Cisco WAN :: Configure PPOE On 2901 Router?
Oct 2, 2011
I have a 2901K ISR router IOS Version 15.0(1r)M12 and I will be using this as a internet router, The WAN interface will get dynamic IP from the ISP, so I need to configure PPOE. I am referring the following link for setting up PPOE. [URL] However I am unable to define PPOE protocol as shown below
INTERNETRTR(config)#!!!!! Configure Router as PPPoE Client to the ISP
INTERNETRTR(config)#vpdn enable
INTERNETRTR(config)#vpdn-group 1
INTERNETRTR(config-vpdn)#request-dialin
INTERNETRTR(config-vpdn-req-in)#protocol ?
l2tp Use L2TP
INTERNETRTR(config-vpdn-req-in)#
Any link for setting up PPOE on 2901 series router.
View 1 Replies
ADVERTISEMENT
Jul 5, 2011
I am attempting to configure a Cisco 2901 router using IOS 15 to properly perform NAT/PAT translation between LAN and the internet connection. I've configured DHCP pool for the local interface (GigabitEthernet0/1), which works properly. The WAN interface (GigabitEthernet0/0) is configured to obtain its own IP by DHCP from the ISP. I can work on the LAN computers and I can access the internet directly from the router (using, for example, telnet and router's ping commands). The problem is, NAT does not work properly and connection from the LAN interface does not reach the WAN interface.
View 1 Replies
View Related
Feb 1, 2011
i have trouble to get the serial card (2nd genteration T1 card) on up/up state on a 2901 router. the SP guy who installed the rj48 at the demarc says it was tested good. For some reason, it is on up/down state no matter what i tried.
View 4 Replies
View Related
Mar 10, 2012
I am attempting to configure a Cisco 2901 router using IOS 15 to properly perform NAT/PAT translation between LAN and the internet connection.
My Configuration:
interface GigabitEthernet0/0
ip address dhcp
ip nat outside
ip virtual-reassembly
no ip route-cache
duplex auto
speed auto
no cdp enable
no mop enabled(code)
View 28 Replies
View Related
Oct 16, 2012
I have a WRT160N that has its firmware updated and works fine thru a DHCP connection to my ISP. The issue is that my ISP is migrating all the accounts to PPoE and my router seems to be in loop once i set the PPoE connection and the connection stays intermittent, up and dow and at the end I can't use the PPoE account.
View 6 Replies
View Related
Aug 31, 2012
I just set up my e2500 from lynksys tech support with a motorola mode. i'm running dsl into my house laptops all connect no issues however my iphone 3gs will lose connectivity and received the ppoe failure this morning unplugging an plugging in both router/modem restes but that's a pain even doing a reset on my phone doesn't work.
View 4 Replies
View Related
Jan 25, 2012
Trying to install an E1200 inside a PPOE modem. I put in the account and password in the PPOE settings. I can see that it connects okay. But, my clients connected to the router (whether wired or wireless), do not get authenticated, so I can't get anywhere with them. Should I make the modem be the source of DHCP?
View 5 Replies
View Related
Apr 13, 2012
I'm using a refurbished E4200 that's connected to a SpeedStream 5360 modem to establish an Internet Connection over PPoE (ATT DSL). Connected to Ethernet ports I also have a NAS and an Airtport Express (with wireless off - it's only there for AirTunes/AirPlay).I'm getting Internet drop offs and then completely lose the WiFi, about every other day.E4200 drops Interaction Connection (PPoE)
View 4 Replies
View Related
Mar 19, 2012
I want to know the ppoe configuration in asa5505 firewall. IN my office i have a asa5505 and i get conncetion from local isp which is nothing but ppoe connection so how to do this.
View 1 Replies
View Related
Jan 31, 2011
I have a WAG320N and cannot get it to connect via PPoE.
i have IP, DNS etc but i cannot input the info manually
View 5 Replies
View Related
Dec 12, 2010
I have a SR520W-ADSL-K9, I´m trying to setup it trough CCA, but I have some troubles. At the internet connection I mark PPoE option, enter the vci=0, vpi=35, the username, the password (like the ISP TELMEX suggest), and mark the IP Negotiated option, but I have not find the ISP service give me an IP Address and establish the connection.
View 6 Replies
View Related
Dec 25, 2012
I want to configurate Vpdn protocol PPOE but i can not write protocol ppoe under vpdn group name on cisco 2811. cisco 2811 iso is 12.4 T adventurer and i upgrade it 15.1 advansecure but problem is still.
