Cisco WAN :: 1921 - Traffic Control / Packet Priority And Bandwidth Limit
Nov 29, 2011
We have 3 sets of applications. The first does not require much bandwidth but is very critical, the other two is more bandwidth consuming but less critical. I would like to know if it's possible to reflect this priorities on the router configuration. Is it possible to set the ports 10000, 10001 and 10002 of the external IP have higher priority to be handled, for example? Also, is it possible to limit the bandwidth that goes through a set of ports?
I must prevent the 2 sets of less critical applications to strugle the critical ones. What router can provide this capabilities? Is the 1921 able to do this job?
View 2 Replies
ADVERTISEMENT
Feb 7, 2013
Region : Spain
Model : TD-W8968
Hardware Version : V1
Firmware Version :
I have a TD-W8970. In settings "Bandwidth Manager" there is an option to put a value between 1 and 8, but does not specify which is better (1 or 8). What the value to give more priority to a computer to another?
View 1 Replies
View Related
Apr 22, 2011
We have some point-to-point sites linked with our HO with 10-30mbps speed. We have provided DID telephone lines to these sites as well.
We want to limit the bandwidth with 1mb bandwidth only and also make sure that the voice traffic (DID telephone lines) gets the priority over all other traffic even if they are utilitizing the 1mb link completely. We have some Cisco 1841 routers that we are planning to configure on the main uplink on each of these sites. how to give the priority to the voice traffic yet limiting the bandwidth to 1mb.
View 8 Replies
View Related
Aug 22, 2011
We are about to share a 10 MBit ISP connection with 2 others companies, and they are going to split the bill up into 3,3 and 4 Mbit, so we where thinking that we could setup a switch before their and ours router and provide them with a static IP from our ISP. But is it possible to set a bandwidth limit on the ports of a Cisco Catalyst 2960-8TC, so that we can set a limit of 3,3 and 4 on 3 ports.
View 1 Replies
View Related
Nov 5, 2012
We run a workers camp here and we currently have around 2500-3000 people using our 100MB internet pipe. We are upgrading the pipe to 200MB soon but I still would like to limit how much bandwidth everyone is using.
We allow streaming media such as Netflix, youtube, apple TV and of course .So it gets full pretty fast. We have QOS implemented although I wasn't here when it was done so I don't know a lot about it. I would like to limit IPs to a certain amount of bandwidth. [code]
View 1 Replies
View Related
Jul 15, 2009
I use WS-C3560G-24TS and try both ios 12.2.50.SE1 and 12.2.46.SE but problem the same. The config as following,
interface GigabitEthernet0/1
no switchport
ip address 1.1.1.2 255.255.255.0
[code].....
but I find the int g0/1 output traffic only can achieve about 500kbps then I try config below,
interface GigabitEthernet0/1
no switchport
[code]....
I find int g0/1 output traffic only can achieve about 5Mbps,but if I change "srr-queue bandwidth limit xx" command xx to 20-90,the int g0/1 can achieve normal traffic bps, for example,
interface GigabitEthernet0/1
no switchport
[code]...
the int g0/1 output can achieve 2Mbps that is correct,just only when limit set to 10%,the traffic only can achieve half of limit bandwidth.
View 5 Replies
View Related
Oct 25, 2012
I am fairly new to Cisco, but am trying to configure a 1921 router to give higher priority to SIP/VoIP traffic (Port 5060) than everything else.The connection is only 4Mb and is getting hit hard by video streaming, I don't want to block this, just make a lower priority.Any ideas where I am going wrong?My current config is as below.The IP addresses have been changed for security reasons, but in reality are both in the same range, i.e. are both external IPs, so I am not sure if this is causing the problem. Do I need NAT for QoS to work?
View 6 Replies
View Related
Apr 24, 2012
Our company had been buying Cisco 1841 routers for years and they have served us well. The 1841 was discontinued and instead we have now purchased a Cisco 1921. It is brand new, running "Version 15.0(1r)M15" of IOS ("usbflash0:c1900-universalk9-mz.SPA.151-4.M4.bin" file).
On our older Cisco 1841 routers, we would always prioritize certain TCP and UDP packets using the priority-list command. However, I have suddenly discovered that priority-list is not available on this brand new router. (?) I am unsure why. I did some reading and according to the document [URL], and priority-group are unsupported in Cisco IOS 15.
Later version of a product isn't as fully-featured as the earlier version. I want to prioritize the following type of network traffic.
UDP ports 8000 through 8063, 2427, 2727, 9300, 9301
TCP port 35300, 60001 through 60010, 2065, 33333, 3065
giving them a higher priority than the rest of other packets. This is necessary for our vendor's VoIP implementation. These packets should be "high" priority; everything else can be "medium."
