I have a 2901 router and I would like to enable the following feature router mobile. [code] I used c2800nm-advipservicesk9-mz.151-3.T1.bin on a 2811 and this worked without any problem.Is there a possibility that there is some kind of license associated with this feature on a 2901?
View 1 RepliesI have recently bought cisco 2901 in order to replace it with our 1811W that we have at the moment.When I try to set a failover / backup with rtr; it seems like the function is not valid.Once I select rtr and set the object #, the reachability command is not available.Does that mean this function is not a part from the license package I have?
View 6 Replies View RelatedI have one router 1841 in which i configured PBR for internet traffic from LAN. I hv two ISPs few server are configured for ISP1 and few for ISP2.I planned to shift my existing setup at 2901 G2 router. when I am configuring the same config on this router so traffic is passing through only from one ISP not from other, if I troubleshoot so I see that the interface which is connected with ISP2 is not getting any input/output packet.
Config is here:
==========
interface FastEthernet0/0
description ****** ISP2 ******
ip address 203.xx.xx.110 255.255.255.248
[Code].......
I have a 2901 ISR G2 router, with IOS 15.0.1M3 , this router is not working with static NATing, I have tried to configure this router with one internet link and make few static translations with it. But this configuration is perfectly working with 1841 ISR router.
View 2 Replies View RelatedI'm trying to run the ISM-VPN-29 in a 2901 router. Cisco says that the SECK9 and HSECK9 licenses are needed to operate this ISM. However, they also say that the HSECK9 license is not available on the 2901. I'm running the SECK9 license but it's still not working.
This link, table 5 states that the HSECK9 feature license is for 2921 and 2951 only:[URL]This link states that it is a requirement to run the card, and also that the card works on the 2901:[URL]
I am running 15.3(1)T IOS.
I need to change providers from Verizon to AT&T. This modem came with the AT&T Sim card installed in my notebook. The software (Dell Mobile Broadband Utility Help) says " Choose Network Selection from the Settings Menu. Select AT&T and click Load." Unfortunately, Network selection is not an option.
How do I do it? This modem is compatible with Verizon, AT&T and Sprint networks.
how to install VIC3-2E/M in cisco router 2901 & what precaution should have to be taken.
View 2 Replies View RelatedI have a 2901K ISR router IOS Version 15.0(1r)M12 and I will be using this as a internet router, The WAN interface will get dynamic IP from the ISP, so I need to configure PPOE. I am referring the following link for setting up PPOE. [URL] However I am unable to define PPOE protocol as shown below
INTERNETRTR(config)#!!!!! Configure Router as PPPoE Client to the ISP
INTERNETRTR(config)#vpdn enable
INTERNETRTR(config)#vpdn-group 1
INTERNETRTR(config-vpdn)#request-dialin
INTERNETRTR(config-vpdn-req-in)#protocol ?
l2tp Use L2TP
INTERNETRTR(config-vpdn-req-in)#
Any link for setting up PPOE on 2901 series router.
I am attempting to configure a Cisco 2901 router using IOS 15 to properly perform NAT/PAT translation between LAN and the internet connection. I've configured DHCP pool for the local interface (GigabitEthernet0/1), which works properly. The WAN interface (GigabitEthernet0/0) is configured to obtain its own IP by DHCP from the ISP. I can work on the LAN computers and I can access the internet directly from the router (using, for example, telnet and router's ping commands). The problem is, NAT does not work properly and connection from the LAN interface does not reach the WAN interface.
View 1 Replies View RelatedTrying to setup a DMVPN on out existing equipment that is currently running all point to point vpn connections. basicly its not working. my best guess is something with the config is interfering but i'm not sure the remote router (881) is always comming back with MM_NO_STATE and the main router(2901) is either MM_NO_STATE or MM_SETUP.
I added the config for the 881, 2901 and a debug crypto isakmp and debug crypto ipsec from both routers. I have verified the Keys are correct and it is not blocking port 500. if i issue a sh crypto isakmp policy they are the same on both routers. if you need me to post anything else i will, one note i removed the configs that were part of the point to point tunnls on the 2901 router.
I have a client who would like to create a two VPN tunnels from one cisco 2901 router. One to the HQ and one to the DR. Is this possible?
View 4 Replies View RelatedI have just received a new cisco 2901 and started on its configuration. when I started configuring VPN tunnels, I saw that non of the crypto commands are available.
