I have a SR520W-ADSL-K9, I´m trying to setup it trough CCA, but I have some troubles. At the internet connection I mark PPoE option, enter the vci=0, vpi=35, the username, the password (like the ISP TELMEX suggest), and mark the IP Negotiated option, but I have not find the ISP service give me an IP Address and establish the connection.
View 6 Replieswe have cisco sr520 adsl router at one of the sites. A device is connected to the LAN and needs to be communicated directly to the server with 3rd party over internet. we have a static public IP( a.b.c.d) for cisco router and want this IP redirected to the LAN IP address(192.168.1.20) of the device but locked to only 2 inbound IP address (eg.-1.2.3.4 , 5.6.7.8) .
View 1 Replies View RelatedI want to configurate Vpdn protocol PPOE but i can not write protocol ppoe under vpdn group name on cisco 2811. cisco 2811 iso is 12.4 T adventurer and i upgrade it 15.1 advansecure but problem is still.
View 5 Replies View RelatedI have cisco sr520 adsl router. I have configured two vlans i need in vlan 2 speed only 2 Mbit/s from 6Mbit/s (full speed).
View 1 Replies View RelatedI'am a bit newbie at using Cisco products and here is my problem : I have set up a VPN tunnel between 2 Sites (A and B) a few month ago using 2 cisco SR520-ADSL-K9. All was working fine until power failures occured on the sites B (secondary site).
What happened was that none of the ethernet ports were working, excepting during booting, I was then able to ping computers linked to ports Fastethernet0, FastEthernet1, FastEthernet2 and FastEthernet3 but after a few seconds all ports were disabled but my DSL seemed to be working.
So I took back the router home to check it. I managed (I think) to make a factory reset using a serial terminal and following the procedure described here [URL]
Since I did the reset, I thought I would be able to re-use Cisco Configuration Assistant (3.1) to re-configure the router (I am very bad at using the command lines) but I am unable to connect to the router using the supposed default IP : 92.168.75.1 (I set my computer to use 192.168.75.50 IP adress with mask 255.255.255.0). But I can't connect to the router ... even if the Ethernet ports seem to work because green light is on when plugging my cable. connect to my router using CCA ?
For more information, here is what I get when I run "show startup-config" and "show running-config" in terminal console. I guess the objective is to make the startup-config beeing the running-config, but I have no idea on how to do that ..
show startup-config
show running-config
Router#show startup-config
[Code]......
We've (an independent school) just bought an SR520 with a view to replacing one of our Draytek 2820s. We need to set up some site-to-site VPN with NAT and the Drayteks won't do it.
I've been trying to configure the SR520 in just the most basic fashion using CCA (3.1) and the CLI but with no success. I can't get a PPP connection with our ISP.
I've tried following the instructions in the software config pdf and also tried replicating the various 'running configs' reported in other posts in this forum to allow connection to a UK ISP, with no success. I don't know how many times I've reset the poor thing to factory defaults.
I have to say that I'm dismayed at how flaky the CCA appears to be. Many of the things I've tried with it simply don't work and often end up in it hanging. Close to useless in my view.
So instead I've tried to use the CLI which seems a lot more solid but is somewhat impenetrable and there's precious little by way of supporting explanation.
to configure this router my main objective is ADSL connection, and wireless network setup.
[code]...
I got myself lately Cisco SR520 router with some basic firewall functions built in. This is going to be used for my home broadband, so no need to be really super secure, as it would be for some business. I managed to configure it, however there are few things on the firewall side, which I don't understand.
This router had some default configuration in it's flash, when I bought it. There are class maps.... how it works or how to add/edit rules. Also, do I need to use class maps, or can they be replaced by ACL's to certain extend? How to add/edit class maps rules to allow certain port (eg. 3333). Pease see below part of the default config:
class-map type inspect match-any SDM-Voice-permit
match protocol sip
class-map type inspect match-any sdm-cls-icmp-access
match protocol icmp
match protocol tcp
[Code]...
I have a SR520 just deployed at a remote site with Internet Access.
Working Environment:
Remote sites have SR520 with IPSEC VPN back to HQ and netflow v.5 works through the VPN back to our PRTG server.
