Cisco Switching/Routing :: Establishing Static NAT On 1841 Router
Mar 16, 2013
establishing a Static NAT on an 1841 router.
I'm at a FOX affiliate TV station, and in order to connect our EAS Device to the internet & Fox Splicer, I need to setup a Statio NAT, so we picked up an 1841 on eBay.
I've done a little configuration in HyperTerminal.
I've done these ip addresses:
FE0/0 10.1.10.13 this is the subnet our EAS device is on
FE0/1 10.110.81.174 this is the subnet of the Fox Splicer.
I need to have NAT translate 10.1.10.11 to 10.110.81.170 and I also need to set a route for 10.110.81.0/24 pointing to 10.110.81.161
View 12 Replies
ADVERTISEMENT
Oct 16, 2012
I'm trying to dial a Cisco 1841 BRI from my Cisco 2811 PRI. I'm getting a few errors but not sure what else to do to correct the issue. Config & Logs below from 1841:
interface BRI0/0/0no ip addressencapsulation pppdialer pool-member 2isdn switch-type basic-niisdn point-to-point-setupno cdp enableppp authentication chap callin
00:26:44: ISDN BR0/0/0 Q931: RX <- SETUP pd = 8 callref = 0x46 Bearer Capability i = 0x8890 Standard = CCITT Transfer Capability = Unrestricted Digital Transfer Mode = Circuit Transfer Rate = 64 kbit/s Channel ID i = 0x89 Signal i = 0x40 - Alerting on - pattern 0 Called Party Number i = 0xC1, '452####' Plan:ISDN, Type:Subscriber(local) Locking Shift to Codeset 5 Codeset 5 IE 0x2A i = 0x808001039E05, 'From ', 0x8B0C, '214 ###-####', 0x8001, '<'00:26:44:
[Code]....
View 2 Replies
View Related
Sep 2, 2012
I have a Cisco 1841 router at home with version 12.4(13r)T advanced ip services. The setup is extremely simple:
1) PPPOE dialer to my service provider over ADSL
2) Nat overload on the dialer interface.
3) 2 V LAN s one for home network (wired) and one for wireless both v LAN's are connected through interface v LAN s respectively.
My problem is when I configure static NAT to map RDP or any other protocol to inside hosts this does n`t work.
"
ip nat source static tcp 192.168.20.3 2222 interface Dialer1 2222
ip nat source static tcp 192.168.20.3 3389 xx.xx.xx.xx 3389 extendable
ip nat inside source list 20 interface Dialer1 overload
"
When I open wire shark and sniff the traffic on home computer which is the one I`m trying to reach I can't see any traffic. And While performing Nat debugging I am also not able to see traffic going to that port (for example 3389).
View 7 Replies
View Related
Jan 5, 2013
I guess i am just getting old and forgot how this works, or i have an IOS load with an undocumented feature in it.A customer of ours wishes to have their exchange server appear to the outside world on a seperate IP address as their public pool address is.in the past this has not been an issue, however in the current configuration we are unable to get the source address to appear per the NAT statement it always sources on the overloaded IP. below is the relevant NAT config, am i missing something, or have i hit a IOS feature? [code] There is a 45% chance i have forgotten everything i learned on the NOC desk and a 50% chance that it is somethine really stupid and 5% IOS is broken
View 5 Replies
View Related
Sep 12, 2012
We upgrade our Internet service in our India office which required a new router. The local vendor suggested an 1841, so that is what we have. It has two fastethernet ports on it.
The ISP (Airtel) provided the following IP address information:
Public WAN IP : 122.181.23.200/30
WAN IP : 122.181.23.202SUBNET MASK : 255.255.255.252GATEWAY : 122.181.23.201Pri DNS : 125.22.47.125Sec DNS : 202.56.250.5
[Code]......
View 5 Replies
View Related
Mar 21, 2013
I have configured Cisco 1841 router PAT buts its not worked, find the below configuration details,
In LAN interface
Interface gigabit Ethernet 0/0
no shutdown
[code]......
Similarly I have configured static and dynamic nat but its not works in my customer place.
View 18 Replies
View Related
Mar 7, 2012
We have a Cisco 1841 router that requires 2 levels of access, at the moment we have network admins logging in with a single username via SSH and with privilege 15 but we also need our helpdesk to login to run certain commands but not chaneg anything
View 4 Replies
View Related
Oct 7, 2012
I've never had a router's CPU suddenly hit 99% and just stay like it for hours even after a reboot. This router really does nothing with regards to CPU, I'm looking at it's CPU history (via SolarWinds Orion NPM software that we use) and it is arounf 1-3% all the time for the past 2 years.
