Cisco WAN :: PBR Is Not Functioning On 2901 G2 Router
Mar 17, 2011
I have one router 1841 in which i configured PBR for internet traffic from LAN. I hv two ISPs few server are configured for ISP1 and few for ISP2.I planned to shift my existing setup at 2901 G2 router. when I am configuring the same config on this router so traffic is passing through only from one ISP not from other, if I troubleshoot so I see that the interface which is connected with ISP2 is not getting any input/output packet.
Config is here:
==========
interface FastEthernet0/0
description ****** ISP2 ******
ip address 203.xx.xx.110 255.255.255.248
My router was not functioning well so I decided it might be a good idea to reinstall the driver package via the admin upgrade page. Since then it doesn't work at all. The power light flashes constantly now.
what should to do if ever or incase something happen during flashing firmware.like power turn off, or you quit the installation, or wrong .bin file.what i did is upgrade the firmware dlink dir 615 3.03 ww c2 to ddwrt factory.bin but before that i have save the original .bin from 192.168.1.1 for incase restore original setting.i did not follow the instruction that get latest firmware from dlink but what i did is restore or use emergency to reback the 3.03 ww c2 .bin from my dlink that i was save from original setting. and it didnt work out it failed the router totally stopped working and functioning. only the dlink name light is on. even the reset button dont work or dont blink.what should we do for this kind of fault is there another way to return the setting back? no ethernet and wifi so no way of communicating with router. the router ethernet and wifi has stopped working. but the computer homw network is detecting the router whenever i plug it in computer through Ethernet but the local area network when plug to router is disconnected. the router wifi is not blinking either.
I have a 2901 ISR G2 router, with IOS 15.0.1M3 , this router is not working with static NATing, I have tried to configure this router with one internet link and make few static translations with it. But this configuration is perfectly working with 1841 ISR router.
I'm trying to run the ISM-VPN-29 in a 2901 router. Cisco says that the SECK9 and HSECK9 licenses are needed to operate this ISM. However, they also say that the HSECK9 license is not available on the 2901. I'm running the SECK9 license but it's still not working.
This link, table 5 states that the HSECK9 feature license is for 2921 and 2951 only:[URL]This link states that it is a requirement to run the card, and also that the card works on the 2901:[URL]
I have a 2901 router and I would like to enable the following feature router mobile. [code] I used c2800nm-advipservicesk9-mz.151-3.T1.bin on a 2811 and this worked without any problem.Is there a possibility that there is some kind of license associated with this feature on a 2901?
I have a 2901K ISR router IOS Version 15.0(1r)M12 and I will be using this as a internet router, The WAN interface will get dynamic IP from the ISP, so I need to configure PPOE. I am referring the following link for setting up PPOE. [URL] However I am unable to define PPOE protocol as shown below
INTERNETRTR(config)#!!!!! Configure Router as PPPoE Client to the ISP INTERNETRTR(config)#vpdn enable INTERNETRTR(config)#vpdn-group 1 INTERNETRTR(config-vpdn)#request-dialin INTERNETRTR(config-vpdn-req-in)#protocol ? l2tp Use L2TP INTERNETRTR(config-vpdn-req-in)#
Any link for setting up PPOE on 2901 series router.
I am attempting to configure a Cisco 2901 router using IOS 15 to properly perform NAT/PAT translation between LAN and the internet connection. I've configured DHCP pool for the local interface (GigabitEthernet0/1), which works properly. The WAN interface (GigabitEthernet0/0) is configured to obtain its own IP by DHCP from the ISP. I can work on the LAN computers and I can access the internet directly from the router (using, for example, telnet and router's ping commands). The problem is, NAT does not work properly and connection from the LAN interface does not reach the WAN interface.
Trying to setup a DMVPN on out existing equipment that is currently running all point to point vpn connections. basicly its not working. my best guess is something with the config is interfering but i'm not sure the remote router (881) is always comming back with MM_NO_STATE and the main router(2901) is either MM_NO_STATE or MM_SETUP.
I added the config for the 881, 2901 and a debug crypto isakmp and debug crypto ipsec from both routers. I have verified the Keys are correct and it is not blocking port 500. if i issue a sh crypto isakmp policy they are the same on both routers. if you need me to post anything else i will, one note i removed the configs that were part of the point to point tunnls on the 2901 router.
