. I clicked on the Routing and I only see checked Enable dfault Route and checked INterface Fastethernet8. I don't anywhere that I need to type in the Gateway address anywhere in the CCP Express.
View 3 Replies View RelatedWifi Router Not Assigning Ip Address Or Default Gateway?
Oct 25, 2012hrome threw me a DNS lookup failed. I go into my network settings and I noticed that I had limited connectivity. It would switch between no network access and no internet access every few seconds. After a bit of fiddling around, I got it to connect through assigning myself a static IP. This isn't exactly convenient because I use this computer on multiple networks. When I try to have it on automatic IP, I get no IP address or default gateway when I do an ipconfig /all. It would appear that my router quit assigning my laptop an IP for no reason whatsoever. DHCP is enabled on the router, and all other devices work fine. What could possibly be the problem here? I'm 99% sure it's not an IP conflict either. It's not being MAC filtered because I'm on the thing right now posting this through a static IP. It's not my A/V because it's worked great in the past. Perhaps I should also mention it occasionally says "unidentified network" instead of the SSID
View 8 Replies View RelatedPrint In Network Printer With Different Default Gateway Address?
Feb 7, 2012I can't print in my network printer using my Laptop (WIFI). I have check the default gateway of the desktop PC on which connected the printer and its different from my Laptop. Also I cant "SEE" this desktop PC on the LAN.
View 1 Replies View RelatedRouters / Switches :: Default Gateway Ip Address Request Timed Out?
Jul 18, 2011recently, i have connected the internet to my PC with cable. Here the problem is , the packets are not receiving in the status bar of internet connection. I have checked in command prompt, the ip address is connecting properly but the default gateway ip address is showing "Request Timed Out" message.
View 1 Replies View RelatedSpeedtouch Modem Doesn't Provide Gateway Address To Router
Apr 4, 2012My Speedtouch 516v6 modem does'nt provide gateway adress to the TP-Link router. The modem can work in bridged mode or routed mode and I want to use routed mode. TP-Link has PPPoE mode but I would like to use a dynamicIP mode in which the router obtain network parameters from the modem and it does, but it does not obtain a gateway address.
View 2 Replies View RelatedAmilo Pa1510 Connected But Not Surfing (wrong Gateway IP Address)
Mar 30, 2013I have an Amilo Pa1510 (Windows XP) and I can connect to the router but not surfing (browser doesnt load any website). I have tried the commands "ping" to my IP address and it works but ping to the default gateway IP address doesnt work either.I am using the same wireless connection right now with my smartphone. I have downloaded an app that executes the ipconfig command in my Android. I have used the same gateway IP address in my laptop but it didnt work either. I have tried to set automatically the IP addresses in my laptop without success too. I have turned off and on both laptop and router and also checked in the system window that all the processes such as DHCP and DNS servers are automatic and enabled.
View 4 Replies View RelatedCisco Switching/Routing :: Set Management IP Address And Gateway On A 4500?
Apr 24, 2012In mucking around with my 4500 I accidently deleted the ip address that I use to get into it with telnet and CNA. I have a console cable hooked up to and I'm in that way but the commands I got off the internet did not work. Those commands were set interface sc0 10.x.x.x/xx and set interface me1 10.x.x.x/xx. It didn't like interface and I notices when I did a set ?
View 6 Replies View RelatedCisco Firewall :: 3560X Gateway Address For All Of Current Devices
Jul 18, 2011I have an AT&T Router that is my gateway to the internet, I have no access to it. I do have the inside ip address of it which is on my private LAN. Just for shiggles we will call it 10.25.240.1 255.255.248.0. That is my gateway address for all of my current devices.I have this shiny new ASA that I want to throw in there to eliminate a proventia and a sidewinder.