View 3 Replies
View Related
Feb 12, 2013
When I ping my video streaming host's IP address (the IP that they gave me where I can view my IP web camera's video stream), I get anywhere from 0% to 8% packet loss at various times of the day. They're claiming that there's no problem, that this is because this is a router and it's dropping ping packets due to "ping priority giving preference to more important network traffic."
View 7 Replies
View Related
Feb 11, 2013
I just wonder if there is simply way on Cisco 800 to set bandwidth priority for internal IP address. Basically I have server and would like to make sure, whatever comes to it or goes out has the highest priority and users won’t kill bandwidth for the server connection.
View 7 Replies
View Related
Mar 20, 2012
I currently have the following network structure, which work fine:
The only bandwidth management configuration I did in the Cisco E1000 router is to set the QOS, giving high priority to the 5 SIP Phones mac addresses.
The problem: I purchased a Small Business Cisco router RV016 because the company keep expanding so they will add more SIP Phones and PCs. In the new router configurations, there is no way to do like I did on the E1000 I just want to be able to set high priority to the SIP Phones mac addresses.
What happens when I use the new router (RV016) is that, sometime you dial a number and the phone do a busy signal and indicate "Call failed" or sometime people call in and there is only 3 phones ringing.
I tried port forwarding.. disabling firewall.. SPI.. I tried access rule.. whatever I do doesn't fix the issue.
When I put the Cisco E1000 back everything goes well.
I'm using the latest firmware: RV0XX-v4.1.1.01-sp.bin
View 6 Replies
View Related
Sep 10, 2012
I have about 4 different devices accessing the same network, which lags my pc gaming severely. I was wondering if there is a way to set my IP to the main priority. I am using a Westell 7500 router.
View 1 Replies
View Related
Oct 28, 2012
I am planning to buy a router for my hotel and I would like to know is it possible to limit the bandwidth limit to the guests? And the admin computer can utilize the maximum speed? it it possible to create a login page paper when some one enters my wifi connection?
View 7 Replies
View Related
Oct 14, 2012
I wan to ask whether i can control and limit my internet speed on LAN or not cos nowadays i have internet shop, but i couldn't control download bandwidth of each customer who come to download. Sometimes, it's effected to other customer using internet too,
View 1 Replies
View Related
Jan 24, 2012
In QoS, voice traffic is usually marked EF and placed in a priority queue. But interactive video traffic, like VTC, should also receive priority treatment. Can I put both classes in their own priority queues in the same policy map? I thought there could only be one LLQ, but I'm not sure about it. An example of the config I'm thinking of is below. Voice would be marked EF, VTC would be marked AF41.
View 6 Replies
View Related
Nov 27, 2012
I am testing limit bandwith using my ASA 8.2, i am trying to limit internet access for certains users , i order to save Bandwith for the important things but i can´t get any limitation
My configuration is the following, the acces list is just for my pc in order to test, and the service policy is applied to outside interface (called internet in my case) for incoming traffic
access-list Internet_mpc_1 extended permit ip host 172.16.127.70 any class-map Internet-class-TEST match access-list Internet_mpc_1 policy-map Internet-policy-web class Internet-class-TEST police output 1024000 1500
service-policy Internet-policy-web interface Internet
With show service policy i can´t see any activity on the policy , but if i do a similar configuration for inside interface outgoing traffic i can see packets allowed and dropped
View 3 Replies
View Related
Jun 30, 2010
I have several computers connected to the network, can I restrict the download bandwidth on specific computer?
View 3 Replies
View Related
Mar 7, 2013
Trying to set-up a priority queue for Voice and Video traffic, below is the current ASA config. The WAN link is 6mb, trying to limit the Internet traffic to 4mb and save 2mb for the PQ, config belowTraffic just isn't hitting the PQ
priority-queue outside
queue-limit 512
tx-ring-limit 200
!
class-map Video
description Video
match dscp af31
[code]....
View 6 Replies
View Related
Nov 19, 2012
i have a 3560 connecting to a sp with limited bandwidth. i have one interface on the switch whose traffic i do not want to drop. i want this traffic to go into the high priority queue. i am not sure how this should be configured, but here is my best guess and my current qos configuration on the switch:
qos map cos-dscp 0 8 16 26 32 46 48 56
mls qos srr-queue output cos-map queue 1 threshold 3 5
mls qos srr-queue output cos-map queue 2 threshold 1 4 6 7
mls qos srr-queue output cos-map queue 2 threshold 2 3(code)
since cos 5 is mapped to dscp 46 then this traffic would go into the priority queue. is this correct ?
