I just bought a Linksys E4500. I would like some support to configure the settings regarding the 5 Ghz Bandwidth.I need to fill out the cells for Server Radius IP and port.Which are the best setting for this section?
View 3 RepliesHow to configure settings for E4200
View 1 Replies View RelatedAfter a successful firmware update to my router I can’t configure wireless settings because the .htm page stays blank if I back the page it comes back to setup page but any config page shows blank with no error message. I’m on a win8 64 iexplorer 10, also tried on a win7 32 IE 8,9,10.
View 1 Replies View RelatedDo you know when will be possible to manual configure ipv6 settings? I have all parameters from my ISP but the settings on the router are only automatic and 6rd. Is it possible to enable this in future firmwares?
View 1 Replies View RelatedSince the upgrade by Cisco I can only see Win7 PC's on the network. I can not see the USB drive attached to the E4500, nor can I see my Media server which is Linux based nor any Win XP computuers.
View 9 Replies View RelatedE4500 local network IP is 10.10.XXX.XXX and the DHCP server also starts with this subnet. My network is 192.168.XXX.XXX based but if I manually chahge the routers IP I can no longer access it. I do not use DHCP as this is in bridge mode. Why is this setup this way...CCC?
View 1 Replies View RelatedI just got a new E4500 and plugged a blank 2TB drive into it (Windows shows it is formatted NTFS) which was originally plugged into my WRT-610. I'm moving my media files and when it hits a 50+GB video it reports that there is not enough space to move the file. Smaller files are moving just fine.
View 4 Replies View RelatedI see I have 2.1.39.144146 but I don't see that version on the download page?
View 3 Replies View Relatedi sold off my e4200 & brought a e4500 .The e4200 has had a 2 TB W.D external drive attached ,i stream movies to a sat pvr in the .ts format .The problem is i set the e4500 up & it deleted my .ts files not once but 3 times.when i brought the e4500 i did roll the firmware back to the classic non cloud firmware.the third time i had turned the router off & once swtiched back on my files were gone .should i safely remove the drive from the set up ? what if i have a power failure?
View 5 Replies View RelatedMy e4500 seems to be blocking my nhl gamecenter apps from playing live video on Ipad and I phones..nhl support tells me it is setting in router.?
View 6 Replies View RelatedI have linksys E4500 and I would like to be able to see the website visited vs ip address.Is there a way to enable same or achive same via parental controls.Again I do not want to block a website but monitor which websites are visited. Is this achievable via router or an additional software/hardware required to be used with router
View 5 Replies View RelatedNot sure if I have a defective router, but if I unplug it I then need to wait at least a half hour to plug it back in. Anytime sooner and it won't broadcast a SSID or connect to the modem. This is a huge inconvenience if you want to change router settings and then you need to restart.
View 1 Replies View RelatedLatest firmware with CCC corrupted after power outage. I reseet the e4500 several times and tried to reload the firmware and still no good. Only way I got it back up is to install the older non-CCC version 2.37. Strange all was fine until the power outage. Not sure if I should even bother to upgrade to 2.38 again.
View 2 Replies View RelatedJust purchased the E4500 today and install failed on both machines. Install starts and then fails to finish.I have contacted support via chat and was given manual instructions and the router will not connect to either machine.Are there known issues with the Cisco Connect software not installing?
The chat support person finally dropped out of the chat and the router remains in an unusable state.I currently had to cable wired connection of laptop to get an internet connection.
due to location issues, I have to use the E4500 as a 2nd router. I have a Netgear router setup as the primary router connected to the internet, this acts as my firewall. The E4500 connected to the netgear and it route all traffic fine. The only issue I have is port forwarding to E4500. I've setup the FTP server on the E4500 and can access it via the internal network. Then on the netgear I forward the FTP port 21to the E4500. But it doesn't seem to work.
I know when I forward all my other ports, it works just fine. If I setup a FTP server on an other machine and forward that the port it works, just not the E4500. I've disabled all firewall settings on the E4500, and still nothing.
I just purchased a 100M fiber line to go with a brand new D-Link DIR-655 router. Before plugging in the router, I tested on my laptop directly from the modem and had great result speeds of 98M/97M. I connected the router, then plugged my laptop to find I was only getting speeds of about 10M/6M. This was true for both wired and wireless connections.
I took a look at the router settings. I turned off QoS, but that didn't work. One thing I did see was the WAN was set to auto. I attempted to change that to 100mbps or to 1000mpbs. However, when I did that my modem light that shows a 100M connection is active turned off and I couldn't get internet. I was only able to get a connection if I left that on auto. Is there a setting somewhere that is limiting my bandwidth from the router?I reset the router twice and checked to find I had the latest firmware. Is there something that I am missing? I have always been a Linksys fan, but wanted to see how D-Link is.
So my ISP (Telus) recently replaced our old router with a ZyXEL VSG1432. I'm currently having a huge lag issue when my roommates laptop is connected to our network. He is connected via wireless, I'm wired. So I did some searching around and I think i can solve this by limiting his bandwidth with QoS settings. I'm getting conflicting information here though. After logging into the router there are no QoS options yet according to ZyXEL's website url...This router should have the settings available. Is it possible that Telus does something to remove this feature? Is there some not so obvious way to enable QoS? Is there some other way to limit the bandwidth?
View 1 Replies View RelatedIm using a Linksys E4500 wireless router behind a Motorola SB6121 modem. My OS is Windows 7 and it is fully up to date. In general my entire network is working well. Now I have purchased a new IP surveillance camera and need to forward a port to be able to have remote viewing of the camera. Mi ISP blocks quite a few inbound ports including 80 so I have been trying a lot of ports all over the map to find something that will allow inbound access.
