Cisco Switching/Routing :: 1841 - What Is Speed Rate Between VLans - 1 Gbps Or Less
Nov 5, 2011
I have 1841 router with Gigabit Ethernet HWIC with One SFP Slot installed in it and connected via SX Multimode cable to 2950 switch. I have 5 VLans in trunk. The question is what will be the speed rate between VLans - 1 Gbps or less?
The case:
Port 1 assigned to a VLan10 and Port 2 Assigned to a VLan20 on 2950 switch.
InterVLan routing is configured on 1841.
Computer A is connected to Port 1 and Computer B is connected to Port 2 on the switch.
What be a file transfer rate from Computer A to Computer B assuming that NICs on both computers are 1000Base-T.
View 8 Replies
ADVERTISEMENT
Nov 6, 2012
due to upcoming changes to our network I'd like to be able to pass vlans across the FE ports of a Cisco 1841 router.1 port would go to a managed switch and then to local devices on different VLANs.the 2nd port would go upstream to a Cisco 3825 at a different location which would then connect to the internet.due to monitoring behind the Cisco3825 we would like all NAT to occur on the 3825.
what I would like to happen is this example device connected to port 7 on managed switch gets an IP (10.0.7.10) from the Cisco 1841 in VLAN 7 (10.0.7.0/24).traffic from that device goes to the switch, then in f0/1 on the 1841 and out f0/0 still with the same IP info, no NAT occuring.traffic is received on the 3825 port 0/1 and then NAT occurs and out port 0/0 to the internet.
View 4 Replies
View Related
Oct 9, 2012
This is existing network diagram and find attached file for configuration of Router and L3 Switch:ISP provided 6 Mbps internet access link with ethernet Handoff which is terminated over Cisco 1841.ISP also provided pool of 30 Public ip's 125.63.74.33 /27 , range from 125.63.74.34 to 125.63.74.62.In my current setup, all Inside to ouside traffic going out through 125.63.74.34 public ip because this public-ip NAT overload with Router F0/1 interface.
1) I want to divide 6 Mbps link physically into three parts 2Mbps, 2Mbps, 2Mbps for three VLANs.
2) I want to also configure each vlan IN/OUT traffic with different Public ip. is it possible or not ?
Vlan2 = 172.25.162.0 /24 => Inside to outside / Outside to inside traffic through 125.63.74.40
Vlan3 = 172.25.163.0 /24 => Inside to outside / Outside to inside traffic through 125.63.74.41
Vlan4 = 172.25 164.0 /24 => Inside to outside / Outside to inside traffic through 125.63.74.42
How can i configure above desired setup with CBWFQ
View 23 Replies
View Related
May 12, 2012
I got a Cisco 2800 router and am planning to use FastEthernet 0/1 to trunk in 802.11Q VLAN's to cater for some of our radio links. speed and operation of the sub-interface that will be created. Or explain it here. We got a radio link that we want to trunk into this Cisco 2800 and it is suppose to be connecting at 100Mbps but currently operating at around 80Mbps. Reports shows that the max in and out traffic for this link this year till today is 25Mbps. Will it not fail teh CPU etc ?
interface FastEthernet0/1
no ip address
!
[Code]....
View 11 Replies
View Related
Dec 19, 2011
Is there a switch that handle its 24/48 ports at 10 Gbps with copper?. I have checked 3750 X but just handle 2 SFP with 10 Gbps.The requirement is to use this switch as CORE and connect 12 switches (access) using its uplinks at 10 Gbps with copper ( in this case 3750 X can be used).using copper at 10 Gbps the distance is still 100 m?
View 9 Replies
View Related
Sep 30, 2012
We are using CISCO 4507R-E switch as our core/distribution switch. Out of the 7 available slots, 3 are currently being used. Descriptions is as follows:
Slot 1: 6 Port Fiber Line Card
Slot 2: 6 Port Fiber Line Card
Slot 3: Supervisor Engine
Slot 4: Empty
Slot 5: 48 Port Copper Line Card
Slot 6: Empty
Slot 7: Empty
We want to add extra 10 Gbps fiber links (approximately 12) using slot 6 and 7.
