Linksys Wireless Router :: Cannot Connect Canon MP620 Printer To WRT300N V 1.1
Oct 10, 2009
I cannot seem to figure out how to connect my Canon MP620 Wireless printer to my wireless router. The router is a WRT300N v 1.1 with the latest firmware upgrade. I am using WPA for security. I can connect to the printer wirelessly through my neighbor's open system so it has something to do with security I suspect. I have enabled the AP feature and disabled it to see if that is an issue. That has not changed anything. I have looked at other posts with HP printer issues and access point posts but none of those solutions have worked. The Canon gives me an option to use the WPA, WPA2 and WEP?
View 3 Replies
ADVERTISEMENT
Nov 18, 2012
I have a desktop running XP. I am using comcast as my ISP. I have my printer attached to my Linksys wrt160N router via Ethernet. My desktop is also attached via ethernet. I also have a laptop attached to the router via wireless. How do I access the printer via the router from either the desktop or laptop? I had it configured properly in the past then lost my motherboard. Once the PC was rebuilt, I lost access.
View 6 Replies
View Related
Dec 25, 2012
We purchased a Canon MG 3100 printer but am unable to connect. Have rebooted router but still no joy.
View 5 Replies
View Related
Jan 8, 2013
I want to be able to connect my Canon MX700 printer via ethernet cable to my Linksys Router - WRT54G2, with the ultimate goal of having only the printer and router on, and able to print wirelessly from my iPad, MacBook and/or iPhone.
View 5 Replies
View Related
Jan 8, 2013
I want to be able to connect my Canon MX700 printer via ethernet cable to my Linksys Router - WRT54G2, with the ultimate goal of having only the printer and router on, and able to print wirelessly from my iPad, MacBook and/or iPhone.
View 1 Replies
View Related
Nov 26, 2012
I can't seem to get my Canon MG5220 Wireless Printer to connect to my Belkin N150 wireless router. The printer sees the belkin wireless router network name but cannot connect to it( after entering the correct security key). It worked fine with a previous wireless router. My desktop PC is connected to the belkin router via direct ethernet, and I want to be able to access my wireless printer which is located in another room from my PC. I think I remember reading that the canon mg5220 may not support WPA2 security, but Its only a year old and would prefer not to regonfigure my router's security setting. how I can get this printer to connect to my router? Any other ways to access this printer from my PC which is connected to LAN via ethernet?
View 3 Replies
View Related
Jan 28, 2011
Can I connect my Canon iP6600D printer (USB 2.0 interface) to an Ethernet port on my wireless router so as to end up with a network printer?
View 1 Replies
View Related
May 7, 2013
I have recently updated linksys ea4500 router with smart Wi-Fi firmware and installed USB printer with cisco usb software .on my laptop with windows xp on Wi-Fi it is working fine but on other laptop with windows 8 on wifi it is keep on connecting and disconnecting in status bar it shows unexpected disconnection.i want to use this printer from both laptops on wireless when ever needed
View 1 Replies
View Related
Mar 23, 2012
Any way beside the standard router/printer rebooting, firewall disablity. I am able to connect to my first laptop on which I installed all the drivers on but when I try to add an additional windows 7 laptop
View 2 Replies
View Related
Jan 15, 2013
do I need USB cable connected all the time to printer and laptopto print?
View 1 Replies
View Related
Feb 28, 2012
I have a Canon wireless printer, but I forget the password for conection to my laptop.What should I do?
View 1 Replies
View Related
Oct 20, 2012
I currently have Canon MX870 pixma printer - it is wifi enabled. A few weeks ago it went offline and I was able to reconnect it by entering the "access point" and password in printer control panel. It has once again gone offline however the printer cannot locate the access point by searching and when entered manually returns a message that it cannot locate the access point as entered. I am having the same problem with my TV which is also wireless connected, i.e., the TV is not connected to the internet and I cannot locate the network name (access point) in the setup menu on the TV. I had also previously reconnected the TV by entering the network name manually.
I tried looking in the router - Linksys Wireless-G 2.4 but cannot figure out where this information should be located. There is a setup tab in the router administration and both the Host name and the Domain name are blank. The router admin page states that: Host Name : Enter the host name provided by your ISP. Domain Name : Enter the domain name provided by your ISP. The wireless tab states: Status: SES Inactive. Does this mean anything?
Computer is a Dell Inspiron 620 running Windows 7 Home Premium
View 4 Replies
View Related
Mar 1, 2013
I am trying to setup the wireless printer (Canon MX436) to my ACER laptop (windows 7).
