I have two EHWIC VA -DSL cards in a Cisco 2901.
I want each to connect to a separate ISP, one ISP for VOIP, one for Internet. I want to then have a VLAN for VOIP, a VLAN for DATA
Can you configure a Cisco 1941 to use an 8 port EHWic module and the 2 onboard GE ports in a single LAN?
I've discovered you can't have the on GE ports associated with a VLan, and I'm when I've previously researched for a solution, bridging was mentioned but I cannot seem to get it to work (or completely understand it)The reason I would like to use all 10 ports on for the LAN is becuase I have 10 devices I need to connect to the 1941?
why router going to shut down mode after 15 or 30 min? Here is the #show tech support command. find the attached document.
View 3 Replies View RelatedI want to configure a bsc network with a cisco 2901 router, but bstun commands are not enabled. I've already found a lot of tutorial about "How to configure bstun network" but none about how to enable it.
"show bstun", "show bsc", "bstun peer-name", etc. return "% Invalid input detected at '^' marker."
Here my "show version" :
Router#show version
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.1(4)M2, RE)
Technical Support: [URL]
Copyright (c) 1986-2011 by Cisco Systems, Inc.
[Code].....
I have WS-3750G-12S-E with me and would like to configure BGP on the same. whether it is advisable to configure BGP on 3750G or not.
View 10 Replies View RelatedWe are having problems configuring NAT on our Cisco 1921 Router. Below is the running config. The problem we're having is for example our FTP server 192.168.1.16, cannot be accessed from its outside IP address, which is NATed on the router. The server is verified to be up and running and when we do a show debug ip nat, we see the router is translating outside users attempting to access the ftp server to it's correct internal IP address.
View 3 Replies View RelatedIhave a 3560 w/multicast support and I'm trying to configure a simple environment. I have 2 ports configured, one for the multicast server and the other for the client. Each are on their own subnet, so I have an ip route between the two. My run config on both ports is:
ip multicast-routing distributed
interface fastethernet 0/3 & 0/4
ip pim version 2
ip pim sparse-dense-mode
I'm using vlc server /client configured to use 224.0.0.1 on my isolated network. I can see the mulitcast traffic going into the port, and I the client is sending reports, but I think the 3560 is dropping the packets, since I don't see them coming in the client port. Need to configure a simple multicast environment using 2 ports on a Cisco 3560.
I have an 1921 that I use for L2TPv3 tunnel connection with 2 sides. I need to add others 2 sides and I thought to add an EHWIC-4ESG on my router. Can I configure different xconnections with this module? I would like to configure my router as below: [code]
View 1 Replies View Relatedwe set up a 1941 with c1900-universalk9-mz.SPA.151-4.M3.binand tried to bring up EHWIC-3G-HSPA+7 in the vrf. [code]
View 4 Replies View RelatedAccording to specifications fo Cisco ISR G2 2911, it has got 4 EHWIC slots. But in [URL] appears that Cisco2911 supports only 2 HWIC-2FE or only 2 EHWIC-1GE-SFP-CU.
View 1 Replies View RelatedI need to make some perfomances (like up/down GRE tunnels) on Cisco ISR 2921 by sending SMS. It could be doing by using 3G modem like a Huawei and a server with some expect/SSH-scripts.
But ISR gen.2 has EHWIC-3G modules, which working with GSM networks and they can send/recieve SMS. I think, that it should be an EEM event or some another way to track comming SMS and process it by TCL-script — get a sender number, SMS body and make usefull perfomances on my router (up/down GRE tunnels in my case).
If I done this trick only by using an ISR router and EHWIC-3G module, it will be much more stable scheme in that we dont have extra components (server, modem) potentially may falls.
Unfortunately, there are too low information about configuring this modules (especially, SMS-part) and I dont find usefull for me.
I am using a Cisco 3925 router and attempting to install an EHWIC card with no luck. The card I am trying to install is EHWIC-D-8ESG.
I have powered down the router, inserted the card into the proper slot and my router doesn't seem to recognize the new card. Is there a command I need to enter to enable the card?
I just got a brand new Cisco 2951 router that has built-in 3 gigabit interfaces cards. We want to add additonal 2 GE EHWIC-1GE-SFP-CU card to it. When it booted up and type show inventory, it did not detect the presence of the card. There was light on at the back of it. I have checked the compatibility on Cisco. The card is compatible with this router. Do we have to install the card with special instructions in order for the router to see it?
View 1 Replies View RelatedI am getting the following error message on a Cisco 2921 as a result of which has a there is 99 % CPU util. This router has the following cards installed and 4G WWAN EHWIC is running 15.1(4) M3 image.
EHWIC_CELL_MSG-1-EHWIC_ERROR_EVENTS: eHWIC Error Event: TxCLK PLL lost lock, HWIC slot 3
We're installing a 4G wireless card (EHWIC-4G-LTE-V) in our 2911 for the first time. Upon boot-up, the IOS doesn't recognize the card (the "show inv" command doesn't list it at all). Do I need to give a command or have a certain IOS version in order for it to be recognized?
View 1 Replies View Relatedif there is a MIB available for the EHWIC-4G-LTE-V card that would allow me to monitor the current RSSI level?
If I issue the command "show cell 0/1/0 radio" on my Cisco2911 router, I get the following info. I'd like to monitor the "Current RSSI" level in Solarwinds.
Router>show cell 0/1/0 radio
Radio power mode = ON
Current RSSI = -67 dBm
LTE Technology Preference = AUTO
LTE Technology Selected = LTE
see the message "%ESWGE_ERR-3-NIOSII_UP_FAIL: NIOSII fails on 0/3/0 ehwic slot" in 3925 ? we install a new module EHWIC-4ESG in 3925 with ios 15.2.2(T1). 3925 couldn't find the module but got error message above.
