I would like to know what ip addresses I should see in this table. Shouldn't my default gateway IP have the same mac address as my computer or router? There are 2 different ip address/mac addresses from different a ISP than mine. I have a cisco DPC3825..I suspect a someone is spoofing my DNS.
View 4 Replieshrome threw me a DNS lookup failed. I go into my network settings and I noticed that I had limited connectivity. It would switch between no network access and no internet access every few seconds. After a bit of fiddling around, I got it to connect through assigning myself a static IP. This isn't exactly convenient because I use this computer on multiple networks. When I try to have it on automatic IP, I get no IP address or default gateway when I do an ipconfig /all. It would appear that my router quit assigning my laptop an IP for no reason whatsoever. DHCP is enabled on the router, and all other devices work fine. What could possibly be the problem here? I'm 99% sure it's not an IP conflict either. It's not being MAC filtered because I'm on the thing right now posting this through a static IP. It's not my A/V because it's worked great in the past. Perhaps I should also mention it occasionally says "unidentified network" instead of the SSID
View 8 Replies View Relatedi have a dpc3825 cable mdem gateway i spent 4 hours on the phone with charter yesterday i cant access the admin part of the router i go to 192.168.0.1 and up comes the setup username and password i have reset it numerous times i have left it blank as per instructions i have tried admin and blank cusadmin and password i cant get in
View 1 Replies View RelatedMy ISP is changing out all the ADSL routers in our area and they have blocked the Default Gateway Address, so we can not access it via Web Browser. This is frustrating because they changed our Wi-Fi password, instead of just keeping what we had like an Einstein. They said they did it because of Hackers
View 2 Replies View RelatedClient is having 1 file server running small business windows server 2003. Server is not configured with domain, it is working only on workgroup. We have around 15 users who are using that server as file server only. Now my main question is do i need to configure DNS server in that server?we also have internet connection running (have problem in that also, will explain next time) with wireless router to connected with switch. So do I need to setup dns in server also or just put static ip (I prefer static then dhcp) & dns server from ip will be ok? If I put dns which I got from ISP, so will it create any problem with using those file from server?the second question is..
What IP address, Default gateway and dns address I should use for Server & also client pc.
router ip - 192.168.1.1
server ip - 192.168.1.10
Currently no DNS setupcurrent configuration - Server
IP - 192.168.1.10
subnet- 255.255.255.0
gateway - 192.168.1.1
dns - 213.42.20.20 (from ISP)
dns2 - xxx.xx.xx.xx (from ISP)current configuration - Client
IP - 192168.1.111(to 115)
subnet - 255.255.255.0
gateway - 192.168.1.1
dns 1 - 192.168.1.10 (File Server)
dns 2 - 213.42.20.20 (from ISP)
what my IP address, my subnet mask, and what my default gateway is. I have tried typing "ipconfig" into CMD but then I only got up 100 boxes saying "Permissionisconnected"
View 12 Replies View RelatedI can't print in my network printer using my Laptop (WIFI). I have check the default gateway of the desktop PC on which connected the printer and its different from my Laptop. Also I cant "SEE" this desktop PC on the LAN.
View 1 Replies View Relatedrecently, i have connected the internet to my PC with cable. Here the problem is , the packets are not receiving in the status bar of internet connection. I have checked in command prompt, the ip address is connecting properly but the default gateway ip address is showing "Request Timed Out" message.
View 1 Replies View RelatedI have a 3500 XL switch with the following default gate IP address that i need to clear from the switch but not quite shore how to remove it.
I've removed the customer original Ip for security reason as this is an open discussion forum and just replaced with 1.1.1.1
switch#show ru
Building configuration...
Current configuration:
!
[Code].....
NIB DPC3825 cable modem. Called my provider and got it provisioned and its working (I'm on an ethernet connection posting this). But when I http to 192.168.0.1, I get a screen that doesn't quite look like the one in the manual. I enter the "admin" and "W2402" and click login, and the screen refreshes but nothing happens (no configuration options, only able to check status of downstream and upstream channels). Pushing the factory reset button for ten seconds to load defaults makes the lights blink and then reboots; same result as above. Pushing the wireless config button has no effect at all.
