Cisco WAN :: Create Two VPN Tunnels From 2901 Router?
Feb 18, 2013I have a client who would like to create a two VPN tunnels from one cisco 2901 router. One to the HQ and one to the DR. Is this possible?
View 4 Replies
ADVERTISEMENT
Cisco VPN :: Create Multiple IPsec Tunnels On 837 ADSL Router?
Nov 4, 2011I need to create multiple ip-sec vpn tunnels on A Cisco 837 ADSL Router. I am able to create one tunnel but the second connection is asking for the outside interface which is atm and already taken by the first tunnel. How can i create more tunnels?
Secondly, after creating the first tunnel i am able to access the remote lan network but when i tried tracert "remote lan ip of a pc" from my pc i got "request timed out" after passing my 837 but succeeded to reach the target. Does tracert needs something to be opened in the router?
Cisco WAN :: 2821 Router To Accept 2 Different Incoming WANs And Able To Create VPN Tunnels
Apr 1, 2013I am currently running a 2821 to terminate vpn links from all our branch offices over a WAN. I need to add a second interface in order to facilitate a move to a different WAN provider. seeing as the 2800 models are EOL I was looking for an upgrade. My local retailer wants to sell me the following:CISCO3925E-SEC/K9 IS Router 3925E security bundle SEC license pack,HWIC-2T 2 port serial WAN card,MEM-3900-1GU2GB Upgrade to 2GB 1,now my question is why can't i use the 2900 models in order to save some money?All I need is a router that will accept 2 different incoming WANs and the ability to create vpn tunnels over them..
View 19 Replies View RelatedCisco VPN :: 2901 VPN Tunnels Struggling To Start On Reload
Jun 10, 2013I've got my Cisco 2901 with Security license setup and running (seemlingly) great ... However, with one issue that's scaring me a little bit.After a reload or power-on, the router starts up and begins trying to negotiate the three VPN connections. All three connections are to SonicWALL routers (1 NSA-2400 and 2 TZ-100), and those are configured with "Keep Alive" enabled.The problem that I'm having is that the VPN connections do not come up. When I do a 'show crypt session', it shows all IKEv1 SA as DOWN-NEGOTIATING. It will stay this way indefinitely. The only thing I can do that works is to log into each respective SonicWALL, disable the particular VPN policy, then re-enable -- and then it works no problem.
The only thing I can think of that might be affecting the success would be the "Keep Alive" enabled on the SonicWALLs ... But at this point, I'd rather not disable that until I know more about what may be the cause. (Definitely can't take down a tunnel or play around during production hours for testing.) There is some random stuff in there too, as I was attempting to provide access for myself when remote through VPN. Here is my current running configuration. [Code]
Cisco VPN :: Create A Site To Site VPN Using 2901 And Linksys Router?
Mar 28, 2012I am trying to create a site to site VPN using a cisco 2901 and Linksys router.I have the VPN configured and connected and I can ping gateway to gateway. However, from the Cisco I can't ping any of the devices beyond the gateway.Example, from the cisco I can ping 192.168.5.254 (gateway IP address) source gig 0/1 and it works great.
However if I ping from the cisco 192.168.5.50 (end user PC) source gig 0/1 it doesn't work.I have created a client VPN and that works perfectly.Below is my config.
crypto isakmp policy 1
encr 3des
authentication pre-share
group 2
!
crypto isakmp policy 2
[code]....
Cisco VPN :: WRVS4400N - ASA Cannot Create Multiple Tunnels To Same Peer Address?
Jun 23, 2012We have several remote sites with Linksys WRVS4400N and Smoothwall firewall/vpn devices. I need these sites to be able to connect to multiple dis-contiguous subnets at our main office. This was easily done with smoothwall and linksys. You create a separate tunnel for each subnet and voila, you're done. However, when I tried this with our newly installed ASA, it will not let me create multiple tunnels to the same remote peer address. This is a problem since these sites only have a single static public IP address. Am i missing something or does the ASA not allow connections to/from multiple subnets form a site with a single peer address?
