Cisco WAN :: SR520 ADSL Router - Speed Limit On VLan 3?
Jan 15, 2012I have cisco sr520 adsl router. I have configured two vlans i need in vlan 2 speed only 2 Mbit/s from 6Mbit/s (full speed).
View 1 Replies
ADVERTISEMENT
Cisco WAN :: SR520 ADSL Router Direct Communication
Mar 15, 2011we have cisco sr520 adsl router at one of the sites. A device is connected to the LAN and needs to be communicated directly to the server with 3rd party over internet. we have a static public IP( a.b.c.d) for cisco router and want this IP redirected to the LAN IP address(192.168.1.20) of the device but locked to only 2 inbound IP address (eg.-1.2.3.4 , 5.6.7.8) .
View 1 Replies View RelatedCisco WAN :: SR520-ADSL-K9 - Can't Even Connect To Router After Power Failures
Aug 6, 2012I'am a bit newbie at using Cisco products and here is my problem : I have set up a VPN tunnel between 2 Sites (A and B) a few month ago using 2 cisco SR520-ADSL-K9. All was working fine until power failures occured on the sites B (secondary site).
What happened was that none of the ethernet ports were working, excepting during booting, I was then able to ping computers linked to ports Fastethernet0, FastEthernet1, FastEthernet2 and FastEthernet3 but after a few seconds all ports were disabled but my DSL seemed to be working.
So I took back the router home to check it. I managed (I think) to make a factory reset using a serial terminal and following the procedure described here [URL]
Since I did the reset, I thought I would be able to re-use Cisco Configuration Assistant (3.1) to re-configure the router (I am very bad at using the command lines) but I am unable to connect to the router using the supposed default IP : 92.168.75.1 (I set my computer to use 192.168.75.50 IP adress with mask 255.255.255.0). But I can't connect to the router ... even if the Ethernet ports seem to work because green light is on when plugging my cable. connect to my router using CCA ?
For more information, here is what I get when I run "show startup-config" and "show running-config" in terminal console. I guess the objective is to make the startup-config beeing the running-config, but I have no idea on how to do that ..
show startup-config
show running-config
Router#show startup-config
[Code]......
Cisco Firewall :: Limit Speed On Port Or VLAN ASA 5505
Aug 7, 2012We need to have one connection with less internet bandwidth assigned to it than all other other connections. Basically it is a separate conection from all others, incoming just from one switch port and separate VLAN.I know this can be done on the switch by limiting the bandwidth allocated to a port,
however, is it possible to have the speed limited down, just before it goes to the internet, ie, on the ASA, rather than doing it on the switch?The firewall is an ASA 5505.
Cisco Firewall :: SR520 ADSL Router - How To Add / Edit Class Maps Rules
Mar 26, 2013I got myself lately Cisco SR520 router with some basic firewall functions built in. This is going to be used for my home broadband, so no need to be really super secure, as it would be for some business. I managed to configure it, however there are few things on the firewall side, which I don't understand.
This router had some default configuration in it's flash, when I bought it. There are class maps.... how it works or how to add/edit rules. Also, do I need to use class maps, or can they be replaced by ACL's to certain extend? How to add/edit class maps rules to allow certain port (eg. 3333). Pease see below part of the default config:
class-map type inspect match-any SDM-Voice-permit
match protocol sip
class-map type inspect match-any sdm-cls-icmp-access
match protocol icmp
match protocol tcp
[Code]...
Cisco Switching/Routing :: SR520 ADSL Connection With PPoE?
Dec 12, 2010I have a SR520W-ADSL-K9, I´m trying to setup it trough CCA, but I have some troubles. At the internet connection I mark PPoE option, enter the vci=0, vpi=35, the username, the password (like the ISP TELMEX suggest), and mark the IP Negotiated option, but I have not find the ISP service give me an IP Address and establish the connection.
View 6 Replies View RelatedCisco Routers :: Total Failure To Get SR520-ADSL-K9 To Connect To ISP
Dec 15, 2011We've (an independent school) just bought an SR520 with a view to replacing one of our Draytek 2820s. We need to set up some site-to-site VPN with NAT and the Drayteks won't do it.