View 3 Replies View RelatedI just purchased a Buffalo WZR-600DHP router and have been having a weird issue. When using the router on the shipped DD-WRT firmware I consistently get "The default gateway is not available" error and I have to reset my wireless adapter on my laptop. This issue doesn't occur on my hardwired desktop or interestingly enough when the Buffalo router was switched to the "user-friendly" firmware the issue didn't occur either. Both times the router was on the DD-WRT firmware I've had the default gateway issue.
View 1 Replies View RelatedDoes ip default-gateway have any effect on a L3 device such as a 2811 router? I always thought that on a L3 device the default route would supersede any such command assuming it is accepted.
We have a client device that cannot be reached for managment directly and wanted to add that statment only if it might work.
I have a 2511 TS linked into my CCNP lab and configured it with default gateway pointing to my ADSL router. The TS has a staic local IP in my LAN also I have port forwarding set up on my ADSL router to direct all Telnet (not cofigured for ssh yet) sessions to the TS.
The TS is linked to the ADSL router via the transceiver module ( CentreCom AT-210TS) which feeds the ADSL router with ethernet connection.I have tried to access the TS from a remote location but with no joy, fortunately I also have it consoled to my PC so I SSH to the PC and then run my terminal emulator from there. Using SSH to the PC and then minicom to the TS when doe this way (Remote Location>Ubuntu>minicom>TS) I can see the ethernet interface has no MAC address when i do a sh internet eth 0 mac is set to 0000.0000.0000.
I don't want to be connecting via ssh to PC before accessing the TS but instead just want to connect to the TS; for the life of me I still can't explain what's going on.
I have a central office and two branch offices, these offices are connected by a private routing service that has no connection to the Internet, the telecommunications operator in each office installs a router with a LAN and a WAN IP and configuration of these devices cannot be changed except the LAN IP. Only the central office network that is 192.168.0.0 have a router that has internet access. Remote offices have no access to the internet, what is needed is that remote offices can access the internet using ADSL router 192.168.0.254 at the central office. There are a small devices in each remote office that must connect to the internet and do not support any configuration except IP, mask and gateway, for example you cannot add a static route. Currently the pc's at remote offices has IP communication with the server from the central office using a static route. put some VPN routers between each LAN and the operator's routers (where RT yellow star appears in the diagram) and put the hosts of the two branch offices same IP range that the central office network? I had thought to use RSV400 routers?
View 6 Replies View RelatedI have a WRT54GX2 router and my laptop is connected wirelessly to the router. It worked fine before but now, the connection is only local, it's not connected to the internet.On the router, it says: Default Gateway: 0.0.0.0.I think that it should say 192.168.1.1 instead.I tried dhcp release and renew but it didn't work.The firmware version is 1.01.22.
View 3 Replies View RelatedI am currently using an E900 wireless router. The router is on the second story so I have to use a wireless router booster to enhance the signal strength. I have been using the booster for well over a month with no issues whatsoever; however, tonight I attempt to get onto World of Warcraft and I keep getting disconnected every 5 minutes. After I run the diagnostic it fixes the problem and says that the "default gateway not available". I tried restarting the router, restarting the booster, unplugging the wireless adapter, checked the firewall, and also restarted my computer.
View 2 Replies View Relatedabout two days ago my main PC lost the ability to connect to the internet. I'm useing a trendnet tew-687ga adapter and a netgear n600 router. I can't ping the default gatway 192.168.1.1
View 2 Replies View RelatedHow can I change default gateway and DNS's for L2TP type of connection? I've tried to specify them in static IP address first and then switched to L2TP as adviced in one forum, but it didn't work. I don't understand why such settings as Gateway and DNS servers cann't be specified as for PPTP connection. Firmware is 2.0.37.
View 1 Replies View RelatedLoss connection every day for several hours and just comes back. Reset router than works fine. Only about six months old. Found several forums staing the same problem. I have a RV016 16 port VPN router. What can I do?