View 5 Replies
View Related
Jan 8, 2013
Here is the configuration : I newly installed for a client a RV110W (firmware 1.2.0.9) wich connect on the internet trough Dlink 320B (ppoe connexion, in France - the provider is orange). Wifi is ok, VPN is ok, wan is ok ...
But no way to make port forwarding works (form wan to lan of course). I tried to reboot the router, the modem, reseting router configuration before re-apply mine, it didn't made any change. I also tried single and range port forwarding, without any succes...
View 2 Replies
View Related
Aug 25, 2011
Cisco ASA 5505 Security Plus 1 link with PPOE dialup for internet access
desirable situation: Primary link with a PPOE dialup Secondary Link with DHCP address Asignment
Problem: i want to configure Dual ISP Failover modus, but the problem exist when i configure the ip sla syntax it looks good in the running config. but after a reload the secondary line becomes primary
It looks like the ppoe client authentication is busy when the ip sla tracking mechanism becomes active. can i tweak the settings that the ip sla tracking mechanism starts later?
What i the correct config for Dual ISP setup with primary PPOE and secondary DHCP
View 1 Replies
View Related
Mar 17, 2011
I have one router 1841 in which i configured PBR for internet traffic from LAN. I hv two ISPs few server are configured for ISP1 and few for ISP2.I planned to shift my existing setup at 2901 G2 router. when I am configuring the same config on this router so traffic is passing through only from one ISP not from other, if I troubleshoot so I see that the interface which is connected with ISP2 is not getting any input/output packet.
Config is here:
==========
interface FastEthernet0/0
description ****** ISP2 ******
ip address 203.xx.xx.110 255.255.255.248
[Code].......
View 1 Replies
View Related
Apr 18, 2011
I have a 2901 ISR G2 router, with IOS 15.0.1M3 , this router is not working with static NATing, I have tried to configure this router with one internet link and make few static translations with it. But this configuration is perfectly working with 1841 ISR router.
View 2 Replies
View Related
Feb 28, 2013
I'm trying to run the ISM-VPN-29 in a 2901 router. Cisco says that the SECK9 and HSECK9 licenses are needed to operate this ISM. However, they also say that the HSECK9 license is not available on the 2901. I'm running the SECK9 license but it's still not working.
This link, table 5 states that the HSECK9 feature license is for 2921 and 2951 only:[URL]This link states that it is a requirement to run the card, and also that the card works on the 2901:[URL]
I am running 15.3(1)T IOS.
View 3 Replies
View Related
Dec 24, 2012
how to install VIC3-2E/M in cisco router 2901 & what precaution should have to be taken.
View 2 Replies
View Related
Jul 1, 2012
I have a 2901 router and I would like to enable the following feature router mobile. [code] I used c2800nm-advipservicesk9-mz.151-3.T1.bin on a 2811 and this worked without any problem.Is there a possibility that there is some kind of license associated with this feature on a 2901?
View 1 Replies
View Related
Apr 15, 2013
Trying to setup a DMVPN on out existing equipment that is currently running all point to point vpn connections. basicly its not working. my best guess is something with the config is interfering but i'm not sure the remote router (881) is always comming back with MM_NO_STATE and the main router(2901) is either MM_NO_STATE or MM_SETUP.
I added the config for the 881, 2901 and a debug crypto isakmp and debug crypto ipsec from both routers. I have verified the Keys are correct and it is not blocking port 500. if i issue a sh crypto isakmp policy they are the same on both routers. if you need me to post anything else i will, one note i removed the configs that were part of the point to point tunnls on the 2901 router.
View 3 Replies
View Related
Feb 18, 2013
I have a client who would like to create a two VPN tunnels from one cisco 2901 router. One to the HQ and one to the DR. Is this possible?
View 4 Replies
View Related
Jan 13, 2013
I have just received a new cisco 2901 and started on its configuration. when I started configuring VPN tunnels, I saw that non of the crypto commands are available.
The router runs on iOS 15.1.From what I read, people refer that the router needs to past a license activation or something like that. When I run show verison - i do see "none" under most of the categories.
View 6 Replies
View Related
Jan 10, 2012
i need to know how many links i can using with load-balance on the same router ? i have router cisco 2901 , 3 providers , every provider having 4 links can i load balance between 12 links ? i am using static route
View 11 Replies
View Related
May 22, 2011
why router going to shut down mode after 15 or 30 min? Here is the #show tech support command. find the attached document.
