Cisco WAN :: EHWIC-3G-HSPA+7 Not Supported In Vrf Setups?
May 8, 2012we set up a 1941 with c1900-universalk9-mz.SPA.151-4.M3.binand tried to bring up EHWIC-3G-HSPA+7 in the vrf. [code]
View 4 Replieswe set up a 1941 with c1900-universalk9-mz.SPA.151-4.M3.binand tried to bring up EHWIC-3G-HSPA+7 in the vrf. [code]
View 4 RepliesI need to make some perfomances (like up/down GRE tunnels) on Cisco ISR 2921 by sending SMS. It could be doing by using 3G modem like a Huawei and a server with some expect/SSH-scripts.
But ISR gen.2 has EHWIC-3G modules, which working with GSM networks and they can send/recieve SMS. I think, that it should be an EEM event or some another way to track comming SMS and process it by TCL-script — get a sender number, SMS body and make usefull perfomances on my router (up/down GRE tunnels in my case).
If I done this trick only by using an ISR router and EHWIC-3G module, it will be much more stable scheme in that we dont have extra components (server, modem) potentially may falls.
Unfortunately, there are too low information about configuring this modules (especially, SMS-part) and I dont find usefull for me.
How I configurate EHWIC-3G-HSPA+7 card on 2911.
View 3 Replies View RelatedI am having problems with these types of 3G cards(EHWIC-3G-HSPA+7) from Cisco.We are using them on ships where we have a SAT connection and the 3G connection. Fail over between the two connections are handled by an IP SLA echo and a track on the cellular interface, towards an public IP where we have configured a static route to via the Cellular interface.
Once configured the connection comes up fine, the VPN tunnels comes up and all is good.But after some time the connection dies, the track goes down because no data goes through.a sh cell 0/0/0 all however say that the profile is active.
why I can't use cisco ehwic-3g-hspa-u card in cisco 2800 series and 1841 series router?documentation said that it should work with that devices but when I installed it, it doesn't work even as device i can't see I am using cisco latest ios advance ent. 15.1(4)M4?
View 3 Replies View RelatedI have many HWIC-3G-HSPA cards as backup connections and I need to keep them up for monitoring purposes. Being a backup connection they get little interesting traffic for them to spring into life but they are the source interface for a tunnel interface (we use DMVPN). The interface still insists on going down. I have even added static routes to the DMVPN hubs over the cellular interface and they still go down. What command do I enter to always keep them up? I had originally used 'dialer idle-timeout 0' and then removed it altogether which the same results. Below is what I have now.
interface Cellular0/1/0 ip address negotiated ip nat outside ip virtual-reassembly in encapsulation ppp dialer in-band dialer string gsmscript dialer-group 1 async mode interactive ppp chap hostname //username// ppp chap password //password//
ppp ipcp dns request
access-list 1 permit anydialer-list 1 protocol ip list 1
line 0/1/0 exec-timeout 0 0 script dialer gsmscript modem InOut no exec transport input all transport output all rxspeed 7200000 txspeed 5760000
I've recently changed my DSL connection to HSPA because of low speed of DSL connection (2000).
Anyway, I need to build up 5 Ghz networking at home but there is no dual band HSPA modem router on the market. I need a router which supports DLNA/UPnP for NAS Server. So, I have couple of solutions...
1- I can purchase dual-band Asus RT-N66U and use HSPA/UMTS stick to use this router as main router. I can do this because RT-N66U supports sticks via USB.
2- I can connect my HSPA modem to a dual-band router via LAN and by changing IP adresses I can use dual-band router again as a main modem router. This can be no problem via WAN but my modem has no WAN connection. Is this possible via LAN?
Or do you have any other solution how I can get my 5 Ghz netwroking at home using HSPA connection.
I've been using hwic-3g-hspa with 1841 before but now I'm using 1921 and I'm always getting timed-out
View 1 Replies View RelatedI have found in my storage a device: PCEX-3G-HSPA (attached a photo of it)
And wanted to use it, but cant find any drivers for it. My OS is Windows 7 64bit. How to make this device to work under Win 7?
Within the space of a few days we've had 2 HWIC-3G-HSPA-G cards appear to fail on different router models. In each case the sh cell x/x/x hardware output is empty i.e no firmware version or other data provided and the radio status is off. Attempts to force the interface down using the test ....modem-power-cycle or radio-power off get the same error message that the modem is still in reset. Reloading the router does not clear this so we recently tried to update the firmware using the latest version off CCO. The upgrade using the microcode commands failed with an error of "unable to determine the modem state".