View 13 Replies View RelatedCisco :: ISRG2 2901 - How To Create Bulk Configuration Files From Template For Staging
Aug 17, 2011We have created a sample configuration for ISRG2 2901 Router. The sample configuration is long, and with copy/paste it is possible to skip some lines, and it is difficult to ensure the configuration of every device is standardized due to this error possibility. What we are trying to achieve is first create a template from this sample configuration file, and then create configuration files for each device seperately and automatically. After creating this configuration instances, we want to be able to distribute the configuration files (and possibly the ios) to the devices during the staging phase. Since there are about 1000 2901 routers, creating configuration files is important?
From searching we have found the following tools:
1) CCE (Cisco Configuration Engine): This tool seems to be very efficient for distributing the created configuration files. We may use the serial number of the device, and it provides almost zero touch provisioning of the configuration files to the devices. Creating the configuration file from the template seems to be manual, i.e enter the ip addresses of the interfaces, the routing tables one by one for each device. How can we use velocity template for device configs?
2) Ciscoworks LMS Prime: It is possible to create a baseline template for the devices, and after getting the backup configuration of the routers, it is possible to compare the actual configuration of the device with the baseline template, and understand if there is any difference with each other. This is indeed very useful in order to keep the configuration standardized, we again could not find a way to create bulk configuration files from the baseline template.
3) Solarwinds Config Generator: This tool is useful for creating a configuration file from a template, but again not for automatically creating configuration files, and needs manual intervention.
4) Excel Macro: It seems that some people have achived to automatically create configuration files with using an excel macro, but we could not find a procedure or tip of how to achieving this.
5) Pearl or TCL/TK Script: Again since we are not software developers but from networking field, it is difficult to achieve a working form of this scripts or codes due to to lack of documentation and development experience.
Cisco WAN :: GRE Tunnels On 2921 Router
Feb 20, 2013Is there a recommended number of GRE tunnels that Cisco 2921 ISR router with default configuration (512MB DDR2 ECC DRAM) can support?
View 5 Replies View RelatedCisco WAN :: PBR Is Not Functioning On 2901 G2 Router
Mar 17, 2011I have one router 1841 in which i configured PBR for internet traffic from LAN. I hv two ISPs few server are configured for ISP1 and few for ISP2.I planned to shift my existing setup at 2901 G2 router. when I am configuring the same config on this router so traffic is passing through only from one ISP not from other, if I troubleshoot so I see that the interface which is connected with ISP2 is not getting any input/output packet.
Config is here:
==========
interface FastEthernet0/0
description ****** ISP2 ******
ip address 203.xx.xx.110 255.255.255.248
[Code].......
Cisco WAN :: 2901 ISR G2 Router Static NAT
Apr 18, 2011I have a 2901 ISR G2 router, with IOS 15.0.1M3 , this router is not working with static NATing, I have tried to configure this router with one internet link and make few static translations with it. But this configuration is perfectly working with 1841 ISR router.
View 2 Replies View RelatedCisco WAN :: Running ISM-VPN-29 In 2901 Router?
Feb 28, 2013I'm trying to run the ISM-VPN-29 in a 2901 router. Cisco says that the SECK9 and HSECK9 licenses are needed to operate this ISM. However, they also say that the HSECK9 license is not available on the 2901. I'm running the SECK9 license but it's still not working.
This link, table 5 states that the HSECK9 feature license is for 2921 and 2951 only:[URL]This link states that it is a requirement to run the card, and also that the card works on the 2901:[URL]
I am running 15.3(1)T IOS.
Cisco :: How To Configure HQ Router To Allow Tunnels From Any IP Address
Nov 5, 2012My current set up is 1 HQ router (2911 ISR) and 8 site offices with a non-Cisco router.Each site has an IPSEC tunnel back to the HQ router.All of the site routers have a dynamic external IP address.This set up has worked ok for now, but I would like to look at moving to GRE tunnels so traffic from the sites can be routed to each over.I have read up on the configuration and I can set up an IPSEC GRE Tunnel in test labs using a static IP address on the spokes however I have not been able to find any documentation on how to configure the HQ router to allow the tunnels from any IP address.I did try setting the tunnel destination to 0.0.0.0 on the HQ side but this does not work.