I am not very techincal and the instructions say to "Press and hold the WPS button on the access point (for about 5 seconds)." but have no idea what this means.
I know the laptop has the wi-fi turned on but when the printer searches it doesn't find it.
View 1 Replies
View Related
Sep 16, 2011
For reasons I will explain in a separate thread, following a firmware upgrade to version 2.00.21, I am no longer able to connect to my WRT300N using the web interface. The device seems to be working fine (but for the lack of the web config access.) I'm loathe to leave it "inaccessible" and would like to use the Setup CD-ROM described in the manuals to connect directly to the device to see if I can fix the problem.
I have been through my "filing system" (read "junk room") to try to find the original device packaging, wherein I am sure I would find the original CD-ROM. Is there anywhere I can download an image of the original Linksys Setup CD-ROM for the WRT300N version 2.0 device?
View 7 Replies
View Related
May 25, 2012
I am trying to connect a Canon printer wirelessly to my system and it will not connect. What can I do to connect it?
View 1 Replies
View Related
Mar 21, 2011
I have a printer canon 2230 i want to canact via network cabel throw switch ,then i want to sarching printer then show workgroup and next proces is not go.
View 1 Replies
View Related
Oct 9, 2011
I have a canon ipf6350 printer that I want to move to another room in my house. It is currently connected via a network cable connected directly to my wifi router. The printer does not have wifi. how can I connect the printer to the network once it is in another room? I have an older belkin n1 vision wifi router I am not using. Can I connect this wirelessly to the existing network and then plug a cat 5 cable from the belkin to the printer?
View 5 Replies
View Related
Sep 16, 2012
Canon lbp 2900 attached on windows 7 32 bit system,i want to shared this printer on another system(windows 7 32 bit).
View 1 Replies
View Related
Dec 21, 2011
I move to new house recently and found out that my new house doesn't have wireless or WiFi connection. I have Canon MP560 printer that need WIFi connection and I couldn't find out how to connect it to my computer. How to connect it to computer without using wireless connection?
View 1 Replies
View Related
May 10, 2011
There's a Canon LBP 3500 printer on my office network.I don't know its IP.It doesn't show up when I scan the local subnet with nmap.I cannot find the manual (hardcopy or online).It is plugged into the network.It is turned on.I have turned it off and on again.I have tried plugging it into other ports on our switch.
View 1 Replies
View Related
Jun 24, 2012
The printer seems to recognize the wifi but won't connect, even tho I am following instructions to hold down the WPS key before clicking "OK" on the printer.
View 1 Replies
View Related
Aug 18, 2011
..how many PCs are allowed to connect to the printer via printer sharing? Is it unlimited?
..the printer are connected to the main PC
printer : Canon Laser Shot LBP-1210
View 2 Replies
View Related
Mar 21, 2011
I have 2 desktops (running windows 7), a Canon MF8300 printer, and an outgoing ethernet line, all on a Netgear Advanced Cable Modem Gateway CGD24-CPR. I'm only concerned with having the 2 desktops set up with the Canon printer.Both computers have been connected to the printer before and I have the startup disk. But once the new offices were set up and both of the desktops were moved, I can no longer access or find the printer.
I can IPconfig the Desktops for their IPV4 addresses and both desktops recognize eachother on a Homegroup, but I can't find the printer. I printed off the print configuration page from the printer which gave me an IP address (printer is set for auto-obtain), but using an IP search won't bring up the printer.All of the devices are plugged into ethernet ports set up for the three different office they are in and the actual location of the Netgear cable modem/router is over 100 feet away. My primary concern is getting the printer for the desktops, but I also need to add a wireless router into one of those office in the future.
View 15 Replies
View Related
Jan 21, 2013
I have a Canon i9900 printer wired to an XP desktop. I bought a new windows 7 laptop that connects to the internet through my wireless router. How do I setup the laptop to print through the router?
View 2 Replies
View Related
Sep 26, 2012
Have a Canon MG6120 wireless multifunction printer. I rarely print anything from my laptop, but wanted to do that today. What I get is an error message that the printer is offline -- which it isn't; it's on. I tried going thru the setup on the printer, re-entering the SSID, and it said it was connected. Still same error that it's offline.
About a month ago, I did change the name of my router, but it never cause a problem with printing from my desktop, which I can still do. It's just the laptop that gets the "offline" error.What do I need to do to make the laptop recognize that the printer is on?
