Cisco Infrastructure :: How To Enable BSTUN / STUN Commands On 2901 Router
Jan 19, 2012
I want to configure a bsc network with a cisco 2901 router, but bstun commands are not enabled. I've already found a lot of tutorial about "How to configure bstun network" but none about how to enable it.
"show bstun", "show bsc", "bstun peer-name", etc. return "% Invalid input detected at '^' marker."
Here my "show version" :
Router#show version
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.1(4)M2, RE)
Technical Support: [URL]
Copyright (c) 1986-2011 by Cisco Systems, Inc.
[Code].....
View 4 Replies
ADVERTISEMENT
Jan 13, 2013
I have just received a new cisco 2901 and started on its configuration. when I started configuring VPN tunnels, I saw that non of the crypto commands are available.
The router runs on iOS 15.1.From what I read, people refer that the router needs to past a license activation or something like that. When I run show verison - i do see "none" under most of the categories.
View 6 Replies
View Related
Jun 6, 2012
Are the IOS commands the same on a router and a ASA for these two topics....CBT Nuggets where I train has 553 videos for some of the new topics. I am preparing for 554 as it has more ASA focus and thats more interesting to me.
View 1 Replies
View Related
May 22, 2011
why router going to shut down mode after 15 or 30 min? Here is the #show tech support command. find the attached document.
View 3 Replies
View Related
Aug 2, 2011
I have got a cisco 887 router with ios CC880data-UniversalK9-M Version 15.0(1) M6. I am trying to enable sip alg and setup a class map for Stun nut the router does not support the command for stun.
View 3 Replies
View Related
Sep 13, 2012
I have two EHWIC VA -DSL cards in a Cisco 2901.
I want each to connect to a separate ISP, one ISP for VOIP, one for Internet. I want to then have a VLAN for VOIP, a VLAN for DATA
View 1 Replies
View Related
Feb 23, 2006
how to enable RSTP in the switch (Let's say in 2950 switch).
Or do you have RSTP running in now-a-days switches?
View 2 Replies
View Related
Apr 12, 2005
Is it possible to enable login by http (web interface) to catalyst 4006 switch with WS-C4006 Software, Version NmpSW: 6.3(5) ?
View 21 Replies
View Related
Sep 26, 2012
transport the serial0 and serial1 from a remote route to a local router at his local serial0 interface.The routing mechanism is very easy, it like a RS485, incoming data at the local router is trasmited to the remote serial0 and serial1. If some data income at the serial0 or serial1 at the remote, this data travel to the local an is printed into de local serial0 Remote Serial0 and Serial1 ends at the local Serial0. The local Serial0 starts and ends at the remote Serial0 and Serial1.Both serials are RS-232 (is a async-protocol group)The RS-232 protocol is UNADDRESSED The application is a back-up serial link.
My Config is:
LOCAL R236:
bstun peer-name 192.168.33.236
bstun protocol-group 10 async-generic
interface serial0
physical-layer async
[code]....
If i debug the BSTUN PACKET:
*Mar 7 02:31:18.182: %BSTUN-3-NOPEER: No peer configured to route frame with destination address 0 (bstun group 10)
At the Cisco IOS Software System Error Messages ARAP Error Messages Manual notes:
BSTUN-3-NOPEER: No peer configured to route frame with destination address
[chars] (bstun group [dec])
Explanation A BSTUN route has not been configured for the frame with a destination address.Recommended Action If this message appears while you are debugging BSTUN, it indicates that no specific BSTUN route has been configured for the frames being received with the device address listed in the packet debug trace. You may choose to configure a BSTUN route, or ignore this message.I know that the address must be content on the frames that income at the serial port interface, I mean the router fordward the frames if this have some BYTE and the start that indicate what is address of a remote device, so i guess that this routing mechanism use that byte to select the remote router.But If I set the address at the local and remote route, the router is not who must include his own address in the frame?If I set a point to point link, the only way if I want to transport more that 1 link,? for now the only way is set TWO groups and set one for first link ant the other for the second. (Serial0--Group1--Serial0 and Serial1--Group2--Serial1)The router do not let me set the same group ant the same route. where at the Serial interface i set the LOCAL ADDRESS for a BSTUN protocol?
View 3 Replies
View Related
Oct 15, 2012
I have created a baseline template to run compliancy checks, I understand that lines beginning with a + are mandatory and lines begining with a - should not be on the router. What I need to know is, is there a catch all for any other commands on the router config (startup or running) but not mentioned in the baseline? For example, lets say this is my baseline:
+ service timestamps debug datetime msec
+ service timestamps log datetime msec
+ service password-encryption
+ hostname [hostname]
The router comes back as compliant as it has all the above lines. However there is obviously more config on the router, but this doesn't show? So I know I can get commands that are in the baseline but not on the router; but what about the other way round - on the router but not on the baseline? Surely this exists - at the least from a security point of view, an attacker could well have configured the Dot11Radio int, however without entering the command with the minus prefix I can't tell? LMS 2.6
View 4 Replies
View Related
Mar 17, 2011
I have one router 1841 in which i configured PBR for internet traffic from LAN. I hv two ISPs few server are configured for ISP1 and few for ISP2.I planned to shift my existing setup at 2901 G2 router. when I am configuring the same config on this router so traffic is passing through only from one ISP not from other, if I troubleshoot so I see that the interface which is connected with ISP2 is not getting any input/output packet.