I did a show debugigng and it seems no debugging is running
View 9 Replies
View Related
Jun 5, 2012
We currently have a Cisco 1841 router with version 12.4(1c) of IOS using image c1841-ipbase-mz.124-1c.bin. Our goal is to make it so our router can fully support IPv6. The current IOS version cannot. I've seen a site that seems to indicate 12.4T does support with IP Base image but recently had Cisco tell me with the latest IOS release 15.1.4.M4 that I have to use either the "Advanced Enterprise Services" or "Advanced IP Services" image. Did Cisco just remove IPv6 from IPBase in later IOS releases?
Also I've seen conflicting specs on the max amount of Flash and DRAM the router can support. The following link shows that 384MB is the max for DRAM and 128MB max for flash. We're looking to upgrade ours from 128MB and 32MB respectively but as mentioned I've seen it where higher amounts are supported. In fact we bought a backup 1841 to have and it has a 256MB Flash card in it.URL
Last but not least. Where can I find a straightforward documention of this situation where we may have to upgrade our Flash and DRAM and then upgrading the IOS?
View 3 Replies
View Related
Nov 18, 2012
I have got a l2 link of 512 kbps from two different ISP. I want to aggegrate the bandwidth of this connection so that I can feel like having 1 mbps connection. I am not actually talking about load balancing, but bandwidth/link aggegration. Can we have the solution of failover with different vlan from different isp ? Can we be able to make the link as a single link.
View 2 Replies
View Related
Sep 16, 2012
Hava cisco router 1841 forgot user name and password and need to reset it to its factory setting
tried boot while holding ctrl and break get into rommon1>
rommon1>confreg 0*2142
rommon1>reset
still shows rommon 3>
View 12 Replies
View Related
Jan 6, 2012
I have the following devices for our IT Test LAB
1. Cisco 1841 with 2 Fast Ethernet interfaces fa0/0 & fa0/1
2. Cisco 2960-S
3. Speedstream 6200 DSL Modem ( PPOE Connection with Static IP address)
I want to connect to the internet using the current DSL connection we currently have .
LAPTOP --> SWITCH 2960 --> ROUTER 1841 ---> DSL Modem ---> ISP
Troubleshooting 1: Currently from the LAPTOP i am able to ping
1. Switch 2960 Vlan interfaces
2. Router 1841 fa0/0 & fa0/1
BUT can not Ping the DSL Modem LAN interface IP 192.168.2.1 and can not get out to the INTERNET
Troubleshooting 2:currently from the Switch 2960 i can ping
1. All the Vlan interfaces on the Switch 2960
2. Router 1841 fa0/0 & fa0/1 interfaces
3. Laptop A & B
But can NOT ping the DSL modem LAN interface IP 192.168.2.1 and can not get out to the internet
Troubleshooting 3:Currently from the Cisco 1841 router i can ping
1. All the Vlan interfaces on the Switch 2960
2. Router 1841 fa0/0 & fa0/1
3. Laptop A & Laptop B
4. Can Get out to the internet. I am able to ping any internet destinations without any problem
View 10 Replies
View Related
May 12, 2012
Any simple way of opening ports on a 1841 router.I have a working config for internet traffic. I am looking to boot up my Windows Server and Run IIS.
View 1 Replies
View Related
Nov 6, 2012
due to upcoming changes to our network I'd like to be able to pass vlans across the FE ports of a Cisco 1841 router.1 port would go to a managed switch and then to local devices on different VLANs.the 2nd port would go upstream to a Cisco 3825 at a different location which would then connect to the internet.due to monitoring behind the Cisco3825 we would like all NAT to occur on the 3825.
what I would like to happen is this example device connected to port 7 on managed switch gets an IP (10.0.7.10) from the Cisco 1841 in VLAN 7 (10.0.7.0/24).traffic from that device goes to the switch, then in f0/1 on the 1841 and out f0/0 still with the same IP info, no NAT occuring.traffic is received on the 3825 port 0/1 and then NAT occurs and out port 0/0 to the internet.
View 4 Replies
View Related
May 12, 2013
I have 10Mbps internet speed connected to ciusco router 1841 that has 2 internal NICs. One NIC has a full 10Mbps download speed and the 2nd NIC is currently limited to 1Mbps download speed. I want to change the download speed of the 2nd NIC to 4Mbps? How do I do this on a cisco 1841 Router?