View 3 Replies View RelatedI have a Dell XPS L502x (Core i7, 6 GB RAM, 2GB NVIDIA graphic card, 750 GB HDD)My laptop does not have HSPA mini card
Is there a possibility to add a HSPA mini card
i have a dell mini 10 that had ubuntu but i put vista on it and after i did it my network controller wont install and i downloaded almost every driver dell had and one worked but i had the 39 error code, the driver that worked was DELL_WIRELESS-5530-HSPA-MINI_A06_R220877 but had 39 error code
View 1 Replies View RelatedI have an 1921 that I use for L2TPv3 tunnel connection with 2 sides. I need to add others 2 sides and I thought to add an EHWIC-4ESG on my router. Can I configure different xconnections with this module? I would like to configure my router as below: [code]
View 1 Replies View RelatedWe have Cisco 2811 router with Hwic-3g-HSPA card. When I configure the system everything was fine. Around two weeks 3g interface works, got IP address ,everyting was fine.Yesterday I check the sytem and I saw that cellular interface become reseting itself, without stoping.We have 2 g.shdls and one 3G connection on the same router. dialer 0 ansd dialer 1 for g.shdls, and dilaer 3 for 3G connection. [code]
View 1 Replies View RelatedAccording to specifications fo Cisco ISR G2 2911, it has got 4 EHWIC slots. But in [URL] appears that Cisco2911 supports only 2 HWIC-2FE or only 2 EHWIC-1GE-SFP-CU.
View 1 Replies View RelatedI have two EHWIC VA -DSL cards in a Cisco 2901.
I want each to connect to a separate ISP, one ISP for VOIP, one for Internet. I want to then have a VLAN for VOIP, a VLAN for DATA
I am using a Cisco 3925 router and attempting to install an EHWIC card with no luck. The card I am trying to install is EHWIC-D-8ESG.
I have powered down the router, inserted the card into the proper slot and my router doesn't seem to recognize the new card. Is there a command I need to enter to enable the card?
I am thinking about buying Dell 5550 module to my Latitude E6410. I know that for E6410 is designed 5540 module, but newer 5550 for E6420 has ability to use faster HSPA+ networks.
So my question is, any info on this combination of Latitude E6410 and Dell 5550 module?
I just got a brand new Cisco 2951 router that has built-in 3 gigabit interfaces cards. We want to add additonal 2 GE EHWIC-1GE-SFP-CU card to it. When it booted up and type show inventory, it did not detect the presence of the card. There was light on at the back of it. I have checked the compatibility on Cisco. The card is compatible with this router. Do we have to install the card with special instructions in order for the router to see it?
View 1 Replies View RelatedI am getting the following error message on a Cisco 2921 as a result of which has a there is 99 % CPU util. This router has the following cards installed and 4G WWAN EHWIC is running 15.1(4) M3 image.
EHWIC_CELL_MSG-1-EHWIC_ERROR_EVENTS: eHWIC Error Event: TxCLK PLL lost lock, HWIC slot 3
We're installing a 4G wireless card (EHWIC-4G-LTE-V) in our 2911 for the first time. Upon boot-up, the IOS doesn't recognize the card (the "show inv" command doesn't list it at all). Do I need to give a command or have a certain IOS version in order for it to be recognized?
View 1 Replies View Relatedif there is a MIB available for the EHWIC-4G-LTE-V card that would allow me to monitor the current RSSI level?
If I issue the command "show cell 0/1/0 radio" on my Cisco2911 router, I get the following info. I'd like to monitor the "Current RSSI" level in Solarwinds.
Router>show cell 0/1/0 radio
Radio power mode = ON
Current RSSI = -67 dBm
LTE Technology Preference = AUTO
LTE Technology Selected = LTE
see the message "%ESWGE_ERR-3-NIOSII_UP_FAIL: NIOSII fails on 0/3/0 ehwic slot" in 3925 ? we install a new module EHWIC-4ESG in 3925 with ios 15.2.2(T1). 3925 couldn't find the module but got error message above.
View 1 Replies View RelatedI have installed a EHWIC-4ESG card into my 2911 router running IOS Ver 15.1(4)M2. When I do a show diag, I can see the card, but I get the following line "Could not get card instance pa_bay=0 slot=0." Am I missing a step, do I have change something, is it not compatible (all that I have read, states that is)
View 3 Replies View RelatedAny configuration guide for EHWIC-4ESW card. Also the difference in configuration between EHWIC-4ESWG and HWIC-4ESW if any?
View 1 Replies View RelatedI am having trouble setting up a EHWIC-VA-DSL-A= card on my cisco 2811 running the following the following:c2800nm-adventerprosek9-mz.151-4.M2.bin and C2800NM_RM2.srec.124-13r.T11
My hardware supplier tells me its the right adsl card (have 1 existing working card not the same) but the card will not detect on the system to be configured.is this the right card? am I missing something?