Config is here:
==========
interface FastEthernet0/0
description ****** ISP2 ******
ip address 203.xx.xx.110 255.255.255.248
[Code].......
View 1 Replies
View Related
Apr 18, 2011
I have a 2901 ISR G2 router, with IOS 15.0.1M3 , this router is not working with static NATing, I have tried to configure this router with one internet link and make few static translations with it. But this configuration is perfectly working with 1841 ISR router.
View 2 Replies
View Related
Feb 28, 2013
I'm trying to run the ISM-VPN-29 in a 2901 router. Cisco says that the SECK9 and HSECK9 licenses are needed to operate this ISM. However, they also say that the HSECK9 license is not available on the 2901. I'm running the SECK9 license but it's still not working.
This link, table 5 states that the HSECK9 feature license is for 2921 and 2951 only:[URL]This link states that it is a requirement to run the card, and also that the card works on the 2901:[URL]
I am running 15.3(1)T IOS.
View 3 Replies
View Related
Jun 16, 2012
I have an old 2621xm router in CCIE lab at home. Only a week ago I started having issue on 2 of them. The problem is on one of them when I go under interface configuration and I type "no shut" nothing happens. Interface stays in administratively down status and when I check running config "shutdown" is still under interface.
On the other one the same problem but only with "router rip" command. I configure my rip routing but then when I check running config there is no rip section and also RIP is not running under "show ip protocols rip".These routers are connected to 2511 AccesServer. So I thought the issue might be communication from AccessServer to these devices. I connected a console cable straight to them and still the same problem. Everything else is working on these devices.
View 10 Replies
View Related
Dec 24, 2012
how to install VIC3-2E/M in cisco router 2901 & what precaution should have to be taken.
View 2 Replies
View Related
Jul 1, 2012
I have a 2901 router and I would like to enable the following feature router mobile. [code] I used c2800nm-advipservicesk9-mz.151-3.T1.bin on a 2811 and this worked without any problem.Is there a possibility that there is some kind of license associated with this feature on a 2901?
View 1 Replies
View Related
Oct 2, 2011
I have a 2901K ISR router IOS Version 15.0(1r)M12 and I will be using this as a internet router, The WAN interface will get dynamic IP from the ISP, so I need to configure PPOE. I am referring the following link for setting up PPOE. [URL] However I am unable to define PPOE protocol as shown below
INTERNETRTR(config)#!!!!! Configure Router as PPPoE Client to the ISP
INTERNETRTR(config)#vpdn enable
INTERNETRTR(config)#vpdn-group 1
INTERNETRTR(config-vpdn)#request-dialin
INTERNETRTR(config-vpdn-req-in)#protocol ?
l2tp Use L2TP
INTERNETRTR(config-vpdn-req-in)#
Any link for setting up PPOE on 2901 series router.
View 1 Replies
View Related
Jul 5, 2011
I am attempting to configure a Cisco 2901 router using IOS 15 to properly perform NAT/PAT translation between LAN and the internet connection. I've configured DHCP pool for the local interface (GigabitEthernet0/1), which works properly. The WAN interface (GigabitEthernet0/0) is configured to obtain its own IP by DHCP from the ISP. I can work on the LAN computers and I can access the internet directly from the router (using, for example, telnet and router's ping commands). The problem is, NAT does not work properly and connection from the LAN interface does not reach the WAN interface.
View 1 Replies
View Related
Apr 15, 2013
Trying to setup a DMVPN on out existing equipment that is currently running all point to point vpn connections. basicly its not working. my best guess is something with the config is interfering but i'm not sure the remote router (881) is always comming back with MM_NO_STATE and the main router(2901) is either MM_NO_STATE or MM_SETUP.
I added the config for the 881, 2901 and a debug crypto isakmp and debug crypto ipsec from both routers. I have verified the Keys are correct and it is not blocking port 500. if i issue a sh crypto isakmp policy they are the same on both routers. if you need me to post anything else i will, one note i removed the configs that were part of the point to point tunnls on the 2901 router.
View 3 Replies
View Related
Feb 18, 2013
I have a client who would like to create a two VPN tunnels from one cisco 2901 router. One to the HQ and one to the DR. Is this possible?
View 4 Replies
View Related
Jun 11, 2013
There are no commands like route-map & ip sla monitor on my cisco 1841 router, its ios version is 12.4(T1). I have to configure load balancing and failover on this router but without these commands i cant do that.
View 3 Replies
View Related
Jan 9, 2011
I was attempting to setup our 7204 Cisco router to use RADIUS for authentication via the AAA commands. I must have messed up when configuring it as it comes up via TELNET asking for a username and password but doesn't take my AD credentials. How might I login to this router to fix the config? Do I need to do a password recover process?
