I have 10Mbps internet speed connected to ciusco router 1841 that has 2 internal NICs. One NIC has a full 10Mbps download speed and the 2nd NIC is currently limited to 1Mbps download speed. I want to change the download speed of the 2nd NIC to 4Mbps? How do I do this on a cisco 1841 Router?
View 8 RepliesOn board NIC: Intel 82579V Gigabit Network Controller (asus sabertooth x79 motherboard)I installed the drivers for it from intel's site.f I set link speed to auto (chooses 100mbps full duplex) or 100mbps full or half duplex, any HTTP downloads get slowed to a crawl (30kbps) (steam downloads remain at normal speeds). If I set it to 10mbps full duplex, download speeds jump to normal (500kbps for most HTTP sources)his happens on just this new computer (wired connection), any other computers on the network (wireless) work just fine
View 8 Replies View RelatedI bought my d-link 615 a few days ago and managed to connect it to my network and so on but I have a problem when it comes to my download speed. My usual speed is somewhere between 7.5-8 mb/s but when I have the router installed it's limited to 5 mb/s. Do you know why this might be happening?
View 14 Replies View RelatedI want to know is it possible to check Internet speed directly in the cisco router thru any command or activating any service in the cisco router?.As it is seen most of the times internet speed offer by ISP is different as compared to clients.and Clients most oftenly not satisfied with internet speed The problem is that our ISP has given us 100MB leaased line.But when we deployed in production network the speed is same as DSL.We have reported this issue to ISP they then carried out Iperf test by connecting laptop directly with the ISP router.They have tested the speed and it shows about 94-96 Mbps and argu that it is up to the mark and there is problem at your side(i.e our internal network).Now our internal network has cisco 1841 router connected directly to ISP 3825 cisco router.Our router has minimum configuration as required to pass traffic out and in.Our internal 1841 router is connected to switch to which different clients are connected.We have performed some online tests using different speed checking websites and also perform real time tests by uploading and downloading files.The speed is much low as compared to 100Mbps and it is nearly or slightly higher then as DSL connection. how can we check internet speed in the specified scenario?Is there any command or service available in cisco router to check internet speed as we want to check ISP connection speed directly thru 1841 router?what about authenticity of online speed checking websites?Any specialize software/tool you recommend to check Internet speed in specified scenario?
View 11 Replies View RelatedRegion : Italy
Model : TD-W8960N
Hardware Version : V4
Firmware Version : 67406
ISP :
I have problem on router td-w8960n v4 internet speed download is limited a 4 mb in device android e ios wifi connected for test i use application speedtest.net on ipad 3 and samsung galaxy s
I have 1841 router with Gigabit Ethernet HWIC with One SFP Slot installed in it and connected via SX Multimode cable to 2950 switch. I have 5 VLans in trunk. The question is what will be the speed rate between VLans - 1 Gbps or less?
The case:
Port 1 assigned to a VLan10 and Port 2 Assigned to a VLan20 on 2950 switch.
InterVLan routing is configured on 1841.
Computer A is connected to Port 1 and Computer B is connected to Port 2 on the switch.
What be a file transfer rate from Computer A to Computer B assuming that NICs on both computers are 1000Base-T.
I just discovered that my wireless download speeds are 5Mbps, compared to 16Mbps if my laptop is connected directly to the modem or wired through the router. Uploads are 2Mbps either way. I have a WRT54GS v.6 with firmware version v1.52.8 which I updated today, completed by setting factory default through the router webpage after I discovered this discrepancy. The firmware update did not improve the download speed appreciably, if at all.Should the wireless connection be that much slower than the wired connection through the router? If not, what sort of issues could I be having to account for this?
I did just replace my modem when I discovered I was having erratic speedtests and that corrected that problem. That is when I became aware of the wireless issue, so not sure how long that has been the case. I have Charter's 16/2 HSI, living in a sparsely populated area with solid internet service. There is no external nor internal interference on this 2.4Ghz band.
We have some point-to-point sites linked with our HO with 10-30mbps speed. We have provided DID telephone lines to these sites as well.
We want to limit the bandwidth with 1mb bandwidth only and also make sure that the voice traffic (DID telephone lines) gets the priority over all other traffic even if they are utilitizing the 1mb link completely. We have some Cisco 1841 routers that we are planning to configure on the main uplink on each of these sites. how to give the priority to the voice traffic yet limiting the bandwidth to 1mb.
I was wondering if theres a program or something that I could use for my router to limit the bandwidth that it gives on wifi? I currently have about a 20down/2up connection from time warner with a linksys E1200 router.
I just want to limit the wifi speeds to about 70% because recently someone moved in that does a lot of downloads and makes my games go from 40 ping to 300+ and also my phone is through the internet, which becomes unusable.
just some simple setting to set the max wifi data to 13megabits/s down 1mbit up or something.
