Linksys Wireless Router :: WRT300N - Air Ave Access Point For Sprint
Mar 8, 2012
I have a WRT300N wireless router that was working fine until I tried hooking up an Air ave Access Point for Sprint. Now the router doesn't work at all - even the hard wired connections don't work. I tried the usual - unplugging, plugging back in, disconnecting, reconnecting, hitting the reset button - nada.
Removing the Air ave Access Point doesn't matter - it still doesn't work when I put it back the way I had it before. The only way I can get a signal to my computer is to plug it directly into the modem, bypassing the router.
View 1 Replies
ADVERTISEMENT
Nov 28, 2011
Can a Linksys WRT300N wireless router be used as an LWAPP AP device?
View 1 Replies
View Related
Sep 16, 2011
After enduring some protracted problems with wireless connectivity, I decided to bite the bullet and upgrade my Linksys WRT300N from firmware version 2.00.08 to 2.00.21.I found the links to advice on how to achieve this, via a two-stage upgrade url...I followed the following steps: Upgrade firmware using file "wrt300n.bin" file, as per the above link. This brought the firmware version to 2.00.17. Upgrade went smoothly - config page refreshed after rebooting the router and all was well.Upgrade firmware using file "WRT300N-EU-ETSI-ML-2.00.21-code.img" file, downloaded from the Linksys support site. Again, the upgrade went smoothly (apparently) ... except that after rebooting the router, my config page failed to refresh.I have since powered the router off (wait 30 seconds) and on again. Still no web access.
The device, however, does seem to be working OK. I have wireless access, and wireless access, via computers on my network. The only thing I cannot do is access the web config page - but that's not quite satisfactory. I have a number of customised settings on the device, saved to a config file. Included among those is a changed IP address for the router of 192.168.1.10. I am tempted to do a hard reset to factory defaults, connect via a dedicated cable connection and then reapply my custom settings (either manually, or from the config file.) However at this stage I have no confidence that the device will have web access after reset - and then it won't be working for me at all!
Does firmware version 2.00.21 require http access via a specific port (i.e. not 80)? Is there some other way I can access the device for modifying configuration, other than by the web utility? (I have posted another question about obtaining a copy of my long-ago-misplaced Setup CD-ROM.
View 4 Replies
View Related
Aug 13, 2012
Since the secondary router WRT300N uses the same default IP 192.168.1.1 as the primary installed router EA4500, any attempt to log onto the set up page results in diversion to the Cisco Connect Cloud for the primary router.
Is there a way to access the set up page for the secondary WRT300N, bypassing the main router intervention via the Cloud software?
View 3 Replies
View Related
Aug 20, 2012
I unplugged my router and when I plugged it back in, it stopped working. The 4 port lights and the ethernet light come on immediately when I plug it in instead of the normal boot sequence.
I tried resetting it, leaving it unplugged for long periods, using the power supply from my other router,... nothing works.
View 6 Replies
View Related
Aug 8, 2007
Just got WRT300N for connecting my ps3 thru wi-fi. I got everything works but the signal that I got from my PS3 is around 50% only. I am using latest Linksys firmware. My ps3 is located around 25 feet away one floor down from my wireless router. But there is no major wall inbeween the connection. My WRT300N should be a cutting edge product for networking. How come I still got 50% signal strength? Besides moving the router or pS3 closed to each other.
View 5 Replies
View Related
Apr 25, 2012
I have WRT300N V1.0 with Firmware v1.03.6.what is latest Firmware for WRT300N V1.0 and where I can get it.I tried at Downloads under Support in Cisco website but it said "No firmware/driver download available".
View 1 Replies
View Related
May 16, 2012
i looked everwhere for the firmware. cant find it anywhere. looking for 1.0 or 1.1 firmware for wrt300n.
View 4 Replies
View Related
Jun 16, 2011
PS Linksis Online Support said they do not have old firmware andgives me some phones to call .. Others have written about the same problem, saying that prior toupgrade with new firmware to be flash with 2.0.14.I need firmware - version: 2.0.14, where to find it?