The diagram shows two stacks, these are my virtual server clusters with 3560X switches with the vlans configured, and several more switches all configured with vlan 832, connected to a 2950, which is connected to my internal 2600 router. I have 4 Vlans running on 4 different ip ranges, all controlled by the internal router, with only one vlan, let's say 832 that is trunked to the outside world. That vlan has 172.16.1.x 255.255.0.0 network attached to it. All is well, and traffic is routing behind the internal router, but I cannot seem to figure out how to get the traffic to pass thru the ASA. [code]
Cisco WAN :: DPC3825 Shouldn't Default Gateway IP Have Same Mac Address As Computer / Router
Feb 23, 2013I would like to know what ip addresses I should see in this table. Shouldn't my default gateway IP have the same mac address as my computer or router? There are 2 different ip address/mac addresses from different a ISP than mine. I have a cisco DPC3825..I suspect a someone is spoofing my DNS.
View 4 Replies View RelatedCisco Switching/Routing :: 3500 XL - Remove Default Gateway IP Address
Aug 9, 2012I have a 3500 XL switch with the following default gate IP address that i need to clear from the switch but not quite shore how to remove it.
I've removed the customer original Ip for security reason as this is an open discussion forum and just replaced with 1.1.1.1
switch#show ru
Building configuration...
Current configuration:
!
[Code].....
Cisco Switching/Routing :: 3560 - Servers Updated When Gateway MAC Address Changes?
Feb 7, 2012We have a server connected to a 3560 switch which in turn connects to 6500s. The gateway interface is on the 6500. We will be changing the 6500s so the mac address for the gateway will change, however the IP address will remain the same. As we change out the 6500s the uplink connections to the 3560 will go down. This will flush the old mac address from the 3560.When the 3560 removes a MAC address does it update servers so they have to relearn the correct MAC address?
View 4 Replies View RelatedLinksys Wireless Router :: E1500 DHCP Gateway Address Always Defaults To Access
Apr 28, 2012I have a ADSL Modem with built in router that the E1500 is connected to via Ethernet.If I choose "Automatic Configuration" for the internet connection setting on the E1500 I can enable DHCP on the E1500 but the gateway it gives to clients is always that of itself (192.168.1.1). The gateway it should be is that of the ADSL Modem (192.168. 1. 254).If I choose "Bridge Mode" I can't even enable DHCP.Is there a way I can use the DHCP server?
View 1 Replies View RelatedLinksys Wireless Router :: Connecting WRT300N To Uverse Gateway - Dynamic IP Address?
Feb 6, 2012I have a WRT300n router and want to connect to my Uverse Gateway. When I connect them & try to use the internet connection I get an error that says a connected router must be capable of using DYnamic IP addresses.
View 1 Replies View RelatedLinksys Wireless Router :: Cisco E2500 - Using Gateway Address As Browsing IP For Connected Computers
Jan 31, 2013Everything in our small network worked until today when I had to manually reset the router. We run a application through a provider which requires that we view it from the same IP address for access. We have a statis IP assigned by our ISP solely for this purpose. For simplicity, lets us 23.11.23.176 as the statis assigned by our ISP and 23.11.23.175 as the gateway also assigned by our ISP. The application we need to browse requires that we use the 23.11.23.175 address else it is blocked from viewing. When we hard line into the modem, we are able to browse it fine. When I connect the CISCO router and do it wirelessly, it shows our address as 23.11.23.176 what are the required steps in order to set the CISCO router to use the Gateway address as the browsing IP for computers connected to it. We had set it up about a year ago, and i completely forgot how.
View 2 Replies View RelatedAdding A Subnet To A Switch On Different Subnet?
Aug 3, 2012What I am trying to do is I have one switch with say a 10.1.9.1 sub-net I need to have one of the ports to be trucked with two vlans one for DSL and the other for a local connection with the sub-net of 10.1.5.1 both of the sub-nets are configured in the core as 9 and 5 so I have port 0 set up as a trunk and it is set up as ge-0/0/0.0 vlan_5, vlan_192 on the 10.1.9.1 subnet switch. The DSL is working but the local is not pulling a 10.1.5.1 IP and has no connectivity. Everything looks as if it is configured correctly but still the DSl is working but not the Local connection.
View 2 Replies View Related