Linksys Wireless Router :: WRT300N Dropped Connection Completely

Jul 4, 2011

I've had this WRT300N for several years and it has worked very well.It suddenly dropped all wireless connections and no one can re-connect.  My main pc is hard wired directly to the router and works perfectly as always.  3 wireless pc's and 3 handheld devices suddenly can't connect. I've powered down my modem and router for several minutes, but nothing changed.  The firmware was upgraded a long time ago and there are no other upgrades available.

View 7 Replies


ADVERTISEMENT

Linksys Wireless Router :: WRT300N - No Internet Connection Via Laptop

Apr 2, 2010

Unable to connect to internet via laptop + desktop to wireless Linksys router. Model=WRT300N.
 
Connection worked fine on my laptop before, however, stopped working approx 3 days ago.In attempt to resolve connection issue, I de-install linksys software from my desktop, now I cannot execute setup due to the fact that I cannot connect to the internet.

View 9 Replies View Related

Linksys Wireless Router :: WRT300N Way To Reinstall Connection And Put Password

Jan 2, 2013

Due to problems with my wifi connection, I had to reset my router and modem. I have to reinstall my settings now, and therefore I need to write down a security number. That should be written on the back of my router (model WRT300N), a barcode with 8 numbers. I can't find that code. Where can I find it or is there another way to reinstall my connection and put a password on it? It's open access now.

View 2 Replies View Related

Linksys Wireless Router :: Reset WRT300N To Default Settings To Setup Internet Connection

Mar 29, 2012

I've just managed to reset the WRT 300N to default settings and have setup the internet connection etc and home network ... BUT no matter how I've fiddled with the wireless settings I cannot get any of the laptops or mobile phones to connect wireless to the network.The Windows software on the laptops 'finds' the router OK but for some reason the router seems unwilling to supply an IP address.I've checked ALL of the settings that I can think of, and all are correct ... well, all are exactly the same as my old router which worked perfectly.

View 4 Replies View Related

Linksys Wireless Router :: WRT54G Signal Vanishes Completely / Keeps Dropping Connection?

Dec 26, 2012

My old WRT54G V8 router has been acting up lately. It keep dropping the connection out of the blue. Sometimes I'd be browsing the Internet when the router's signal vanishes completely, it disappears from the list of available wireless networks on not just my computer, but my smartphone and all other devices in the household! Other times I keep connected to the network but there's no access to the Internet. Everything seems fine on the ISP's part, I can connect just fine directly from my modem, so I'm certain the problem is with the router. Besides, these problems are solved by just power cycling the router.

View 4 Replies View Related

Linksys Wireless Router :: WRT54GS - Reset Security Button Completely Shut Out Connection

Oct 3, 2011

I was in the Wireless tab>Basic Wireless Settings and then I clicked the "Reset Security" button.  I don't know what that did but I've been completely shut out of my connection ever since and I don't know how to fix it. I tried doing the install sequence of the router just now (Clone MAC address, then release and renew DHCP, power cycle modem, router, and PC) but it still didn't work.

View 1 Replies View Related

Linksys Wireless Router :: Intermittent Dropped Connection With E4200

May 25, 2012

Bought an E4200 to replace my Netwgear router and am experiencing the following problem.One of my wireless boxes serves as mu mail server. I've been running this configuration for years so the only thing that has changed is the router.The neworkd is up and all wireless clients can connect, but after some time, access to the mail server just 'freezes'. I say freezes as the nework icon (i'm using ubuntu' still show a connection. In addtion, there are not error in any of the logs. I just seems that the mail server and the router just stopped communication.

View 9 Replies View Related

Linksys Wireless Router :: E2500 - Connection Dropped On Both G And N Cards

Feb 18, 2012

I recently purchased a linksys E2500 for my home network. Occassionally, we have dropped connections, on both G and N cards.The router is connected to a corei3-2100 cpu with 6 gb ram and a 1tb hd, running win7 64bit. Ive bought home plugs for my wife's computer(in the house)and.an outdoor wireless antenna (a CCRANE super usb wifi antenna)  for my computer in the garage. I still get dropped signals in the garage, which is only about 50 ft from the router. My computer in the garage is an AMD dualcore 4400 with 4 gb ram, and multiple hdds.What else can  I do to get a better and more constant connection.

View 1 Replies View Related

Linksys Wireless Router :: E4200 Connection Dropped Once Homeplug Connected

Jan 3, 2012

I just installed a E4200, and found that once I connected my Homeplug Powerline to E4200, the connected (wired / wireless) computer (with E4200) connection will be dropped.  The connection become normal again once I disconnected the Homeplug with E4200.