I have cisco sr520 adsl router. I have configured two vlans i need in vlan 2 speed only 2 Mbit/s from 6Mbit/s (full speed).
View 1 Replies View RelatedI have a task of setting up bandwidth limit on the 2811 router Fastethernet interfaces.The scenario is:We have a 4MB Internet connection and would like to allocate bandwidth usage to users.
Fastethernet 0/0 needs to be set with 256KB output and 2048 input. This is going to be connected to a wireless router. Fastethernet 0/1 needs to be configured with 2048 output.I could also use SDM if that's easier than using CLI.
I have a cisco 2821 router where as a cisco 2960 switch with connect on router as a trunk & one user vlan . this is my WAN router all traffic are internal . i have 2MB data connectivity on my WAN side. i have to Give a specific Bandwith on my SAP traffice . like when SAP traffice will come they all time get around 50 % bandwidth of my channel. If SAP resuest are not comming then other traffice will get full bandwith .
View 4 Replies View Relatedconfiguring a switch or a router to limit the bandwidth for a specific user/IP when need it. Most of my remote offices are configured like this:
Users ------ 3560 switch ------- 2801 router -------- T1 to NOC -------- 7204 router with channelized DS3
I use Netflow Analyzer for high bandwidth usage alerts and can see the user's IP right away when someone is clogging our T1s. My goal is to be able to temporarily limit the bandwidth of the user taking over the T1. Whatever is best switch config or on the router.
We have a Cisco 1841 router that requires 2 levels of access, at the moment we have network admins logging in with a single username via SSH and with privilege 15 but we also need our helpdesk to login to run certain commands but not chaneg anything
View 4 Replies View RelatedI've never had a router's CPU suddenly hit 99% and just stay like it for hours even after a reboot. This router really does nothing with regards to CPU, I'm looking at it's CPU history (via SolarWinds Orion NPM software that we use) and it is arounf 1-3% all the time for the past 2 years.
I did a show debugigng and it seems no debugging is running
We currently have a Cisco 1841 router with version 12.4(1c) of IOS using image c1841-ipbase-mz.124-1c.bin. Our goal is to make it so our router can fully support IPv6. The current IOS version cannot. I've seen a site that seems to indicate 12.4T does support with IP Base image but recently had Cisco tell me with the latest IOS release 15.1.4.M4 that I have to use either the "Advanced Enterprise Services" or "Advanced IP Services" image. Did Cisco just remove IPv6 from IPBase in later IOS releases?
Also I've seen conflicting specs on the max amount of Flash and DRAM the router can support. The following link shows that 384MB is the max for DRAM and 128MB max for flash. We're looking to upgrade ours from 128MB and 32MB respectively but as mentioned I've seen it where higher amounts are supported. In fact we bought a backup 1841 to have and it has a 256MB Flash card in it.URL
Last but not least. Where can I find a straightforward documention of this situation where we may have to upgrade our Flash and DRAM and then upgrading the IOS?
Recently my desktop has experienced very slow download speeds (~0.11 Mbps), however the upload speed appears to be in line (~2.0Mbps). These numbers are taken from Comcast's speed test (my ISP). It is obviously a problem with my PC because everything else on the network (PS3, Laptop) have great signals with no problems. I just recently reverted the Desktop back to its factory state, and everything was working fine for a couple of months. The desktop in question uses Vista 32-bit and the Belkin Basic USB Wireless Adapter.
View 1 Replies View RelatedHow can I limit bandwidth speed of guest accounts? Or are there free softwares available to do something like that? It's kinda like the hotspot softwares - where we can set hourly, daily, monthly allowances and see a report on their connectivity.
View 3 Replies View RelatedWith my old routeur (wrt310n) I used to be able to limit the wireless speed.I cant seem to find the option with my new routeur, EA3500.did they remove the option ?
View 1 Replies View RelatedI live in the tampa bay area, I have bright house (BHN) as my service provider, which provides a Road Runner Lightning (40/5) package. I previously used BHN's top tier (20/2) back in July (and prior) with no problems.
After converting to Lightning in August of this year (2010). Of course, BHN (and every other provider) wants to force a modem/router down your throat, so I had them bridge it (in short, turn it into a dummy modem with no routing). I had an SMC branded modem gateway at the time. I work from home 2 days a week (so I can spend more time with my kids during morning, lunch, right after work) and this requires me to use QoS to ensure my VOIP work calls don't get dropped, if the family is watching youtube videos or watching netflex.
