Cisco WAN :: 1841 Router - Limit Bandwidth With Priority For Voice?
Apr 22, 2011
We have some point-to-point sites linked with our HO with 10-30mbps speed. We have provided DID telephone lines to these sites as well.
We want to limit the bandwidth with 1mb bandwidth only and also make sure that the voice traffic (DID telephone lines) gets the priority over all other traffic even if they are utilitizing the 1mb link completely. We have some Cisco 1841 routers that we are planning to configure on the main uplink on each of these sites. how to give the priority to the voice traffic yet limiting the bandwidth to 1mb.
View 8 Replies
ADVERTISEMENT
Nov 29, 2011
We have 3 sets of applications. The first does not require much bandwidth but is very critical, the other two is more bandwidth consuming but less critical. I would like to know if it's possible to reflect this priorities on the router configuration. Is it possible to set the ports 10000, 10001 and 10002 of the external IP have higher priority to be handled, for example? Also, is it possible to limit the bandwidth that goes through a set of ports?
I must prevent the 2 sets of less critical applications to strugle the critical ones. What router can provide this capabilities? Is the 1921 able to do this job?
View 2 Replies
View Related
Nov 12, 2012
VLAN ===> FE 0/1 {With subinterfaces - ALL INSIDE LAN INTERFACES} ==> ROUTER ===> BVI 0/1 {WAN Interface - OUTSIDE}
i am doing NAT for my clients in LAN to WAN - Static NAT i want one of my client who is excessing some service with his Public IP to get a specific amount of bandwidth ... as right now he is hogging all the bandwidth .i have 1841 router.
View 7 Replies
View Related
Jun 21, 2012
we have a bandwidth pipe terminating on 1841 BVI interface... now we want to limit all the traffic going from inside to WAN circuit to half... for example 10 Mb pipe we want to reduce to 5 mb on bvi interface.. how this can be done .. as of not there is not need to police any specific type of traffic .. this needs to be done for any traffic from inside to outside...
View 1 Replies
View Related
Dec 6, 2010
I'm trying to configure QoS on my 877 router to give priority to voice packets. However, when I do a show policy-map for WAN interface, all the classes show 0 bps. When I do a show int for the WAN interface, I get the correct bandwidth util.
This 877 is meant for a home network. I'm running a Cisco 7970 phone using phone-proxy back to my HQ. I'm also shaping the traffic.
Here is my config
Class Map match-any EF (id 1)
Match ip precedence 5
Class Map match-any class-default (id 0)
Match any
View 5 Replies
View Related
Sep 10, 2012
I have about 4 different devices accessing the same network, which lags my pc gaming severely. I was wondering if there is a way to set my IP to the main priority. I am using a Westell 7500 router.
View 1 Replies
View Related
Oct 9, 2011
anyway to implement priority marking on the voice packets on the IP communcicator which installed in a laptop (running Data VLAN in the switch)?
View 1 Replies
View Related
Mar 7, 2013
Trying to set-up a priority queue for Voice and Video traffic, below is the current ASA config. The WAN link is 6mb, trying to limit the Internet traffic to 4mb and save 2mb for the PQ, config belowTraffic just isn't hitting the PQ
priority-queue outside
queue-limit 512
tx-ring-limit 200
!
class-map Video
description Video
match dscp af31
[code]....
View 6 Replies
View Related
Feb 11, 2013
I just wonder if there is simply way on Cisco 800 to set bandwidth priority for internal IP address. Basically I have server and would like to make sure, whatever comes to it or goes out has the highest priority and users won’t kill bandwidth for the server connection.
View 7 Replies
View Related
Jul 12, 2011
How can I limit the bandwidth of a router (DIR 600).
View 1 Replies
View Related
Mar 20, 2012
I currently have the following network structure, which work fine:
The only bandwidth management configuration I did in the Cisco E1000 router is to set the QOS, giving high priority to the 5 SIP Phones mac addresses.
The problem: I purchased a Small Business Cisco router RV016 because the company keep expanding so they will add more SIP Phones and PCs. In the new router configurations, there is no way to do like I did on the E1000 I just want to be able to set high priority to the SIP Phones mac addresses.
What happens when I use the new router (RV016) is that, sometime you dial a number and the phone do a busy signal and indicate "Call failed" or sometime people call in and there is only 3 phones ringing.
I tried port forwarding.. disabling firewall.. SPI.. I tried access rule.. whatever I do doesn't fix the issue.
When I put the Cisco E1000 back everything goes well.