I have just received a new cisco 2901 and started on its configuration. when I started configuring VPN tunnels, I saw that non of the crypto commands are available.
The router runs on iOS 15.1.From what I read, people refer that the router needs to past a license activation or something like that. When I run show verison - i do see "none" under most of the categories.
i have trouble to get the serial card (2nd genteration T1 card) on up/up state on a 2901 router. the SP guy who installed the rj48 at the demarc says it was tested good. For some reason, it is on up/down state no matter what i tried.
i need to know how many links i can using with load-balance on the same router ? i have router cisco 2901 , 3 providers , every provider having 4 links can i load balance between 12 links ? i am using static route
I have configured PBR on my 1800 series router, it is working perfect. Now I am changing my router from 1800 to 2901 router with the same config, so the PBR stop working and I am not getting hits in the second WAN interface. [code]
I've recently bought a new PC (I7) to replace my old one. My main task was to get most of my files across and set up my new PC as the main computer on the home network. Currently my machine has a printer connected to it which I wish to share with all on the network. I've attached a screen cap of the network as displayed by my modem/router. 2 computers (my PC's) connect via ethernet and the other 2 laptops wirelessly. All computers (except my old PC) run Windows 7 - the old PC runs Win XP SP3.
What I can do so far is transfer files from my old to new PC. Each computer on the network (except the XP machine) can see each other but cannot access each other and despite network discovery + file and printer sharing on, cannot see the printer across the network. I've been doing a bit of research to try and solve my problems but am only getting so far. If there is a resource you could point me to that would be great as I'd like to develop a good understanding of how to manage the network.Here's is an IPCONFIG report on my main machine:
I bought a pix 515 to play with and i upgraded it to the farthest release 8.0(4) it was at 7.22 and the web interface and ASDM is not working. do i need to upgrade the ASDM? when i run the launcher i get a fatal error :
handshake_failure.
I just updated the IOS, did i need to save certain things? activation key's maybe???
We currently run 7206 routers with VAM cards and are able to configure the devices to perform stateful failover of tunnels from router to router. When moving to the 7604 with 15.1 IOS there are not any examples of how to set up the stateful failover of the tunnels between devices. We have the devices in the SSO mode are not able to understand how to get the redundancy between the devices functioning.
I am trying to configure a 2901 router to act as NTP server on my network.This set "ntp master" in the router.I have no possibility to access an NTP server on the Internet.Now I want to configure a Windows 2003 DC to update the time from the NTP Server (router 2901).In Windows 2003, the registry value "Ntp Server" may have to be IP addresses or FQDN? (In my case I put router_ip_address, 0x1) 0x1 = use this "SpecialPollInterval" to update the time? Where you can find that these actions mean "next action is 3"? In Event Log in Windows 2003 DC receipt Event ID 35:The time service is now synchronizing the system time with the time source ROUTER2901_IP (ntp.m | 0x1 | W2K3_SERVER_IP: 123 -> ROUTER2901_IP: 123).Configure "Special Poll Interval" in 10 seconds.But the time on the Windows Server 2003 DC continuous five minutes ahead of time compared to the 2901 router.
I need to break into a 2901 router to recover the passwords. Cisco's methodology for password recovery on 2900 seriews routerssays to remove the compact flash card and reboot into RMON. There is no external compact flash card on a 2901. Is there acompact flash card inside the box? Or can you use the older method of rebooting and then hitting ctl+break to boot into RMON?
I've been looking to see if its possible to create a GRE tunnel between a Cisco 2901 with 3 adsl WIC cards and a Cisco ASA.The Cisco 2901 is at our remote office and we have 3 adsl lines for resillience as they tend to go down alot.The Cisco ASA is at our Head Office sitting behind our ISP's managed router.
The desired end result would be to have three GRE tunnels, 1 for each DSL line terminating on the ASA at head office and use EIGRP routing protocol to move traffic across to another tunnel should one fail, and encapsulate all of that with IPSEC.
Im trying to change de login page but the command doesn't work : ip admission proxy http login page file disk1:login.htmThis is what I see when I type (config)#ip admission ?
i'm interested if it's possible to set the NTP server via DHCP on an 2901 Router with 15.2(2) image.
i configured the interface gigabit 0/0 as dhcp client. The DHCP Server sends to me DNS, Default GW and NTP. All is working fine, but the NTP will not be configured. i tried to add an DHCP option request, but there is no NTP (42) value. [code]
is there any way to add the value NTP (42) for the DHCP request or isnt it possible?
i want to use the cisco 2901 router with two adsl cards(EHWIC-VA-DSL-B) and would like to know if that possible without any restrictions with the ip base license.
