D-Link DIR-655 :: Settings To Limit Bandwidth From Router?
Jun 11, 2011
I just purchased a 100M fiber line to go with a brand new D-Link DIR-655 router. Before plugging in the router, I tested on my laptop directly from the modem and had great result speeds of 98M/97M. I connected the router, then plugged my laptop to find I was only getting speeds of about 10M/6M. This was true for both wired and wireless connections.
I took a look at the router settings. I turned off QoS, but that didn't work. One thing I did see was the WAN was set to auto. I attempted to change that to 100mbps or to 1000mpbs. However, when I did that my modem light that shows a 100M connection is active turned off and I couldn't get internet. I was only able to get a connection if I left that on auto. Is there a setting somewhere that is limiting my bandwidth from the router?I reset the router twice and checked to find I had the latest firmware. Is there something that I am missing? I have always been a Linksys fan, but wanted to see how D-Link is.
I am planning to buy a router for my hotel and I would like to know is it possible to limit the bandwidth limit to the guests? And the admin computer can utilize the maximum speed? it it possible to create a login page paper when some one enters my wifi connection?
I apologize in advance if this is a novice inquiry, but our company just switched from Point-to-Point T1's to Metro Ethernet.
On one point-to-point, from our main office to one of our high profile locations, we had two bonded T1's. Now this site has a 3 Mbps Metro-E link, but it's being over-saturated. I don't know what type of QOS implementation our T1 provider had, but it prevented flooding. Now, I'm getting horrendous latency as the office peak hours approach since there is no QOS on the mesh by our Metro-E providers.
Ultimately, my question is: what's the best way to set a Fast Ethernet port on a Cisco 1800 series router to limit all bandwidth to 3 Mbps? At the moment, I don't have a preference in which traffic takes priority. I tried the rate-limit command, along with a speed calculator I found online, but that slowed the network down immensely.
I want to know how I can manually limit the Kbps for a particular devince in the QOS.I DO NOT want to simply set the priority (low/med/high). I want to "physically" limit a device.
When I select to do it manually (upstream bandwidth) it limits ALL devices and I do not want this. I want to limit the bandwidth on only one device that is connected (ie an Xbox)
We have some point-to-point sites linked with our HO with 10-30mbps speed. We have provided DID telephone lines to these sites as well.
We want to limit the bandwidth with 1mb bandwidth only and also make sure that the voice traffic (DID telephone lines) gets the priority over all other traffic even if they are utilitizing the 1mb link completely. We have some Cisco 1841 routers that we are planning to configure on the main uplink on each of these sites. how to give the priority to the voice traffic yet limiting the bandwidth to 1mb.
How can I limit bandwidth speed of guest accounts? Or are there free softwares available to do something like that? It's kinda like the hotspot softwares - where we can set hourly, daily, monthly allowances and see a report on their connectivity.
I have a task of setting up bandwidth limit on the 2811 router Fastethernet interfaces.The scenario is:We have a 4MB Internet connection and would like to allocate bandwidth usage to users.
Fastethernet 0/0 needs to be set with 256KB output and 2048 input. This is going to be connected to a wireless router. Fastethernet 0/1 needs to be configured with 2048 output.I could also use SDM if that's easier than using CLI.
I have a cisco 2821 router where as a cisco 2960 switch with connect on router as a trunk & one user vlan . this is my WAN router all traffic are internal . i have 2MB data connectivity on my WAN side. i have to Give a specific Bandwith on my SAP traffice . like when SAP traffice will come they all time get around 50 % bandwidth of my channel. If SAP resuest are not comming then other traffice will get full bandwith .
configuring a switch or a router to limit the bandwidth for a specific user/IP when need it. Most of my remote offices are configured like this:
Users ------ 3560 switch ------- 2801 router -------- T1 to NOC -------- 7204 router with channelized DS3
I use Netflow Analyzer for high bandwidth usage alerts and can see the user's IP right away when someone is clogging our T1s. My goal is to be able to temporarily limit the bandwidth of the user taking over the T1. Whatever is best switch config or on the router.
So my ISP (Telus) recently replaced our old router with a ZyXEL VSG1432. I'm currently having a huge lag issue when my roommates laptop is connected to our network. He is connected via wireless, I'm wired. So I did some searching around and I think i can solve this by limiting his bandwidth with QoS settings. I'm getting conflicting information here though. After logging into the router there are no QoS options yet according to ZyXEL's website url...This router should have the settings available. Is it possible that Telus does something to remove this feature? Is there some not so obvious way to enable QoS? Is there some other way to limit the bandwidth?
I just bought a Linksys E4500. I would like some support to configure the settings regarding the 5 Ghz Bandwidth.I need to fill out the cells for Server Radius IP and port.Which are the best setting for this section?
I am a Network admin of 200 Computers.Most of our users used to download movies through torrents.I just want to now how can i limit the bandwidth for specific user for both domain and work group user
Is there a way to limit a whole PC windows XP, or a certain program to use only a certain about of your total internet connection bandwidth?For example, I have 5 PCs in home all one the same ISP connection. I have one PC that I am trying to backup files online but I can only run it at certain times due to the backup program using ALL upload/download speed. And that makes every other PC super slow.