After several hours, nothing I have tried works, using a couple of different port probes including one called CanYouSeeMe I always get a "timed out" message. I have disabled the firewall in the router and on the local computer and still no luck. This says to me that either Cox is blocking nearly all ports (doubtful) or the modem is blocking access to the router somehow.
The Surfboard modem doesn't have a built in router. Unfortunately I don't have an old working modem to put in the circuit.
I don't guess it matters but the camera is accessible from all other local computers on the LAN using its IP address with a port number appended (right now it's using 8000).
I have windows vista, and forgot my network password. I reset my router to factory settings by pushing the reset button on the back.I tried reconfiguring the router from the network icon, but at the end of the process it says it cannot configure my router.I lost my internet service in the process
View 1 Replies View RelatedI just installed Windows XP Professional on my Toshiba-X205 laptop and I am having a problem getting the OS to detect my NIC. I can not remember how to go into the control panel and configure settings so the OS will detect my wireless network or should i say i can not get my OS to detect my NIC so i can to connect to my wireless network. I think i may need to install the device driver for the NIC but i don't remember which driver i need for the NIC of my laptop and i can not find it on the Toshiba website, not supported anymore.
View 1 Replies View Relatedi recently had att u vesre installed at my house with a 2 wire 3801 router/ modem but i cant get my xbox 360 online. how to configure the router for the xbox 360 so i can play xbox live.
View 1 Replies View RelatedI have configured a few 3750G switches with trunks and I want to test the throughput. In your experience is iperf the best tool? If so what settings do you use?
View 5 Replies View RelatedI have a E4200 router v.01 and when i updated the latest firmware (due to security exploit) it seems that whenever i acess the router settings (192.168.1.1) it doesn't ask me nor to input the admin and the password anymore, using wifi or wired.. I want the usual proccess whenever i go to 192.168.1.1 it will ask me to input my admin and password to change my router settings..
View 4 Replies View RelatedI would love to see this added in a future firmware release. I imagine others would welcome it as well that have caps with their isp.
View 9 Replies View RelatedE4200 V1 QOS can add downlink bandwidth？
View 3 Replies View RelatedTelefonica router (this my internet provider) --> WRT12N --wireless/eth--> my laptop
With that configuration I get a 1Mbps band with But in this configuration Telefonica router (this my internet provider) -- wireless/eth--> my lapto I get 7Mbps.Using always the same port of my telefonica router.Why the WRT120N is not providing the whole bandwidth? Is there any option in the router that divide the whole bandwith (7Mbps, almost 8Mbps) among the four ports of the wrt120n (giving 1Mbps per port)
I changed the router's IP to 192.168.2.1 due to the same situation as this [URL] linksys and now I can't access my settings I have tried the both pips and nothing and I can't seem to get my linksys wrt54gs v7.2 to let two computers be on the internet at the same time both can be on the network but on one on the internet
View 6 Replies View RelatedA few months ago I purchased an e2500 Cisco Linksys router to use in my home. This past Christmas, my family got about 4 new wifi devices which they added to the network bringing the total number of devices on my home network to 10. I wanted to know if there are any advanced settings in Cisco Connect that I can tweak to make my wifi speeds faster because right now I'm getting about 55 Mbps on most of my devices. I was also wondering what the typical range of the e2500 router was and if the e4200 offers a large improvement.
View 3 Replies View RelatedManually type http://192.168.1.1/Wireless_Advanced.asp and the Advanced Wireless Settings tab appears! (I found this info in dd-wrt forum). A lot more settings to play with here, including transmission power for both 5GHz and 2.4GHz.
View 3 Replies View RelatedI have linksys WRT54GH wireless router with me.I want to know how can i connect it with any other wireless router. What settings do i need to change.
View 1 Replies View Relatedhow to set up my router settings/port forwarding to be able to use Wake on Lan with Depicus here is what I currently have:DHCP Reservation with the IP Address of my computer (192.168.1.xxx) and the MAC address xx:xx:xx:xx that I retrieved by doing ipconfig /all in the cmdMy Router address is 192.168.1.1 and the submnet mask is 255.255.255.0my DDNS service is disabledIn the Security tab, I unchecked Filter anonymous internet requestsIn Applications and Gaming, under single port forwarding, I have port 7 to 7, Both TCP and UDP, forwarded to the IP address of my computer 192.168.1.xxx and it is enabledMy network card is configured already, enabling WOL in the card's properties.Now when I use Depicus, I enter the MAC, my external IP address which I got from myipaddress.com, subnet mask I use 255.255.255.0, I select Internet, and then the remote port I use is 7,Doing that, nothing happens at all. however, I can easily wake up my computer if I am connected to the same local network at home.
View 3 Replies View RelatedI'll be installing a cable modem in the next few days and would like to connect my WRT310N to it. I was wondering what would be the best settings to use.
Main uses:
- Distance from WRT310N to other devices is around 8 meters, separated by 1 concrete wall
- Stream music/video from PC to iPad and another laptop wirelessly.
- Transfer files between devices
I even just reset to factory and loaded the 1.0.4 firmware but still persists.In the DNS setting, the wireless router adds itself as one of the DNS servers, and I can't figure out why it would do that. My DNS should come from my comcast router and not the e3200 wireless device.
Wireless LAN adapter Wireless Network Connection 2:
Connection-specific DNS Suffix . : hsd1.wa.comcast.net.
Description . . . . . . . . . . . : TP-LINK Wireless USB Adapter
Physical Address. . . . . . . . . : B0-48-7A-xx-xx-xx
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
[Code]....