View 9 Replies
View Related
Feb 8, 2013
I need to be able to setup to 5 external ip addresses. I was told to do this you need one to one NAT. I don't know if my router has this or not and if not is it possible to upgrade the firmware for this feature? the router I have is a linksys WRT300N V1.1 firmware : Firmware Version: v1.51.2
View 1 Replies
View Related
Aug 6, 2011
In my home I have a cable modem wired to a links wireless router a wrt 300n in my office (only hardwired used in there) and I do not get such good distance to my back bedrooms with my laptop. I have run a Ethernet cable dead center of the house for my sat receiver that is connected and wired to the 300wrt. Here is my question can I use the 150 like a hub or switch at the office connected to the cable modem and use the wrt300n router so that I get wireless on that side of the house. Or in reading here I see I can maybe use a bridge. I do have a older Linksys wrt150n sitting in a box.I have read until my eyes are almost bleeding and am not sure. How I can get a better signal on the other side of the house.
View 4 Replies
View Related
Apr 2, 2010
Unable to connect to internet via laptop + desktop to wireless Linksys router. Model=WRT300N.
Connection worked fine on my laptop before, however, stopped working approx 3 days ago.In attempt to resolve connection issue, I de-install linksys software from my desktop, now I cannot execute setup due to the fact that I cannot connect to the internet.
View 9 Replies
View Related
Jul 4, 2011
I've had this WRT300N for several years and it has worked very well.It suddenly dropped all wireless connections and no one can re-connect. My main pc is hard wired directly to the router and works perfectly as always. 3 wireless pc's and 3 handheld devices suddenly can't connect. I've powered down my modem and router for several minutes, but nothing changed. The firmware was upgraded a long time ago and there are no other upgrades available.
View 7 Replies
View Related
Sep 16, 2011
For reasons I will explain in a separate thread, following a firmware upgrade to version 2.00.21, I am no longer able to connect to my WRT300N using the web interface. The device seems to be working fine (but for the lack of the web config access.) I'm loathe to leave it "inaccessible" and would like to use the Setup CD-ROM described in the manuals to connect directly to the device to see if I can fix the problem.
I have been through my "filing system" (read "junk room") to try to find the original device packaging, wherein I am sure I would find the original CD-ROM. Is there anywhere I can download an image of the original Linksys Setup CD-ROM for the WRT300N version 2.0 device?
View 7 Replies
View Related
Jan 22, 2013
So lately my internet has been painstakingly slow, Youtube videos dont load, Web Pages take FOREVER, its killing me. So I ran some speed tests This is wireless over my router. (WRT300N (Yes i know its old))
And this is direct connetion from my modem this really just makes me want to never use the internet again.
View 9 Replies
View Related
Jan 2, 2013
Due to problems with my wifi connection, I had to reset my router and modem. I have to reinstall my settings now, and therefore I need to write down a security number. That should be written on the back of my router (model WRT300N), a barcode with 8 numbers. I can't find that code. Where can I find it or is there another way to reinstall my connection and put a password on it? It's open access now.
View 2 Replies
View Related
Jan 15, 2012
Why I can't play online on xbox live. I'm set on going online but when I go on to play online for MW3(Modern Warfare 3) my NAT Type says strict,I can't join any of my friends games. It says to go on infintyward.com/Nat and when I do it doesn't show my model of linksys (WRT300N) i reset my xbox,my router and still nothing
View 3 Replies
View Related
Oct 10, 2009
I cannot seem to figure out how to connect my Canon MP620 Wireless printer to my wireless router. The router is a WRT300N v 1.1 with the latest firmware upgrade. I am using WPA for security. I can connect to the printer wirelessly through my neighbor's open system so it has something to do with security I suspect. I have enabled the AP feature and disabled it to see if that is an issue. That has not changed anything. I have looked at other posts with HP printer issues and access point posts but none of those solutions have worked. The Canon gives me an option to use the WPA, WPA2 and WEP?
View 3 Replies
View Related
Aug 18, 2007
I have installed a WRT300N on to a new machine and the connection speed reads as 1 Mbps (not 100 but 1 ). I did a ping test and the results are
View 2 Replies
View Related
Apr 5, 2012
Here is where I want to go:
Windows server 2008 (providing DHCP and DNS) 192.168.89.1 on all
Cisco SG 300-20 (switch) 192.168.89.3
all Clients(15 x DHCP assigned IPs) connected to switch
WRT300N(192.168.89.2) connected to switch
Internet modem connected to WRT300N
To achieve this I need to disable DHCP on the WRT300N, since my server is providing DHCP.The issue I have is that when I disable DHCP at the WRT300N, I lose internet connection (connected to either switch or direclty to WRT300N).