View 1 Replies View RelatedWe have two MPLS circuits managed by two different suppliers, one carries VOICE the other DATAWe are to decommision the VOICE MPLS and have increased the bandwith of the DATA MPLS to carry VoIP traffic too.
At both of our sites A & B ,devices connected to the LAN have a default gateway of the VOICE providers Cisco 2600 router , which then goes into the LAN switching. (see diagram)So what I am trying to achieve is toto simply replace these 2600 routers from the VOICE MPLS provider with our own so we dont have to change the default gateways at both sites.
Testing
Our Cisco 2600 routes are plugged into each LAN switching environment with two subinterfaces configured, one for voip and the other for dataThe problem is from the router and respective subinterfaces we can get to the other sites destination without any issue, but if for example a user is at site A with Ip address 10.16.11.12/16 they cant ping the VOIP subnet at site B 10.3.11.0/24. But If a ping is issue from the Site A test router then the 10.3.11.0/24 subnet is reachable but only on the 10.3.12.0/24 configured subinterface.So i guess what Im saying is 10.16.0.0/16 from the LAN needs to be able to get to 10.3.11.0/24Note at site A 10.16.0.0/16 & 10.3.12.0/24 can communicate no problem and at site B 10.207.0.0/16 & 10.3.11.0/24 can communicate no problem.We are using IP routing, should we be using route-maps?
So network was running fine for about a year or so. Network consists of 1 Motorola SB6120 cable modem attached to a D-Link DIR-601 wireless router. All settings were default except for SSID and WPA password. One day I just couldn't access internet anymore. I've narrowed it down to the default gateway that is being given out through DHCP. The default gateway that is being given out is the IP of the modem (192.168.100.1) and not of the Router (192.168.0.1). I can't find any option on Wireless router to be able to force the gateway address when handing out the gateway IP. Theoretically I thought I should be able to put router on same subnet as modem as 192.168.100.2 but that still doesn't work. If I set the IP adresses statically on the PCs and give it the Gateway of the Router everything works fine. I should mention this is for my boss' house and basically I dont want him calling me everytime he has a friend come over and I have to talk em through setting up a Static IP.
And just for an example this is what I get if I use DHCP:
IP Address: 192.168.0.155
Mask: 255.255.255.0
DNS: 192.168.0.1
Default Gateway: 192.168.100.1
And If I want it to work I have to change the default gateway to 192.168.0.1 I've tried updating routers firmware and reset to factory default numerous times. Is it possible for a router DHCP stop working?
I'd like to add a WRT54g2 to my LAN. I'd like it to communicate with my existing LAN router, and not to talk directly to the LAN. Therefore, in Basic Setup, I don't have the top part (Internet Setup) configured. Is that a mistake?But, it seems that when I enable DHCP, it hands out its own IP as gateway, and then doesn't seem to send the traffic on upstream. When I configure clients manually with the real router IP, they work fine.
So, I'd like, I guess, Linksys to forward traffic on a static route to real router. How do I do this? Adding a route to real router yields the error, "maybe default route already exists."
I am using a WRT310N. I have a Cisco ASA5505 as my firewall and don't need the routing capabilities of the WRT310N. So I just plug the LAN port on the WRT310N directly to my LAN switch. I just need the WRT310N to have an IP address for management. So I configure the LAN with an IP address, but there is no way to set the default gateway on the LAN. You can only set the default gateway on the WAN interface, which I don't use, since I am using this in an AP only type of configuration.
View 1 Replies View RelatedI am using a RV016 (192.168.1.2) as a router and DHCP. It automatically assigns its own IP which is 192.168.1.2. I can not set my RV016 to assign a Default Gateway IP of the server. The workstations will connect to internet via this server (192.168.1.1)
View 1 Replies View RelatedWe were hit by hurricane Sandy a couple weeks ago and lost power for a week and a half. Now that our cable has been restored I noticed that the wireless internet wasn't working. The wired internet works fine to this computer but no Wi-fi.I think the problem is the routers default gateway. It's supposed to be 192.168.1.1 but right now it's 24.191.112.1 .So far I have tried:
-Powercycling everything
-ipconfig/ flush DNS
-ipconfig/ release and ipconfig/renew
-Checking all the wires are pugged in fine (They are).