One note, I didn't save the running-config to startup-config, so if I restart the router will it load the startup-config, thus overwriting the running-config that wasn't working?
View 2 Replies
View Related
Mar 24, 2013
When i enter configuration mode for ATM any DSL commands are not recognized. Believe i have the right IOS.
.ROM: System Bootstrap, Version 15.0(1r)M15, RELEASE SOFTWARE (fc1)System image file is "flash0:c2900-universalk9-mz.SPA.151-4.M4.bin"Last reload type: Normal Reloadversion 15.1service timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname Router!boot-start-markerboot-end-marker!!no aaa new-model!
[Code] .......
View 2 Replies
View Related
Feb 1, 2011
i have trouble to get the serial card (2nd genteration T1 card) on up/up state on a 2901 router. the SP guy who installed the rj48 at the demarc says it was tested good. For some reason, it is on up/down state no matter what i tried.
View 4 Replies
View Related
Jan 10, 2012
i need to know how many links i can using with load-balance on the same router ? i have router cisco 2901 , 3 providers , every provider having 4 links can i load balance between 12 links ? i am using static route
View 11 Replies
View Related
Dec 22, 2010
I have configured PBR on my 1800 series router, it is working perfect. Now I am changing my router from 1800 to 2901 router with the same config, so the PBR stop working and I am not getting hits in the second WAN interface. [code]
View 2 Replies
View Related
Sep 19, 2012
I am trying to configure a 2901 router to act as NTP server on my network.This set "ntp master" in the router.I have no possibility to access an NTP server on the Internet.Now I want to configure a Windows 2003 DC to update the time from the NTP Server (router 2901).In Windows 2003, the registry value "Ntp Server" may have to be IP addresses or FQDN? (In my case I put router_ip_address, 0x1) 0x1 = use this "SpecialPollInterval" to update the time? Where you can find that these actions mean "next action is 3"? In Event Log in Windows 2003 DC receipt Event ID 35:The time service is now synchronizing the system time with the time source ROUTER2901_IP (ntp.m | 0x1 | W2K3_SERVER_IP: 123 -> ROUTER2901_IP: 123).Configure "Special Poll Interval" in 10 seconds.But the time on the Windows Server 2003 DC continuous five minutes ahead of time compared to the 2901 router.
View 2 Replies
View Related
Feb 18, 2013
I need to break into a 2901 router to recover the passwords. Cisco's methodology for password recovery on 2900 seriews routerssays to remove the compact flash card and reboot into RMON. There is no external compact flash card on a 2901. Is there acompact flash card inside the box? Or can you use the older method of rebooting and then hitting ctl+break to boot into RMON?
View 5 Replies
View Related
Jul 6, 2011
I've been looking to see if its possible to create a GRE tunnel between a Cisco 2901 with 3 adsl WIC cards and a Cisco ASA.The Cisco 2901 is at our remote office and we have 3 adsl lines for resillience as they tend to go down alot.The Cisco ASA is at our Head Office sitting behind our ISP's managed router.
The desired end result would be to have three GRE tunnels, 1 for each DSL line terminating on the ASA at head office and use EIGRP routing protocol to move traffic across to another tunnel should one fail, and encapsulate all of that with IPSEC.
View 8 Replies
View Related
Jan 16, 2013
Router : cisco 2901 with securityk9 licence
I used this manual : [URL]
Im trying to change de login page but the command doesn't work : ip admission proxy http login page file disk1:login.htmThis is what I see when I type (config)#ip admission ?
absolute-timer Absolute Timeout in minutes
auth-proxy-audit Authentication Proxy Auditing
auth-proxy-banner Authentication Proxy Banner
[Code].....
View 1 Replies
View Related
May 2, 2012
i'm interested if it's possible to set the NTP server via DHCP on an 2901 Router with 15.2(2) image.
i configured the interface gigabit 0/0 as dhcp client. The DHCP Server sends to me DNS, Default GW and NTP. All is working fine, but the NTP will not be configured. i tried to add an DHCP option request, but there is no NTP (42) value. [code]
is there any way to add the value NTP (42) for the DHCP request or isnt it possible?
View 4 Replies
View Related
Dec 5, 2011
i want to use the cisco 2901 router with two adsl cards(EHWIC-VA-DSL-B) and would like to know if that possible without any restrictions with the ip base license.
View 2 Replies
View Related
Apr 10, 2012
I am using DHCP/TFTP to autoconfigure a 3945 router. The router properly obtains an IP address and finds the correct TFTP server. The issue lies in the download of the configuration file from the TFTP server. The router downloads the file, gives the "Ok" message, and prompts you to press Return to get started. When I view the running-config, several commands are missing from the Serial 0/0/0 section (HWIC-2T). If I modify the config file on the TFTP server to use Serial 0/0/1 instead and repeat the process, the configuration file loads without any issues and Serial 0/0/1 has all of the commands.
I also tried moving syntax around in my config file, but the end result is still the same. If I use Serial0/0/0 - I don't get all of the commands. If I use Serial 0/0/1, I do.
View 1 Replies
View Related