View 5 Replies View RelatedCisco WAN :: How Many GRE Tunnels Can 7200 Router Support
Mar 1, 2011how many GRE tunnels (without IPSEC) can 7206 router supported. I have low bandwidth 2000 links & i want to configure GRE tunnels for them.
View 1 Replies View RelatedCisco :: 2911 Router - Netflow V5 Through GRE Tunnels
Aug 12, 2012Does the 2911 router support the ability for Netflow V5 to pass through GRE tunnels? I can't seem to find any documentation that indicates this.
View 2 Replies View RelatedCisco VPN :: Can Set Up Multiple VPN Tunnels On Router 800 Series
Apr 17, 2011I can set up multiple VPN tunnels on a cisco router 800 series?
View 9 Replies View RelatedCisco WAN :: Router 3945 Log To Get 100 Mbps As Sum Of Tunnels
Aug 9, 2011I am getting the following message from a 3945 router: %CERM-4-TX_BW_LIMIT: Maximum Tx Bandwidth limit of 85000 Kbps reached for Crypto functionality with securityk9 technology package license.
That router has 8 Gre/IPsec tunnels and one of those tunnels is 100Mbps.The question is, could I get 100Mbps as the sum of all tunnels, or is there a restriction to 85Mbps ??
Cisco WAN :: How To Install VIC3-2E / M In Router 2901
Dec 24, 2012how to install VIC3-2E/M in cisco router 2901 & what precaution should have to be taken.
View 2 Replies View RelatedCisco WAN :: 2901 Router Mobile Command
Jul 1, 2012I have a 2901 router and I would like to enable the following feature router mobile. [code] I used c2800nm-advipservicesk9-mz.151-3.T1.bin on a 2811 and this worked without any problem.Is there a possibility that there is some kind of license associated with this feature on a 2901?
View 1 Replies View RelatedCisco WAN :: Configure PPOE On 2901 Router?
Oct 2, 2011I have a 2901K ISR router IOS Version 15.0(1r)M12 and I will be using this as a internet router, The WAN interface will get dynamic IP from the ISP, so I need to configure PPOE. I am referring the following link for setting up PPOE. [URL] However I am unable to define PPOE protocol as shown below
INTERNETRTR(config)#!!!!! Configure Router as PPPoE Client to the ISP
INTERNETRTR(config)#vpdn enable
INTERNETRTR(config)#vpdn-group 1
INTERNETRTR(config-vpdn)#request-dialin
INTERNETRTR(config-vpdn-req-in)#protocol ?
l2tp Use L2TP
INTERNETRTR(config-vpdn-req-in)#
Any link for setting up PPOE on 2901 series router.
Cisco WAN :: 2901 - Configure Router Overload NAT (IOS 15)
Jul 5, 2011I am attempting to configure a Cisco 2901 router using IOS 15 to properly perform NAT/PAT translation between LAN and the internet connection. I've configured DHCP pool for the local interface (GigabitEthernet0/1), which works properly. The WAN interface (GigabitEthernet0/0) is configured to obtain its own IP by DHCP from the ISP. I can work on the LAN computers and I can access the internet directly from the router (using, for example, telnet and router's ping commands). The problem is, NAT does not work properly and connection from the LAN interface does not reach the WAN interface.
View 1 Replies View RelatedCisco VPN :: 2901 Router - DMVPN Is Not Working
Apr 15, 2013Trying to setup a DMVPN on out existing equipment that is currently running all point to point vpn connections. basicly its not working. my best guess is something with the config is interfering but i'm not sure the remote router (881) is always comming back with MM_NO_STATE and the main router(2901) is either MM_NO_STATE or MM_SETUP.
I added the config for the 881, 2901 and a debug crypto isakmp and debug crypto ipsec from both routers. I have verified the Keys are correct and it is not blocking port 500. if i issue a sh crypto isakmp policy they are the same on both routers. if you need me to post anything else i will, one note i removed the configs that were part of the point to point tunnls on the 2901 router.
Cisco WAN :: 2901 Router Crypto Commands
Jan 13, 2013I have just received a new cisco 2901 and started on its configuration. when I started configuring VPN tunnels, I saw that non of the crypto commands are available.