View 8 Replies
View Related
Dec 22, 2011
The issue is occuring on our local LAN where my ARP requests are being modified after a period of time by the router for one host. I'm finding that the host will work fine with the correct MAC IP pairing for a period of time and then about 15-30 minutes later, the arp table is changing so the associated mac/IP address is now the mac address of the router interface.
The FastEthernet 0/1 port has no ip proxy-arp enabled and is set with ip nat inside.This only started happening after restarting the router, however the running config was saved as the startup config prior to the restart.I've tried hard-coding the entry with the command arp 10.15.4.190 c82a.1459.0579 ARPA however that is not working as expected.
The device is an 1841 ISR with the advanced IP Services bundle loaded. Is there some way that the router is viewing my host (provides DNS, Directory Services) as a intrustion attempt and somehow rejecting the packets?
View 1 Replies
View Related
May 26, 2013
We have a setup of a firewall in between my Cisco 1841 router and Switch.
Cisco Router --> Meraki Firewall--> Switch
Client VPN is configured on the Meraki Firewall but then for the outside users to client vpn in to the network, I have to port forward or open the ports 500 and 4500 to the IP address of the Meraki Firewall 192.168.1.90. [code]
View 4 Replies
View Related
Nov 14, 2011
We have a 1841 Cisco router for one of our remote sites and we have the GRE over IPSec tunnel on it (with our datacenter router) for the connectivity. The LAN facing interface becomes UP/Down (status 'UP', Protocol 'Down'). When I login the router and 'shut' and then 'no shut' the interface, the interface becomes UP and everything starts to work. Traffic starts to flow across it. But after some time, some hours or sometimes some days, the interface is again back to up/down status. The router is connected to a non-Cisco switch. I do see some CRC's increasing very slowly, but apart from that there seems nothing wrong with the interface in sho int fas0/0 command:
!
RTR01#sho int fas0/0
FastEthernet0/0 is up, line protocol is down
Hardware is Gt96k FE, address is 0026.cb91.ee48 (bia 0026.cb91.ee48)
[Code]....
View 1 Replies
View Related
Nov 2, 2011
I want to know is it possible to check Internet speed directly in the cisco router thru any command or activating any service in the cisco router?.As it is seen most of the times internet speed offer by ISP is different as compared to clients.and Clients most oftenly not satisfied with internet speed The problem is that our ISP has given us 100MB leaased line.But when we deployed in production network the speed is same as DSL.We have reported this issue to ISP they then carried out Iperf test by connecting laptop directly with the ISP router.They have tested the speed and it shows about 94-96 Mbps and argu that it is up to the mark and there is problem at your side(i.e our internal network).Now our internal network has cisco 1841 router connected directly to ISP 3825 cisco router.Our router has minimum configuration as required to pass traffic out and in.Our internal 1841 router is connected to switch to which different clients are connected.We have performed some online tests using different speed checking websites and also perform real time tests by uploading and downloading files.The speed is much low as compared to 100Mbps and it is nearly or slightly higher then as DSL connection. how can we check internet speed in the specified scenario?Is there any command or service available in cisco router to check internet speed as we want to check ISP connection speed directly thru 1841 router?what about authenticity of online speed checking websites?Any specialize software/tool you recommend to check Internet speed in specified scenario?
View 11 Replies
View Related
Nov 9, 2012
I've moved a Cisco 887 router from a site where it was used to dial up on an ADSL line to a new site where we have a EFM circuit which terminates at a Cisco 1841 router managed by our ISP. I therefore need to re-configure our 887 router to work as a conduit from our servers back to the Cisco 1841 as its gateway.
I have asked from our ISP and they told me that i need to configure the 887 to use IP address 176.35.140.65 255.255.255.248 and its gateway should be 176.35.140.70. That's great advice in theory but I don't know how to configure this correctly
Our internal network is using subnet 192.168.42.XX which will need to be retained for local devices.
View 7 Replies
View Related
Dec 15, 2012
I am using Solawinds syslog and trying to get our Cisco routers send syslogs to our syslog server. I followed the procedure on Configuring Cisco Devices to Use a Syslog Server from [URL] Our Cisco swtches are all sending syslog messages but not the routers. I compared the config with our access switches but can't seem to find the problem:
Sample router config:
service nagleno service padservice tcp-keepalives-inservice tcp-keepalives-outservice timestamps debug datetime msec localtime show-timezoneservice timestamps log datetime msec localtime show-timezoneservice password-encryption!hostname WWF-RT1boot-start-markerboot-end-marker!security authentication failure rate 10 logsecurity passwords min-length 8logging buffered 4096logging rate-limit all 10logging console critical!aaa new-model!!