View 6 Replies
View Related
May 12, 2013
I have 10Mbps internet speed connected to ciusco router 1841 that has 2 internal NICs. One NIC has a full 10Mbps download speed and the 2nd NIC is currently limited to 1Mbps download speed. I want to change the download speed of the 2nd NIC to 4Mbps? How do I do this on a cisco 1841 Router?
View 8 Replies
View Related
Nov 2, 2011
I want to know is it possible to check Internet speed directly in the cisco router thru any command or activating any service in the cisco router?.As it is seen most of the times internet speed offer by ISP is different as compared to clients.and Clients most oftenly not satisfied with internet speed The problem is that our ISP has given us 100MB leaased line.But when we deployed in production network the speed is same as DSL.We have reported this issue to ISP they then carried out Iperf test by connecting laptop directly with the ISP router.They have tested the speed and it shows about 94-96 Mbps and argu that it is up to the mark and there is problem at your side(i.e our internal network).Now our internal network has cisco 1841 router connected directly to ISP 3825 cisco router.Our router has minimum configuration as required to pass traffic out and in.Our internal 1841 router is connected to switch to which different clients are connected.We have performed some online tests using different speed checking websites and also perform real time tests by uploading and downloading files.The speed is much low as compared to 100Mbps and it is nearly or slightly higher then as DSL connection. how can we check internet speed in the specified scenario?Is there any command or service available in cisco router to check internet speed as we want to check ISP connection speed directly thru 1841 router?what about authenticity of online speed checking websites?Any specialize software/tool you recommend to check Internet speed in specified scenario?
View 11 Replies
View Related
Sep 22, 2011
1841 - IPBASE 12.4.7d
We provide internet access for a number of clients sitting on our WAN, at present they have un-restricted access to the full bandwidth of our 1Gb internet pipe. As they are only paying for a proportion of that we want to set a Mbps limit on the clients, and idealy the device should be transparent between our router and the clients.
I have been trying to set up rate limits on a bridge on our 1841.
#
bridge 1 protocol ieee
bridge 1 route ip
bridge 1 bridge ip
[Code].....
I have tried many combinations but can't get this to limit the traffic, the client still draws as much as they can.
Does rate limit work on bridged interfaces? or am I going to have to try it routed instead?
View 4 Replies
View Related
Jul 6, 2010
Cannot access console baud rate has been changed by customer and I have tried all the standard ones 1200,2400 ect, have tried the J7 baud jumper on the mother board....?
View 11 Replies
View Related
Aug 6, 2012
It is said that the switching fabric of WS-C3750X-24T-E is 160Gbps.Could any body tell me what is switching fabric, any relevance or difference from forwarding rate?,Is there any document to know how will the switch reach the 160Gbps full switching fabric performance?
View 5 Replies
View Related
Jan 12, 2013
What s the fabric speed (backplane speed) of a Nexus 2232 10G EX?What is the forwarding rate (Mpps) of the same 2232 FEX?
View 6 Replies
View Related
Jun 10, 2012
I configured rate limit on cisco 2960 switch sexuss fully, but i could not configure in cisco 2950 (verson 12.1 (22).To confiure the same on 2950
View 4 Replies
View Related
Jun 9, 2013
How to rate limit a 3560 inbound and outbound using different QoS methods. I've read about vlan class maps/policy maps, using the rate limit command on the physical interface, using the srr-queue bandwidth command(it's a gig switch so not sure that would work) and marking all packets and then applying QoS. I'm just learning QoS so trying to figure all of this out and find the best way to do things.
Also, I was told to do this because it's not advisable to have a connection to your ISP that is not 10mb or 100mb on a switch, since they are not divisible by 10 and it can cause issues?
