So we just had Att Uverse installed in our apartment and the 2wire box has not been too reliable. I was trying to set up my Linksys router to provide an additional wireless network but i was having some problems with the set-up
View 3 RepliesI have a WRT300n router and want to connect to my Uverse Gateway. When I connect them & try to use the internet connection I get an error that says a connected router must be capable of using DYnamic IP addresses.
View 1 Replies View RelatedI am using my wireless adapter..a Linksys AE1000..to connect to a friend's ATT U-Verse high speed internet for a few weeks. Due to a petty argument with his girlfriend..I overheard her and her friend and discovered that she had logged into the Uverse router/modem (192.168.1.254), which shows all devices that are connected. On this page it has links to access files for each device. Clicking on that, she was able to read all my files. Nothing to hide, I just don't like snoopers and even wonder if she could change settings or do something to mess up my computer. I cannot figure out how to block access by her Uverse thru my Linksys wireless adapter.
I normally do not allow any sort of file sharing and everywhere I have looked on my PC, nothing is enabled to file share or remote desktop share or anything like that. I'm not a total noob but have no clue if and how I can change this on my end so that she cannot get into my PC while I'm connected to their internet. Their router/modem is a 3800HGV-B.
I recently swapped out an RV082 with a newer model (still RV082 but black and a different interface). I configured the Gateway to Gateway VPN exactly as it was before but none of the three other RV082's will connect. I have tried deleting the connections several times to no avail. I have aggressive mode disabled and have tried with the firewall on and off. Below are the settings (IP's have been X'd out) and the log.
Settings:
IP OnlyIP Address : X0X.X0X.20.31Local Security Group Type : IPSubnetIP RangeIP Address : Subnet Mask : Remote Group Setup
Remote Security Gateway Type : IP OnlyIP AddressIP by DNS Resolved : Remote Security Group Type : IPSubnetIP RangeIP Address : Subnet Mask : AES-192AES-256AES-128 AES-192AES-256 AES-128 IPSec Setup3DES Keying Mode : ManualIKE with Preshared keyPhase 1 DH Group : Group 1 - 768 bitGroup 2 - 1024 bitGroup 5 - 1536 bitPhase 1 Encryption : DES Phase 1 Authentication : MD5SHA1Phase 1 SA Life Time : secondsPerfect Forward Secrecy : Phase 2 DH Group : Group 1 - 768 bitGroup 2 - 1024 bitGroup 5 - 1536 bitPhase 2 Encryption : NULLDES3DES Phase 2 Authentication : NULLMD5SHA1Phase 2 SA Life Time : secondsPreshared Key : Minimum Preshared Key Complexity : EnableLOG:
[code].....
My two RV042 , one at home and the other one at my working site, constantly lost VPN connection after successfully connected.Both Firmware are identical. [code]
View 1 Replies View Relatedwe do have 2 Rv042, one in my office and one in my house.. in the office we do have static ip and at home none.. question is can i connect the two RV042?
View 1 Replies View RelatedI have some problems in my network with Gateway to Gateway Vpn Connection using two Rv042 routers.
I cannot ping the computers with static ip configuration.
In local an remote computers who have DHCP ip configuration i can ping each other .
We have a VPN setup between two Cisco RV082 routers, the VPN status shows as connected however I can't ping the other network. I am unable to ping between routers, let alone ping computers behind those routers.
We have 2 branches, branch 1 is on a static IP and branch 2 is Dynamic. I am able to connect via QuickVPN from Branch 2 to Branch 1 and remote desktop to computers, however have yet to VPN/remote desktop in the opposite direction.
To me it seems like a firewall issue at branch 2, but what's causing this. Also they are currently running 2 differnet firmware version not sure if this would cause a problem.
i am trying to setup a vpn Gateway To Gateway when i setup the vpn i can ping the 2 rv042 i cant see any computer in the network places when there comect we need to see the computer in the network places so are pos will run?
View 1 Replies View RelatedI have an RV082 and a RV042. I have been able to successfully establish a gateway to gateway vpn connection between them both, and I can remotely administer each router through the VPN connection, but I am unable to ping computers from one side of the connection to the other. For example, a computer in the 10.10.1.0 subnet can't see / ping / communicate with a computer in the 192.168.1.0 subnet.
Below are the configurations for each. Aside from the static IP configurations and the VPN configurations, no other changes were made to the routers. RV082 DHCP Enabled Tunnel Status: Connected Local Group Setup
IP Only: X.X.X.66Local Security Group Type: SubnetIP Address: 10.10.1.0Subnet Mask: 255.255.255.0Remote Group Setup
I have been trying to connect to my 2Wire Uverse wireless router and it not going well. I had it connected and for other reasons I went into the router setup and disabled wireless, did nothing else. When I enabled wireless again (and did nothing else) I could not connect my Win 7 computer. Everything else connects just fine so I know it's not the router but this Win 7 computer.When I click on the connections icon it shows me all the available wireless networks and the Uverse show but has a red X on it and the popup says something to the effect it's trying to connect but the connections are not the same as are in the profile or the info.