My network was as follows SMC Modem >WAN IP>>WAN Port>>D-link DIR-655>>Switch Ports>PC1, PC2, PC3
Everything seemed fine (from a usability stand point) till about 2 weeks ago when my upload speed seemed to grind to halt. Normally I was able to upload about 200-300K per second, and I noticed this dropped to about 45K per second during a drop box upload. First thing I did was power cycle both my modem and router (in the proper/usual order). After they both come up, I start using speed test to find out what my upload speeds were. I was getting about 39Mbps down, but only .56Mbps up still. I factory reset my router.... test, similar speeds. Power cycle all computers (just in case), and then modem/router. Tested, similar speeds. Updated the firmware to the latest. Same issue
Called BHN customer service, they factor reset it, but it wasn't in bridge mode. If I by passed the 655, in factory mode (non bridge mode) upload speeds returned to better than expected states. If I bridged the cable modem, upload speeds seemed to crash.
Had BHN replace the modem, seemed fixed for a day, then issue came back. Had them come back out and replace it again, this time with a Motorolla Surfboard modem... same issue. Fine during factory reset, however after they bridge the modem, upload speeds were fine. Told BHN I would take it from there.. Connected up the DIR-655, and upload speeds crashed again. (.6Mbps). Called D-Link Support, and the Chinese English speaking rep seemed to not be listening to me and tried to have me adjust my MTU as well as Wireless settings. Long story short... the rep was a level 0 id10t and I hope D-link will consider hiring better employees/contractors. So I was all about to give up and replace it with a DD-WRT capable router (which it takes me a lot to want to swap hardware), when I discovered the wan shaping was on. Which I thought to myself... nah... QoS has never messed up before... why would it be the cause. Turned off wan shapping... and voila. Issue seemed to be insta-resolved.
Unsatisfied with that... I decided to dig a lil deeper. I turned on Wan shaping again, but decided to set the settings manually instead of auto detect.
Here are the settings I used... (Advanced Tab>QoS)
Enable Traffic Shaping - Checked
Automatic Uplink Speed - Unchecked
Manual Uplink Speed - 5000
Connection Type: Cable or Other Broadand Network
Enable QoS Engine - Checked Automatic Classification - unchecked (this checked seemed to affect my upload speed by about 5-10% during testing) Dynamic Fragmentation - unchecked (this checked seemed to be the worse enemy for upload speed)
While I know I'm not any network guru (still have to use a subnet calculator for subnetting), I think I did a pretty good job drilling down the issue (once I got passed my service provider replacing modems).
Anyways, I've had overall good luck with D-Link products, even have a 5 port 10/100 switch (all metal) from 1998 that works great. Hopefully, D-Link will just either put more documentation on the web, or hire better employees.
I have got a l2 link of 512 kbps from two different ISP. I want to aggegrate the bandwidth of this connection so that I can feel like having 1 mbps connection. I am not actually talking about load balancing, but bandwidth/link aggegration. Can we have the solution of failover with different vlan from different isp ? Can we be able to make the link as a single link.
View 2 Replies View Relatedestablishing a Static NAT on an 1841 router.
I'm at a FOX affiliate TV station, and in order to connect our EAS Device to the internet & Fox Splicer, I need to setup a Statio NAT, so we picked up an 1841 on eBay.
I've done a little configuration in HyperTerminal.
I've done these ip addresses:
FE0/0 10.1.10.13 this is the subnet our EAS device is on
FE0/1 10.110.81.174 this is the subnet of the Fox Splicer.
I need to have NAT translate 10.1.10.11 to 10.110.81.170 and I also need to set a route for 10.110.81.0/24 pointing to 10.110.81.161
Hava cisco router 1841 forgot user name and password and need to reset it to its factory setting
tried boot while holding ctrl and break get into rommon1>
rommon1>confreg 0*2142
rommon1>reset
still shows rommon 3>
I have the following devices for our IT Test LAB
1. Cisco 1841 with 2 Fast Ethernet interfaces fa0/0 & fa0/1
2. Cisco 2960-S
3. Speedstream 6200 DSL Modem ( PPOE Connection with Static IP address)
I want to connect to the internet using the current DSL connection we currently have .