[Code] .......
is there a command that prevents the router from sending the syslog to the server?
View 2 Replies
View Related
May 30, 2012
I am just setting up a simple scenario with a 1841. Server @ 172.31.1.1 cannot ping 172.31.0.254 or 172.31.0.105. It can ping 172.31.1.250. The router can, on the other hand, ping devices on both networks. This is just for testing routing theory so I don't know why hosts on either side of the network cannot ping each other.
I am only using the FastEthernet interfaces on Router 1841.
View 3 Replies
View Related
Nov 23, 2012
On 1811W Router i have OSPF running and i do not need this static route.ip route 192.168.20.0 255.255.255.0 192.168.20.3,when i try to delete i get error ,1811w#,config t,Enter configuration commands, one per line. End with CNTL/Z.,1811w(config)#no ip route 192.168.20.0 255.255.255.0 192.168.20.3,%No matching route to delete,1811w(config)#.
View 7 Replies
View Related
Feb 21, 2012
VPN 1841, and static nat. I have to create VPN to connect to remote network, but problem is that they already use same subnet as mine. How to configure static nat on cisco 1841 so static nat will work and address will be translated in different IP when connection trough VPN.I have address 192.168.235.1 and I want to translate to 192.168.100.1,This 1841 is border router, and all VLNAs and VLANs routing is on 3650.
View 12 Replies
View Related
Mar 14, 2011
I have configured a L2L VPN on a Cisco 1841 ISR. I am statically NATing some of my internal hosts to IP addresses that are included in the encrypted traffic. Please note that not all of the internal hosts are being NATed. I am doing this to hid some of the real IP addresses on the inside network. I have confirmed that the VPN works, as well as the NATing of the VPN traffic. I have traditionally configured L2L VPNs on Cisco ASA 5500 series appliances, and this is my first attempt with the 1841 ISR. I just want other to take a look a see if I missed anything, or, could I have done some of the configuration more efficiently. All comments are welcome.
VPN-RTR-01#show runBuilding configuration...
Current configuration : 9316 bytes!version 12.4service timestamps debug datetime msecservice timestamps log datetime msecservice password-encryption!hostname VPN-RTR-01!boot-start-markerboot-end-marker!! card type command needed for slot/vwic-slot 0/0logging buffered 51200 warningsno logging consoleenable secret 5 xxxxxxxxxxxxxxxenable password 7 xxxxxxxxxxxxxxx!no aaa new-modelip cef!!!!no ip domain lookupip auth-proxy max-nodata-conns 3ip admission max-nodata-conns 3!!crypto pki trustpoint TP-self-signed-2010810276 enrollment selfsigned subject-name cn=IOS-Self-Signed-Certificate-2010810276 revocation-check none rsakeypair TP-self-signed-
[code]....
View 1 Replies
View Related
Feb 20, 2012
I have a Cisco 1841 with a DSL and 3G HWIC interface. I would like to setup the DSL as the primary link and then use the 3G as a backup interface. I am trying to accomplish this using the Floating Static routes with SLA object tracking.
I have tried various options, like having two tracked routes, one tracked route, changing administrative distances, multiple SLA's, etc etc.
My problem basically is that when the DSL (Dialer0) goes down and the 3G (Cellular0/1/0) takes over, that the SLA never changes back when the DSL is available again, so that the DSL can take over as the primary link again. [code]
View 3 Replies
View Related
Mar 12, 2013
The router 1841 is connected directly to the layer switch. the network diagram is below:
Office A --> Switch (L3) --> Router 1841 --> Internet --> Office B
However, when I transfer the file from Office A to office B, the speed very slow ( only around 40 kb/second), and there are an input error and CRC error:
Cisco-R1841#sh interfaces FA0/1
FastEthernet0/1 is up, line protocol is up
Hardware is Gt96k FE, address is 0019.e02f.03dd (bia 0019.e02f.03dd)
[Code]......
View 5 Replies
View Related
Feb 6, 2012
I'm just getting started with cisco kit so you will have to bare with me.I have a cisco 1841.i have a very wierd issue of routing...i cannot ping and browse through this.