View 14 Replies View RelatedI've been having some trouble with my ATT router. I've had it for months and there have never been any issues until now. It does not seem that it is broadcasting WiFi like usual. It will not show up on the WiFi network list on both my iPod and my laptop. I've tried resetting the router (by unplugging it and plugging it back in).
View 5 Replies View RelatedWe've had UVerse for about a year now - but lately we've had weird problems:
-about every 2-4 weeks, the router will spend a night constantly locking up and rebooting itself. ATT says they don't know why, and wanted me to check the power?? When it does this, it will do it for 30 minutes to TWO HOURS.
-every couple of days, the channels will freeze. If we change channels and then back, it returns to normal for a bit. Sometimes for a while, sometimes only for a minute. We have two boxes, each one does it. Even affects DVR playback. Internet doesn't seem to be affected, so I had originally though it was the boxes. ATT has remoted in, and can't find anything out of the ordinary.
I have att uverse which is wireless G. I want to add a 2nd router behind it that will have wireless N. I've made the connection. I see it on my list of networks but doesn't allow me to access it.
View 2 Replies View RelatedI have ATT u-verse currently and it connected to a router but I am going to need several more gigabit ports so I wanted to get an 8 port gigabit switch. I would plan on running a cable from my U-Verse modem to my router then to my switch giving me wireless and 8 gigabit ports. Would that work? I've never done this before so I wasn't sure if I was missing something or not.
View 2 Replies View RelatedI have a compaq laptop running Vista. We recently had our Uverse wireless router/modem replaced. Now my laptop will not connect to the internet. The laptop connects to the router but shows up as local connection only. Uverse tried all kinds of differant things to no avail. The laptop will hookup with a USB modem but I would like to get it back to how it was before.
View 14 Replies View RelatedTrying to set up the Cisco VPN router for remote acces to our network.We have ATT Uverse DSL and it is a Motorola Router, i think NGT 510.the Uverse router has very limited setup options.I cannot set it up as a bridge.The only thing I can figure out is to set the ip passthrough option to the VPN router.We have a static ip address for our internet service.
I have tried several setup and connection options, but cannot get it to work.
1. How to physically connect the routers and network devices?
2. How to setup both routers to play nice.
I need to increase my wireless speed higher that what Uverse gateway is supplying. Want to install a 802.11 N router behind the uverse gateway and disable the uverse wireless. Uverse gateway will allow this.
View 4 Replies View RelatedCan a router using OSPF propagate that he is a router with default-information originate... at the same time when he got an own gateway of last resort to an IP-adress? If so, how? I can't get it to work.
View 8 Replies View RelatedI am having problems with my linksys wireless G ADSL gateway WAG54GS router. I am on Windows Vista/Internet Explorer. When I set up the router to work on the internet when I first bought it (several years ago), something must have gone wrong in the installation because it works only when connected to the computer by the lead, and NOT wirelessly.
While this is fine for general internet browsing etc on the main computer, my problem now is that I cannot connect anything else to it (such as my Playstation 3) because the router does not work wirelessly and I do not have the WPA key that the PS3 asks for. Is there any way can fix this without doing a complete reset on the router?
[ALSO: the router also periodically goes wrong, e.g. loses connection for no reason at all - I often have to disable and then enable the internet connection, or turn the router off for 15 seconds then switch it on again, and then it's fine again. I live in a rural area though, so it might be because of a poor connection. Our telephone connecton isn't very good either and sometimes goes wrong.]
I currently have Comcast as my ISP.However there are only 4 wired ports on the router and I need an additional 2 ports for my needs. I have a 2wire 38000HGV-B Uverse Wireless gateway. I wanted to know if I could use one of the output ports from the Comcast wireless gateway and feed the 2wire Gateway to achieve the additional ports that I need. Also the wireless router from comcast is so difficult to setup that I don't even use the wireless. The 2wire gateway is much easier to setup and use and I could have wireless available where I don't have it right now.
View 2 Replies View RelatedI've recently bought a WRT120N router, when I install the router using the CD an error occured error 322 New router or gateway not detected. I tried to download new version of firmware but it didnt work.
View 9 Replies View RelatedI can't log into the router. Get 502 Bad Gateway - Model EA4500; Have a USB Drive connected to the router.
Power-off and Powered-Back on - no change.
I have a WRT54GX2 router and my laptop is connected wirelessly to the router. It worked fine before but now, the connection is only local, it's not connected to the internet.On the router, it says: Default Gateway: 0.0.0.0.I think that it should say 192.168.1.1 instead.I tried dhcp release and renew but it didn't work.The firmware version is 1.01.22.
