Linksys Wireless Router :: Using E4500 As A 2nd Router?
Oct 15, 2012
due to location issues, I have to use the E4500 as a 2nd router. I have a Netgear router setup as the primary router connected to the internet, this acts as my firewall. The E4500 connected to the netgear and it route all traffic fine. The only issue I have is port forwarding to E4500. I've setup the FTP server on the E4500 and can access it via the internal network. Then on the netgear I forward the FTP port 21to the E4500. But it doesn't seem to work.
I know when I forward all my other ports, it works just fine. If I setup a FTP server on an other machine and forward that the port it works, just not the E4500. I've disabled all firewall settings on the E4500, and still nothing.
View 9 Replies
ADVERTISEMENT
Jul 4, 2012
Since the upgrade by Cisco I can only see Win7 PC's on the network. I can not see the USB drive attached to the E4500, nor can I see my Media server which is Linux based nor any Win XP computuers.
View 9 Replies
View Related
Oct 31, 2012
E4500 local network IP is 10.10.XXX.XXX and the DHCP server also starts with this subnet. My network is 192.168.XXX.XXX based but if I manually chahge the routers IP I can no longer access it. I do not use DHCP as this is in bridge mode. Why is this setup this way...CCC?
View 1 Replies
View Related
Dec 11, 2012
I just got a new E4500 and plugged a blank 2TB drive into it (Windows shows it is formatted NTFS) which was originally plugged into my WRT-610. I'm moving my media files and when it hits a 50+GB video it reports that there is not enough space to move the file. Smaller files are moving just fine.
View 4 Replies
View Related
Nov 1, 2012
I see I have 2.1.39.144146 but I don't see that version on the download page?
View 3 Replies
View Related
Oct 2, 2012
i sold off my e4200 & brought a e4500 .The e4200 has had a 2 TB W.D external drive attached ,i stream movies to a sat pvr in the .ts format .The problem is i set the e4500 up & it deleted my .ts files not once but 3 times.when i brought the e4500 i did roll the firmware back to the classic non cloud firmware.the third time i had turned the router off & once swtiched back on my files were gone .should i safely remove the drive from the set up ? what if i have a power failure?
View 5 Replies
View Related
Feb 14, 2013
I just bought a Linksys E4500. I would like some support to configure the settings regarding the 5 Ghz Bandwidth.I need to fill out the cells for Server Radius IP and port.Which are the best setting for this section?
View 3 Replies
View Related
Mar 31, 2013
My e4500 seems to be blocking my nhl gamecenter apps from playing live video on Ipad and I phones..nhl support tells me it is setting in router.?
View 6 Replies
View Related
Oct 31, 2012
I have linksys E4500 and I would like to be able to see the website visited vs ip address.Is there a way to enable same or achive same via parental controls.Again I do not want to block a website but monitor which websites are visited. Is this achievable via router or an additional software/hardware required to be used with router
View 5 Replies
View Related
Dec 31, 2012
Not sure if I have a defective router, but if I unplug it I then need to wait at least a half hour to plug it back in. Anytime sooner and it won't broadcast a SSID or connect to the modem. This is a huge inconvenience if you want to change router settings and then you need to restart.
View 1 Replies
View Related
Oct 13, 2012
Latest firmware with CCC corrupted after power outage. I reseet the e4500 several times and tried to reload the firmware and still no good. Only way I got it back up is to install the older non-CCC version 2.37. Strange all was fine until the power outage. Not sure if I should even bother to upgrade to 2.38 again.
View 2 Replies
View Related
Apr 29, 2012
Just purchased the E4500 today and install failed on both machines. Install starts and then fails to finish.I have contacted support via chat and was given manual instructions and the router will not connect to either machine.Are there known issues with the Cisco Connect software not installing?
The chat support person finally dropped out of the chat and the router remains in an unusable state.I currently had to cable wired connection of laptop to get an internet connection.
View 9 Replies
View Related
Mar 1, 2013
Im using a Linksys E4500 wireless router behind a Motorola SB6121 modem. My OS is Windows 7 and it is fully up to date. In general my entire network is working well. Now I have purchased a new IP surveillance camera and need to forward a port to be able to have remote viewing of the camera. Mi ISP blocks quite a few inbound ports including 80 so I have been trying a lot of ports all over the map to find something that will allow inbound access.
After several hours, nothing I have tried works, using a couple of different port probes including one called CanYouSeeMe I always get a "timed out" message. I have disabled the firewall in the router and on the local computer and still no luck. This says to me that either Cox is blocking nearly all ports (doubtful) or the modem is blocking access to the router somehow.