View 1 Replies View RelatedI have installed a EHWIC-4ESG card into my 2911 router running IOS Ver 15.1(4)M2. When I do a show diag, I can see the card, but I get the following line "Could not get card instance pa_bay=0 slot=0." Am I missing a step, do I have change something, is it not compatible (all that I have read, states that is)
View 3 Replies View RelatedHow I configurate EHWIC-3G-HSPA+7 card on 2911.
View 3 Replies View RelatedI am having problems with these types of 3G cards(EHWIC-3G-HSPA+7) from Cisco.We are using them on ships where we have a SAT connection and the 3G connection. Fail over between the two connections are handled by an IP SLA echo and a track on the cellular interface, towards an public IP where we have configured a static route to via the Cellular interface.
Once configured the connection comes up fine, the VPN tunnels comes up and all is good.But after some time the connection dies, the track goes down because no data goes through.a sh cell 0/0/0 all however say that the profile is active.
Any configuration guide for EHWIC-4ESW card. Also the difference in configuration between EHWIC-4ESWG and HWIC-4ESW if any?
View 1 Replies View RelatedI am having trouble setting up a EHWIC-VA-DSL-A= card on my cisco 2811 running the following the following:c2800nm-adventerprosek9-mz.151-4.M2.bin and C2800NM_RM2.srec.124-13r.T11
My hardware supplier tells me its the right adsl card (have 1 existing working card not the same) but the card will not detect on the system to be configured.is this the right card? am I missing something?
We have the problem that MPLS labeled packets are not being processed on EHWIC-1GE-SFP-CU if L3PDU + Shim-Header exceeds 1500 bytes.When we move the config exactly to the on-board Interface Gi0/0 it works with put any problems. [code]
View 1 Replies View RelatedI have an 8 port Gigabit EHWIC in my Cisco 1921 router. A darn nice little switch module.
However, through my research, I am unable to find if I am able to change the way the NIC lights (green LEDs) on each port function. They basically just stay lit 100% non flashing when connected regardless of the port speed and duplex and ignore flashing for any activity.
Is there a deep layer command on these EHWIC cards to make them flash with activity like full standalone switches? Trust me when you have enough switch ports filled up it does make monitoring your networks health and activity by having the port led's respond to traffic flow. At least in my opinion.
Can I populate all 4 EHWIC slots in a Cisco 2911 router with VWIC3-4MFT-T1/E1 cards supporting clear channel T1 data traffic?Or do I need a higher performance router inthe 3900 series to do this?The data sheets lead me to the conclusion that I can but I just want to validate this.
View 6 Replies View Relatedwhy I can't use cisco ehwic-3g-hspa-u card in cisco 2800 series and 1841 series router?documentation said that it should work with that devices but when I installed it, it doesn't work even as device i can't see I am using cisco latest ios advance ent. 15.1(4)M4?
View 3 Replies View RelatedWhat ISO do I need to purchase to get Cisco IOS Firewall on a Cisco 2901 - is it just IP Base or do I need one of the Security IOSs?
View 1 Replies View RelatedI have a 1-Port 3rd Gen Multiflex Trunk Voice/WAN Int. Card - T1/E1 in a 2901 that I want to configure for data only (T1 connection to the Internet)I don't see any options in the IOS for using this thing as a serial interface (data), only options for configuring PRI/ISDN.
View 5 Replies View RelatedThe license has been installed onto the router. Here is the relevant out from the show license all:
License Store: Primary License StorageStoreIndex: 0 Feature: ipbasek9 Version: 1.0 License Type: Permanent License State: Active, In Use License Count: Non-Counted License Priority: MediumStoreIndex: 1 Feature: WAAS_Express Version: 1.0 License Type: Permanent License State: Active, Not in Use License Count: Non-Counted License Priority: Medium
WAAS license as it says that this is not in use, WAAS under the interface is not possible.
I am trying to come up with a config for implementing QoS over a 512 kbps WAN link that will traverse voice and data traffic for now. I am using a Cisco 2901 router with 15.1(3)T IOS on it. my config is below
class-map match-any DATA-PRIORITY match protocol citrix match protocol sshclass-map match-any VOICE-CONTROL match protocol skinny match protocol mgcp match protocol h323class-map match-any VOICE match protocol rtp audio class-map match-any ANY match any [ code]...
THE ISSUE IS : when i add in the service-policy output WAN- QOS- POLICY command , i get the error " insufficient bandwidth 256kbps for bandwidth guarantee (180)". if i take out the " bandwidth 512 " command out then i get no issues adding the above command on interface g0/1
I have a Cisco ASA and a 2901 Cisco Router connected via site-to-site VPN. The ASA can ping over the VPN to computers behind the router, but the router can not always ping to computers in the ASA network. When i ping from a computer in the IOS router's 10.100.36.0 network the requests times out most the time; although every few minutes, i will get about 10 pings back, then stops working again.
I uploaded their two configurations.
The ASAs public IP is 20.20.20.5 and local (inside) network of 10.101.36.0/24
The IOS routers public IP is 20.20.20.10
There are many internal networks, but 10.100.36.0/24 is the one with issues.
I try to make a gre tunnel with 2 cisco routers 2901, ping responds between tunnel ip's ends, but I don't have pings from the pc's inside the networks. [code]
View 7 Replies View RelatedHow do I disable fragmentation on a 2901 router? I want it to simply drop packets oversized packets.In my lab, I am trying to test various MTU issues. I'm trying to use a 2901 router to simulate the WAN equipment that my WAN provider would deploy in production. In production i'm expecting the WAN to only support an MTU of 1320 with no fragmentation at all.
View 2 Replies View Related