Non-Working:
I cannot get Netflow data to our PRTG with this first SR520 implemented with Zone Base Security. I am not able to get my netflow traffic out. VPN is up and running. Internet is a dialer0 interface. I have a Kron job that does the copy run to tftp backup daily to the same PRTG server and it works fine.
Both my source interface and address on the TFTP command and the netflow commands are the same interfaces (VLAN75) and IP. The Destination ip is the same too (through the VPN tunnel).
Snipped:
flow exporter prtg
destination x.x.x.x
source Vlan75
[Code]....
I have a fresh SR520 that I only did two things to it using CCA 3.2(1):
1. Assign the address of FA4 to be 1.23.456.90 with a mask of 255.255.255.252
2. Declared a static nat of 1.23.456.90 port 80 to 192.168.75.12 port 80
I connected laptops to two ports:
1. FA0 (DHCP assigned laptop the address 192.168.75.12)
2. FA4 with the address on the laptop set to 1.23.456.90 and mask of 255.255.255.252
This is an exercise to simulate a cable internet configuration I will install the SR520 into.I can ping and point my browser to 1.23.456.89 and access the web server running there on port 80 via the inside laptop.I CANNOT point my browser to 1.23.456.90 from the outside laptop and make a connection.
What I am doing wrong with NAT? (I believe the problem lies therein as I did even try telling CCA to delete the firewall and I still could not connect to the inside web server).I have a network monitor (Wireshark) on the inside and see nothing coming across. I THINK I see successful NAT translations in the NAT logging (also in the attachment).
Here is the configuration : I newly installed for a client a RV110W (firmware 1.2.0.9) wich connect on the internet trough Dlink 320B (ppoe connexion, in France - the provider is orange). Wifi is ok, VPN is ok, wan is ok ...
But no way to make port forwarding works (form wan to lan of course). I tried to reboot the router, the modem, reseting router configuration before re-apply mine, it didn't made any change. I also tried single and range port forwarding, without any succes...
Trying to install an E1200 inside a PPOE modem. I put in the account and password in the PPOE settings. I can see that it connects okay. But, my clients connected to the router (whether wired or wireless), do not get authenticated, so I can't get anywhere with them. Should I make the modem be the source of DHCP?
View 5 Replies View RelatedI'm using a refurbished E4200 that's connected to a SpeedStream 5360 modem to establish an Internet Connection over PPoE (ATT DSL). Connected to Ethernet ports I also have a NAS and an Airtport Express (with wireless off - it's only there for AirTunes/AirPlay).I'm getting Internet drop offs and then completely lose the WiFi, about every other day.E4200 drops Interaction Connection (PPoE)
View 4 Replies View RelatedI have 3 877 ADSL routers for internet connectivity. I recently installed a FW behind them and would like to use the Ciscos as load balance in order to get better utilization from my 3 internet links.
1) the 3 routers are on DHCP from the ISP on the WAN side.
2) the 3 ciscos are on the same class C subnet on the LAN side: 10.201.1.252, 10.201.1.253 and 10.201.1.254
i'm looking for a cisco 881 configuration with SDSL line as nominal and ADSL as backup.
View 9 Replies View RelatedWe have 2 router cisco 2621XM and want to configure a VPN between them, but first we want to configure ADSL in both with the card installed.
View 2 Replies View RelatedI need to configure configuring pppoe ADSL on cisco 887VG
View 5 Replies View RelatedI have cisco 1801W . Earlier I am using ADSL dynamic IP address on RJ 11 through the ADSL Port but now the ISP change the connection to RJ45.
I am trying to configure it but unable to do this. ADSL line is okay because When I am connecting through the ISP router it is working fine. I have connected the ADSL RJ45 cable in the router fast ethernet 0.But I wanted to use Cisco 1801 Router so that I can use the ADSL as primary and ISDN as the backup.
Below is my configuration, eiteher this is possible to configure ADSL through RJ45 in 1801 and what configuration require for this.