The router runs on iOS 15.1.From what I read, people refer that the router needs to past a license activation or something like that. When I run show verison - i do see "none" under most of the categories.
i have trouble to get the serial card (2nd genteration T1 card) on up/up state on a 2901 router. the SP guy who installed the rj48 at the demarc says it was tested good. For some reason, it is on up/down state no matter what i tried.
View 4 Replies View Relatedi need to know how many links i can using with load-balance on the same router ? i have router cisco 2901 , 3 providers , every provider having 4 links can i load balance between 12 links ? i am using static route
View 11 Replies View Relatedwhy router going to shut down mode after 15 or 30 min? Here is the #show tech support command. find the attached document.
View 3 Replies View RelatedI have configured PBR on my 1800 series router, it is working perfect. Now I am changing my router from 1800 to 2901 router with the same config, so the PBR stop working and I am not getting hits in the second WAN interface. [code]
View 2 Replies View RelatedI am trying to configure a 2901 router to act as NTP server on my network.This set "ntp master" in the router.I have no possibility to access an NTP server on the Internet.Now I want to configure a Windows 2003 DC to update the time from the NTP Server (router 2901).In Windows 2003, the registry value "Ntp Server" may have to be IP addresses or FQDN? (In my case I put router_ip_address, 0x1) 0x1 = use this "SpecialPollInterval" to update the time? Where you can find that these actions mean "next action is 3"? In Event Log in Windows 2003 DC receipt Event ID 35:The time service is now synchronizing the system time with the time source ROUTER2901_IP (ntp.m | 0x1 | W2K3_SERVER_IP: 123 -> ROUTER2901_IP: 123).Configure "Special Poll Interval" in 10 seconds.But the time on the Windows Server 2003 DC continuous five minutes ahead of time compared to the 2901 router.
View 2 Replies View RelatedI need to break into a 2901 router to recover the passwords. Cisco's methodology for password recovery on 2900 seriews routerssays to remove the compact flash card and reboot into RMON. There is no external compact flash card on a 2901. Is there acompact flash card inside the box? Or can you use the older method of rebooting and then hitting ctl+break to boot into RMON?
View 5 Replies View RelatedI've been looking to see if its possible to create a GRE tunnel between a Cisco 2901 with 3 adsl WIC cards and a Cisco ASA.The Cisco 2901 is at our remote office and we have 3 adsl lines for resillience as they tend to go down alot.The Cisco ASA is at our Head Office sitting behind our ISP's managed router.
The desired end result would be to have three GRE tunnels, 1 for each DSL line terminating on the ASA at head office and use EIGRP routing protocol to move traffic across to another tunnel should one fail, and encapsulate all of that with IPSEC.
Router : cisco 2901 with securityk9 licence
I used this manual : [URL]
Im trying to change de login page but the command doesn't work : ip admission proxy http login page file disk1:login.htmThis is what I see when I type (config)#ip admission ?
absolute-timer Absolute Timeout in minutes
auth-proxy-audit Authentication Proxy Auditing
auth-proxy-banner Authentication Proxy Banner
[Code].....
i'm interested if it's possible to set the NTP server via DHCP on an 2901 Router with 15.2(2) image.
i configured the interface gigabit 0/0 as dhcp client. The DHCP Server sends to me DNS, Default GW and NTP. All is working fine, but the NTP will not be configured. i tried to add an DHCP option request, but there is no NTP (42) value. [code]
is there any way to add the value NTP (42) for the DHCP request or isnt it possible?
i want to use the cisco 2901 router with two adsl cards(EHWIC-VA-DSL-B) and would like to know if that possible without any restrictions with the ip base license.
View 2 Replies View RelatedI want to configure a bsc network with a cisco 2901 router, but bstun commands are not enabled. I've already found a lot of tutorial about "How to configure bstun network" but none about how to enable it.
"show bstun", "show bsc", "bstun peer-name", etc. return "% Invalid input detected at '^' marker."
Here my "show version" :
Router#show version
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.1(4)M2, RE)
Technical Support: [URL]
Copyright (c) 1986-2011 by Cisco Systems, Inc.
[Code].....
I have a repating 2901 router failure when people attempt to download Apple Mac OS X Moutnain Lion upgrade from App Store.