We have the problem that MPLS labeled packets are not being processed on EHWIC-1GE-SFP-CU if L3PDU + Shim-Header exceeds 1500 bytes.When we move the config exactly to the on-board Interface Gi0/0 it works with put any problems. [code]
View 1 Replies View RelatedI have an 8 port Gigabit EHWIC in my Cisco 1921 router. A darn nice little switch module.
However, through my research, I am unable to find if I am able to change the way the NIC lights (green LEDs) on each port function. They basically just stay lit 100% non flashing when connected regardless of the port speed and duplex and ignore flashing for any activity.
Is there a deep layer command on these EHWIC cards to make them flash with activity like full standalone switches? Trust me when you have enough switch ports filled up it does make monitoring your networks health and activity by having the port led's respond to traffic flow. At least in my opinion.
Can I populate all 4 EHWIC slots in a Cisco 2911 router with VWIC3-4MFT-T1/E1 cards supporting clear channel T1 data traffic?Or do I need a higher performance router inthe 3900 series to do this?The data sheets lead me to the conclusion that I can but I just want to validate this.
View 6 Replies View RelatedCan you configure a Cisco 1941 to use an 8 port EHWic module and the 2 onboard GE ports in a single LAN?
I've discovered you can't have the on GE ports associated with a VLan, and I'm when I've previously researched for a solution, bridging was mentioned but I cannot seem to get it to work (or completely understand it)The reason I would like to use all 10 ports on for the LAN is becuase I have 10 devices I need to connect to the 1941?
If the "GLC-SX-MM" is offical supported on "SPA-5X1GE-V2" ?My customer tested it and it seems to work but now i need an offical statement In the data sheet there is no entry of the requested SFP. url...
View 3 Replies View RelatedI have a Cisco 7206VXR with NPE-400. The IOS version is 12.4(24)T3. I installed a SA-VAM in the router in slot 6 but getting the following on the console.
AP-Pune-RT#Feb 23 11:16:34.484: %PA-3-NOTSUPPORTED: PA in slot6 (Unknown (type 650)) is not supported on this chassisFeb 23 11:16:34.484: %PA-3-DEACTIVATED: port adapter in bay [6] powered off.Feb 23 11:16:34.584: %PA-2-PABRIDGE: Failed to config bridge for PA 6Feb 23 11:16:35.384: %PA-4-IMPROPER_REMOVAL: Improper removal for slot 6.Feb 23 11:16:35.384: %PA-3-DEACTIVATED: port adapter in bay [6] powered off.Feb 23 11:16:35.468: %CRYPTO-4-PKT_REPLAY_ERR: decrypt: replay check failed connection id=975, sequence number=677864
Is the SA-VAM not supported in the Router 7206VXR?
I have an issue with Cisco 3560V2-24-PS which it indicates not supported in DFM. I can see the device working properly when I do snmpwalk and snmv3 test and device credential test. In fact I can see chassis view of this device.
IP Address = 10.10.1.60
DNS Name = DISTRI_SW02
Device Status = Unknown
Device Type = N/A
Aliases = N/A
Containments = N/A
But in LMS 3.2 supported device it indicates as supported. Current version of the switch is 12.2(58)SE2 which is higher than the minimum requirement 12.2(50)SE1. I tried to downgrade/upgrade IOS and still no luck.
As per information in the creent DFM (see below), it is supposedly supported 59.1.3.6.1.4.1.9.1.1023Cisco Catalyst 3750V2-24PS SwitchDFMDeviceUpdates19.0 Below is the current version of the LMS modules;
Products Installed Showing 1-9 of 9 records Product Name Version With Patch Level Installed Date 1.Campus Manager5.2.110 Oct 2012, 13:11:57 GMT+08:002.CiscoView6.1.910 Oct 2012, 11:27:52 GMT+08:003.CiscoWorks Assistant1.2.010 Oct 2012, 11:27:52 GMT+08:004.CiscoWorks Common Services3.3.010 Oct 2012, 11:27:52 GMT+08:005.Device Fault Manager3.2.010 Oct 2012, 11:27:52 GMT+08:006.Integration Utility1.9.010 Oct 2012, 11:27:53 GMT+08:007.Internetwork Performance Monitor4.2.010 Oct 2012, 11:27:53 GMT+08:008.LMS Portal1.2.010 Oct 2012, 11:27:53 GMT+08:009.Resource Manager Essentials4.3.110 Oct 2012, 13:17:50 GMT+08:00
Also my current device update.Showing 1-9 of 9 records Product Name Device Type Count 1.Campus Manager02.CiscoWorks Common Services03.CiscoView7614.CiscoWorks Assistant05.Device Fault Manager9366.Internetwork Performance Monitor07.LMS Portal08.Integration Utility09.Resource Manager Essentials812 I already downloaded all the patches online and all device updates were also updated.