The Surfboard modem doesn't have a built in router. Unfortunately I don't have an old working modem to put in the circuit.
I don't guess it matters but the camera is accessible from all other local computers on the LAN using its IP address with a port number appended (right now it's using 8000).
View 7 Replies
View Related
May 1, 2013
I recently installed some wireless IP cameras and when attempting to re-install a camera I went into the DHCP Client table to verify which IP a camera was using to set it up, but I could not...and still cannot see any of my cameras in the table even though I can access three of them directly through the IE web browser. I initially power cycled both the E4200 router and Motorola cable modem, and then later just the wireless router...but I still do not see the devices connected. I currently have 2.0.37 firmware even though I was told by Cisco support that there was a later version available, just before being informed that I do not have support available and could purchase it. I attempted to locate a newer version, but the online upgrade portion of the Cisco Connect software searched the net and then states that I have the latest version available. I also opened a Firefox browser to see if maybe my browser was causing issues, but the same limited table appears without all entries available. I even opened the Cisco Connect software on another laptop with the same limited results. Other than a factory reset, get me E4200 dual band wireless router to show all attached devices through the DHCP Client table as it previously did approximately two weeks ago?
View 2 Replies
View Related
Jul 18, 2011
Have a 400N wireless router that has been working fine with several wireless devices on a small home network for about a year. Nothing has been changed but suddenly all of the wireless wireless devices dropped offline and none see the network signal in their search to reconnect. All of the indicator lights on the router look good and I have unplugged power and reconnected first the cable modem and then the router but still no signal. Logging into the router seems to show that it is working OK but there is apparently no air signal for the client devices to detect so only the wired devices are showing up. It's as if everything is working except the antenna function. Are there any suggestions short of uninstalling and reinstalling the whole set up and see what happens? I have taken my laptop to a nearby hotspot and confirmed that it is receiving other network signals fine so it has to be something to do with the router itself.
View 1 Replies
View Related
Dec 28, 2012
I have two mac laptops and am trying to copy a directory with a number of PDFs in it. The files aren't particularly large, but there are many of them. At some point in the process the router stops and must be turned off and on before it will respond again either wirelessly or wired. I have tried the same experiment with both devices wired and the router works fine. I have tried changing the MTU, channel, beacon setting, etc. as other forum posts have tried. I tried reflashing the firmware, resetting to factory defaults and reconfiguring. So far no success. Cisco support wants me to return the router. Frankly I'm at the point of considering the former Linksys/Cisco products complete rubbish. I am going to have to buy a new router even if I return this one since I can't be without a router for any length of time.
View 8 Replies
View Related
Jan 4, 2011
Why there is no parental control feature built in for WAP610N... how do i block website on all computers connected to my router?
View 4 Replies
View Related
Aug 9, 2012
We have a home use WRT160N router linked to a PC desktop and two wireless laptops, Yesterday bought a new I-Phone, but could not link to my network (entered the security key many times). I accidentally connected to computer fix it firm that linked to my PC and wanted a large sum to fix the problem which he said was due to large number of temp?? internet files and once removed he would change the IP address of the desktop computer? Is this diagnosis logical and can I do it on my own. The router is definetely working - both laptops access the internet and I was recently able to hook up a Samsung Blu-Ray player using the same security code I used for the I-Phone.
View 1 Replies
View Related
Mar 18, 2012
Is the Linksys E4200 Dual Band Router compatible with DHCP and VPN?
View 1 Replies
View Related
Mar 5, 2013
The router had firmware 2.0.x(?) and I tried to update to the latest FW, according to the webpage that's
FW_E1000_2.1.02.006_US_20130115.bin
Hardware is E1000 v2 according to sticker on back.The firmware update failed (no reason given) and the router now hangs in limbo where all it does is flashing the power LED.I set my PC to 19?2.168.1.2 and TFTP'd the firmware over to 192.168.1.1 - no errors reported and 192.168.1.1 is pingable. Held reset for 30s, then powered down the router for another 30s. On power-up the router still flashes the power LED.
View 3 Replies
View Related
Jun 26, 2012
I installed an IP camera, and had to change my E1000 router settings to a static IP address. Now I can't access the router settings. 192.168.1.1 is still the default gateway, but it won't open in any browser.
I'm reluctant to do a reset because it took me quite a while to figure out how to get the IP camera and port forwarding working (it does!), and I'd hate to do it all again and come to the same place. I'm not very good at this stuff, and it's a small miracle that I did it once.