View 6 Replies
View Related
Aug 15, 2011
If I conact from the modem to the pc I have internet so it must be the router. The power light is blinking along with all the port lights. Power light is blinking one time slow 2 fast. Have tried holding the reset button for 30 seconds and unpluging for 30 seconds. Can not go to the ip address it times out. New firmware is not avalible.
View 9 Replies
View Related
Feb 6, 2012
I have a WRT300n router and want to connect to my Uverse Gateway. When I connect them & try to use the internet connection I get an error that says a connected router must be capable of using DYnamic IP addresses.
View 1 Replies
View Related
Nov 20, 2011
I have a WRT300N and the power light is dim and all 4 ports are solid green along with the internet light being solid green.. Nothing else is plugged in.. Just the power.. I have tried to hard reset and nothing happens.
View 2 Replies
View Related
Feb 24, 2012
Comcast service went down in our neighborhood and when it came back up my internet was down and all five LED lights on my Linksys router are solid green. Tech support tells me that I have to reset the unit to get it to function again.It's been a very long time since I set up the home network and while I'm pretty sure I can make my way through setting up from scratch (I'm assuming resetting goes back to factory settings) I was hoping there was a way to reconnect the router to the modem while retaining all the current security and settings.
View 2 Replies
View Related
Mar 29, 2012
I've just managed to reset the WRT 300N to default settings and have setup the internet connection etc and home network ... BUT no matter how I've fiddled with the wireless settings I cannot get any of the laptops or mobile phones to connect wireless to the network.The Windows software on the laptops 'finds' the router OK but for some reason the router seems unwilling to supply an IP address.I've checked ALL of the settings that I can think of, and all are correct ... well, all are exactly the same as my old router which worked perfectly.
View 4 Replies
View Related
Nov 28, 2011
Whether the Linksys WRT300N wireless routers are compatible with LWAPP configuration?My school lab setup uses Cisco integrated services routers with NM-AIR-WLC6-K9 network modules as controllers in the LWAP network. The controller accepts configuration without error but does not pick up or seem to see the WRT300 AP routers, so cannot push out basic LWAP config info
View 1 Replies
View Related
Jan 18, 2011
How do I configure my Linksys N Router for a Netgear Wireless N Access Point set in repeater mode? Linksys and Netgear are communicating, but no Internet access is available on Netgear which makes me think I need to configure Linksys to provide Internet connectivity to the Netgear access point repeater.
View 1 Replies
View Related
Jun 19, 2011
How to install linksys wireless router to access point?
View 1 Replies
View Related
Aug 14, 2011
Can I use a second linksys wireless router as an access point and can I connect a wired computer to one of its ports?
View 1 Replies
View Related
Mar 22, 2013
I have a FIOS setup with their Router/modem providing DHCP and Wireless routing. The problem I have is that I have a mix of older equipment and newer equipment. The newer equipment is capable of supporting WPA2, the older is not. I would like the benefits of WPA2, but still would like to at times be able to use the older equipment.My solution was to use a WRT160N v2 router that I had as an access point and it also gives me switch capabilities for wired systems as the FIOS router in on a different floor than the Linksys router. Wired access works just fine and the wireless worked fine until just recently.Since both routers have the same default IP addresses I changed the Linksys to a different static IP and turned off DHCP. I left all of the other defaults the same. I set up the Linksys for WEP and created the key for security. Everything worked fine for the better part of a year, but recently I am having problems where some of the computers cannot find the network or find it then lose connection.
View 9 Replies
View Related
Feb 2, 2011
I'm currently using my WRT320N router as an access point (connected to another linksys router), but I've lost my username and password to access the web-based utility. So I need to press the reset button and set it up again. Currently everything is working fine, but I've forgotten how to configure the router for this purpose, and I can't find instructions in the user's guide online. I seem to remember it being troublesome. I know I have to assign a different IP address (currently I'm using 192.168.1.113.) What other settings (if any) need to be changed?
View 2 Replies
View Related
Feb 24, 2013
"Can I get my E2100L to receive a wireless signal from a different model Wireless Router and repeat it via wireless and Ethernet. Yes or NO?"
- If so, how, if u need to user guide here: E2100L User Guide
View 4 Replies
View Related
Dec 11, 2011
I am using a newer wireless router but would like to use my older wrt54g router as an access point (wired and wireless) at the other end of my house. how to do it, and what the specific settings should be, especially the security settings. I can connect the wrt54g via a homeplug (cannot run a LAN cable). I had previously tried an Aztech wireless homeplug but found the security feature to be worthless and everyone was able to "break-in".
View 3 Replies
View Related