LAPTOP --> SWITCH 2960 --> ROUTER 1841 ---> DSL Modem ---> ISP
Troubleshooting 1: Currently from the LAPTOP i am able to ping
1. Switch 2960 Vlan interfaces
2. Router 1841 fa0/0 & fa0/1
BUT can not Ping the DSL Modem LAN interface IP 192.168.2.1 and can not get out to the INTERNET
Troubleshooting 2:currently from the Switch 2960 i can ping
1. All the Vlan interfaces on the Switch 2960
2. Router 1841 fa0/0 & fa0/1 interfaces
3. Laptop A & B
But can NOT ping the DSL modem LAN interface IP 192.168.2.1 and can not get out to the internet
Troubleshooting 3:Currently from the Cisco 1841 router i can ping
1. All the Vlan interfaces on the Switch 2960
2. Router 1841 fa0/0 & fa0/1
3. Laptop A & Laptop B
4. Can Get out to the internet. I am able to ping any internet destinations without any problem
VLAN ===> FE 0/1 {With subinterfaces - ALL INSIDE LAN INTERFACES} ==> ROUTER ===> BVI 0/1 {WAN Interface - OUTSIDE}
i am doing NAT for my clients in LAN to WAN - Static NAT i want one of my client who is excessing some service with his Public IP to get a specific amount of bandwidth ... as right now he is hogging all the bandwidth .i have 1841 router.
I'm using for a company network a 2801 Cisco Router. This router has 2 FastEthernet Interfaces connected on 2 ISP's and one VLAN for internal users. What acl should i use if for example one client from the lan is using a torrent client to download from the internet. I want just to specify a maximum download speed or to block that client to access the internet when it's trying to download something that can affect other clients from the LAN.
View 2 Replies View Relatedi have a laptop that i connect through our wireless router with, and for the past couple months my download speed have been terrible. my browsing speed is just as fast as it always was when i am connected to our router, just incredibly slow if i try to download or stream something.however, my downstairs neighbor also has a wireless router set up that i can access which gives me incredible download speeds but my cant even browse the internet because i the browser connection times out.i have tried plugging directly into my router to on the thought that perhaps the 2 routers' wireless was somehow interfering with each other, but my download speeds are still *** even then.
View 1 Replies View RelatedWhen I connect directly to my dsl modem, I am getting better than 5 megabits/sec. which is what I should be getting for download speed.When connected thru the router, I am getting about half of that.My wireless connection speed is 54 megabits/sec, so that is ok. I cannot get any connection when I hardwire the connection from the pc to the router too.
View 4 Replies View RelatedAny simple way of opening ports on a 1841 router.I have a working config for internet traffic. I am looking to boot up my Windows Server and Run IIS.
View 1 Replies View Relateddue to upcoming changes to our network I'd like to be able to pass vlans across the FE ports of a Cisco 1841 router.1 port would go to a managed switch and then to local devices on different VLANs.the 2nd port would go upstream to a Cisco 3825 at a different location which would then connect to the internet.due to monitoring behind the Cisco3825 we would like all NAT to occur on the 3825.
what I would like to happen is this example device connected to port 7 on managed switch gets an IP (10.0.7.10) from the Cisco 1841 in VLAN 7 (10.0.7.0/24).traffic from that device goes to the switch, then in f0/1 on the 1841 and out f0/0 still with the same IP info, no NAT occuring.traffic is received on the 3825 port 0/1 and then NAT occurs and out port 0/0 to the internet.
The issue is occuring on our local LAN where my ARP requests are being modified after a period of time by the router for one host. I'm finding that the host will work fine with the correct MAC IP pairing for a period of time and then about 15-30 minutes later, the arp table is changing so the associated mac/IP address is now the mac address of the router interface.
The FastEthernet 0/1 port has no ip proxy-arp enabled and is set with ip nat inside.This only started happening after restarting the router, however the running config was saved as the startup config prior to the restart.I've tried hard-coding the entry with the command arp 10.15.4.190 c82a.1459.0579 ARPA however that is not working as expected.
The device is an 1841 ISR with the advanced IP Services bundle loaded. Is there some way that the router is viewing my host (provides DNS, Directory Services) as a intrustion attempt and somehow rejecting the packets?
We have a setup of a firewall in between my Cisco 1841 router and Switch.
Cisco Router --> Meraki Firewall--> Switch
Client VPN is configured on the Meraki Firewall but then for the outside users to client vpn in to the network, I have to port forward or open the ports 500 and 4500 to the IP address of the Meraki Firewall 192.168.1.90. [code]
We have a 1841 Cisco router for one of our remote sites and we have the GRE over IPSec tunnel on it (with our datacenter router) for the connectivity. The LAN facing interface becomes UP/Down (status 'UP', Protocol 'Down'). When I login the router and 'shut' and then 'no shut' the interface, the interface becomes UP and everything starts to work. Traffic starts to flow across it. But after some time, some hours or sometimes some days, the interface is again back to up/down status. The router is connected to a non-Cisco switch. I do see some CRC's increasing very slowly, but apart from that there seems nothing wrong with the interface in sho int fas0/0 command:
!
RTR01#sho int fas0/0
FastEthernet0/0 is up, line protocol is down
Hardware is Gt96k FE, address is 0026.cb91.ee48 (bia 0026.cb91.ee48)
[Code]....