What is the default IP address of Buffalo Wi-Fi Router WHR-HP-G300N-AP? I just bought new one but I forgot that my PC CD-ROM is not anymore working. I'd like to set this up thru the default IP address.
View 1 Replies
I have the Air Station WHR-G300N. I just moved here from CA, I was on Verizon and now trying to use it on my girlfriend Cox system I can't get it to operate correctly.
Her PC system stopped having internet connection after about 2 weeks(running on the router) and going with Cox's reboot procedure of eliminating the router it can back up and seems to work fine as soon as I hook it back to the modem it stops.
I have unplugged all cables waited 30 seconds on both systems a couple of times. The lights are on the modem and the router.
I have a Buffalo WHR-G300N router & I am having probs with assigning a static address to a nas device.I have set up the static ip address i want to use in the nas When I look at the dhcp leases in the router, the device shows up as having an automatic assignment with a different ip address to the one set in the nas.If I manually assign the ip address which I want to use, or, if I edit the automatically assigned entry, the old one stays as an automatic assignment. This means that I then have 2 ip addresses for 1 mac address.When I try to access the nas, with only the automatically assigned address present in the router settings, I can still access it using the ip address I have manually assigned to the nas, even though the manual ip does not show in the router.How can I delete the automatically assigned dhcp lease & just keep my static one??
View 2 Replies View RelatedI have been trying from last 2 days to connect my Wireless USB Modem (from Telecom operator) to Buffalo's WHR-G300N V2 (Airstation Nfiniti High Power Gigabit Router, Access Point & Bridge) device and to connect to multiple devices using eithernet cable such PC and Vonage adaptor. I get internet connection from Telecom operators wireless USB Modem (which does not have ethernet port,, I use wireless to connect to my laptop), so I want to connect this telecom's USB modem to my Buffalo router which has multi ethernet ports. And use these ethernet ports to connect to my PC, Vonage and other wired devices. I am using Buffalo's WHR-G300N V2 (Airstation Nfiniti High Power Gigabit Router, Access Point & Bridge) to get internet from USB modem.
View 6 Replies View RelatedI just purchased a Buffalo WZR-600DHP router and have been having a weird issue. When using the router on the shipped DD-WRT firmware I consistently get "The default gateway is not available" error and I have to reset my wireless adapter on my laptop. This issue doesn't occur on my hardwired desktop or interestingly enough when the Buffalo router was switched to the "user-friendly" firmware the issue didn't occur either. Both times the router was on the DD-WRT firmware I've had the default gateway issue.
View 1 Replies View Relatedhrome threw me a DNS lookup failed. I go into my network settings and I noticed that I had limited connectivity. It would switch between no network access and no internet access every few seconds. After a bit of fiddling around, I got it to connect through assigning myself a static IP. This isn't exactly convenient because I use this computer on multiple networks. When I try to have it on automatic IP, I get no IP address or default gateway when I do an ipconfig /all. It would appear that my router quit assigning my laptop an IP for no reason whatsoever. DHCP is enabled on the router, and all other devices work fine. What could possibly be the problem here? I'm 99% sure it's not an IP conflict either. It's not being MAC filtered because I'm on the thing right now posting this through a static IP. It's not my A/V because it's worked great in the past. Perhaps I should also mention it occasionally says "unidentified network" instead of the SSID
View 8 Replies View RelatedI have set wifi password. but i can't see what the password is.
View 2 Replies View RelatedWhat is the default IP address for a Netopia 3347 router?
View 3 Replies View Relatedsince my network (static ip, cameras, and other boxes) is set up using 10.0.0.xx. How do I change the default ip address on the Linksys e3500 wifi router to 10.0.0.xx?
View 2 Replies View RelatedI have bought EA4500 router recently in preparations for the Singapore fibre broadband upgrade.
But for the time being I'm using it to connect to my current Linksys WAG200G ADSL Wireless Gateway.
Here's the issue I'm currently facing. I have set my EA4500 router default IP address to 192.168.1.10 to aviod conflicts with my gateway which is using 192.168.1.1. But everytime when I connect my router to the gateway, the router's default IP address changes to 10.179.159.126 or some other random IP address by itself whenever I try to change to back. However, I'm still able to surf the internet and stuffs with that current settings.
Is there something that I could do to prevent the IP address from changing by itself? And will the same thing happen again when I upgrade to fibre broadband?
My Motorola 850G router is several years old and working fine. However, my wi-fi connection is presently "unsecured" and I need some assistance as to how to go about setting up a secure network. My browser is not recognizing the router's default IP address.