I have my E1200 connected to my Netgear FVS318 router (which is a wired router) and the Netgear is connected to the internet.When a wireless client attempts to connect to the internet after automatically receiving an IP from the E1200, they do not have internet access as the default gateway that gets assigned is the IP of the E1200 192.168.2.100, which is not correct. It should be assigned 192.168.2.1, which is the IP of the Netgear router. Thefore, I have to manually set their IP addresses to use 192.168.2.1. How do you configure the E1200 to assign the correct Default Gateway IP to wireless clients who want to use DHCP?
View 4 Replies View RelatedWe have an ADSL connection and use a D-Link DSL-320B modem. We have a D-Link DIR-120 router connected to this modem. This has worked perfectly fine up until today when we disconnected the router and connected a computer (call it A) directly to the modem because it was getting an unusable connection through the router for some reason. We later also performed a factory reset on the DIR-120 router.
Unfortunately, after the above steps the router did not receive any IP address (through DHCP) from the ADSL connection anymore. During my attempts to debug this I noticed that my laptop (call it B) didn't get any IP address either (when connected directly to the modem). I noticed the following syslog entries repeating over and over while trying to connect: [code]
At this point computer A could still get a connection just fine tho (when connected directly to the modem).
I then tried to change the MAC address of the router to an arbitrary one (a copy of computer B's MAC address but with the last digit increased by one). The router still did not get assigned any IP address. Finally I tried making the router clone the MAC address of a third computer (call it C). C has never been connected directly to the modem. Doing this worked. After cloning the MAC address of computer C the router is immediately assigned an IP address and the internet connection works as it did prior to all this.
Now, my question is, why would computer B and the original MAC address of the router not be able to get an IP address while two other computers worked just fine? Why would changing to an arbitrary MAC address not work while cloning the MAC address of another computer did? Could the router's MAC address have been blocked by the ISP for some reason (and what could cause this)?
but my situation seems more like a blacklisting of some MAC addresses rather then allowing just a single MAC address.
I have COX cable so DHCP would be the right way. My D-Link 655 wireless router is set for DHCP. I have a choice between PPPoE or DHCP so I pick DHCP. My wireless laptop is trying to connect to the Internet using PPPoE and won't connect. It will connect using Ethernet. How can I get my laptop on the Internet because it shouldn't be using PPPoE for wirerless?
View 1 Replies View RelatedWhat is the default IP address for a Netopia 3347 router?
View 3 Replies View Relatedi joined because i keep on having the same problem. i read around the forum a bit before joining and i saw that mcafee was causing the problem for a lot of people. i dont have mcafee so that cant be it several crashes per day. like, literally close to 100 of them.
View 3 Replies View RelatedPeriodically, I drop internet everywhere around my college's campus. I'm literally four feet from a router, but it doesn't seem to matter. I'll disconnect, run troubleshooter, and I'll get the error message saying that the default gateway is not available. My college is designed for Macs, but I'm running Windows 7. My Mac colleagues do not experience problems. The computer works at home and at nearly every other wireless network I've brought it in range of. Specifically, either IBM or Dell.
Dell XPS 15
i7-2720QM
8gb Ram
Windows 7 Home Premium SP 1
540? Something around 500 Nvidia graphics card
Ipconfig results:
Windows IP Configuration
Host Name . . . . . . . . . . . . : George-PC
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
[code].....
I recently got a new laptop and ever since, the internet goes in and out. Most of the time it is not out long enough to display the no connectivity icon or stop music from streaming but it is noticeable. When I run the troubleshooter it says that the default gateway is unavailable. I tried manually setting the connection information but the same thing keeps happening except the troubleshooter then says that DHCP is not enabled. I've disabled every firewall I can find and updated all the drivers available. Here is my info:[CODE]
View 3 Replies View RelatedWhat is the default IP address of Buffalo Wi-Fi Router WHR-HP-G300N-AP? I just bought new one but I forgot that my PC CD-ROM is not anymore working. I'd like to set this up thru the default IP address.
View 1 Replies View Related