View 3 Replies
View Related
Dec 22, 2010
I have configured PBR on my 1800 series router, it is working perfect. Now I am changing my router from 1800 to 2901 router with the same config, so the PBR stop working and I am not getting hits in the second WAN interface. [code]
View 2 Replies
View Related
Sep 19, 2012
I am trying to configure a 2901 router to act as NTP server on my network.This set "ntp master" in the router.I have no possibility to access an NTP server on the Internet.Now I want to configure a Windows 2003 DC to update the time from the NTP Server (router 2901).In Windows 2003, the registry value "Ntp Server" may have to be IP addresses or FQDN? (In my case I put router_ip_address, 0x1) 0x1 = use this "SpecialPollInterval" to update the time? Where you can find that these actions mean "next action is 3"? In Event Log in Windows 2003 DC receipt Event ID 35:The time service is now synchronizing the system time with the time source ROUTER2901_IP (ntp.m | 0x1 | W2K3_SERVER_IP: 123 -> ROUTER2901_IP: 123).Configure "Special Poll Interval" in 10 seconds.But the time on the Windows Server 2003 DC continuous five minutes ahead of time compared to the 2901 router.
View 2 Replies
View Related
Feb 18, 2013
I need to break into a 2901 router to recover the passwords. Cisco's methodology for password recovery on 2900 seriews routerssays to remove the compact flash card and reboot into RMON. There is no external compact flash card on a 2901. Is there acompact flash card inside the box? Or can you use the older method of rebooting and then hitting ctl+break to boot into RMON?
View 5 Replies
View Related
Jul 6, 2011
I've been looking to see if its possible to create a GRE tunnel between a Cisco 2901 with 3 adsl WIC cards and a Cisco ASA.The Cisco 2901 is at our remote office and we have 3 adsl lines for resillience as they tend to go down alot.The Cisco ASA is at our Head Office sitting behind our ISP's managed router.
The desired end result would be to have three GRE tunnels, 1 for each DSL line terminating on the ASA at head office and use EIGRP routing protocol to move traffic across to another tunnel should one fail, and encapsulate all of that with IPSEC.
View 8 Replies
View Related
Jan 16, 2013
Router : cisco 2901 with securityk9 licence
I used this manual : [URL]
Im trying to change de login page but the command doesn't work : ip admission proxy http login page file disk1:login.htmThis is what I see when I type (config)#ip admission ?
absolute-timer Absolute Timeout in minutes
auth-proxy-audit Authentication Proxy Auditing
auth-proxy-banner Authentication Proxy Banner
[Code].....
View 1 Replies
View Related
May 2, 2012
i'm interested if it's possible to set the NTP server via DHCP on an 2901 Router with 15.2(2) image.
i configured the interface gigabit 0/0 as dhcp client. The DHCP Server sends to me DNS, Default GW and NTP. All is working fine, but the NTP will not be configured. i tried to add an DHCP option request, but there is no NTP (42) value. [code]
is there any way to add the value NTP (42) for the DHCP request or isnt it possible?
View 4 Replies
View Related
Dec 5, 2011
i want to use the cisco 2901 router with two adsl cards(EHWIC-VA-DSL-B) and would like to know if that possible without any restrictions with the ip base license.
View 2 Replies
View Related
Jan 19, 2012
I want to configure a bsc network with a cisco 2901 router, but bstun commands are not enabled. I've already found a lot of tutorial about "How to configure bstun network" but none about how to enable it.
"show bstun", "show bsc", "bstun peer-name", etc. return "% Invalid input detected at '^' marker."
Here my "show version" :
Router#show version
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.1(4)M2, RE)
Technical Support: [URL]
Copyright (c) 1986-2011 by Cisco Systems, Inc.
[Code].....
View 4 Replies
View Related
Jul 25, 2012
I have a repating 2901 router failure when people attempt to download Apple Mac OS X Moutnain Lion upgrade from App Store.
The 2901 just hangs following getting a series of ZBFW packet drop failures:
001928: Jul 26 22:37:18.783 UTC: %APPFW-4-HTTP_PROTOCOL_VIOLATION: HTTP protocol violation (0) detected - session 192.168.223.109:49310 184.25.254.67:80 on zone-pair ZP-PRIVATE-OUT class ccp-protocol-http appl-class ccp-http-blockparam
[Code].....
View 9 Replies
View Related