I have an ASUS M4A785-M MB with an on-board LAN and all of a sudden stopped working yesterday. I have it connected to a 4-port D-Link network switch which has one other computer connected, and the switch is hard-wired to my wireless router.
Here are the trouble-shooting steps I've tried:
- uninstalling/re-installing the driver - tried using different wires. - by-passed the switch - used the wired connection with the other computer - tested the wire for my troubled computer on the other computer and it works fine - pinged the loop-back IP address (127.0.0.1) and it tested ok - bought a new NIC and still no connection
When I go to Network and Sharing Center, it shows my Home GRoup but then has the bid red X from the Home Group to the Internet.
The D-link dir-615 is not working.The modem is working perfect, because its the internet that im using right now (its connected directly to my laptop, so i know its the router for sure) But i want to make the internet on my modem wireless, but the D-link router has the orange globe light turned on (as im typing it still has the light on) and i just dont know whats wrong with it. I have already tried reseting it like 2 times, and it still doesn't work. When i connect my router, all it does is acquire the network address, and it just stays there, so no ip address will be detected... I might just buy a lynksys router, d-link sucks. This router was bought years ago by the way. It hasn't been used since like now.
It isnt the computer, i tried disabling the firewall, and reconnecting, but it just stays in 'renewing ip address' (the same things happen with all of the other computers that try to connect to it in my home) I click on the wireless icon and then on 'support' and next to IP Address it says "Invalid Ip Address"... The globe still remains orange on the router..
My Dlink DCS-942Ls had been updated to the latest firmware both 1.12.1608WW and 1.12.1628EU. (I grouped them into two firmware devices). They are all H/W version A1, agent version 2.0.15-b11. If I setup time to automatic time configuration and sync with NTP servers ( all from drop down list and Thailand NTP server time1.nimt.or.th) , they did not work and I must set time manually every times I power off and on these IP cameras. I knew that this issues has been raised for long times and still exist in the current firmware.Simple way to eliminate this problem is specifying NTP server into IP number. ping your national NTP server URL and then get the IP address , e.g. time1.nimt.or.th has IP 203.185.69.60 , or ntp1.dlink.com has IP 61.67.210.241. I have tested many ways and the results can be comfirmed that URL NTP letter cannot sync time but IP number can do. I also has a DAP-1360 Repeater mode and test with its "System Check" ping test, the result are success either URL NTP server name and IP number. NTP protocol is different to ping test. I'm not sure that which parties (ISP, DNS, Router, IP camera device) should fix this error. I decided to specify NTP server with IP number to all network devices from D-Link. Minor risk may occur if a national NTP server change its IP number.
I want to configure a bsc network with a cisco 2901 router, but bstun commands are not enabled. I've already found a lot of tutorial about "How to configure bstun network" but none about how to enable it.
"show bstun", "show bsc", "bstun peer-name", etc. return "% Invalid input detected at '^' marker."
Here my "show version" :
Router#show version Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.1(4)M2, RE) Technical Support: [URL] Copyright (c) 1986-2011 by Cisco Systems, Inc.
I recently removed trojan horse and malware using AVG. This was successfu,l but when I rebooted the machine it will not recognise any network connections, sound etc or operated software such as excel.ll the devices appear to be installed but won't work. When I try to open Intel it shows a message 'No supported wireless adapters available in the system'.
I have a Dell Inspiron n5010. Earlier bluetooth was functioned properly. But today bluetooth icon is not displayed on the tray. could not find my bluetooth devices while searching also not able connect from my my Bluetooth device. I have updated the driver from Device Manager.
I'm having a problem with my onboard NVIDIA nForce Network Ethernet card. I have a XPS 730 running Windows 8 (64 bit). What is the most recent date of the driver for this adapter? I was attacked by a VERY bad virus (called SMALL) and have just got everything back to normal (I think). It may be possible that the driver for my network card is corrupted. Device Manager says driver is dated 2/23/2012 and the version is 7.3.1.7336. Is this correct? Two weeks ago the machine ran fine, Windows 8 installed without a problem.