View 2 Replies
View Related
Oct 20, 2011
I am using Cisco 3560 as distrubution switch and want to limit port 445 traffic on 1 MB and applied rate limit statment on Gi0/1 port but switch unable to limit said traffic.rate-limit output access-group 120 1024000 128000 128000 conform-action transmit exceed-action drop.
View 25 Replies
View Related
Apr 18, 2012
I have a computer connected to a Switch3750G and another computer connected to another Switch3750G. Theses switches are connected through a Optical Fiber link in the uplinks of the boths Switchs 3750. The computers are connected in the access ports, this ports works at 1Gbps. My question is Which is the maximum transfer rate that should reach between these two computers.
View 2 Replies
View Related
Nov 5, 2009
To rate limit the 2960 switch port to 1 MB.I have made the specified chnages , how ever still it is reaching more tha 1 MB
Hard coded the bandwidth of port to 10 MB and have applied the specified command srr-queue bandwidth limit 10.
View 4 Replies
View Related
Mar 18, 2013
how to change the Baud Rate on Cisco 2900 SW utilizing ROMON ?
View 8 Replies
View Related
Jul 17, 2012
We have a guest wireless setup but I need to rate limit the users so no one hogs all the bandwidth. The WLC is connected into a 3750 which is doing all the routing between the vlans. I know I cannot shape the traffic on the 3750.
View 2 Replies
View Related
Mar 4, 2012
I am having an issue with VoiP phones giving me an insufficient bandwidth message. I have three remote locations connected to our main building using 2 Mb point to point ethernet solutions through TWC. Each remote location has a Cisco WS-C3560-24PS running IOS C3560-IPBASE-M, version 12.2(25) and have the cable modems plugged into port 1 on them. The remote buildings are labeled 192.168.101.xxx, 192.168.102.xxx, and 192.168.103.xxx. There are 14-16 VoiP phones in each remote building. The main building being in the subnet of 192.168.100.xxx. I have the 3560s connecting to a single port on a 2801 in the main building, all using the subnet of 192.168.253.xxx The phone server sits in our network at 192.168.100.203. I have created the ACLs, class maps, and policy maps on all of the equipment.
For the remote buildings I have the following:
ACL
===========
Extended IP access list VOIP
permit tcp any host 192.168.100.203 dscp ef
permit tcp any host 192.168.100.203 eq 5566
[Code]....
I have put a hub in to capture traffic via Wireshark to see if DSCP flags are being appropriately marked and I do see that all VoiP packets are getting marked with as EF. However, I have been receiving phone calls from people in the remote buildings stating that their phones will cut out, flash Insufficient Bandwidth on the LCD displays and then the call will cut back in. I am wondering if the 2801 is not applying QoS with the rate-limits in mind since it is set to 100 Mb, or is it an issue with trying to take 3 remote locations and bring them down into 1 port on the 2801?
View 6 Replies
View Related
Nov 26, 2012
How is it i can implement the command 'ip multicast rate-limit out group-list <access-list>' but i get the error "ip multicast rate-limit" command is not supported on 6509?
Is it an IOS limitation or a limitation of the switch series and subsequently can't be used at all?
View 2 Replies
View Related
Jun 8, 2013
How (and is) it possible to rate limit pps on an interface (physical/logical), on a 6509-E?The porpuse is to protect from attacks which lead to very high pps, bypassing traffic rate-limits, and effecting the device's performance
View 2 Replies
View Related
Mar 21, 2012
I am looking for step-by-step configuration on how to enable rate-limit and traffic shaping on Cisco 6513 vlan interfaces. I am not able to find this particular document on CCO.
View 3 Replies
View Related
Nov 14, 2011
I have a 2960 that I need to limit the uplink port to 50Mbps for 3 vlans and 350Mbps for another vlan. Would the following config achieve that or is this even possible for the 2960?
class-map match-any VLAN50-51-52
match vlan 50-52
class-map match-any VLAN53
[Code].....