View 5 Replies View Related

Linksys Wireless Router :: E4200 Connection Speed Dropped From 2megs / Sec To 100k / Sec

Jul 1, 2011

I got several issues with the E4200.First of all, my connection speed dropped from 2megs/sec to 100k/sec with that router. Flashing it with the lastest firmware worked but still, I don't get all my speed as I has with my WPG54GS (with DD-WRT).Second, speed is really unstable, like if it was working by burst of data.Third, I got a gigabit port on my computer, plugged in the router and still, I can't make more than 10megs/sec WIRED (!) between my computers. I desactivate the ipv6 from my network card but still, no luck.

View 5 Replies View Related

Linksys Wireless Router :: WRT300N No Web Access

Sep 16, 2011

After enduring some protracted problems with wireless connectivity, I decided to bite the bullet and upgrade my Linksys WRT300N from firmware version 2.00.08 to 2.00.21.I found the links to advice on how to achieve this, via a two-stage upgrade url...I followed the following steps: Upgrade firmware using file "wrt300n.bin" file, as per the above link.  This brought the firmware version to 2.00.17.  Upgrade went smoothly - config page refreshed after rebooting the router and all was well.Upgrade firmware using file "WRT300N-EU-ETSI-ML-2.00.21-code.img" file, downloaded from the Linksys support site.  Again, the upgrade went smoothly (apparently) ... except that after rebooting the router, my config page failed to refresh.I have since powered the router off (wait 30 seconds) and on again.  Still no web access.
 
The device, however, does seem to be working OK.  I have wireless access, and wireless access, via computers on my network.  The only thing I cannot do is access the web config page - but that's not quite satisfactory.  I have a number of customised settings on the device, saved to a config file.  Included among those is a changed IP address for the router of 192.168.1.10.  I am tempted to do a hard reset to factory defaults, connect via a dedicated cable connection and then reapply my custom settings (either manually, or from the config file.)  However at this stage I have no confidence that the device will have web access after reset - and then it won't be working for me at all!
 
Does firmware version 2.00.21 require http access via a specific port (i.e. not 80)?  Is there some other way I can access the device for modifying configuration, other than by the web utility?  (I have posted another question about obtaining a copy of my long-ago-misplaced Setup CD-ROM. 

View 4 Replies View Related

Linksys Wireless Router :: WRT300N Will Not Reboot?

Aug 20, 2012

I unplugged my router and when I plugged it back in, it stopped working. The 4 port lights and the ethernet light come on immediately when I plug it in instead of the normal boot sequence.
 
I tried resetting it, leaving it unplugged for long periods, using the power supply from my other router,... nothing works.

View 6 Replies View Related

Linksys Wireless Router :: WRT300N For Connecting PS3 Through Wi-Fi

Aug 8, 2007

Just got WRT300N for connecting my ps3 thru wi-fi. I got everything works but the signal that I got from my PS3 is around 50% only. I am using latest Linksys firmware. My ps3 is located around 25 feet away one floor down from my wireless router. But there is no major wall inbeween the connection. My WRT300N should be a cutting edge product for networking. How come I still got 50% signal strength? Besides moving the router or pS3 closed to each other.

View 5 Replies View Related

Linksys Wireless Router :: Latest Firmware For WRT300N V1.0?

Apr 25, 2012

I have WRT300N V1.0 with Firmware v1.03.6.what is latest Firmware for WRT300N V1.0 and where I can get it.I tried at Downloads under Support in Cisco website but it said "No firmware/driver download available".

View 1 Replies View Related

Linksys Wireless Router :: Finding 1.0 Or 1.1 Firmware For Wrt300n?

May 16, 2012

i looked everwhere for the firmware. cant find it anywhere. looking for 1.0 or 1.1 firmware for wrt300n.

View 4 Replies View Related

Linksys Wireless Router :: Can't Upgrade WRT300N V2.0 With Old Firmware

Jun 16, 2011

PS Linksis Online Support said they do not have old firmware andgives me some phones to call .. Others have written about the same problem, saying that prior toupgrade with new firmware to be flash with 2.0.14.I need firmware - version: 2.0.14, where to find it?

View 9 Replies View Related

Linksys Wireless Router :: WRT300N V1.1 Is Firmware Upgradable?

Feb 8, 2013

I  need to be able to setup to 5 external ip addresses. I was told to do this you need   one to one NAT. I don't know if my router has this or not and if not is it possible to upgrade the firmware for this feature? the router I have is a linksys WRT300N V1.1  firmware : Firmware Version: v1.51.2 

View 1 Replies View Related

Linksys Wireless Router :: Wrt300n Linked To Wrt150n?