View 1 Replies View RelatedI would like to know what ip addresses I should see in this table. Shouldn't my default gateway IP have the same mac address as my computer or router? There are 2 different ip address/mac addresses from different a ISP than mine. I have a cisco DPC3825..I suspect a someone is spoofing my DNS.
View 4 Replies View RelatedI'm using a new Buffalo router and wanting to use my old Buffalo router as repeater to extend the WiFi coverage at home.
View 1 Replies View Related I currently have a Buffalo WHR-HP-G54 running tomato firmware. I get roughly 4 or 5 bars around the entire house. Soon I will have to relocate the router to the basement.
Should I get a stronger 802.11N router or should I setup another buffalo router and use it as a repeater?
I have been trying to connect my webcam inside and outside my network. I had it working until I set up my buffalo router. I see my wireless webcam (1st floor) from my pc (2nd floor). I cannot connect through the internet outside of my network.
I have dyndns service which worked on my android and from pc at work. Now with the Buffalo router I cannot. It appears that DDNS is configured correctly on the Foscam and I have wireless configured on the router - it pics up the MAC address but only displays an * in SSID field that should be "Nursery".
If port forwarding is required, I have it set up, but not sure that is correct. I believe my Buffalo router is the N300 DD-WRT
I'm trying to change my username and password, but I don't know how. The manual is in Japanese, so I don't understand, what I need to do.
I have a wired router that seems to be on 192.168.1.1. When I installed the wireless router for the first time, I connected without cable, that may be the problem about the DHCP Server, but I don't know. Anyways, these IP don't work:
192.168.11.1
192.168.11.100
I don't get any access and therefore all my neighbors can use my connection right now. But the router itself works fine from the start.
I have a Buffalo WHR-G125 router which was given to me for free by my ISP for being a loyal client. At home I have a computer, a laptop and a netbook. The router is connected to the computer and I have no trouble accessing the Internet on all three of these devices. I can open pages, download etc.
However: However if I decide to host a server on some game, my friends cannot connect. After doing some research, I found out that certain ports are "closed" (whatever that means) and I need to open them in order for everything to start working again."
Anyway, I checked the infamous site "portforward.com" for instructions on how to open these ports. It was all fine and dandy, until the point where they stated I need to access my router settings page ("default gateway" or whatever, you'll have to excuse my ignorance). I entered "ipconfig" in cmd and it turns out my default gateway is 192.168.1.1. So I entered this in the URL bar of my browser and got a nasty surprise:
"404 Not Found The requested URL was not found"
I am truly stumped. The address is not accessible on neither the computer, nor the laptop or the netbook. I tried some automatic port forwarding software, but it didn't seem to do anything for me.
The only reason for this I can think of is that my ISP is probably blocking the router settings page for some reason (and how unfortunate, I can't even complain, because it's free, after all).
I tried asking on the official Buffalo forums and even tried asking for support and got pretty much the same message: "Try resetting. However, if it's flashed, you can't do anything.".
Not exactly sure what to do right now. My worries:
1.) I'm not even exactly sure how to reset the darn router
2.) I'm scared that reseting won't do a thing and even if it does, I'm not sure I'll be able to reconfigure the entire thing by myself and the worst case scenario, not having internet at all.
Is there any way to access the friggin router settings page?
DCS 5230L possible to record on buffalo router buit in NAS?No option to choose, only can see SD card but Not my NAS.
View 2 Replies View RelatedFor the past few months, I have been using a Buffalo drive (formatted as FAT) as a media server to function as my network drive for iTunes. Unfortunately, I have recently noted in the last 2-3 weeks that, when copying new files, the file size changes to zero bytes. I do not seem to have this problem when i plug the drive directly into my computer via USB, only when adding files over the network. I spoke to tech support, who said, based on the story in that files can be correctly transferred when directly connected, it appears to be a network problem.
I am running OS 10.8 with iTunes 11 (but also occurred with iTunes 10) and using version 1.0.04 on the E3000.
I WOULD LIKE TO KNOW THE DEFAULT IP ADDRESS OF MY SIEMENS GIGASET SE568 MODEM THROUGH THE COMP
View 1 Replies View RelatedMy ISP is changing out all the ADSL routers in our area and they have blocked the Default Gateway Address, so we can not access it via Web Browser. This is frustrating because they changed our Wi-Fi password, instead of just keeping what we had like an Einstein. They said they did it because of Hackers
View 2 Replies View RelatedI'm trying to configure a 3com 5500 switch with default ports for each vlan.The default ports are connected to IPS/IDS and do not have an IP address. I have a trunked esx host coming in and want to send traffic to specific ports based on vlan id - one port per vlan (10 total). Right now all I'm getting on the ips/ids is stp and arp traffic.