View 1 Replies
View Related
Jun 18, 2012
is there any way i can make my canon printer i9900 wireless?
View 1 Replies
View Related
Feb 20, 2012
I just bought a canon pixmaMG6120 wireless printer...hooked it up to our wireless network (via a netgear wg624v3 wireless router). pritner recognizes the network, can sign into the network and has an IP in they systems setting. i can print to it via my iphone and ipad (all on the same wireless network).my HP dv6 laptop doesnt recognize a printer is on the network though. i've tried using the included cd, tried doing it via IP address, tried taking down all the firewalls, and nothing seems to work.
View 4 Replies
View Related
Nov 27, 2012
I can't seem to get my Canon MG5220 Wireless Printer to connect to my Belkin N150 wireless router. The printer sees the belkin wireless router network name but cannot connect to it( after entering the correct security key). It worked fine with a previous wireless router. My desktop PC is connected to the belkin router via direct ethernet, and I want to be able to access my wireless printer which is located in another room from my PC. I think I remember reading that the canon mg5220 may not support WPA2 security, but Its only a year old and would prefer not to regonfigure my router's security setting. how I can get this printer to connect to my router? Any other ways to access this printer from my PC which is connected to LAN via ethernet?
View 1 Replies
View Related
Jan 21, 2013
Recently i converted a customer's APs to LWAP and installed a 2504 WLC. Everything came up and is acting good, but the printer is no longer printing. It can neither be discovered using windows networking, nor bonjour. It worked until LWAPP conversion.
It is an AirPrint device, a Canon mx892. Trying to print using an IP port fails, AirPrint fails, and sharing it through the attached Mac also fails. I dont know enough about printers or AirPrint to effectively troubleshoot. The customer opened a case with Canon, who says its a network issue. I cannot get it configured on the wire, apparently setting up a printer isnt as easy as it used to be.
View 1 Replies
View Related
Sep 16, 2011
After enduring some protracted problems with wireless connectivity, I decided to bite the bullet and upgrade my Linksys WRT300N from firmware version 2.00.08 to 2.00.21.I found the links to advice on how to achieve this, via a two-stage upgrade url...I followed the following steps: Upgrade firmware using file "wrt300n.bin" file, as per the above link. This brought the firmware version to 2.00.17. Upgrade went smoothly - config page refreshed after rebooting the router and all was well.Upgrade firmware using file "WRT300N-EU-ETSI-ML-2.00.21-code.img" file, downloaded from the Linksys support site. Again, the upgrade went smoothly (apparently) ... except that after rebooting the router, my config page failed to refresh.I have since powered the router off (wait 30 seconds) and on again. Still no web access.
The device, however, does seem to be working OK. I have wireless access, and wireless access, via computers on my network. The only thing I cannot do is access the web config page - but that's not quite satisfactory. I have a number of customised settings on the device, saved to a config file. Included among those is a changed IP address for the router of 192.168.1.10. I am tempted to do a hard reset to factory defaults, connect via a dedicated cable connection and then reapply my custom settings (either manually, or from the config file.) However at this stage I have no confidence that the device will have web access after reset - and then it won't be working for me at all!
Does firmware version 2.00.21 require http access via a specific port (i.e. not 80)? Is there some other way I can access the device for modifying configuration, other than by the web utility? (I have posted another question about obtaining a copy of my long-ago-misplaced Setup CD-ROM.
View 4 Replies
View Related
Aug 20, 2012
I unplugged my router and when I plugged it back in, it stopped working. The 4 port lights and the ethernet light come on immediately when I plug it in instead of the normal boot sequence.
I tried resetting it, leaving it unplugged for long periods, using the power supply from my other router,... nothing works.
View 6 Replies
View Related
Aug 8, 2007
Just got WRT300N for connecting my ps3 thru wi-fi. I got everything works but the signal that I got from my PS3 is around 50% only. I am using latest Linksys firmware. My ps3 is located around 25 feet away one floor down from my wireless router. But there is no major wall inbeween the connection. My WRT300N should be a cutting edge product for networking. How come I still got 50% signal strength? Besides moving the router or pS3 closed to each other.
View 5 Replies
View Related
Apr 25, 2012
I have WRT300N V1.0 with Firmware v1.03.6.what is latest Firmware for WRT300N V1.0 and where I can get it.I tried at Downloads under Support in Cisco website but it said "No firmware/driver download available".
View 1 Replies
View Related