I've been trying to configure the SR520 in just the most basic fashion using CCA (3.1) and the CLI but with no success. I can't get a PPP connection with our ISP.
I've tried following the instructions in the software config pdf and also tried replicating the various 'running configs' reported in other posts in this forum to allow connection to a UK ISP, with no success. I don't know how many times I've reset the poor thing to factory defaults.
I have to say that I'm dismayed at how flaky the CCA appears to be. Many of the things I've tried with it simply don't work and often end up in it hanging. Close to useless in my view.
So instead I've tried to use the CLI which seems a lot more solid but is somewhat impenetrable and there's precious little by way of supporting explanation.
Cisco Routers :: Configure SR520 To Route Internet VLAN To Firewall
Jan 20, 2012My operations manager says "Could you go on-site and configure a new clients new internet connection?" I make the arrangements and go on-site. As I'm working with the providers tech he says "Do you have a sub-interface confgured for a dot1q VLAN id of 1057?", I say "What?". Anyway my firewall is not capable of dot1q VLAN, so he says "Do you have a Cisco router that can provide the trunking?", I say "Yes, I tink so but not with me". The question is can I use an SR520 between my firewall and the provider demarc to route the VLAN he is talking about? My initial discovery says yes but I am not quite sure of the details on how to achieve this on the SR520.
View 2 Replies View RelatedCabling / Cards :: Download Speed Breaks Without A Speed Limit?
Jan 24, 2013On board NIC: Intel 82579V Gigabit Network Controller (asus sabertooth x79 motherboard)I installed the drivers for it from intel's site.f I set link speed to auto (chooses 100mbps full duplex) or 100mbps full or half duplex, any HTTP downloads get slowed to a crawl (30kbps) (steam downloads remain at normal speeds). If I set it to 10mbps full duplex, download speeds jump to normal (500kbps for most HTTP sources)his happens on just this new computer (wired connection), any other computers on the network (wireless) work just fine
View 8 Replies View RelatedADSL Speed Drops Down With Router
Dec 27, 2011[code] My connection is ADSL with 2Mbps broadband. Using speedtest.net for testing the speed I got almost 2Mbps, that is ok, but this is connected directly to the modem. The problem is when I use the router, when I connect it the speed downs onward until it achieve a stable value of 512kbps, that is 4 times less than my contracted speed. I have tried with four different D-Link routers (DIR-280, DIR-600, DIR-600 N150, DIR-615), four ones give the same problem.D-Link tech support people don't have idea about what is happening just like tech support people from my Internet provider. I think the problem is not the modem because I get 2Mbps from it connected directly (without the router).I do the speed test in an interval of 3 minutes between each test, with just one device connected and only doing the speed test, all programs that use Internet access are closed.
Always is the same, after a time the speed drops down, from 2Mbps until 512kbps. The router has the QoS disabled, I have tried changing the MTU value, I have tried some values 1492 (this is the official from the Internet provider), also I have tried some lower numbers 1400, 1200 but the result is the same. The router has as security only wpa2 and it has a static public IP, the modem is configured as bridge. I have also tried unplugging the phones, connected to the splitter, keeping away the wireless phones, moving away the router from the modem for electronic interference, modifying the WAN speed from auto to 10 and 100, I have disabled the firewall, change the channels and power TX. I do the speed tests using the wireless and wired interfaces.
Linksys E1200 Router - How To Limit Wi-Fi Speed
Jul 5, 2013I was wondering if theres a program or something that I could use for my router to limit the bandwidth that it gives on wifi? I currently have about a 20down/2up connection from time warner with a linksys E1200 router.
I just want to limit the wifi speeds to about 70% because recently someone moved in that does a lot of downloads and makes my games go from 40 ping to 300+ and also my phone is through the internet, which becomes unusable.
just some simple setting to set the max wifi data to 13megabits/s down 1mbit up or something.
Cisco Switching/Routing :: 1841 Router - How To Limit Download Speed On 1 NIC
May 12, 2013I have 10Mbps internet speed connected to ciusco router 1841 that has 2 internal NICs. One NIC has a full 10Mbps download speed and the 2nd NIC is currently limited to 1Mbps download speed. I want to change the download speed of the 2nd NIC to 4Mbps? How do I do this on a cisco 1841 Router?