I want to switch to a slower ISP because of financial constraints (specifically downgrade from cable to DSL), so I'd like to set up my Windows XP computer so that it downloads and uploads at the same speed that the slower ISP does. That way I can kind of "try before I buy" for a week or so, to get an idea if I can live with the slower speed before disconnecting from cable and incurring a disconnect charge. I was told that some software that limits your bandwidth also may cause distortion in video or audio streams, so I'd like to avoid that.
My router is a GT704-WG running on the default firmware. I need to limit a certain computer's bandwidth. Am I able to set the maximum download/upload speed for a certain computer via the router control panel (192.168.1.1)?
On my home network I have 11 devices connected.Is there a way I can give each device a certain bandwidth limit so my Internet doesn't keep getting sucked up?
I am using ASA 5505 cisco firewall as a transparent firewall. I have assigned ethernet 0/0 as outside interface and ethernet0/1-7 as inside interface. There are 3 departments in office. So, i connected ethernet 0/1 to Dept A, ethernet 0/2 to Dept B and ethernet 0/3 to Dept C. Now, I want to limit bandwidth to each department, e.g, 1 Mbps download/upload to Dept A, 512 kbps download/upload to Dept B and 512 kbps download/upload to Dept C. So, how can i do this in ASA 5505.?
I currently have a 20mb connection with sky. I have 4 computers in my household and using the wireless modem router to distribute the connection.can I limit each computer to a certain amount of bandwidth. (eg PC1 =5mb, PC2=5mb, PC3=5mb, PC4=5mb) Two of my computers are running Win Vista HP and two computers are running Win 7 Pro & Ultimate.
I have a roommate who takes up a lot of bandwidth from the internet. I am allowing him to use my router which is a Linksys E2500. Is there anyway to limit how much bandwidth he can actually use.
If two (one 6509A 9/26 with server A located in A end, 6509B with serverB located in B End) which is connected via a 1G link. If there is serverA send 700M file to server B via a 1G link. If I configured below command to 6509A 9/26, can I limit the bandwidth of server on bothincoming and outgoing to 500M?
class-map match-all FROM-SERVERmatch access-group name FROM-SERVER!policy-map FROM-SERVERclass FROM-SERVERpolice 500000000 conform-action transmit exceed-action drop!interface GigabitEthernet9/26service-policy in FROM-SERVER
I have a 3845 Router with three connected interfaces, one to my WAN, one to my LAN and another to my wifi zone. I want to limit the amount of WAN bandwidth the WIFI zone can take to say a max of one third and not restrict WAN bandwidth from the LAN at all.
I have cisco 7600 core router in ISP , i want to put the bandwidth limit on it for outgoing traffic (for internet) on a subnet because i am using Bluecoat and i want to test my bluecoat.On this subnet i have no limit for bluecoat but after the bluecoat i want to limit it. On 7600 cisco router i have not rate limit command so how it can be possible for a perticular subnet ?
I have a 20MB internet connection, with a 100GB cap. My mother works at home, with some employees. Adding home and work, 8 people use the internet all the time. Lots of Youtube videos, streaming netflix, iTunes downloading, and so on.I wanted something to:
1) Manage this cap. It's over too soon, and we're left with a poor internet connection until the end of the month - like 500kb.
2) Something to manage two internet connections.
I was thinking about a dedicated router - I currently use a WRT54G V8, which is nice, but it has some issues handling the traffic when the internet is in its full glory. I heard about pfSense, and some searches on Google tell me it's possible to do both options using it.
VLAN ===> FE 0/1 {With subinterfaces - ALL INSIDE LAN INTERFACES} ==> ROUTER ===> BVI 0/1 {WAN Interface - OUTSIDE}
i am doing NAT for my clients in LAN to WAN - Static NAT i want one of my client who is excessing some service with his Public IP to get a specific amount of bandwidth ... as right now he is hogging all the bandwidth .i have 1841 router.
Anyway, I have a cable connection with a modem and a D-Link wireless router. Some of the users are abusing the bandwidth, making it difficult for others to surf the net.What's the easiest way to set a bandwidth limit for each user? Also, it is possible to do it through the router as I don't want to keep my computer running the whole time?
Been looking around in my routers settings for something that even comes close to limiting bandwidth on a specific port, or mac address, but the only thing I can find is priority settings like "Low, Normal, High, and Highest" I did however see this:
I am not 100% sure if I can specifically set bandwidth limit per port or mac address, cause I don't see an option to do that, so I presume it just limits the whole network as one...
The rest of us use wifi for our internet services but this isn't good enough for are newest member so they have now connected a cable directly into the modem, so now whenever he is online ALL wifi suffers dramatically! What can i do to limit his bandwidth and allow the wifi to gain more access is there a way to limit via his MAC address or IP address?