View 4 Replies
View Related
Aug 27, 2008
Can you use your WRT54G router with the newer WRT310N router to extend your wireless signal? How?
View 7 Replies
View Related
Apr 6, 2012
The standard Verizon router doesn't have Wireless N capability, so I got the WRT600N (first floor) a while back and connected it to one of the ports on the Verizon router (basement). I have the wireless turned off on Verizon router. My problem is that anything connecting to the WRT600N has extremely intermittent connectivity.
View 1 Replies
View Related
Jun 20, 2010
I just got E1000 cisco wireless router. Started setup, everything worked fine and replaced admin password with my own. For some reason got error message. tried to redo setup and got message router not recognized. used laptop and found out that wireless works fine. After few days noticed that there is a (mynetworkname) guest connection you can connect without any password. i don't need that stupid thing and my question is how to disable guest network? I cannot reach Main Menu from cd and have no idea where to look for it when i connect to router by web.
View 9 Replies
View Related
Aug 15, 2011
I I use a Linksys E3000 router. Sometimes when I look at the network map I see a device called "Unknown." It appears as though the two notebooks sometime are going through this device to access the Linksys E3000. (I've checked when both notebooks are on and I can determine what devices are connecting directly to the router and what devices are going through this unknown device.) Is there any way to determine what this unknown device is?
View 5 Replies
View Related
Aug 1, 2011
I currently have my wired cable internet hooked into my wrt310n. I have that hooked into a linksys 10/100 ef3124 switch. From there, I have cat5 run to the back of my house, where the wireless signal is weakest. I've got an E2000 router and would like to hook that in at the back of the house. What settings do I need to make in order to set up a completely new wireless network in the back of the house?
View 1 Replies
View Related
Dec 12, 2011
My main Internet connection is a frontier modem /router It is on the main level of the house. In the basement I am trying to set up the cisco E3000 through an Ethernet cable.
View 4 Replies
View Related
Jan 17, 2012
I have a WRT54GS which works fine with Linux both from both wired and wireless computers using Linux. But I reinstalled Win XP and now I can't reestablish a connection following the EasyLink advisor. I did have a connection under Win XP before.
The last instruction on the Easylink advisor tells me to look for something marked "local" I don't find that word on the screen.
View 2 Replies
View Related
Dec 1, 2011
I just reset my router to the factory settings in order to make some changes to it. However, when I tried to change the SSID to a unique name, I was unable to connect my computer to the wireless network. I then reset my security settings and left the SSID to the default name "linksys_SES_54125" and it is working just fine. I tried to connect with two separate computers both running Windows 7. My router is the WRT54G v8
why I wouldn't be able to connect to my wireless network when I change the SSID?
View 5 Replies
View Related
Nov 12, 2011
My home computer accesses the Internet through an ADSL modem and a phone line. I added a wired router (Linksys BEFSR41).I've since bought a laptop computer, an iPhone4 and a wireless router (Linksys WRT160N).Again, on the advice of a friend, I ADDED the wireless router, so now have two routers connected.The devices are connected as follows:
-Wall jack to ADSL modem
-ADSL modem to BEFSR41
-BEFSR41 to WRT160N
-WRT160N to desktop computer.
As I understand Linksys routers, the default IP address for ALL Linksys routers is 192.168.1.1.Both the iPhone4 and the laptop are unable to connect to the wireless router.I'm assuming the two routers are conflicting with each other, so I thought I would remove the wired router..Can I change the IP address of the BEFSR41 router from 192.168.1.2?
Would this resolve the conflict between the two routers and allow the wireless devices to "see" the wireless router? What's the correct procedure for removing the BEFSR41 router from the system?
View 6 Replies
View Related
Aug 14, 2011
There is a way to block access to a website by password protecting it through my linksys router, which is one of thoe wrt54gs. I know I can completely block access of a website and can restrict the viewing hours of facebook at certain times through the router admin IP site but was wondering if it was possible to make it so you have to use a password to view said certain site. If there isn't is there any way maybe through a program or do I have to go through my ISP to see if they can do what I am asking for.
View 1 Replies
View Related
Feb 9, 2013
had problem with isp after they fixed problem router shortcut disappeared
View 1 Replies
View Related
Oct 17, 2008
Ok, so I reset the router but i still can't login to the setup using the factory password (admin/admin) (blank/admin) (admin/blank). Now I have an unencrypted network and no access to the setup... I even tried using the setup CD but it doesn't recognize the router.
View 2 Replies
View Related