View 8 Replies View RelatedLinksys Wireless Router :: E2000 / Limit Bandwidth Speed Of Guest Accounts?
Jul 7, 2011How can I limit bandwidth speed of guest accounts? Or are there free softwares available to do something like that? It's kinda like the hotspot softwares - where we can set hourly, daily, monthly allowances and see a report on their connectivity.
View 3 Replies View RelatedLinksys Wireless Router :: Ea3500 Can't Seem To Find Option To Limit Wifi Speed?
Dec 2, 2012With my old routeur (wrt310n) I used to be able to limit the wireless speed.I cant seem to find the option with my new routeur, EA3500.did they remove the option ?
View 1 Replies View RelatedCisco :: Limit Certain Users On A VLAN?
Jan 8, 2013what would be the best method to limit some users/workstations from accesing the internet on a vlan that has access to the internet?
I was thinking of just creating a whole new VLAN for those few workstations that doesnt access the internet or using ACLs on the ASA.
How To Limit Speed Of Wireless User
Oct 22, 2011How can I limit the speed of the wireless user.(I am using lan connection).
View 8 Replies View RelatedControl And Limit Internet Speed On Lan?
Oct 14, 2012I wan to ask whether i can control and limit my internet speed on LAN or not cos nowadays i have internet shop, but i couldn't control download bandwidth of each customer who come to download. Sometimes, it's effected to other customer using internet too,
View 1 Replies View RelatedD-Link DIR-615 :: How To Limit Speed On Some Computers
May 15, 2011i recently bought the dir-615, and i have 4 computers connected to it, 2 desktops with ethernet cables and 2 laptops with wifi. I want to know how to limit the internet speed on some computers, because i sometimes need full speed on my desktop. Is it possible within the router configuration interface?
View 1 Replies View RelatedD-Link DIR-615 :: Download Speed Limit
Jul 11, 2011I bought my d-link 615 a few days ago and managed to connect it to my network and so on but I have a problem when it comes to my download speed. My usual speed is somewhere between 7.5-8 mb/s but when I have the router installed it's limited to 5 mb/s. Do you know why this might be happening?
View 14 Replies View RelatedHow To Limit Internet Speed For A Specific Computer
Nov 11, 2011I have five computers in my shop., and I have 2 Mb speed of Internet connection. want to split internet speed equally for every computer.
View 1 Replies View RelatedHome Group Network Speed Limit?
Dec 29, 2012Home group network speed limit?
View 1 Replies View RelatedUSB Wireless Adapter Internet Speed Limit?
Jan 6, 2013I have a Belkin wireless N router and my PC uses a dual band wireless N USB stick. My internet speed when hardwired is 30 MB but when connected using my USB adapter it does not exceed 15 MB. Is there a limit on USB adapters and is there a way to increase the internet speed here?
View 8 Replies View RelatedHow To Limit Speed To Lock Bandwidth Of Each Computer
Jul 7, 2011I own a cyber cafe. I was told that switches are smart enough to distribute the same speed to all the clients. So I was not worried at first. But now if 2-3 customers starts watching youtube videos the rest starts complaining about the speed. I googled for the solution but got none. How to limit the speed,I want to lock the bandwidth of each computer.
View 8 Replies View RelatedPreserve Vlan Tag Over ADSL?
Oct 26, 2011Customer needs to send tagged traffic from various DSL sites (DSL is with us) and wants to be able to see vlan tags in the core. Essentially each site will have a vlan tag associated with it.
View 19 Replies View RelatedLimit The Internet Speed Of One System In Home Network?
Jan 31, 2012In my home We have 3 pcs.
1. my personal PC1
2. home or general PC2
3. wireless PC (not important here.)so PC1 and PC2 are connected directly to internet via this [URL] modem router. I have full control over everything and I did setup the whole thing.We have a limited bandwidth internet plan, but a lot of bandwidth is easily used up by PC2.I want to limit the speed of internet access on that PC2 so that downloading becomes impossible or difficult.