The 2901 just hangs following getting a series of ZBFW packet drop failures:
001928: Jul 26 22:37:18.783 UTC: %APPFW-4-HTTP_PROTOCOL_VIOLATION: HTTP protocol violation (0) detected - session 192.168.223.109:49310 184.25.254.67:80 on zone-pair ZP-PRIVATE-OUT class ccp-protocol-http appl-class ccp-http-blockparam
[Code].....
when i try it comes up with secured with WPA/WPA2 PSK what is this and how do i get it
View 2 Replies View RelatedIs there a way to turn my old PC (P4 3.0GHz, 1GB RAM, 40GB HDD) into a Mobile Broadband Router using my Verizon 4G USB device? (like a CardlePoint router)I am searching some of the "PC to Router" software titles, but I am unable to find my type of setup: (support USB 4G as internet source)DD-WRT, ClearOS, ZeroShell, RouterOS, Untangle, etc.
-use my Verizon USB 4G device as my internet source
-have a single NIC on my PC router plugged into a switch
-all my other PCs would be plugged into the same switch
How do I connect my mobile phone to my computer network via bluetooth.The bluetooth wizard cannot find my device
View 1 Replies View RelatedCan I connect a mifi device to a 3g/4g mobile broadband router w/ USB port where I can plug a 3g/4g dongle?
View 2 Replies View RelatedI have a 3 Network USB Dongle which is the only thing that will work for receiving broadband at a remote location.
Also have a Kasda WiFi router It has a USB port on it (whether it is connected to anything inside?)
We want to send wifi around the house with the 3 Network broadband - can we utilize this router or have to get something else
I am looking for a 3G mobile broadband wireless router WITH dual band frequencies and 4 gigabyte ports OR could the DAP-1350 be connected to my DIR 655 that at least has the gigabyte ethernet ports? (Would I connect it to the Internet port or to one of the Ethernet ports and turn the 655 into an access point?)
I have a sprint 250u Sierra USB for my Internet. There isn't anything else available where I live, and don't even get me started on satellite Internet .What I'd like to do is have an Internet connection with a wireless router with dual band frequencies and at least 4 gigabyte switch ports to share a NAS device that I'm going to buy in the near future along with a printer and surveillance camera. That way I don't have to have multiple wireless devices to connect to for what I want to be able to do.
Region : UnitedKingdom
Model : TL-MR3020
Hardware Version : V1
Firmware Version : mr3020nv1_en_3_14_4_up(121129).bin
ISP : Three mobile data sim
Possible to use a mobile via the usb connection on a TL-MR3020. The reason being is that my mobile data plan allows unlimited tethering through my phone...yet when I place the sim from the phone in the usb modem I get blocked by the provider stating that the sim can only be used in a mobile phone. Mobile data plans in the UK are very expensive and you get very little for your money.
Currently I am hosting a 7 day mountain retreat, for about 90+ people. Clearly they are dependent on the internet teet as am I I am trying very hard to provide internet to our friends, but I just can't seem to figure it out I have a Mobile Broadband Router (MBBR) which limits connected devices to 6, so I figured that if connect a home router with wifi (WIFI) that allows 253 connections problem solved right? So I put a short LAN cable from the LAN port on the MBBR to the WAN port on the WIFI and presto! The WIFI gets a IP address, but does not allow other users of the WIFI to get internet. I've even killed all security on the WIFI and put the WIFIs IP in the DMZ on the MBBR. I noticed the DNS was the same as the gateway on the WIFI, so I changed that to the DNS on the MBBR still nothing.
PS Yes I have a connection on the MBBR I am on it now.Connecting the LAN cable from the MBBRs LAN to the WIFIs LAN extends the range, and grants internet to the WIFI users... but uses the MBBRs DHCP to give IP addresses, which limits to 6.I guess the goal here is bypass the limitation of the MBBR by using the WIFIs DHCP to issue IPs?
I want to share mobile broadband with another computer.One desktop running on windows7 and connected to wireless router netgear wgt624 v3 via ethernet cable. The other laptop is running on windows7 and has wireless card. Both computers are connected wirelessly via router on private network within workgroup and can share files between each other. The mobile broadband dongle is connected to desktop pc and desktop is running the internet Now I want the desktop pc which is running internet by wireless dongle to share that internet with laptop via wireless router. I have tried setting is up but couldn't do that. When I connect the dongle to desktop pc it use the same IP address 192.168.1.1 which is already used by wireless router. Tried to configure different IP in router but didn't work.
View 1 Replies View Related