View 3 Replies View RelatedI am currently using an E900 wireless router. The router is on the second story so I have to use a wireless router booster to enhance the signal strength. I have been using the booster for well over a month with no issues whatsoever; however, tonight I attempt to get onto World of Warcraft and I keep getting disconnected every 5 minutes. After I run the diagnostic it fixes the problem and says that the "default gateway not available". I tried restarting the router, restarting the booster, unplugging the wireless adapter, checked the firewall, and also restarted my computer.
View 2 Replies View RelatedTrying to login to my router with the default IP address of http://192.168.1.1
Been working fine forever.. I went in and dumped all my cache on my browers IE and Firefox.
Still getting this error. I have unplugged the router and cable model and also restarted the computer.
This seems to be a recent issue since it was working a few days ago..
I am setting up an RV042 for my small business office and I am trying understand how it needs to be configured.
-For WAN1 I have a Wildblue Satellite Modem connected IP 70.66.93.4
-For WAN2 I have a Cradlepoint CTR35 Router with a verizon AirCard Connected IP 192.168.0.1
(Verizon has a 5GB download limit and wildblue has a 17GB download limit but it drops out in poor weather)The LAN is IP 172.16.0.1 Subnet Mask 255.255. 255. 0Should I set the RV042 up as a gateway or as a router?
I have been using this router for the last six months and never had a single problem. Then yesterday out of nowhere internet stopped working and I was not able ping my ISP gateway (both wired and wireless) [Received: Destination host not reachable on both Windows Vista / 7]. Rebooted the router but still no luck. Unplugged / Replugged the net connection from the WAN port and then finally ping was successful.Now the weird this is every time I power on the router the Internet does not work and ISP Gateway seems not reachable, but if I unplug/replug the WAN connection the ping reply starts and internet works without any problem.
View 3 Replies View RelatedI am looking to replace my current WAG54GS Gateway with the EA6500. Problem is the new one does not have a built in ADSL2+ modem (I am in the UK and my ISP is Demon Internet). I therefore need to purchase a separate Modem to connect to the router.
View 9 Replies View RelatedI have a Linksys E3000 and I see the gateway (192.168.1.1) listed in my DNS server addresses.
1. Why is this listed here in the DNS?
2. How do I remove it from my DNS servers or stop the router from inserting it into my DNS server list?
FiOS gave me an Actiontec router that every other day is getting into a state where it refuses to give out IP addresses via DHCP. I have to reset the router to get it to work again.This seems ot have started in the last year, I assume due to some piece of equipment I added, or perhaps the VPN software or Windows 7 installed on my work laptop. I've not been able to figure out what is tripping up the Actiontec router, so I decided to try moving the DHCP function over the WRT610N that I have. I basically had the WRT610N setup without DHCP enabled, no NAT and no RIP, so it was basically just working as an access point. I left the Actiontec at 192.168.1.1 and assigned 192.168.1.2 to the WRT610N on the LAN side, while the WAN side is left disconnected.
I disabled DHCP on the Actiontec and enabled it on the WRT610N. I also set the DNS server to 192.168.1.1 so it would go to the Actiontec for name resolution. Using nslookup from a command prompt on a PC wireless connected to the WRT610N, I can see that names are indeed getting resolved. However, it looks like the WRT610N is setting itself up as a the gateway at 192.168.1.2. When trying to ping something out on the net, I get a message back saying that 192.168.1.2 is reporting the address as unreachable.
I assume this is because the WRT610N is handing out its own address (192.168.1.2) as the gateway. Is there anyway to get the WRT610N to hand out a different gateway address than itself? Optionally, is there a way to get the WRT610N to route requests coming to it over the Actiontec?I suppose I could just ditch the Actiontec altogether, but it seems a bit easier to use to setup port forwards and the like for various servers we have running. It also has a coax MoCA interface which I believe our FiOS set-top boxes use for their internet connectivity, so I don't want to lose that.
I bought this wonderful voice gateway off the internet from someone. So not sure if they ever used it with Comcast.So far I hatve had no internet once I plug it to the cable. I have asked Comcast tech for activating this device. However they say it is not supported and they have tried sending it the Activation signal but they say it fails. I can see all lights lit up and go green when I connect this device to the cable, is there a firmware upgrade for DPQ3925 ?
View 2 Replies View RelatedI'm unable to access my linksys wireless g broadband router (WRT54G)'s access gateway. (192.168.1.1)The gateway page doesn't load, at all. It doesn't ask for the user or password at all. On any of my internet browsers (firefox, and internet explorer)Anyway of fixing this would be appropriate.
View 2 Replies View Related