I have a WRT300n router and want to connect to my Uverse Gateway. When I connect them & try to use the internet connection I get an error that says a connected router must be capable of using DYnamic IP addresses.
View 1 RepliesSo we just had Att Uverse installed in our apartment and the 2wire box has not been too reliable. I was trying to set up my Linksys router to provide an additional wireless network but i was having some problems with the set-up
View 3 Replies View RelatedJust got WRT300N for connecting my ps3 thru wi-fi. I got everything works but the signal that I got from my PS3 is around 50% only. I am using latest Linksys firmware. My ps3 is located around 25 feet away one floor down from my wireless router. But there is no major wall inbeween the connection. My WRT300N should be a cutting edge product for networking. How come I still got 50% signal strength? Besides moving the router or pS3 closed to each other.
View 5 Replies View RelatedI have a high speed wireless DSL router from my ISP (Telus). I use one port off the router to connect directly to my desktop computer. Another port is connected to a switch to which ethernet cables to three other rooms are connected. My problem is that when I connect my Bell PVR (9242) to the 'switched' ethernet cable, I'm apparently not able to get a dynamic ip address, which the Bell unit requires, and can't connect to the network.can I connect another router, in place of the switch, to deliver dynamic IP addresses to whatever I connect to the ports in the other rooms in my house?
View 2 Replies View RelatedI have a compaq laptop running Vista. We recently had our Uverse wireless router/modem replaced. Now my laptop will not connect to the internet. The laptop connects to the router but shows up as local connection only. Uverse tried all kinds of differant things to no avail. The laptop will hookup with a USB modem but I would like to get it back to how it was before.
View 14 Replies View RelatedI recently swapped out an RV082 with a newer model (still RV082 but black and a different interface). I configured the Gateway to Gateway VPN exactly as it was before but none of the three other RV082's will connect. I have tried deleting the connections several times to no avail. I have aggressive mode disabled and have tried with the firewall on and off. Below are the settings (IP's have been X'd out) and the log.
Settings:
IP OnlyIP Address : X0X.X0X.20.31Local Security Group Type : IPSubnetIP RangeIP Address : Subnet Mask : Remote Group Setup
Remote Security Gateway Type : IP OnlyIP AddressIP by DNS Resolved : Remote Security Group Type : IPSubnetIP RangeIP Address : Subnet Mask : AES-192AES-256AES-128 AES-192AES-256 AES-128 IPSec Setup3DES Keying Mode : ManualIKE with Preshared keyPhase 1 DH Group : Group 1 - 768 bitGroup 2 - 1024 bitGroup 5 - 1536 bitPhase 1 Encryption : DES Phase 1 Authentication : MD5SHA1Phase 1 SA Life Time : secondsPerfect Forward Secrecy : Phase 2 DH Group : Group 1 - 768 bitGroup 2 - 1024 bitGroup 5 - 1536 bitPhase 2 Encryption : NULLDES3DES Phase 2 Authentication : NULLMD5SHA1Phase 2 SA Life Time : secondsPreshared Key : Minimum Preshared Key Complexity : EnableLOG:
[code].....
My wifi router is linksys WRT300N v1.1 At first my wifi works great with this devices . iphone 4s , ipod touch 4 , hp pavilion dv6 , dell inspirion 1545 . But it don't works with android devices I had a bunch of them samsung galaxy s3 , galaxy nexus , amazon kindle and more ...The android devices connect to wifi but wifi doesn't work for them in browsers I can't open pages there's appears <webpage not available> , but I can use skype on android devices.
View 1 Replies View Relatedconnecting a VPN with a dynamic IP address (its a Draytek 2700)We have a customer who has a PIX515E on the central site .Than there are more 2 sites where he installed 2 Draytek 2700 ,and contracted 2 fixes IP addresses for them.These are working fine and always did.In another site they are doing building renewals ,só they will not have ADSL for about 2 month,and they connected a 3G Internet access wich is connected to a Draytek 2710 ,internet wich is working fine,but doesnt have a fixed ip address.
I had search a lot in Cisco support pages,but i can´t find this solution,cause the examples are only to 1 dynamic peer ,not mixed(multiple fixed ip addresses + 1 or more dynamic)The PIX also needs to receive VPN connections from remote users who connect via Cisco VPN client(is working fine too) [code] I know now that when a communication starts from that dynamic peer to the PIX ,PIX doesnt know in wich group he should assign it.So the communication stops.i tried to create a group-policy...but i dont know how to associate it with the tunnel group.I also know that we can just associate 1 crypto map to each interface.
I have a ADSL Modem with built in router that the E1500 is connected to via Ethernet.If I choose "Automatic Configuration" for the internet connection setting on the E1500 I can enable DHCP on the E1500 but the gateway it gives to clients is always that of itself (192.168.1.1). The gateway it should be is that of the ADSL Modem (192.168. 1. 254).If I choose "Bridge Mode" I can't even enable DHCP.Is there a way I can use the DHCP server?