Aug 6, 2011

In my home I have a cable modem wired to a links wireless router a wrt 300n in my office (only hardwired used in there) and I do not get such good distance to my back bedrooms with my laptop. I have run a Ethernet cable dead center of the house for my sat receiver that is connected and wired to the 300wrt. Here is my question can I use the 150 like a hub or switch at the office connected to the cable modem and use the wrt300n router so that I get wireless on that side of the house. Or in reading here I see I can maybe use a bridge. I do have a older Linksys wrt150n sitting in a box.I have read until my eyes are almost bleeding and am not sure. How I can get a better signal on the other side of the house.

View 4 Replies View Related

Linksys Wireless Router :: Way To Access Set Up Page For Secondary WRT300N

Aug 13, 2012

Since the secondary router WRT300N uses the same default IP 192.168.1.1 as the primary installed router EA4500, any attempt to log onto the set up page results in diversion to the Cisco Connect Cloud for the primary router.
 
Is there a way to access the set up page for the  secondary WRT300N, bypassing the main router intervention via the Cloud  software?

View 3 Replies View Related

Linksys Wireless Router :: Unable To Connect To WRT300N Using Web Interface

Sep 16, 2011

For reasons I will explain in a separate thread, following a firmware upgrade to version 2.00.21, I am no longer able to connect to my WRT300N using the web interface.  The device seems to be working fine (but for the lack of the web config access.)  I'm loathe to leave it "inaccessible" and would like to use the Setup CD-ROM described in the manuals to connect directly to the device to see if I can fix the problem.
 
I have been through my "filing system" (read "junk room") to try to find the original device packaging, wherein I am sure I would find the original CD-ROM. Is there anywhere I can download an image of the original Linksys Setup CD-ROM for the WRT300N version 2.0 device?

View 7 Replies View Related

Linksys Wireless Router :: WRT300N Losing Over 50mbps Of Speed?

Jan 22, 2013

So lately my internet has been painstakingly slow, Youtube videos dont load, Web Pages take FOREVER, its killing me. So I ran some speed tests This is wireless over my router. (WRT300N (Yes i know its old))
 
And this is direct connetion from my modem this really just makes me want to never use the internet again.

View 9 Replies View Related

Linksys Wireless Router :: WRT300N - Air Ave Access Point For Sprint

Mar 8, 2012

I have a WRT300N wireless router that was working fine until I tried hooking up an Air ave Access Point for Sprint.  Now the router doesn't work at all - even the hard wired connections don't work.  I tried the usual - unplugging, plugging back in, disconnecting, reconnecting, hitting the reset button - nada. 

Removing the Air ave Access Point doesn't matter - it still doesn't work when I put it back the way I had it before.   The only way I can get a signal to my computer is to plug it directly into the modem, bypassing the router.  

View 1 Replies View Related

Linksys Wireless Router :: WRT300N - Can't Play Online On Xbox Live

Jan 15, 2012

Why I can't play online on xbox live. I'm set on going online but when I go on to play online for MW3(Modern Warfare 3) my NAT Type says strict,I can't join any of my friends games. It says to go on infintyward.com/Nat and when I do it doesn't show my model of linksys (WRT300N) i reset my xbox,my router and still nothing

View 3 Replies View Related

Linksys Wireless Router :: Cannot Connect Canon MP620 Printer To WRT300N V 1.1

Oct 10, 2009

I cannot seem to figure out how to connect my Canon MP620 Wireless printer to my wireless router.  The router is a WRT300N v 1.1 with the latest firmware upgrade.  I am using WPA for security. I can connect to the printer wirelessly through my neighbor's open system so it has something to do with security I suspect.  I have enabled the AP feature and disabled it to see if that is an issue.  That has not changed anything.  I have looked at other posts with HP printer issues  and access point posts but none of those solutions have worked.  The Canon gives me an option to use the WPA, WPA2 and WEP?

View 3 Replies View Related

Linksys Access Point :: Can WRT300N Wireless Router Be Used As LWAPP Device

Nov 28, 2011

Can a Linksys WRT300N wireless router be used as an LWAPP AP device?  

View 1 Replies View Related

Linksys Wireless Router :: WRT300N - Slow Speed And Low Ping Test?