Cisco Firewall :: ASA 5510 - Rate Limit The Internet Bandwidth / Speed?
Jul 29, 2012In ASA 5510. How I can limit the users in (VLAN 20) to use the internet with a limited Bandwidth/speed with 3 mbps upload and 5 mbps download?
In case the outside interface (Native vlan) which is connected to the ISP and have a bandwidth/speed of 30 mbps upload and 50 mbps download.
Cisco Switches :: SG300 To Configure VLAN Rate Limit
Apr 14, 2013I have a Cisco SG300 small business switch and 541 APs. There are 2 VLANs in our network. One must be limited by bandwidth. How to configure vlan rate-limiting on SG300? And describe CIR & CBS.
View 1 Replies View RelatedCisco Switching/Routing :: WS-C6509 / VLAN Interface Limit
Jan 2, 2012I have Cisco WS-C6509 with IOS version 12.2(18)I have several vlan interface on this device.Today I create new vlan intervace
interface Vlan165
description test5
ip address 10.10.10.1 255.255.255.252
end
and vlan:
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
165 test5 active Gi7/14
But I can't ping this IP address and show ip route shows:
sh ip route 10.10.10.1
Routing entry for 10.10.10.0/24
Known via "static", distance 254, metric 0 (connected)
I have static route for this subnet /24?I can not see any error in logs, but looks like I reached vlan interface limit on this device or something like this.How can I check it?
Cisco WAN :: Connecting ADSL Line On HWIC-ADSL On Router 2901?
Aug 24, 2012i have a problem with my adsl line connected on a HWIC-ADSL on router 2901 it was working good until yesterday the atm interface is down but the interface dialer is up .i connected this line into home adsl modem and the line is working good?
View 2 Replies View RelatedCisco Switching/Routing :: QoS Limit Specific VLAN Within Trunk 4506
Jan 25, 2012Need to limit the amount of bandwidth a specific VLAN can use on a 802.1q trunk port. Situation is that we have a pair of Catalyst 4506 switches which have 802.1q trunk ports into a Checkpoint Firewall, this in turn is connected to a managed WAN router (to which I can't apply a QoS policy).If the 4506 was routing the traffic it would be easy to setup a class-map to match the IP traffic and then QoS the traffic, but the VLAN in question is trunked directly into the firewall (no L3/IP presence on the 4506 next hop for all clients on this VLAN is the firewall).What I need to do is restrict any traffic from this specific VLAN to 10Mbps on the uplink to the Checkpoint Firewall so it cannot impact the onward WAN.
View 1 Replies View RelatedCisco Switching/Routing :: 4096 - Limit Number Of Vlan Trunk
Nov 15, 2011a number of vlan on trunk is 4096, can I limit this number? I need trunk pass only 10 vlans.
View 1 Replies View RelatedTp-link Adsl2+ Wireless :: W8960n / Wifi Speed Download Limit 4mb On Ios And Android Device
Nov 18, 2012Region : Italy
Model : TD-W8960N
Hardware Version : V4
Firmware Version : 67406
ISP :
I have problem on router td-w8960n v4 internet speed download is limited a 4 mb in device android e ios wifi connected for test i use application speedtest.net on ipad 3 and samsung galaxy s
Cisco :: DMVPN With OSPF Area Router Limit And Per-area Limit?
Oct 31, 2012need to know the OSPF best design. I have a customer currently running their OSPF only in two area. Area 0 is provider reside and area 1 reside 700 hundred over of router including HQ router and remote branch router connecting to metro-E 10Mbps networks. Is this design have any weakness? Area 1 about 800 hundred router reside in, the HQ model is cisco router 7200 and remote end is cisco router 1841.Let's say they want a solution, for 3G remote router connect back to the HQ using Lease line with a fixed IP. Using DMVPN and OSPF communicating back to HQ. What should we aware when designing and implementing for the OSPF best practice. They have 700 hundred over remote branch need to terminate back to their HQ. I read cisco recommend an area should not be more than 50 router and per-area no more than 28 area.
View 4 Replies View Related