I'm using the latest firmware: RV0XX-v4.1.1.01-sp.bin
View 6 Replies
View Related
Jun 11, 2011
I just purchased a 100M fiber line to go with a brand new D-Link DIR-655 router. Before plugging in the router, I tested on my laptop directly from the modem and had great result speeds of 98M/97M. I connected the router, then plugged my laptop to find I was only getting speeds of about 10M/6M. This was true for both wired and wireless connections.
I took a look at the router settings. I turned off QoS, but that didn't work. One thing I did see was the WAN was set to auto. I attempted to change that to 100mbps or to 1000mpbs. However, when I did that my modem light that shows a 100M connection is active turned off and I couldn't get internet. I was only able to get a connection if I left that on auto. Is there a setting somewhere that is limiting my bandwidth from the router?I reset the router twice and checked to find I had the latest firmware. Is there something that I am missing? I have always been a Linksys fan, but wanted to see how D-Link is.
View 7 Replies
View Related
May 21, 2012
I apologize in advance if this is a novice inquiry, but our company just switched from Point-to-Point T1's to Metro Ethernet.
On one point-to-point, from our main office to one of our high profile locations, we had two bonded T1's. Now this site has a 3 Mbps Metro-E link, but it's being over-saturated. I don't know what type of QOS implementation our T1 provider had, but it prevented flooding. Now, I'm getting horrendous latency as the office peak hours approach since there is no QOS on the mesh by our Metro-E providers.
Ultimately, my question is: what's the best way to set a Fast Ethernet port on a Cisco 1800 series router to limit all bandwidth to 3 Mbps? At the moment, I don't have a preference in which traffic takes priority. I tried the rate-limit command, along with a speed calculator I found online, but that slowed the network down immensely.
View 19 Replies
View Related
Oct 28, 2012
I am planning to buy a router for my hotel and I would like to know is it possible to limit the bandwidth limit to the guests? And the admin computer can utilize the maximum speed? it it possible to create a login page paper when some one enters my wifi connection?
View 7 Replies
View Related
Feb 7, 2013
Region : Spain
Model : TD-W8968
Hardware Version : V1
Firmware Version :
I have a TD-W8970. In settings "Bandwidth Manager" there is an option to put a value between 1 and 8, but does not specify which is better (1 or 8). What the value to give more priority to a computer to another?
View 1 Replies
View Related
Jul 6, 2012
I want to know how I can manually limit the Kbps for a particular devince in the QOS.I DO NOT want to simply set the priority (low/med/high). I want to "physically" limit a device.
When I select to do it manually (upstream bandwidth) it limits ALL devices and I do not want this. I want to limit the bandwidth on only one device that is connected (ie an Xbox)
I have a Linksys E4200 V2
View 9 Replies
View Related
May 12, 2013
I have 10Mbps internet speed connected to ciusco router 1841 that has 2 internal NICs. One NIC has a full 10Mbps download speed and the 2nd NIC is currently limited to 1Mbps download speed. I want to change the download speed of the 2nd NIC to 4Mbps? How do I do this on a cisco 1841 Router?
View 8 Replies
View Related
Mar 23, 2013
I have a task of setting up bandwidth limit on the 2811 router Fastethernet interfaces.The scenario is:We have a 4MB Internet connection and would like to allocate bandwidth usage to users.
Fastethernet 0/0 needs to be set with 256KB output and 2048 input. This is going to be connected to a wireless router. Fastethernet 0/1 needs to be configured with 2048 output.I could also use SDM if that's easier than using CLI.
View 2 Replies
View Related
Feb 22, 2013
I have a cisco 2821 router where as a cisco 2960 switch with connect on router as a trunk & one user vlan . this is my WAN router all traffic are internal . i have 2MB data connectivity on my WAN side. i have to Give a specific Bandwith on my SAP traffice . like when SAP traffice will come they all time get around 50 % bandwidth of my channel. If SAP resuest are not comming then other traffice will get full bandwith .
View 4 Replies
View Related
Mar 7, 2012
I got a 5MBps Lease Line Connection via FAST ETHERNET PORT. i got a Cisco 1841 Router.
I want to distribute bandwidth in this ratio 2MBps/2MBps/1MBps
2MBps = Office Connection
2MBps = Computer Laboratory Connection
1MBps = WIFI Connection
1841 has only 2 Fast Ethernet ports
so im planning to add up a 2modules of 2-Port Fast Ethernet High-Speed WIC for Cisco Integrated Services Routers
View 18 Replies
View Related
Jan 24, 2013
configuring a switch or a router to limit the bandwidth for a specific user/IP when need it. Most of my remote offices are configured like this:
Users ------ 3560 switch ------- 2801 router -------- T1 to NOC -------- 7204 router with channelized DS3
I use Netflow Analyzer for high bandwidth usage alerts and can see the user's IP right away when someone is clogging our T1s. My goal is to be able to temporarily limit the bandwidth of the user taking over the T1. Whatever is best switch config or on the router.