The router runs on iOS 15.1.From what I read, people refer that the router needs to past a license activation or something like that. When I run show verison - i do see "none" under most of the categories.
Cisco VPN :: 1921 Router Q - How Many IPsec Tunnels Will It Support
Nov 8, 2011I need to know how many IPsec VPN tunnels one Cisco1921 can support reliably. Haven't had any luck sifting through documentation on the web.
View 2 Replies View RelatedCisco VPN :: Configuring Multiple VPN Tunnels On 1721 Router
Jan 10, 2012I am in the process of configuring two vpn tunnels on one interface of cisco router series 1721. Any link or document with more information?
View 5 Replies View RelatedCisco WAN :: How Many Numbers Of GRE Tunnels Are Supported On 3925 Router
Apr 29, 2013How many numbers of GRE Tunnels are supported on Cisco 3925 router?
View 2 Replies View RelatedCisco VPN :: How Many Numbers Of GRE Tunnels Are Supported On 3925 Router
Apr 28, 2013How many numbers of GRE Tunnels are supported on Cisco 3925 router?
View 1 Replies View RelatedCisco WAN :: Rj48 How To Configure T1 Controller On 2901 Router
Feb 1, 2011i have trouble to get the serial card (2nd genteration T1 card) on up/up state on a 2901 router. the SP guy who installed the rj48 at the demarc says it was tested good. For some reason, it is on up/down state no matter what i tried.
View 4 Replies View RelatedCisco WAN :: 2901 Router Support For Load Balance
Jan 10, 2012i need to know how many links i can using with load-balance on the same router ? i have router cisco 2901 , 3 providers , every provider having 4 links can i load balance between 12 links ? i am using static route
View 11 Replies View RelatedCisco Infrastructure :: Router 2901 Shutdown After 30 Or 50 Minutes
May 22, 2011why router going to shut down mode after 15 or 30 min? Here is the #show tech support command. find the attached document.
View 3 Replies View RelatedCisco WAN :: Changing Router From 1800 To 2901 With Same Config
Dec 22, 2010I have configured PBR on my 1800 series router, it is working perfect. Now I am changing my router from 1800 to 2901 router with the same config, so the PBR stop working and I am not getting hits in the second WAN interface. [code]
View 2 Replies View RelatedCisco WAN :: 3845 Creating GRE Tunnels On Glbp Enabled Router
Jul 18, 2012Which is the best way of creating GRE Tunnels on a GLBP enabled router? I actually have two 3845 with GLBP configured as our gateway routers, and need to create gre tunnels to branches.The plan is to use the GLBP virtual IP as the Tunnel Source address and the branch WAN interface as the tunnel Destination address, how do i handle the Tunnel IP address? Do i create the same Tunnel on both gateway routers and have a glbp virtual IP address for the Tunnel Interface as well?
View 4 Replies View RelatedCisco :: Router 2901 As NTP Server For Windows 2003 Network
Sep 19, 2012I am trying to configure a 2901 router to act as NTP server on my network.This set "ntp master" in the router.I have no possibility to access an NTP server on the Internet.Now I want to configure a Windows 2003 DC to update the time from the NTP Server (router 2901).In Windows 2003, the registry value "Ntp Server" may have to be IP addresses or FQDN? (In my case I put router_ip_address, 0x1) 0x1 = use this "SpecialPollInterval" to update the time? Where you can find that these actions mean "next action is 3"? In Event Log in Windows 2003 DC receipt Event ID 35:The time service is now synchronizing the system time with the time source ROUTER2901_IP (ntp.m | 0x1 | W2K3_SERVER_IP: 123 -> ROUTER2901_IP: 123).Configure "Special Poll Interval" in 10 seconds.But the time on the Windows Server 2003 DC continuous five minutes ahead of time compared to the 2901 router.
View 2 Replies View RelatedCisco Switching/Routing :: 2901 Router Password Recovery
Feb 18, 2013I need to break into a 2901 router to recover the passwords. Cisco's methodology for password recovery on 2900 seriews routerssays to remove the compact flash card and reboot into RMON. There is no external compact flash card on a 2901. Is there acompact flash card inside the box? Or can you use the older method of rebooting and then hitting ctl+break to boot into RMON?
View 5 Replies View Related