Router#show ip int brief
Interface IP-Address OK? Method Status Protocol
FastEthernet0 unassigned YES DHCP up up
BRI0 unassigned YES unset administratively down down
BRI0:1 unassigned YES unset administratively down down
BRI0:2 unassigned YES unset administratively down down
[code].....
i want to use the cisco 2901 router with two adsl cards(EHWIC-VA-DSL-B) and would like to know if that possible without any restrictions with the ip base license.
View 2 Replies View RelatedBasically I have a simple LAN of 30 users and 2 servers that sit on a private address range (192.168.1.1 - 254). I have a Cisco 1921 router with 2 Gigabit Ethnet interfaces and have installed a 2 port Ethernet module to expand interfaces,I have Two Internet providers that provide me an Optic connection to a converter and then a CAT 5 cable. On both of these connections have private public assigned IP addresses.I have a email server and webserver on the LAN (192.168.2 and 192.168.1.3) and with to port forward various ports to these servers - 25, 80, 443 3389, and 2222.
In my external DNS I have two MX records for the mail server (mail.globalhomegroup.com) that point to 2 A records - one record for the publicly assigned IP address of one ISP and another IP address for the other ISP. Ideally what i would like is for mail to be delivered to the first ISP Ip address - the one with the lower MX weighting and then if that line goes down, through the IP address of the second MX record - the backup ISP we are using.
So I guess I am port forwarding to the inetrnal server IP addresses via one of the two external interfaces.At the same time I need to allow internal users to access HTTP, HTTPS etc.So I have managed somehow to configure the external interfaces of the routers to connect to the ISPs and have managed to assign IP info to intenral LAN interface. I can telnet to the router from the Internet via Dialer0 or Dialer1. Other than that I am totally stuck - I have tried to configure and debug NAT etc but cant see wood for the trees now. Basically the port forwarding is not working and i am not sure if the config I have done is in anyway correct.
I have a Cisco 1721 router with an ADSL wic. I have followed guides on the Cisco website so that I can connect the router to my home adsl connection. The router connects to my broadband provider and sucesfully obtains an IP address along with Dynamically assigned DNS servers. I am able to ping google.co.uk from the router but not from clients attached via DHCP.
I have noticed that if I ping the IP address of google.co.uk from a client it resolves but it will not resolve the name. This would lead me to believe that the problem lies with DNS resolution/forwarding but I do not know how to investigate further.
I have the requirement to provide a Cisco Router with 3 x ADSL lines (768k) to increase the internet speed.PPP multilink is not supported from the ISP.
Is it possbile to distribute the traffic between this three ADSL lines?How can I configure this?
I have the following hardware configuration:
1 x CISCO1921-SEC/K9
2 x EHWIC-VA-DSL-B
The third ADSL line is connected over an ADSL modem at one fixed Router Gigabit interface.
Is the ADSL line interface on Cisco 877W not initialising a known issue? This interface on my router has been in this state for more than one month, with the rest of the router seemingly operational. The interface was connected directly to my ADSL broadband and worked well for two years. But then, about a month ago, the interface went down. I saw the exact moment this happened recorded as a syslog message. The only information was that the interface status had changed to down.
Initially I thought this was a matter of reload the router and all will be well. Did not happen. Then I thought my broadband connection was to blame. However, this option was quickly ruled out. So I went on to exhaust all troubleshooting options, including reflashing the router with the saved image and totally changing the configuration. Still no change. I have had to go back to my old BT home hub for internet access. In terms of speed this actually works a lot better than the Cisco router. But I would still rather have the router connected to my broadband line. What can I do to bring the ADSL interface back to life?
We currently have a main network running through a static broadband connecting using a Cisco 1700 ADSL router, everything is working fine locally.
We are looking to rent some space in an office nearby so im going to order another business adsl connection with static IP for this site and i currently have a spare 1800 router.My question is can the cisco routers connect up like a VPN connection so both sites work together and will the connection remain online constantly so from the remote office we can access all our servers from the main network?
Also how does the IP addressing work on 2 sites. The main network uses 10.120.21.x and DHCP is assigned from a cisco router. Does the remote network assign from the same DHCP server or would the remote sites cisco router need to be setup to give out DHCP to local machines. If so what would be the best IP setup to use.