View 2 Replies
View Related
Jul 7, 2011
How can I limit bandwidth speed of guest accounts? Or are there free softwares available to do something like that? It's kinda like the hotspot softwares - where we can set hourly, daily, monthly allowances and see a report on their connectivity.
View 3 Replies
View Related
Feb 23, 2011
I have 3 sites. Each site has a Cisco 1841 as its WAN router with a 10Mb direct internet access circuit connected to Fa0/0. The sites are then connected to each other via site-to-site IPSEC VPN. (The LAN switches in use at each site are Cisco 3750 series) [code]
Now, Site A has already been set-up with VoIP telephony. The plan is to extend this to the other 2 offices.Auto QoS has been set-up on the switches and data and voice VLANs created in the same way for each office.
how should/do we extend the QoS for the voice over the WAN to ensure voice quality remains for site to site calls. And what special considerations do we have to make for it being IPSEC VPN connectivity between the sites? The actual IP telephony system itself is being set-up by a 3rd party and not a lot of information on their requirements has been forthcoming so far – essentially all we have really been told is that they would like us to “reserve” a certain amount of bandwidth for the voice traffic between each site.
View 3 Replies
View Related
May 2, 2012
I am a Network admin of 200 Computers.Most of our users used to download movies through torrents.I just want to now how can i limit the bandwidth for specific user for both domain and work group user
View 4 Replies
View Related
May 11, 2012
Is there a way to limit a whole PC windows XP, or a certain program to use only a certain about of your total internet connection bandwidth?For example, I have 5 PCs in home all one the same ISP connection. I have one PC that I am trying to backup files online but I can only run it at certain times due to the backup program using ALL upload/download speed. And that makes every other PC super slow.
View 3 Replies
View Related
Dec 2, 2011
If a person downloads via ADSL2 5 GB how much bandwith would this require?
View 1 Replies
View Related
Aug 18, 2011
I am using ASA 5505 cisco firewall as a transparent firewall. I have assigned ethernet 0/0 as outside interface and ethernet0/1-7 as inside interface. There are 3 departments in office. So, i connected ethernet 0/1 to Dept A, ethernet 0/2 to Dept B and ethernet 0/3 to Dept C. Now, I want to limit bandwidth to each department, e.g, 1 Mbps download/upload to Dept A, 512 kbps download/upload to Dept B and 512 kbps download/upload to Dept C. So, how can i do this in ASA 5505.?
View 1 Replies
View Related
Feb 25, 2012
If two (one 6509A 9/26 with server A located in A end, 6509B with serverB located in B End) which is connected via a 1G link. If there is serverA send 700M file to server B via a 1G link. If I configured below command to 6509A 9/26, can I limit the bandwidth of server on bothincoming and outgoing to 500M?
class-map match-all FROM-SERVERmatch access-group name FROM-SERVER!policy-map FROM-SERVERclass FROM-SERVERpolice 500000000 conform-action transmit exceed-action drop!interface GigabitEthernet9/26service-policy in FROM-SERVER
View 1 Replies
View Related
Feb 6, 2012
I have a 3845 Router with three connected interfaces, one to my WAN, one to my LAN and another to my wifi zone. I want to limit the amount of WAN bandwidth the WIFI zone can take to say a max of one third and not restrict WAN bandwidth from the LAN at all.
View 7 Replies
View Related
Apr 29, 2012
I have cisco 7600 core router in ISP , i want to put the bandwidth limit on it for outgoing traffic (for internet) on a subnet because i am using Bluecoat and i want to test my bluecoat.On this subnet i have no limit for bluecoat but after the bluecoat i want to limit it. On 7600 cisco router i have not rate limit command so how it can be possible for a perticular subnet ?
View 1 Replies
View Related
Feb 10, 2012
I have two vlan interfaces, how to limit bandwidth on them ?I need than speed on each will be direrent.
View 1 Replies
View Related
Dec 31, 2011
I want to switch to a slower ISP because of financial constraints (specifically downgrade from cable to DSL), so I'd like to set up my Windows XP computer so that it downloads and uploads at the same speed that the slower ISP does. That way I can kind of "try before I buy" for a week or so, to get an idea if I can live with the slower speed before disconnecting from cable and incurring a disconnect charge. I was told that some software that limits your bandwidth also may cause distortion in video or audio streams, so I'd like to avoid that.
View 2 Replies
View Related
May 1, 2011
My router is a GT704-WG running on the default firmware. I need to limit a certain computer's bandwidth. Am I able to set the maximum download/upload speed for a certain computer via the router control panel (192.168.1.1)?
View 11 Replies
View Related