View 2 Replies View RelatedI am having problems logging into my wireless router. It was reset and the ssid has changed back to the default name with no security. my paradyne modem ip address in 192.168.1.1 and apparently with ipconfig the default gateway is also 192.168.1.1. The wireless router is not opening for me make changes i can only log into the modem.
View 2 Replies View RelatedClient is having 1 file server running small business windows server 2003. Server is not configured with domain, it is working only on workgroup. We have around 15 users who are using that server as file server only. Now my main question is do i need to configure DNS server in that server?we also have internet connection running (have problem in that also, will explain next time) with wireless router to connected with switch. So do I need to setup dns in server also or just put static ip (I prefer static then dhcp) & dns server from ip will be ok? If I put dns which I got from ISP, so will it create any problem with using those file from server?the second question is..
What IP address, Default gateway and dns address I should use for Server & also client pc.
router ip - 192.168.1.1
server ip - 192.168.1.10
Currently no DNS setupcurrent configuration - Server
IP - 192.168.1.10
subnet- 255.255.255.0
gateway - 192.168.1.1
dns - 213.42.20.20 (from ISP)
dns2 - xxx.xx.xx.xx (from ISP)current configuration - Client
IP - 192168.1.111(to 115)
subnet - 255.255.255.0
gateway - 192.168.1.1
dns 1 - 192.168.1.10 (File Server)
dns 2 - 213.42.20.20 (from ISP)
I would like to change the default ip address on my netopia 3347 frrom 192.168.1.whatever to 192.168.0.whatever
View 2 Replies View RelatedMy neighbour n myself are using a shared internet connection. The modem is situated in his house and I have connected to that modem using a LAN cable, which comes to my house. That LAN cable goes into my WiFi router (through which I use the internet connection). I use a Lap and my neighbour a Desktop, he's receiving a "IP address conflict error" in his system, due to which his internet connection is getting disrupted. If I don't use my Wifi router and connect directly through the LAN cable he does not face any problem. But I need my router back?
View 2 Replies View Relatedwhat my IP address, my subnet mask, and what my default gateway is. I have tried typing "ipconfig" into CMD but then I only got up 100 boxes saying "Permissionisconnected"
View 12 Replies View RelatedI can't print in my network printer using my Laptop (WIFI). I have check the default gateway of the desktop PC on which connected the printer and its different from my Laptop. Also I cant "SEE" this desktop PC on the LAN.
View 1 Replies View RelatedI am about to configure a brand new AIR-WLC2106-K9 V05 and didn't manage to find what is the deafult IP address configured on the device. I need it so I could start Web GUI management session.
View 4 Replies View RelatedI tried to configure my wifi router recently to secure my internet connection. I wanted to add a MAC adress filter, but I had to leave before I could enter them all. I thought that I wouldn't have to enter my own MAC adress since I'm directly connected to the router with a wire, but it looks like I should have entered my MAC adress, because now I can't get access to my router by typing the IP adress, as usual. I tried to reset it, but it doesn't work.
View 2 Replies View Relatedrecently, i have connected the internet to my PC with cable. Here the problem is , the packets are not receiving in the status bar of internet connection. I have checked in command prompt, the ip address is connecting properly but the default gateway ip address is showing "Request Timed Out" message.
View 1 Replies View RelatedI have a 3500 XL switch with the following default gate IP address that i need to clear from the switch but not quite shore how to remove it.
I've removed the customer original Ip for security reason as this is an open discussion forum and just replaced with 1.1.1.1
switch#show ru
Building configuration...
Current configuration:
!
[Code].....
I have the following zebra.conf on my router box "A":
hostname nuclear-router
password password
enable password password
interface eth0
ip address 192.168.2.1/24
multicast
[code]...
eth0 is connected to a switch and contains the 192.168.2.0/24 range, and A is connected to my WRT54GL "B" (with IP 192.168.1.1, containing 192.168.1.0/24 range, DHCP serves IPs above .100) wirelessly. B is connected directly to my DSL modem.
The problem is that when I specify the default route using the interface name, I can't connect to the internet from A or any hosts behind it - I'm always hit with a "no route to host" error. Name lookup and pinging any local host (even in a different range) or the DSL modem works fine - it's only when going beyond the modem that things stop working. However, when I use the IP of B as the gateway, it works fine. I noticed that route output on A when the default route was specified using the interface alone had only an asterisk in the gateway column. I was under the impression that these approaches should be identical in practice, so though I got it working, I'd like to know what I'm misunderstanding (and/or misconfiguring). Why didn't the default route work when specified using just the interface?
All routers and the modem too have RIP (version 2) enabled, and of course the password isn't really the word "password".