View 3 Replies
View Related
May 31, 2013
I have a problem accessing my wireless router through VLAN sub-interface on my Cisco 1841 router. My hardware:
Cisco Catalyst 2960 switch (192.168.100.4 /24)
Cisco Catalyst 3550 switch (192.168.100.6 /24)
Cisco 1841 router (192.168.100.7 /24)
Asus RT N66U wireless router (192.168.100.2 /24)
Here's my network topology:
I have two VLANs - 10 and 20. 2 DHCP pools are configured on 2 1841's interfaces - 192.168.1.0 /25 and 192.168.1.128/26 with default router sitting on 192.168.1.1 and 192.168.1.129 respectively. No issues with obtaining IP address from any of those pools.Laptop connects to L3 3550 switch (switchport access vlan 10), which, in turn, connects to 1841 router through trunk (with VLANs 10 and 20 allowed).3550 is connected to 2960 through trunk with VLANs 10 and 20 allowed.Wireless router is connected to 2960.I can successfully ping my wireless router and outside world from 1841 from fa0/1 interface, but not from fa0/1.10 or fa0/1.20 sub-interfaces - all packets got dropped. My laptop can obtain IP from both pools (depending on port I connect it to), but can't ping my wireless router and anything beyond it.
I attach my configs:Cisco Catalyst 3550:interface FastEthernet0/1 switchport trunk encapsulation dot1q switchport mode trunk switchport port-security mac-address sticky speed 100!interface FastEthernet0/2 switchport trunk encapsulation dot1q switchport mode trunk!interface FastEthernet0/3 switchport access vlan 10 switchport mode access!interface FastEthernet0/4 switchport access vlan 20 switchport mode access!Cisco 1841:
ip dhcp pool Vlan10DHCP network 192.168.1.0 255.255.255.128 default-router 192.168.1.1 dns-server 208.67.220.220 domain-name home.local
!ip dhcp pool Vlan20DHCP network 192.168.1.128 255.255.255.192 default-router 192.168.1.129 dns-server 208.67.220.220 lease 0 12
interface FastEthernet0/1 ip address 192.168.100.7 255.255.255.0 duplex auto speed auto!interface FastEthernet0/1.10 description VLAN10 Sub Interface encapsulation dot1Q 10 ip address 192.168.1.1 255.255.255.128!interface FastEthernet0/1.20 description VLAN20 Sub Interface encapsulation dot1Q 20 ip address 192.168.1.129 255.255.255.192!
Routing table on 1841:
[code]....
View 19 Replies
View Related
Sep 19, 2011
I am having some trouble configuring dual NAT on a Cisco 1841.
The 1841 has three interfaces.
Fa0/0 - LAN
Fa0/1- Different private network
Fa0/1/0 - Connection to DSL modem
NAT overloading is configured on Fa0/1 and we have traffic that must be router there. We would like to have all internet access go through the DSL modem. Currently internet access is obtained through fa0/1 but is not ideal. I have floating static routes configured if the DSL link goes down. (Which is currently unplugged) I do not have physical access to the router at this moment. We would like to keep the config a simple as possible. It seems like route-maps may be one of our only options.
View 1 Replies
View Related
Oct 3, 2011
I have a 1841 router attached to 2 ISP's. Each ISPs provides different bandwithd. I want to do load balance between them, but I want to do some sort of weighted load blance, so as to assign more traffic to one ISP than the other. A kind of 70/30 (70% of traffic via ISP1, and 30% of traffic via ISP2).Is there a way to acomplish that? I already tried creating bogus /32 routes, but "cef" seems to be more clever and groups the bogus routes as one gw.
View 12 Replies
View Related
Aug 4, 2009
Basically I have an internet router (1841ISR) with 1 internal (LAN) connection and 2 internet connections. What I want to do is route specific traffic for 3 of my internally hosted services (smtp, https, etc) through one internet connection (fa0/0) and then route all other traffic through the unmanaged/dynamic IP ADSL connection (Dialer 0).
View 9 Replies
View Related
Dec 27, 2012
I have a stack of 2 x 3750X switches these are running 12.2(55)SE5. I needed to add some static IP routes and found that the ‘ip routing’ command is not supported. I came across a document that stated “On switches running the LAN base feature, static routing on VLANs is supported only with Cisco IOS Release 12.2(58)SE and later.” So I have upgraded to 12.2(58)SE2, but ‘ip routing’ is still not a valid command.
The release notes state:“On the Cisco Catalyst 3560-X and 3750-X Series, it adds support for 16 static IPv4 routes in the LAN Base image.”
I have read other posts that talk about running the ‘sdm prefer routing’ command which I have done, but I am still unable to add any routes or run the ‘ip routing’ command.
View 4 Replies
View Related