View 1 Replies
View Related
Dec 24, 2012
I am running the latest version of 12.2(55)SE6 on the catalyst and I am looking for this command "lacp rate fast" but it is not there:
lab-c3750#conf t
Enter configuration commands, one per line. End with CNTL/Z.
lab-c3750(config)#interface g1/0/5
lab-c3750(config-if)#lacp ?
port-priority LACP priority on this interface
lab-c3750(config-if)#lacp
According to this link, it is supposed to work: [URL]Am I missing something?
View 2 Replies
View Related
Nov 27, 2011
I am configuring a 3560 to provide internet access for our customers and I need to make sure they don't use more bandwidth than they have contracted for.I see that the 3560 supports the rate-limit command, but was told that I should use traffic shaping and policing along with access lists to manage the bandwidth.Is there a reason that I should avoid using the rate-limit command - it looks much simpler.
View 10 Replies
View Related
Oct 30, 2011
I am trying to limit traffic inbound to 10Mbps on a gig interface 0/48 set to 100/full. So I downloaded some big files over this link and I'm able to see 30- 40Mbps or more. You can see from the show int - rate-limit command that parameters are never showing exceented so nothing has been dropped. [code]
View 3 Replies
View Related
Oct 3, 2012
Is it possible to rate limit on a L2 trunk port on a 3750?
current port config and ios are as follows;
interface GigabitEthernet1/0/50
description *** Connection to Fiber Link ***
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1,172
switchport mode trunk
end
flash:c3750-advipservicesk9-mz.122-46.SE.bin
i was wondering if the "srr-queue bandwidth limit 10" command would work to limit the output from this interface to be 10 % of the port bandwidth and then the same command could be done on the other side.
View 1 Replies
View Related
Feb 5, 2012
I'm trying to limit the bandwidth on certain ports to 3Mbps and others 1Mbps for a project, however when I do a bandwidth test from a website the speed on the router doesn't seem to change it's as if the changes over telnet aren't actually affecting the swtich's qos settings. I have verified that the policy is attached to the interface and the settings are correct as well.
Router
Telnet address: 10.xxx.xx.xx
Password:
[Code].....
View 1 Replies
View Related
Oct 8, 2012
I want to limit the bandwidth going to remote site on the switch connecting to our netapp.We have a 4 port channel group setup on our 3750x switch going to our netapp storage. We have a Wan 100mb link to our remote site and we want only 60MBs of that link to be used for Netapp traffic all other local traffic needs to use the full amount of the bandwidth to the netapp.
Is possible to allocate bandwidth in this way and how would I go about this? We dont have access to the routers for the link and they plug directly into a port on our cisco.
View 3 Replies
View Related
Mar 6, 2013
On my SUP-7E, when I issue a " show interface vlan X " I cannot see the expected input/rate reflecting the real rate (which should be very high).
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 4000 bits/sec, 2 packets/sec
(Under the physical interfaces it is ok)However on other SUP-IV I can see the real rate.
My questions are :
- Why the SUP-7E does not reflect the rate, whereas the SUP-IV does ?
- I have heard about the 'counter' command under the vlan interface to activate the rate counters. Is this command application has any side effect on the switch ?
View 2 Replies
View Related
Feb 25, 2013
If I have an interface configured as follows (on a Cisco 3750 Switch)
Interface gi 1/0/24
Bandwidth 100000
And then added the following command
srr-queue bandwidth limit 40
Would the result be 40% of the physical 1Gbps interface or 40% of the 100Mbps Bandwidth set under the interface bandwidth command.
View 2 Replies
View Related
Jul 29, 2012
In ASA 5510. How I can limit the users in (VLAN 20) to use the internet with a limited Bandwidth/speed with 3 mbps upload and 5 mbps download?
In case the outside interface (Native vlan) which is connected to the ISP and have a bandwidth/speed of 30 mbps upload and 50 mbps download.
View 4 Replies
View Related