View 1 Replies View RelatedEverything in our small network worked until today when I had to manually reset the router. We run a application through a provider which requires that we view it from the same IP address for access. We have a statis IP assigned by our ISP solely for this purpose. For simplicity, lets us 23.11.23.176 as the statis assigned by our ISP and 23.11.23.175 as the gateway also assigned by our ISP. The application we need to browse requires that we use the 23.11.23.175 address else it is blocked from viewing. When we hard line into the modem, we are able to browse it fine. When I connect the CISCO router and do it wirelessly, it shows our address as 23.11.23.176 what are the required steps in order to set the CISCO router to use the Gateway address as the browsing IP for computers connected to it. We had set it up about a year ago, and i completely forgot how.
View 2 Replies View RelatedI am using my wireless adapter..a Linksys AE1000..to connect to a friend's ATT U-Verse high speed internet for a few weeks. Due to a petty argument with his girlfriend..I overheard her and her friend and discovered that she had logged into the Uverse router/modem (192.168.1.254), which shows all devices that are connected. On this page it has links to access files for each device. Clicking on that, she was able to read all my files. Nothing to hide, I just don't like snoopers and even wonder if she could change settings or do something to mess up my computer. I cannot figure out how to block access by her Uverse thru my Linksys wireless adapter.
I normally do not allow any sort of file sharing and everywhere I have looked on my PC, nothing is enabled to file share or remote desktop share or anything like that. I'm not a total noob but have no clue if and how I can change this on my end so that she cannot get into my PC while I'm connected to their internet. Their router/modem is a 3800HGV-B.
After enduring some protracted problems with wireless connectivity, I decided to bite the bullet and upgrade my Linksys WRT300N from firmware version 2.00.08 to 2.00.21.I found the links to advice on how to achieve this, via a two-stage upgrade url...I followed the following steps: Upgrade firmware using file "wrt300n.bin" file, as per the above link. This brought the firmware version to 2.00.17. Upgrade went smoothly - config page refreshed after rebooting the router and all was well.Upgrade firmware using file "WRT300N-EU-ETSI-ML-2.00.21-code.img" file, downloaded from the Linksys support site. Again, the upgrade went smoothly (apparently) ... except that after rebooting the router, my config page failed to refresh.I have since powered the router off (wait 30 seconds) and on again. Still no web access.
The device, however, does seem to be working OK. I have wireless access, and wireless access, via computers on my network. The only thing I cannot do is access the web config page - but that's not quite satisfactory. I have a number of customised settings on the device, saved to a config file. Included among those is a changed IP address for the router of 192.168.1.10. I am tempted to do a hard reset to factory defaults, connect via a dedicated cable connection and then reapply my custom settings (either manually, or from the config file.) However at this stage I have no confidence that the device will have web access after reset - and then it won't be working for me at all!
Does firmware version 2.00.21 require http access via a specific port (i.e. not 80)? Is there some other way I can access the device for modifying configuration, other than by the web utility? (I have posted another question about obtaining a copy of my long-ago-misplaced Setup CD-ROM.
I unplugged my router and when I plugged it back in, it stopped working. The 4 port lights and the ethernet light come on immediately when I plug it in instead of the normal boot sequence.
I tried resetting it, leaving it unplugged for long periods, using the power supply from my other router,... nothing works.
I've got a WRT54G v6 that is password protected via WPA2 Personal TKIP+AES, and SSID broadcast enabled. In the Status menu > Local Netork > DHCP Clients Table there is a MAC Address listed that none of my devices have.
View 6 Replies View RelatedI have WRT300N V1.0 with Firmware v1.03.6.what is latest Firmware for WRT300N V1.0 and where I can get it.I tried at Downloads under Support in Cisco website but it said "No firmware/driver download available".
View 1 Replies View Relatedi looked everwhere for the firmware. cant find it anywhere. looking for 1.0 or 1.1 firmware for wrt300n.
View 4 Replies View RelatedPS Linksis Online Support said they do not have old firmware andgives me some phones to call .. Others have written about the same problem, saying that prior toupgrade with new firmware to be flash with 2.0.14.I need firmware - version: 2.0.14, where to find it?
View 9 Replies View RelatedI need to be able to setup to 5 external ip addresses. I was told to do this you need one to one NAT. I don't know if my router has this or not and if not is it possible to upgrade the firmware for this feature? the router I have is a linksys WRT300N V1.1 firmware : Firmware Version: v1.51.2
View 1 Replies View RelatedIn my home I have a cable modem wired to a links wireless router a wrt 300n in my office (only hardwired used in there) and I do not get such good distance to my back bedrooms with my laptop. I have run a Ethernet cable dead center of the house for my sat receiver that is connected and wired to the 300wrt. Here is my question can I use the 150 like a hub or switch at the office connected to the cable modem and use the wrt300n router so that I get wireless on that side of the house. Or in reading here I see I can maybe use a bridge. I do have a older Linksys wrt150n sitting in a box.I have read until my eyes are almost bleeding and am not sure. How I can get a better signal on the other side of the house.