View 7 Replies
View Related
May 2, 2012
I am a Network admin of 200 Computers.Most of our users used to download movies through torrents.I just want to now how can i limit the bandwidth for specific user for both domain and work group user
View 4 Replies
View Related
May 11, 2012
Is there a way to limit a whole PC windows XP, or a certain program to use only a certain about of your total internet connection bandwidth?For example, I have 5 PCs in home all one the same ISP connection. I have one PC that I am trying to backup files online but I can only run it at certain times due to the backup program using ALL upload/download speed. And that makes every other PC super slow.
View 3 Replies
View Related
Dec 2, 2011
If a person downloads via ADSL2 5 GB how much bandwith would this require?
View 1 Replies
View Related
Mar 24, 2005
i have a 3550 catalyst and i configured it for bandwidth controlling i have used POLICE command its work fine and i saw it limit the bandwidth but there is a little problem when i limit the bandwidth at 1024000 and i useing all the bandwidth and monitor the bandwidth i see it shows the network uses half bandwidth.
View 6 Replies
View Related
Aug 14, 2011
I want to control bandwidth of our computers in network. We are using TPLINK routers. I already done ipqos setting in the main router but it doesn't really effective. I also tried ipqos in the routers(which is used as WAP) but it also not effective.
View 8 Replies
View Related
Oct 20, 2011
I have the following setup:
Cisco 1921 is my core router and connected to it is a 30 Mbit fiberline
VLAN1
VLAN2
Now, the thing is that i want VLAN2 to have a 5 Mbit bandwidth limit to Internet but full speed to VLAN1.
I have played around with Rate limit without success.
I also have access to cisco switches that can limit the bandwidth.
View 23 Replies
View Related
Aug 18, 2011
I am using ASA 5505 cisco firewall as a transparent firewall. I have assigned ethernet 0/0 as outside interface and ethernet0/1-7 as inside interface. There are 3 departments in office. So, i connected ethernet 0/1 to Dept A, ethernet 0/2 to Dept B and ethernet 0/3 to Dept C. Now, I want to limit bandwidth to each department, e.g, 1 Mbps download/upload to Dept A, 512 kbps download/upload to Dept B and 512 kbps download/upload to Dept C. So, how can i do this in ASA 5505.?
View 1 Replies
View Related
Feb 25, 2012
If two (one 6509A 9/26 with server A located in A end, 6509B with serverB located in B End) which is connected via a 1G link. If there is serverA send 700M file to server B via a 1G link. If I configured below command to 6509A 9/26, can I limit the bandwidth of server on bothincoming and outgoing to 500M?
class-map match-all FROM-SERVERmatch access-group name FROM-SERVER!policy-map FROM-SERVERclass FROM-SERVERpolice 500000000 conform-action transmit exceed-action drop!interface GigabitEthernet9/26service-policy in FROM-SERVER
View 1 Replies
View Related
Feb 6, 2012
I have a 3845 Router with three connected interfaces, one to my WAN, one to my LAN and another to my wifi zone. I want to limit the amount of WAN bandwidth the WIFI zone can take to say a max of one third and not restrict WAN bandwidth from the LAN at all.
View 7 Replies
View Related
Apr 29, 2012
I have cisco 7600 core router in ISP , i want to put the bandwidth limit on it for outgoing traffic (for internet) on a subnet because i am using Bluecoat and i want to test my bluecoat.On this subnet i have no limit for bluecoat but after the bluecoat i want to limit it. On 7600 cisco router i have not rate limit command so how it can be possible for a perticular subnet ?
View 1 Replies
View Related
Feb 10, 2012
I have two vlan interfaces, how to limit bandwidth on them ?I need than speed on each will be direrent.
View 1 Replies
View Related
Nov 12, 2012
VLAN ===> FE 0/1 {With subinterfaces - ALL INSIDE LAN INTERFACES} ==> ROUTER ===> BVI 0/1 {WAN Interface - OUTSIDE}
i am doing NAT for my clients in LAN to WAN - Static NAT i want one of my client who is excessing some service with his Public IP to get a specific amount of bandwidth ... as right now he is hogging all the bandwidth .i have 1841 router.
View 7 Replies
View Related
Dec 31, 2011
I want to switch to a slower ISP because of financial constraints (specifically downgrade from cable to DSL), so I'd like to set up my Windows XP computer so that it downloads and uploads at the same speed that the slower ISP does. That way I can kind of "try before I buy" for a week or so, to get an idea if I can live with the slower speed before disconnecting from cable and incurring a disconnect charge. I was told that some software that limits your bandwidth also may cause distortion in video or audio streams, so I'd like to avoid that.
View 2 Replies
View Related
May 1, 2011
My router is a GT704-WG running on the default firmware. I need to limit a certain computer's bandwidth. Am I able to set the maximum download/upload speed for a certain computer via the router control panel (192.168.1.1)?
View 11 Replies
View Related