In a site we currently have 1 BT provided ADSL link which is currently terminated using their device which I believe is some kind of 2wire device, which is extremely slow due to distance from the Exchange (4Mbps)...We have a growing number of users here and want to install a second ADSL line from BT to give them increased performance.
We have a Cisco 2800 sat not doing much so I was wondering if I could use this to load balance the link? I know BT do not support MPPP so therefore the maximum any user can get will be the speed of a single link (4Mbps)...But basically how can this be done..
Can I leave the two BT routers in place and place the Cisco 2800 behind them, or do I need to purchase two ADSL modules for the 2800 and terminate the connection there?Also once done, what do I need to do regarding actually setting up the load balancing? I have seen this:
[URL]
But am unsure as to how relevant it is? I am not sure I understand what the ACL's are being used for? I just want all users on the LAN to load balance out...
Also I am unsure of this statement:You potentially need to add policy-based routing for specific traffic to ensure that it always uses one ISP connection. Examples of traffic that require this behavior include IPSec VPN clients, VoIP handsets, and any other traffic that use only one of the ISP-connection options to prefer the same IP address, higher speed, or lower latency on the connection.I do not understand why a established session such as a VPN client, would ever traverse the second ISP connection anyway?
I've moved a Cisco 887 router from a site where it was used to dial up on an ADSL line to a new site where we have a EFM circuit which terminates at a Cisco 1841 router managed by our ISP. I therefore need to re-configure our 887 router to work as a conduit from our servers back to the Cisco 1841 as its gateway.
I have asked from our ISP and they told me that i need to configure the 887 to use IP address 176.35.140.65 255.255.255.248 and its gateway should be 176.35.140.70. That's great advice in theory but I don't know how to configure this correctly
Our internal network is using subnet 192.168.42.XX which will need to be retained for local devices.
I have Cisco 871 router with 12.3. OS version.
1. I'm interested if it's possible to block certain contetn only at certain time ? e.g. We would like to block facebook from 7:00 to 10:00 and from 11:00 to 15:00. I was going through cisco manuals but can't find the right answer to this.
2. Cisco 871 has 4 LAN interfaces and one WAN interface. Currently WAN interface is connected to adsl modem in bridge mode and LAN 0 interface is connected to switch.
I'm interested if I could use remaining 3 LAN interfaces for adsl connections same as I'm using WAN interface. Then I would create vlans that would use LAN interface 0. Each of those VLAN's would use different adsl connection.I would assign different IP to each VLAN's so users would be able to change their gateway and use different ADSL connection.
I have a 2901K ISR router IOS Version 15.0(1r)M12 and I will be using this as a internet router, The WAN interface will get dynamic IP from the ISP, so I need to configure PPOE. I am referring the following link for setting up PPOE. [URL] However I am unable to define PPOE protocol as shown below
INTERNETRTR(config)#!!!!! Configure Router as PPPoE Client to the ISP
INTERNETRTR(config)#vpdn enable
INTERNETRTR(config)#vpdn-group 1
INTERNETRTR(config-vpdn)#request-dialin
INTERNETRTR(config-vpdn-req-in)#protocol ?
l2tp Use L2TP
INTERNETRTR(config-vpdn-req-in)#
Any link for setting up PPOE on 2901 series router.
I want to know the ppoe configuration in asa5505 firewall. IN my office i have a asa5505 and i get conncetion from local isp which is nothing but ppoe connection so how to do this.
View 1 Replies View RelatedI have a WAG320N and cannot get it to connect via PPoE.
i have IP, DNS etc but i cannot input the info manually
I have a WRT160N that has its firmware updated and works fine thru a DHCP connection to my ISP. The issue is that my ISP is migrating all the accounts to PPoE and my router seems to be in loop once i set the PPoE connection and the connection stays intermittent, up and dow and at the end I can't use the PPoE account.
View 6 Replies View RelatedI have reset the router of Cisco 870. I need to connect the router for ADSL connection but don't know how to do it.
[code]...
I have an 1700 cisco Router and a ADSL connection to Internet.How may I use it on my home network?There's any configuration that I should to do?
View 3 Replies View Related