View 4 Replies View RelatedI connected a switch and the device is not even recognized in my router site.
View 12 Replies View RelatedUnable to connect to internet via laptop + desktop to wireless Linksys router. Model=WRT300N.
Connection worked fine on my laptop before, however, stopped working approx 3 days ago.In attempt to resolve connection issue, I de-install linksys software from my desktop, now I cannot execute setup due to the fact that I cannot connect to the internet.
Since the secondary router WRT300N uses the same default IP 192.168.1.1 as the primary installed router EA4500, any attempt to log onto the set up page results in diversion to the Cisco Connect Cloud for the primary router.
Is there a way to access the set up page for the secondary WRT300N, bypassing the main router intervention via the Cloud software?
I've had this WRT300N for several years and it has worked very well.It suddenly dropped all wireless connections and no one can re-connect. My main pc is hard wired directly to the router and works perfectly as always. 3 wireless pc's and 3 handheld devices suddenly can't connect. I've powered down my modem and router for several minutes, but nothing changed. The firmware was upgraded a long time ago and there are no other upgrades available.
View 7 Replies View RelatedFor reasons I will explain in a separate thread, following a firmware upgrade to version 2.00.21, I am no longer able to connect to my WRT300N using the web interface. The device seems to be working fine (but for the lack of the web config access.) I'm loathe to leave it "inaccessible" and would like to use the Setup CD-ROM described in the manuals to connect directly to the device to see if I can fix the problem.
I have been through my "filing system" (read "junk room") to try to find the original device packaging, wherein I am sure I would find the original CD-ROM. Is there anywhere I can download an image of the original Linksys Setup CD-ROM for the WRT300N version 2.0 device?
So lately my internet has been painstakingly slow, Youtube videos dont load, Web Pages take FOREVER, its killing me. So I ran some speed tests This is wireless over my router. (WRT300N (Yes i know its old))
And this is direct connetion from my modem this really just makes me want to never use the internet again.
Due to problems with my wifi connection, I had to reset my router and modem. I have to reinstall my settings now, and therefore I need to write down a security number. That should be written on the back of my router (model WRT300N), a barcode with 8 numbers. I can't find that code. Where can I find it or is there another way to reinstall my connection and put a password on it? It's open access now.
View 2 Replies View RelatedI have a WRT300N wireless router that was working fine until I tried hooking up an Air ave Access Point for Sprint. Now the router doesn't work at all - even the hard wired connections don't work. I tried the usual - unplugging, plugging back in, disconnecting, reconnecting, hitting the reset button - nada.
Removing the Air ave Access Point doesn't matter - it still doesn't work when I put it back the way I had it before. The only way I can get a signal to my computer is to plug it directly into the modem, bypassing the router.
Why I can't play online on xbox live. I'm set on going online but when I go on to play online for MW3(Modern Warfare 3) my NAT Type says strict,I can't join any of my friends games. It says to go on infintyward.com/Nat and when I do it doesn't show my model of linksys (WRT300N) i reset my xbox,my router and still nothing
View 3 Replies View RelatedI cannot seem to figure out how to connect my Canon MP620 Wireless printer to my wireless router. The router is a WRT300N v 1.1 with the latest firmware upgrade. I am using WPA for security. I can connect to the printer wirelessly through my neighbor's open system so it has something to do with security I suspect. I have enabled the AP feature and disabled it to see if that is an issue. That has not changed anything. I have looked at other posts with HP printer issues and access point posts but none of those solutions have worked. The Canon gives me an option to use the WPA, WPA2 and WEP?
View 3 Replies View RelatedCan a Linksys WRT300N wireless router be used as an LWAPP AP device?
View 1 Replies View RelatedI have installed a WRT300N on to a new machine and the connection speed reads as 1 Mbps (not 100 but 1 ). I did a ping test and the results are
View 2 Replies View RelatedHere is where I want to go:
Windows server 2008 (providing DHCP and DNS) 192.168.89.1 on all
Cisco SG 300-20 (switch) 192.168.89.3
all Clients(15 x DHCP assigned IPs) connected to switch
WRT300N(192.168.89.2) connected to switch
Internet modem connected to WRT300N
To achieve this I need to disable DHCP on the WRT300N, since my server is providing DHCP.The issue I have is that when I disable DHCP at the WRT300N, I lose internet connection (connected to either switch or direclty to WRT300N).
If I conact from the modem to the pc I have internet so it must be the router. The power light is blinking along with all the port lights. Power light is blinking one time slow 2 fast. Have tried holding the reset button for 30 seconds and unpluging for 30 seconds. Can not go to the ip address it times out. New firmware is not avalible.
View 9 Replies View Related