Aug 18, 2007

I have installed a WRT300N on to a new machine and the connection speed reads as 1 Mbps (not 100 but 1 ).  I did a ping test and the results are

View 2 Replies View Related

Linksys Wireless Router :: WRT300N Not Providing Internet When DHCP Disabled

Apr 5, 2012

Here is where I want to go:
 
Windows server 2008 (providing DHCP and DNS) 192.168.89.1 on all
Cisco SG 300-20 (switch) 192.168.89.3
all Clients(15 x DHCP assigned IPs) connected to switch
WRT300N(192.168.89.2) connected to switch
Internet modem connected to WRT300N
 
To achieve this I need to disable DHCP on the WRT300N, since my server is providing DHCP.The issue I have is that when I disable DHCP at the WRT300N, I lose internet connection (connected to either switch or direclty to WRT300N).

View 6 Replies View Related

Linksys Wireless Router :: WRT300n Version 1.1 - Power Light Blinking

Aug 15, 2011

If I conact from the modem to the pc I have internet so it must be the router.  The power light is blinking along with all the port lights.  Power light is blinking one time slow 2 fast.  Have tried holding the reset button for 30 seconds and unpluging for 30 seconds.   Can not go to the ip address it times out.  New firmware is not avalible.

View 9 Replies View Related

Linksys Cable / DSL :: WAG160N Modem Just Dropped Wireless Connection Constantly In Various Time Period

Sep 28, 2012

I've bought a "WAG160N v1.0 Annex A" almost 2 years ago. I never used it's wireless feature untill we moved our house. Now it's like 4 month I'm using its wifi feature and I've got to admit I'm really frustrated by its functionality!
 
For months the modem just dropped wireless connection constantly in various time periods. Somtimes it went like 2 days without any problem but some other times I had to change channel every 15 minutes for it to get back working. And yes it didn't get fix until I changed the channel, otherwise clients had to wait several hours for a 50/50 chance of reconnection. Now It's two days the changing channel trick no longer works. I tried all channels and even put my notebook next to the modem but no luck. The notebook sometimes connnects to the access point but disconnects after a few seconds. Somtimes it doesnt even detect the SSID of my WAG160N modem. Some friends suggested that the wireless hardware of my modem is broken and no longer works but I'm eager to know if it is broken why is it still broadcasting and sending signal.
 
I've tried everything from upgrading and downgrading firmware to turning on and off the modem several times and changes modem position. And even tried the G-only 20MHz mode.We are at a very crowdy place. Using inSSIDer I could pick about 15 other access points. Only few of them are using Wireless-N, most of them are using Wireless-G.This is the inSSIDer diagram of my WAG160N modem from a client: [code]

View 5 Replies View Related

Linksys Wireless Router :: Connecting WRT300N To Uverse Gateway - Dynamic IP Address?

Feb 6, 2012

I have a WRT300n router and want to connect to my Uverse Gateway. When I connect them & try to use the internet connection I get an error that says a connected router must be capable of using DYnamic IP addresses.

View 1 Replies View Related

Linksys Wireless Router :: WRT300N Power Light Dim And All Other Ports Solid Green

Nov 20, 2011

I have a WRT300N and the power light is dim and all 4 ports are solid green along with the internet light being solid green.. Nothing else is plugged in.. Just the power.. I have tried to hard reset and nothing happens.

View 2 Replies View Related

Linksys Wireless Router :: E4200 Completely Quits Periodically

Sep 14, 2011

I purchased an E4200 from a retail store about ten days ago.It completely quits periodically. Even the managment interface is gone. It seems to just die. The only fix is to unplug it, count to ten and plug it back in.router also gets extremely hot. I have tried locating it in several places, no matter where I put it, it still gets very hot. Right now I have it straddling a trash can so that it has about two feet of air space under it. It is still uncomfortable to the touch.
 
When I contacted technical support all they would do is walk me through setting it up from scratch again. I've done that many times, and I do not want to do it agian. Setting the router up agian will not make it cool down.
 
1. Exchange this for another one, probably from the same batch, at the store?
2. Fight with Linksys tech support to get a waranty return? (Any input on how to get them to do this?)
3. Return this router altogether (paying the retailer's 15% restocking fee) and look for another brand?

View 8 Replies View Related

Linksys Wireless Router :: WRT300N - Reconnecting To Modem While Retaining All Current Security And Settings

Feb 24, 2012

Comcast service went down in our neighborhood and when it came back up my internet was down and all five LED lights on my Linksys router are solid green. Tech support tells me that I have to reset the unit to get it to function again.It's been a very long time since I set up the home network and while I'm pretty sure I can make my way through setting up from scratch (I'm assuming resetting goes back to factory settings)  I was hoping there was a way to reconnect the router to the modem while retaining all the current security and settings.

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved